I need help. My p500 start after 10-15 attempts (all the time starts in emergency mode -_- ). Phone is only rooted. After connecting to the USB, computer doesn't see SD card.
I want to update soft with this guide:
http://forum.xda-developers.com/showthread.php?t=883314
When I click "read phone info" the program shuts down. When I try to launch software update, the computer restarts (blue screen...)
I try this on XP / Seven - same result.
This is my first android phone, I don't know what to do...
sorry for my english ;] I use googletranslate
hey buddy..
same happened with me.
Do this:-
remove ur battery
connect ur phone.
In KDZ Updater,In PhoneMode use CS_EMERGENCY or EMERGENCY
and then flash the KDZ File!
and do install the msxml.msi file.!
and also The read phone info hangs no matter what u do so don't worry about that!
I removed battery and KDZ works fine but now:
13:39:48 : Launching SW update
13:39:48 : Unpacking KDZ
13:39:49 : KDZ file extraced
13:39:58 : Files were extracted.
13:39:58 : LGMobileDL Load.
13:39:58 : Port = -1
13:39:58 : Connecting to phone
13:39:58 : PHONE WAS NOT FOUND!
13:40:00 : ===FINISHED===
I try emergency and csemergency. What now?
Kamillosik said:
I removed battery and KDZ works fine but now:
13:39:48 : Launching SW update
13:39:48 : Unpacking KDZ
13:39:49 : KDZ file extraced
13:39:58 : Files were extracted.
13:39:58 : LGMobileDL Load.
13:39:58 : Port = -1
13:39:58 : Connecting to phone
13:39:58 : PHONE WAS NOT FOUND!
13:40:00 : ===FINISHED===
I try emergency and csemergency. What now?
Click to expand...
Click to collapse
go to device manager ( right click on computer then properties and then open device manager )
go to modems and then disable LGE Android USB modem and LGE Virtual Modem!
This should help!
Hello.
Today I try to install recovery thunder (to flash cm7) and somehow it worked. But when I get into recovery I turned phone off... Now I'm stuck on emergency screen. I turned off everything with "LG Modem" in name and this is what I got:
[R&D Test Tools Log File]
20:22:10 : Launching SW update
20:22:10 : Unpacking KDZ
20:22:12 : KDZ file extraced
20:22:14 : Files were extracted.
20:22:14 : LGMobileDL Load.
20:22:14 : Port = -1
20:22:14 : Connecting to phone
20:22:24 : Check Phone mode = 1
20:22:43 : Phone type check.......
20:22:47 : LGMobileDL.DLL Loading....
20:22:47 : _SetAuthMark Fail
20:22:47 : AuthMark°ˇ Á¤Č®Č÷ Phoneżˇ Write µÇÁö ľĘľŇ˝Ŕ´Ď´Ů!
20:22:47 : _SetAuthMark Fail
20:22:47 : LoadCDMAPhoneData() Error
20:22:47 : _DetachDLL Call
20:22:47 : _DetachDLL Call End
20:22:47 : Param : Path = D:\Documents and Settings\All Users\Dane aplikacji\LGMOBILEAX\Phone\LGP500AT-00-V10h-EUR-XX-FEB-23-2011+0.dz
20:22:47 : Param : moduleDir =
20:22:47 : Param : waitTime = 0
20:22:47 : Param : UsbHighSpeed = 1
20:22:47 : Param : PhoneMode = 1
20:22:47 : Param : BinVersion = V10H_00
20:22:47 : Param : AuthMark = 0
20:22:47 : Call fn_StartUpgrade
20:22:55 : Smart : wParam = 100, lParam = 502
20:22:55 : Step : Upgrade Error error code = 502
20:22:55 : ResetStartInfo() Call
20:22:55 : _DetachDLL Call
20:22:55 : _DetachDLL Call End
20:22:55 : FreeLibrary Call
20:22:55 : FreeLibrary Call End
20:22:55 : ResetStartInfo() Call End
20:22:55 : ===FINISHED===
20:23:13 : OnModelDllMsg(OnMsgFromModelDll3GQCT_PDA) delete m_pLGCyonUpdate
And error window: Upgrade error, Wparam: 100, Lparam : 502
So what now my friends?
