Related
I understand that in order to flash a ROM you need to select the wipe data/factory reset button in CWM recovery. But I can't find any thread that answers various questions:
1) Does the phone need to be plugged in during this?
2) Does the battery need to be at a certain level? (obviously not near dead, but maybe 100% or closest possible mandatory?)
3) What needs to be set on the phone before turning it off and going into recovery? debugging turned on? mount or unmount anything?
4) While in recovery, should I select to have my data, cache, sd card mounted or unmounted?
5) Some threads say to use the format options in recovery. Should I format /sdcard and-or /system ?
6) USB storage is the External SD card, correct?
7) If I have CWM located on the Ext. SD card, do I need to mount it via CWM recovery screen or do anything else differently before I begin flashing a ROM?
Thanks!
el buho said:
I understand that in order to flash a ROM you need to select the wipe data/factory reset button in CWM recovery. But I can't find any thread that answers various questions:
1) Does the phone need to be plugged in during this?
2) Does the battery need to be at a certain level? (obviously not near dead, but maybe 100% or closest possible mandatory?)
3) What needs to be set on the phone before turning it off and going into recovery? debugging turned on? mount or unmount anything?
4) While in recovery, should I select to have my data, cache, sd card mounted or unmounted?
5) Some threads say to use the format options in recovery. Should I format /sdcard and-or /system ?
6) USB storage is the External SD card, correct?
7) If I have CWM located on the Ext. SD card, do I need to mount it via CWM recovery screen or do anything else differently before I begin flashing a ROM?
Thanks!
Click to expand...
Click to collapse
It was recommended to me to have it unplugged before entering into CWM. I read the battery "should" be over 50% because JUST IN CASE, you don't want to run out of battery in the middle of a flash...but with this phone, flashing is so quick anyway...but still, personally, I make sure it's over 50%. I haven't messed with any mounting/unmounting features in CWM during flashing. Whether to format your sdcard or not should be obvious to you...it has nothing to do with flashing a rom or kernal...it's for setting up a new sd card for putting apps, storage, and/or swap. As far as CWM being located on the external sd card, I don't really understand. You should use NVFlash to flash CWM to your phone (with external support)...if you dig around these threads, you'll see a One Click NVFlash tutorial and software. I hope this helps. I"m new too...I've learned all this by reading these forums this past week.
I already did the NVFlash etc. But at one point in the recovery procedure you have to press a button saying Flash CWM to External SD card or Flash CWM to Internal SD card and the forums said it really doesn't matter, so I went with external.
That meant that when you load up CWM, it will allow you to browse in your external card for the roms, kernals, mods, etc. that you wanna flash...so that's where you'll store that stuff that you'd like to flash. If you had selected "internal", then CWM would only allow you to browse your internal card.
el buho said:
I understand that in order to flash a ROM you need to select the wipe data/factory reset button in CWM recovery. But I can't find any thread that answers various questions:
1) Does the phone need to be plugged in during this? No
2) Does the battery need to be at a certain level? (obviously not near dead, but maybe 100% or closest possible mandatory?) No, but you don't want it to be at 5%.
3) What needs to be set on the phone before turning it off and going into recovery? debugging turned on? mount or unmount anything? Nothing
4) While in recovery, should I select to have my data, cache, sd card mounted or unmounted? Don't touch anything in regards to mounting.
5) Some threads say to use the format options in recovery. Should I format /sdcard and-or /system ? Just /system usually.
6) USB storage is the External SD card, correct? Correct
7) If I have CWM located on the Ext. SD card, do I need to mount it via CWM recovery screen or do anything else differently before I begin flashing a ROM? No
Thanks!
Click to expand...
Click to collapse
Answers in bold.
I have the ATT One X and and installed a font that froze the phone so i went in CWM to restore but ive seemed to have erased everything in the sd card and don't know what to do. Can someone please help.
OptimusSteel34 said:
I have the ATT One X and and installed a font that froze the phone so i went in CWM to restore but ive seemed to have erased everything in the sd card and don't know what to do. Can someone please help.
Click to expand...
Click to collapse
Yea go to cnet.com and download Recuva. Connect ur phone to computer. Run Recuva enable deep scan and you stuff will be restored
Sent from my HTC One X using xda app-developers app
boot ur phone to bootloader and run ruu
Try going into Recovery, and wipe cache and wipe Dalvik, then reboot.