Hii me too having problem with KDZ..
I was trying to make a NANDROID backup with clockwork mod...but on doing reboot to recovery, I entered fastboot mode..
I found two methods to get it back
a) http://forum.xda-developers.com/showthread.php?t=1088046
but after the "fastboot erase recovery" command...it fails to detect my phone...stays on "waiting for phone" for very long
b)http://forum.xda-developers.com/showthread.php?t=1015332
i got the ROM from here
http://hotfile.com/dl/102451200/37eacbf/LGP500AT-00-V10c-IND-XX-DEC-08-20100-DZ.zip.html
its a .dz file but renaming it to .kdz works fine for the friend who gave me this link
however when i tried renaming it and then opening with KDZ, I got this log:
15:02:14 Launching SW update
15:02:14 Unpacking KDZ
15:02:15 KDZ file extraced (I am using exact syntax)
15:02:15 Extract file error
===FINISHED===
what is wrong and how to fix it??
This is my first android (only a week old) so not much experience ...please help
OK i went to the thread started by raar but found no help there. Heres wat happened.
-Tried LG Update Software stopped at 4% then tried restarting it didnt work.
I can access my recovery i tried the Nandroid Stock restore it did the restore but phone wont boot still it goes straight to S/W Upgrade. Can any1 help with this again i can access recovery and use it but even after restoring stock rom from nandroid it wont boot it???
wrong section. Post in q&a.
Did you go back to stock recovery? Or did you try flashing this while running CWM?
also, this:
prettyboy85712 said:
wrong section. Post in q&a.
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I tried using the LG Updater and i have the clockwork recovery i can access it jus no boot on the roms but straight to S/W Upgrade Screen
Seems like a lot of people are having this problem. I provide Android Flashing services for people in my area and I've gotten a few calls today about people who tried to use the LG Updater util and it failed at 4% and bricked their phone.
LG you fail big time. It's quite a process to get these phones working again.
dev_man77...you are too funny. Lol
Sent from my LG-P999 using XDA Premium App
it's not bricked....ugh. try using kdx on a 32 bit machine. worked for me first time after struggling with win 7 x64.
mods....please close this thread and move.
or someone can make this into a recovery stickie. i'm off to bed otherwise i'd write a guide right now. i recovered after an hour and a half of struggling with this on win 7 x64.
zgjbeta said:
I tried using the LG Updater and i have the clockwork recovery i can access it jus no boot on the roms but straight to S/W Upgrade Screen
Click to expand...
Click to collapse
restore stock 2.2 using cwm recovery, Flash stock recovery using nvflash, then try booting to 2.2 and trying the updater again.
******UPDATE FIXED THE PHONE THIS IS WHAT I DID************
As many have stated, pushing the v21E_00.kdz via the KDZ_FW_UPD program does work. It's just touchy.
This is a step by step guide to get you back in to working shape.
Note: You MUST do this via a PC running Windows XP. Running Vista/7 in compatibility mode is not going to work, period.
Part 1: Download the files you will need below.
V21E_00.kdz
KDZ_FW_UPD_EN
One-Click-G2x-recovery-flasher-06-16.rar
LG USB Drivers G2x
Part 2:
1) Install the LG G2x USB drivers to your WinXP machine.
2) Extract the entire contents of the One-Click recovery in to a folder and keep it handy.
3) Remove the battery from the phone. Hold both volume buttons and plug in the USB cable. If you are asked for a driver, look in the APX folder where you extracted the One-Click recovery archive.
4) Run OneClickRecoveryFlasher.exe and flash the stock recovery. Wait for the process to finish and close all windows and unplug the phone.
5) Put the battery back into the phone and turn it on. Now plug the USB cable back in to the phone. If everything is up to snuff you should have no driver problems at this point.
6) Extract KDZ_FW_UPD_EN.7z in to a folder. Inside is a msxml.msi. You need to run and install this first!
7) Run KDZ_FW_UPD.exe.. Leave the type set to CDMA and the phone mode set to DIAG. DO NOT CLICK ON "Read phone information"
8) Click the folder icon and load the V21E_00.kdz
9) Click launch software update (and pray!)
What you will see:
The log window will immediatly show:
22:41:02 : Launching SW update
22:41:02 : Unpacking KDZ
Then it will stop for a while.
After this you will most likely see:
22:41:16 : KDZ file extraced
22:41:21 : Files were extracted.
22:41:21 : LGMobileDL Load.
22:41:21 : Port = 5
22:41:21 : Connecting to phone
22:41:33 : Check Phone mode = 1
It will pause again before you see:
22:42:08 : Phone type check.......
22:42:08 : LGMobileDL.DLL Loading....
22:42:08 : _SetAuthMark Fail
22:42:08 : AuthMark°¡ Á¤È®È÷ Phone¿¡ Write µÇÁö ¾Ê¾Ò½À´Ï´Ù!
22:42:08 : _SetAuthMark Fail
22:42:08 : LoadCDMAPhoneData() Error
22:42:08 : _DetachDLL Call
22:42:08 : _DetachDLL Call End
22:42:08 : Param : Path = C:\Documents and Settings\All Users\Application Data\LGMOBILEAX\Phone\V21E.wdb
22:42:08 : Param : moduleDir =
22:42:08 : Param : waitTime = 33000
22:42:08 : Param : UsbHighSpeed = 0
22:42:08 : Param : PhoneMode = 1
22:42:08 : Param : BinVersion = V21E_00
22:42:08 : Param : AuthMark = 0
22:42:08 : Call fn_StartUpgrade
Finally after another pause you should start to get spammed by the following message:
22:42:41 : CDMA: wParam = 2007, lParam = 0
22:42:41 : Model Dll Msg Not Found(2007, 0)
You will even hear the USB disconnect/reconnect sound several times.
The sound and spam will continue until the lParam counts to 100.
It should look like:
22:46:25 : CDMA: wParam = 2005, lParam = 100
22:46:25 : Model Dll Msg Not Found(2005, 100)
22:46:25 : CDMA: wParam = 2001, lParam = 0
22:46:25 : Model Dll Msg Not Found(2001, 0)
After it gets to 100, your phone will reboot to the LG logo before going
blank. After a few moments of the blank screen you will get the TMO G2x splash before being dropped back in to your working phone.
Be patient as this takes a while. If at any point the program freezes for more than a few moments, it's most likely going to fail and you will need to try again.
Hope this helps. =)
Thanks to everyone who helped figure this out.
Thread moved to proper forum. Please post in the correct sections!
How about some links?
Can you post links for download
zgjbeta said:
******UPDATE FIXED THE PHONE THIS IS WHAT I DID************
As many have stated, pushing the v21E_00.kdz via the KDZ_FW_UPD program does work. It's just touchy.
This is a step by step guide to get you back in to working shape.
Note: You MUST do this via a PC running Windows XP. Running Vista/7 in compatibility mode is not going to work, period.
Part 1: Download the files you will need below.
V21E_00.kdz
KDZ_FW_UPD_EN
One-Click-G2x-recovery-flasher-06-16.rar
LG USB Drivers G2x
Part 2:
1) Install the LG G2x USB drivers to your WinXP machine.
2) Extract the entire contents of the One-Click recovery in to a folder and keep it handy.
3) Remove the battery from the phone. Hold both volume buttons and plug in the USB cable. If you are asked for a driver, look in the APX folder where you extracted the One-Click recovery archive.
4) Run OneClickRecoveryFlasher.exe and flash the stock recovery. Wait for the process to finish and close all windows and unplug the phone.
5) Put the battery back into the phone and turn it on. Now plug the USB cable back in to the phone. If everything is up to snuff you should have no driver problems at this point.
6) Extract KDZ_FW_UPD_EN.7z in to a folder. Inside is a msxml.msi. You need to run and install this first!
7) Run KDZ_FW_UPD.exe.. Leave the type set to CDMA and the phone mode set to DIAG. DO NOT CLICK ON "Read phone information"
8) Click the folder icon and load the V21E_00.kdz
9) Click launch software update (and pray!)