Not sure if this will work on the One X. But I've had occasional issues with the internal SD mounting on my HTC Flyer tablet, and wiping cache and Dalvik fix it every time.
Its worth a try, anyway.
If your problem is that you cannot mount the SDCard (as opposed to being able to mount it but it is empty) I ran into something similar during my 2nd ROM flashing experience. I got into this state by doing a factory wipe from the bootloader screen (as opposed to doing it from recovery). This wiped my entire SDCard partition, even the filesystem on it. So when I booted into Android, it failed to mount the SDCard altogether, saying that it was corrupted.
I had to re-format the SDCard from Windows in order to recover, by doing the following:
1. Boot into recovery (for me was TWRP 2.1.8.1)
2. Select "Mount"
3. Checkmark "Mount SDCard"
4. Connect device to PC via USB cable
5. Select "Mount USB Storage" in TWRP
6. On the PC, find the SDCard's drive in My Computer, right-click on it, and select "Format"
7. Proceed with formatting the SDCard ("Quick Format" is fine)
8. Safely remove the USB storage from Windows
9. Reboot the device
Upon rebooting, the SDCard mounted fine, although all data was erased.
Lesson learned: do factory reset from recovery, not the bootloader screen
denversc said:
If your problem is that you cannot mount the SDCard (as opposed to being able to mount it but it is empty) I ran into something similar during my 2nd ROM flashing experience. I got into this state by doing a factory wipe from the bootloader screen (as opposed to doing it from recovery). This wiped my entire SDCard partition, even the filesystem on it. So when I booted into Android, it failed to mount the SDCard altogether, saying that it was corrupted.
I had to re-format the SDCard from Windows in order to recover, by doing the following:
1. Boot into recovery (for me was TWRP 2.1.8.1)
2. Select "Mount"
3. Checkmark "Mount SDCard"
4. Connect device to PC via USB cable
5. Select "Mount USB Storage" in TWRP
6. On the PC, find the SDCard's drive in My Computer, right-click on it, and select "Format"
7. Proceed with formatting the SDCard ("Quick Format" is fine)
8. Safely remove the USB storage from Windows
9. Reboot the device
Upon rebooting, the SDCard mounted fine, although all data was erased.
Lesson learned: do factory reset from recovery, not the bootloader screen
Click to expand...
Click to collapse
I'm having the same issue, but I can't check the SD card box in TWRP?
Any idea what I can do to fix this?
I had the same issue. however if you USB to PC and format sd drive, twrp will sometimes find. Also notice that when I did that my rom zip, kernal files to flash were in the twrp file in recovery.
Make sure you have everything backed up.
I guess I should add that twrp wouldn't mount however USB to PC still found it.
Sent from my HTC One X using xda app-developers app
Dandan8118 said:
I'm having the same issue, but I can't check the SD card box in TWRP?
Any idea what I can do to fix this?
Click to expand...
Click to collapse
Ditto, exact same problem. Any solutions?
I've been having the same problems. My phone has been in a soft brick for 1 week and a half now and nothing seems to work.
Suggestions I've been given (None worked for me):
-Hold power button for 10 seconds for a force reboot
-Flash stock recovery, go in Hboot, Clear Storage, Flash TWRP, wipe cache.
-Connect an SD card reader to your phone with the rom in it.
-Partition SD from TWRP
-Relock phone and flash stock RUU (My phone is on 1.94 firmware and there is no equivalent RUU. I tried all of them and they all say I have the wrong ROM)
The only suggestion I have been given that would work is to buy a new phone... But I am not that desperate yet.
Maybe one will work for you
Dandan8118 said:
I can't check the SD card box in TWRP? Any idea what I can do to fix this?
Click to expand...
Click to collapse
Now that I think of it, it is probably not necessary to checkmark "Mount SDCard". The reason is that doing so only mounts (or unmounts) it for access within TWRP and should not affect the USB access. So if you cannot checkmark it, try just ignoring that step.
denversc said:
Now that I think of it, it is probably not necessary to checkmark "Mount SDCard". The reason is that doing so only mounts (or unmounts) it for access within TWRP and should not affect the USB access. So if you cannot checkmark it, try just ignoring that step.
Click to expand...
Click to collapse
Umm huge thanks, button not enough. Thought I'd have to start from scratch again! Will keep in mind in case of future issues.
Sent from my HTC One X using Tapatalk 2
So, wait, I'm having the same issue. How did you get your phone to a bootable condition without erasing the SD card?
wormyrocks said:
So, wait, I'm having the same issue. How did you get your phone to a bootable condition without erasing the SD card?