What you will see:
The log window will immediatly show:
22:41:02 : Launching SW update
22:41:02 : Unpacking KDZ
Then it will stop for a while.
After this you will most likely see:
22:41:16 : KDZ file extraced
22:41:21 : Files were extracted.
22:41:21 : LGMobileDL Load.
22:41:21 : Port = 5
22:41:21 : Connecting to phone
22:41:33 : Check Phone mode = 1
It will pause again before you see:
22:42:08 : Phone type check.......
22:42:08 : LGMobileDL.DLL Loading....
22:42:08 : _SetAuthMark Fail
22:42:08 : AuthMark°¡ Á¤È®È÷ Phone¿¡ Write µÇÁö ¾Ê¾Ò½À´Ï´Ù!
22:42:08 : _SetAuthMark Fail
22:42:08 : LoadCDMAPhoneData() Error
22:42:08 : _DetachDLL Call
22:42:08 : _DetachDLL Call End
22:42:08 : Param : Path = C:\Documents and Settings\All Users\Application Data\LGMOBILEAX\Phone\V21E.wdb
22:42:08 : Param : moduleDir =
22:42:08 : Param : waitTime = 33000
22:42:08 : Param : UsbHighSpeed = 0
22:42:08 : Param : PhoneMode = 1
22:42:08 : Param : BinVersion = V21E_00
22:42:08 : Param : AuthMark = 0
22:42:08 : Call fn_StartUpgrade
Finally after another pause you should start to get spammed by the following message:
22:42:41 : CDMA: wParam = 2007, lParam = 0
22:42:41 : Model Dll Msg Not Found(2007, 0)
You will even hear the USB disconnect/reconnect sound several times.
The sound and spam will continue until the lParam counts to 100.
It should look like:
22:46:25 : CDMA: wParam = 2005, lParam = 100
22:46:25 : Model Dll Msg Not Found(2005, 100)
22:46:25 : CDMA: wParam = 2001, lParam = 0
22:46:25 : Model Dll Msg Not Found(2001, 0)
After it gets to 100, your phone will reboot to the LG logo before going
blank. After a few moments of the blank screen you will get the TMO G2x splash before being dropped back in to your working phone.
Be patient as this takes a while. If at any point the program freezes for more than a few moments, it's most likely going to fail and you will need to try again.
Hope this helps. =)
Thanks to everyone who helped figure this out.
Click to expand...
Click to collapse
kolobok01 said:
Can you post links for download
Click to expand...
Click to collapse
here's the kdz file
http://csmg.lgmobile.com:9002/swdata/WEBSW/LGP999DW/ATMODW/V21e_00/V21E_00.kdz
and here's the kdz flasher
http://www.mediafire.com/?3hd4ao113lx8gq4
dev_man77 said:
Click to expand...
Click to collapse
You my friend just posted the most useless post in the history of xda.
Your contribution to this community is just phenomenal.
This is why people hate this site.
What a ****!
zgjbeta said:
******UPDATE FIXED THE PHONE THIS IS WHAT I DID************
As many have stated, pushing the v21E_00.kdz via the KDZ_FW_UPD program does work. It's just touchy.
This is a step by step guide to get you back in to working shape.
Note: You MUST do this via a PC running Windows XP. Running Vista/7 in compatibility mode is not going to work, period.
Part 1: Download the files you will need below.
V21E_00.kdz
KDZ_FW_UPD_EN
One-Click-G2x-recovery-flasher-06-16.rar
LG USB Drivers G2x
Part 2:
1) Install the LG G2x USB drivers to your WinXP machine.
2) Extract the entire contents of the One-Click recovery in to a folder and keep it handy.
3) Remove the battery from the phone. Hold both volume buttons and plug in the USB cable. If you are asked for a driver, look in the APX folder where you extracted the One-Click recovery archive.
4) Run OneClickRecoveryFlasher.exe and flash the stock recovery. Wait for the process to finish and close all windows and unplug the phone.
5) Put the battery back into the phone and turn it on. Now plug the USB cable back in to the phone. If everything is up to snuff you should have no driver problems at this point.
6) Extract KDZ_FW_UPD_EN.7z in to a folder. Inside is a msxml.msi. You need to run and install this first!
7) Run KDZ_FW_UPD.exe.. Leave the type set to CDMA and the phone mode set to DIAG. DO NOT CLICK ON "Read phone information"
8) Click the folder icon and load the V21E_00.kdz
9) Click launch software update (and pray!)
What you will see:
The log window will immediatly show:
22:41:02 : Launching SW update
22:41:02 : Unpacking KDZ
Then it will stop for a while.
After this you will most likely see:
22:41:16 : KDZ file extraced
22:41:21 : Files were extracted.
22:41:21 : LGMobileDL Load.
22:41:21 : Port = 5
22:41:21 : Connecting to phone
22:41:33 : Check Phone mode = 1
It will pause again before you see:
22:42:08 : Phone type check.......
22:42:08 : LGMobileDL.DLL Loading....
22:42:08 : _SetAuthMark Fail
22:42:08 : AuthMark°¡ Á¤È®È÷ Phone¿¡ Write µÇÁö ¾Ê¾Ò½À´Ï´Ù!
22:42:08 : _SetAuthMark Fail
22:42:08 : LoadCDMAPhoneData() Error
22:42:08 : _DetachDLL Call
22:42:08 : _DetachDLL Call End
22:42:08 : Param : Path = C:\Documents and Settings\All Users\Application Data\LGMOBILEAX\Phone\V21E.wdb
22:42:08 : Param : moduleDir =
22:42:08 : Param : waitTime = 33000
22:42:08 : Param : UsbHighSpeed = 0
22:42:08 : Param : PhoneMode = 1
22:42:08 : Param : BinVersion = V21E_00
22:42:08 : Param : AuthMark = 0
22:42:08 : Call fn_StartUpgrade
Finally after another pause you should start to get spammed by the following message:
22:42:41 : CDMA: wParam = 2007, lParam = 0
22:42:41 : Model Dll Msg Not Found(2007, 0)
You will even hear the USB disconnect/reconnect sound several times.
The sound and spam will continue until the lParam counts to 100.
It should look like:
22:46:25 : CDMA: wParam = 2005, lParam = 100
22:46:25 : Model Dll Msg Not Found(2005, 100)
22:46:25 : CDMA: wParam = 2001, lParam = 0
22:46:25 : Model Dll Msg Not Found(2001, 0)
After it gets to 100, your phone will reboot to the LG logo before going
blank. After a few moments of the blank screen you will get the TMO G2x splash before being dropped back in to your working phone.
Be patient as this takes a while. If at any point the program freezes for more than a few moments, it's most likely going to fail and you will need to try again.
Hope this helps. =)
Thanks to everyone who helped figure this out.
Click to expand...
Click to collapse
I can confirm this does work. I am one person who has experienced every problem each person has expressed when attempting the update. I got that crazy status 2010-3015 error, couldn't find phone error, no communication error.
The trick is using mode XP if u have windows 7. I disabled the LG modem driver in windows 7 so Mode XP wouldn't have to fight with win 7 when the phone would USB connect/disconnect.
The above method works but it is VERY touchy as mentioned. I almost ended up sending my phone to LG but I kept with it ...reflashing stock recovery via nvflash in mode xp and letting the LG mobile tool download drivers and installing them is what caused my app to no longer freeze when connecting my phone.
I spent about 8 hours trying to fix my phone. Its possible but u must be patient and persistent. As long as your comp can recognize your phone when u plug it in, i promise u can debrick it. Ill post my steps when I get to work.
Sent from my LG-P999 using XDA App
okay here is the trick***
i was getting that error 3012 over and over again... and i saw ergibson83's post about disabling drivers for the lg on windows 7... what i did was this.
when you are running kdz using xp mode on windows 7 ultimate and it begins the IParam count to 100, keep your eye on the usb connectivity. Up top of the screen of XP Mode, you will see the usb tab. when you hear windows 7 trying to grab the device, go up top and reattach the LG Modem and it will continue the count.