Click to expand...
Click to collapse
I didn't. I had to wipe the SDCard by formatting it. More correctly, the factory reset that I performed from hboot wiped the SDCard, so it was already wiped... I just had to format it. Lesson learned: only perform factory reset from recovery (TWRP or CWM), as it does not touch the SDCard.
denversc said:
I didn't. I had to wipe the SDCard by formatting it. More correctly, the factory reset that I performed from hboot wiped the SDCard, so it was already wiped... I just had to format it. Lesson learned: only perform factory reset from recovery (TWRP or CWM), as it does not touch the SDCard.
Click to expand...
Click to collapse
Ah, guess mine is gone then. Damn it.
wormyrocks said:
Ah, guess mine is gone then. Damn it.
Click to expand...
Click to collapse
My phone is now booting, but it still can't mount or recognize the SD card. Do I have to reflash again or is there some setting I can use to get it to mount?
I did this and this is what Xsmagical and I did to fix it.
Take the stock android recovery from a ruu or stock Rom. (I used the one from 1.85 ruu but it doesn't matter.)
Fastboot flash the stock recovery to your phone and then reboot into bootloader where you originally wiped.
Factory reset from hboot and then Fastboot flash twrp again, mount sd should be available now. Mount sd, copy whatever Rom onto sd card and flash from there.
Freaked me out too man
Sent from my JellyBean
ChongoDroid said:
I did this and this is what Xsmagical and I did to fix it.
Take the stock android recovery from a ruu or stock Rom. (I used the one from 1.85 ruu but it doesn't matter.)
Fastboot flash the stock recovery to your phone and then reboot into bootloader where you originally wiped.
Factory reset from hboot and then Fastboot flash twrp again, mount sd should be available now. Mount sd, copy whatever Rom onto sd card and flash from there.
Freaked me out too man
Sent from my JellyBean
Click to expand...
Click to collapse
How does one extract the stock recovery from a ruu or stock ROM? (or, would it be possible for you to send me the file?)
and does flashing the stock recovery require me to relock the bootloader?
thx u dolan
Gracias
ChongoDroid said:
I did this and this is what Xsmagical and I did to fix it.
Take the stock android recovery from a ruu or stock Rom. (I used the one from 1.85 ruu but it doesn't matter.)
Fastboot flash the stock recovery to your phone and then reboot into bootloader where you originally wiped.
Factory reset from hboot and then Fastboot flash twrp again, mount sd should be available now. Mount sd, copy whatever Rom onto sd card and flash from there.
Freaked me out too man
Sent from my JellyBean
Click to expand...
Click to collapse
muchas gracias!!
denversc said:
if your problem is that you cannot mount the sdcard (as opposed to being able to mount it but it is empty) i ran into something similar during my 2nd rom flashing experience. I got into this state by doing a factory wipe from the bootloader screen (as opposed to doing it from recovery). This wiped my entire sdcard partition, even the filesystem on it. So when i booted into android, it failed to mount the sdcard altogether, saying that it was corrupted.
I had to re-format the sdcard from windows in order to recover, by doing the following:
1. Boot into recovery (for me was twrp 2.1.8.1)
2. Select "mount"
3. Checkmark "mount sdcard"
4. Connect device to pc via usb cable
5. Select "mount usb storage" in twrp
6. On the pc, find the sdcard's drive in my computer, right-click on it, and select "format"
7. Proceed with formatting the sdcard ("quick format" is fine)
8. Safely remove the usb storage from windows
9. Reboot the device
upon rebooting, the sdcard mounted fine, although all data was erased.
Lesson learned: Do factory reset from recovery, not the bootloader screen
Click to expand...
Click to collapse
i love you sir saved my ass
I'm having these troubles for sure.
Rooted, tried loading CM10, got stuck on the looping CM screen.
Originally Posted by denversc
if your problem is that you cannot mount the sdcard (as opposed to being able to mount it but it is empty) i ran into something similar during my 2nd rom flashing experience. I got into this state by doing a factory wipe from the bootloader screen (as opposed to doing it from recovery). This wiped my entire sdcard partition, even the filesystem on it. So when i booted into android, it failed to mount the sdcard altogether, saying that it was corrupted.