Around 50, it did it again.. so i clicked reattach for the second time. Then it reached 100 and i was golden!
now i have beautiful gb running flawless
Hope this works for those running XP Mode.
i have windows 7 how can i get it to xp mode plz help
Gryncc said:
i have windows 7 how can i get it to xp mode plz help
Click to expand...
Click to collapse
Download it from the Microsoft site. Its free
Sent from my LG-P999 using XDA App
zgjbeta said:
OK i went to the thread started by raar but found no help there. Heres wat happened.
-Tried LG Update Software stopped at 4% then tried restarting it didnt work.
I can access my recovery i tried the Nandroid Stock restore it did the restore but phone wont boot still it goes straight to S/W Upgrade. Can any1 help with this again i can access recovery and use it but even after restoring stock rom from nandroid it wont boot it???
Click to expand...
Click to collapse
After a week with the same problem and intensive google search, did this:
Booted into XP downloaded "mcci r firmware update driver for mtk.exe" installed the same (does not install in Win7 environment). started the KDZ_FW_UPD_EN tool and using the update start in the main window managed to update successfully to Gingerbread, now I need to get out of T-mobile's clutches and get cyanogenmod..Any suggestions. Hope my workaround helps.
Before this success I tried everything possible including a visit to a LG Service centre in Chennai who did try sincerely to help but could not. The past week was really frustrating which I do not want to list here but my request is don't give up.
I subsequently checked with LG Service centre telling them I succeeded and described the way I did it. They said they also have XP with the firmware updated and tried it out of 2 different PC's but could not manage the update. Then I tried recollecting what I did try differently and I could see this may be the trick that enabled it to succeed. Before I tried the firmware update. I tried the tool clicked on Phone information in the main indow (both in Win 7 and XP) and then clicked on update start at the bottom of the subsequent window. The tool did collect information and went all the way extracting files rechecking EMEI upto MTK start when the tool kept crashing and failed to update.It is only after this failure did I try the firmware update and running the tool when it succeeded.
Thank my stars I did not format my XP partition which I wanted to last month but did not find the time. If only one person is benefited by this post I would be most glad
I am having a mare and hope someone can help please.
I want to flash this rom but have had to revert back to Froyo and can't seem to flash GB or GB baseband onto my phone. The KDZ installer either has an error unpacking file or when I get past that, just won't work (I think this is because of the LG version 9 that I've read about - I have now been able to revert it to 8 and still not working).
Also, installed ROM manager from Market and it didn't have an option for the LG O3D so couldn't use it.
Sorry if I sound like a complete NOOB, flashed GB and other stuff before on the KDZ installer but it doesn't like me any more and I can't seem to do it either way. I really want to install this ROM.
Here is a copy of the KDZ log file that it always fails on:
[R&D Test Tools Log File]
17:36:54 : Launching SW update
17:36:54 : Unpacking KDZ
17:38:48 : KDZ file extraced
17:40:24 : Files were extracted.
17:40:24 : LGMobileDL Load.
17:40:30 : Port = 0
17:40:36 : Connecting to phone
17:40:52 : Check Phone mode = 1
17:41:22 : Phone type check.......
17:41:58 : _DetachDLL Call
17:41:58 : _DetachDLL Call End
17:41:58 : Param : Path = C:\Documents and Settings\All Users\Application Data\LGMOBILEAX\Phone\V21A.wdb
17:41:58 : Param : moduleDir =
17:41:58 : Param : waitTime = 0
17:41:58 : Param : UsbHighSpeed = 1
17:41:58 : Param : PhoneMode = 1
17:41:58 : Param : BinVersion = V21A_00(2)
17:41:58 : Param : AuthMark = 0
17:41:58 : Call fn_StartUpgrade
17:41:58 : CDMA: wParam = 2004, lParam = 5
17:41:58 : Model Dll Msg Not Found(2004, 5)
17:42:18 : CDMA: wParam = 2004, lParam = 6
17:42:18 : Model Dll Msg Not Found(2004, 6)
17:42:23 : CDMA: wParam = 2004, lParam = 7
17:42:23 : Model Dll Msg Not Found(2004, 7)
17:42:23 : CDMA: wParam = 2007, lParam = 0
17:42:23 : Model Dll Msg Not Found(2007, 0)
17:42:23 : CDMA: wParam = 2010, lParam = 3002
17:42:23 : Model Dll Msg Not Found(2010, 3002)
Cheers
I had the exact same problem all i did was re download the kdz file again it worked something must of happened while downloading data got broken all you have to do is download a fresh copy and your on your way..
I will try it thanks it's driving me mad!
try this rom manager,this one works.
I think the problem might be a corrupted KDZ file but I can't get another to download please help someone as the LG site link just freezes up.
Here is the link find your country and download the kdz...
http://lg-phone-firmware.com/index.php?id_mod=2
Hi All,
I have a GW620 wich I want to upgrade to 2.3
Problem is, somehow I can't downgrade my firmware. It's stuck.
Am using Windows 7 Home Premium x32 and all the apps I use I open it with Administrator privileges..
Also have .net 3.5 and xsxml 4.0 (or something like that, don't know the exact name anymore)
Can't enable root permission via the hidden menu, and all fastboot combinations I have tried fail (and i've tried it really MANY times at all possible timings).
I can get ADB to work and boot to emergency mode but that still won't do.
A full factory reset doesn't help either..
I have the V20D_00 firmware. Is it completely locked or something? Anyone can help me wit this one?
Here more details about the phone:
Model Number:
LG-GW620
Android Version:
2.2
Kernel Version:
2.6.32.9
[email protected])
#1 PREEMPT Tue Jan 4 11:44:31 EST 2011
Build Number:
Froyo.v20d
Software Version:
GW620-V20d
Click to expand...
Click to collapse
and the error log if I try to install it without root permissions or without fastboot:
22:11:22 : Launching SW update
22:11:22 : Unpacking KDZ
22:11:26 : KDZ file extraced
22:11:26 : Files were extracted.
22:11:26 : LGMobileDL Load.
22:11:26 : Port = 4
22:11:26 : Connecting to phone
22:11:36 : Check Phone mode = 1
22:11:54 : Phone type check.......
22:11:54 : LGMobileDL.DLL Loading....
22:11:54 : _SetAuthMark Ok : wAuthMark(6801)
22:11:54 : _DetachDLL Call
22:11:54 : _DetachDLL Call End
22:11:54 : Param : Path = C:\ProgramData\LGMOBILEAX\Phone\GW620AT-00-V10g-EUY-XX-DEC-30-2009+0.dz
22:11:54 : Param : moduleDir =
22:11:54 : Param : waitTime = 0
22:11:54 : Param : UsbHighSpeed = 1
22:11:54 : Param : PhoneMode = 1
22:11:54 : Param : BinVersion = V10G_00
22:11:54 : Param : AuthMark = 6801
22:11:54 : Call fn_StartUpgrade
22:11:59 : 3GQCT : wParam = 4, lParam = 0
22:11:59 : Step Complete : DLOAD Change
22:12:39 : 3GQCT : wParam = 3, lParam = 0
22:12:39 : Step Complete : C Drive Erase
22:12:39 : 3GQCT : wParam = 205, lParam = 0
22:12:40 : 3GQCT : wParam = 100, lParam = 4008
22:12:40 : Step : Upgrade Error error code = 4008
22:12:40 : ResetStartInfo() Call
22:12:40 : _DetachDLL Call
22:12:40 : _DetachDLL Call End
22:12:40 : FreeLibrary Call
22:12:40 : FreeLibrary Call End
22:12:40 : ResetStartInfo() Call End
22:12:40 : ===FINISHED===
Click to expand...
Click to collapse
Got it working now.
Found a version v20d_00 with fastboot, and that version did install without a problem.
For future readers I have uploaded the kdz. Also found a version for v20g_00 so uploaded that one also. Have tested them both and they are working.
V20D_00_Fastboot
V20G_00_Fastboot
I have the same problem. At the time of cwm installing, my phone rebooted on emergency mode yellow screen and cant open anymore. I use vol+ + power and the computer recognize my phone. I diasbled LGE modem and try to install v10A, V10C, v10g and v10h firmware every time it cant finish correctly and say
[R&D Test Tools Log File]
14:00:22 : Launching SW update
14:00:22 : Unpacking KDZ
14:00:37 : KDZ file extraced
14:00:43 : Files were extracted.
14:00:43 : LGMobileDL Load.
14:00:43 : Port = -1
14:00:43 : Connecting to phone
14:00:52 : Check Phone mode = 2
14:01:09 : Phone type check.......
14:01:15 : _DetachDLL Call
14:01:15 : _DetachDLL Call End
14:01:15 : Param : Path = D:\ProgramData\LGMOBILEAX\Phone\LGP705AT-00-V10c-TUR-XX-JUL-19-2012+0.dz
14:01:15 : Param : moduleDir =
14:01:15 : Param : waitTime = 0
14:01:15 : Param : UsbHighSpeed = 1
14:01:15 : Param : PhoneMode = 2
14:01:15 : Param : BinVersion = V10C_00
14:01:15 : Param : AuthMark = 0
14:01:15 : Call fn_StartUpgrade
14:01:15 : CDMA: wParam = 206, lParam = 0
14:01:15 : Model Dll Msg Not Found(206, 0)
upgrade error wParam:100 lParam: 1002
how can I fix this problem
Did You try revert to original recovery with fastboot command?
Sent from my LG-P700 using xda app-developers app
How I can do this can you explain me. About 1 week more than 50 hours I try to solve problem but I cant do this. I downloaded android sdk and I try to start comannd
d:\andorid-sdk\platform-tools\fastboot oem unlock enter
but it cant find my LG p700
I connect my phone with vol+ and power buttun clicking and install usb drivers after that I disable lg modem and open update tool and costumer support recıver my phone, enter imei say ok , go to update program after waiting it says " pdater not possible due to fatal error, while the LG Mobile Phone Software Update"
I used a lot of buttun combinations to go cwm but it always stuck in yellow screen emergency mode. I need your helps however I will be carzy, I have a big headache
thank you so much
drberkantkaya said:
How I can do this can you explain me. About 1 week more than 50 hours I try to solve problem but I cant do this. I downloaded android sdk and I try to start comannd
d:\andorid-sdk\platform-tools\fastboot oem unlock enter
but it cant find my LG p700
I connect my phone with vol+ and power buttun clicking and install usb drivers after that I disable lg modem and open update tool and costumer support recıver my phone, enter imei say ok , go to update program after waiting it says " pdater not possible due to fatal error, while the LG Mobile Phone Software Update"
I used a lot of buttun combinations to go cwm but it always stuck in yellow screen emergency mode. I need your helps however I will be carzy, I have a big headache
thank you so much
Click to expand...
Click to collapse
1. Reinstall drivers
2. Use uptestex_mod2_marwin.exe (no 2nd one)
ryba84 said:
Did You try revert to original recovery with fastboot command?
Sent from my LG-P700 using xda app-developers app
Click to expand...
Click to collapse
I got the same problem now Can you tell me step by step what I have to do?
[R&D Test Tools Log File]
00:12:23 : Launching SW update
00:12:23 : Unpacking KDZ
00:12:25 : KDZ file extraced
00:12:27 : Files were extracted.
00:12:27 : LGMobileDL Load.
00:12:27 : Port = -1
00:12:27 : Connecting to phone
00:12:37 : Check Phone mode = 2
00:12:53 : Phone type check.......
00:12:55 : _DetachDLL Call
00:12:55 : _DetachDLL Call End
00:12:55 : Param : Path = C:\ProgramData\LGMOBILEAX\Phone\LGP700AT-00-V20d-262-000-MAY-02-2013+0.dz
00:12:55 : Param : moduleDir =
00:12:55 : Param : waitTime = 0
00:12:55 : Param : UsbHighSpeed = 1
00:12:55 : Param : PhoneMode = 2
00:12:55 : Param : BinVersion = V20D_00
00:12:55 : Param : AuthMark = 0
00:12:55 : Call fn_StartUpgrade
00:12:55 : CDMA: wParam = 206, lParam = 0
00:12:55 : Model Dll Msg Not Found(206, 0)