I had to re-format the sdcard from windows in order to recover, by doing the following:
1. Boot into recovery (for me was twrp 2.1.8.1)
2. Select "mount"
3. Checkmark "mount sdcard"
4. Connect device to pc via usb cable
5. Select "mount usb storage" in twrp
6. On the pc, find the sdcard's drive in my computer, right-click on it, and select "format"
7. Proceed with formatting the sdcard ("quick format" is fine)
8. Safely remove the usb storage from windows
9. Reboot the device
I followed all the steps, but I'm stuck in TWRP recovery, I can't boot anything past it and I'm lost as to what to do. =\
Im currently stuck in recovery without a rom to reboot too, because i forgot to put the zip in before. I'm trying to mount to storage using 4EXT Recovery touch, just cant seem to open my sd folder. I tried mounting sdcard and mounting system through the mounts/storage, no luck. Any help?
ptrle said:
Im currently stuck in recovery without a rom to reboot too, because i forgot to put the zip in before. I'm trying to mount to storage using 4EXT Recovery touch, just cant seem to open my sd folder. I tried mounting sdcard and mounting system through the mounts/storage, no luck. Any help?
Click to expand...
Click to collapse
Select toggle USB storage and access from computer. Put a Rom on and then eject from computer then select install from sd card.
Sent from my Inspire 4G using xda premium
I am relatively new to the world of rooting and ROMs, but I have successfully installed CM10 on a previous Samsung phone, so I am decently literate.
I am currently attempting to install CM10.1 on my Verizon Galaxy S III (following the instructions on the Install CM for d2vzw page on the CM wiki), but I have reached an impasse at step 7. I was not aware that I had to put the VRALE6.bootloader.zip file on the SD card before starting this process, so I am now attempting to get that file onto my SD card either by sideloading through CWM or by pushing it to the SD card through adb. The issue is that CWM gives me an error (can't mount SD card) and adb doesn't recognize my device (I have tried installing and reinstalling various drivers for the past few hours). I enabled USB Debugging mode before starting the process, but I am only able to get into Download and CWM modes right now (if I don't do the Download Mode or Recovery Mode key combination, I am stuck on the Galaxy S III screen). Am I bricked at this point, or is there a way to get VRALE6.bootloader.zip onto my phone and continue with the ROM process?
It is important to note that I formatted the SD card before starting this process because I wanted enough space to put the Cyanogenmod file on it. However, I think I may have formatted it generically rather than into FAT-32. Could this be the issue?
I am going to pick up a microSD card reader today in order to flash the SD card to FAT-32 and put the CyanogenMod file on it.
I am getting 5 errors upon startup of CWM (E: Can't mount /cache/recovery/command, can't mount /cache/recovery/log, etc.). When I try to mount the SD card or external SD card, I get E: Can't mount /sdcard/
Same issue with sd card not mounting.
I'm having somewhat of the same issue. I've tried both Clockwork recovery and TWRP and have the same issue.
Should have mentioned that i still have access to the stock rom and can use my phone just fine.
I some how got Clockwork mod recovery to work using the Rom Manager pro App.
I wish i had been paying better attention to what i was doing but i know i updated CWMrecovery from in rom manager and chose to install my chosen rom with that.
My suggestion is to start over completely. There is a much easier way to do this.
My suggestion is to flash one of the rooted stock ROMs through Odin. There's a thread in android development that has rooted stock. Then when that's done boot up your phone. If it bootloops wipe data. Then use Ez-Unlock 1.2 app to unlock your bootloader. Make sure it's 1.2. Now use GooManager to flash TWRP. You are done! This is probably the easiest way to do this.
Thread: http://forum.xda-developers.com/showthread.php?p=33948598
Sent from my SCH-I535 using Tapatalk
Sent from my SCH-I535 using Tapatalk
Sandman-007 said:
My suggestion is to start over completely. There is a much easier way to do this.
My suggestion is to flash one of the rooted stock ROMs through Odin. There's a thread in android development that has rooted stock. Then when that's done boot up your phone. If it bootloops wipe data. Then use Ez-Unlock 1.2 app to unlock your bootloader. Make sure it's 1.2. Now use GooManager to flash TWRP. You are done! This is probably the easiest way to do this.
Thread: http://forum.xda-developers.com/showthread.php?p=33948598
Sent from my SCH-I535 using Tapatalk
Sent from my SCH-I535 using Tapatalk
Click to expand...
Click to collapse
I am not familiar with TWRP, so is the process the same for flashing CM (putting CM zip file on sd card and going to install from SD card in TWRP)? Are there any additional steps beyond this?
I am following the directions in the thread linked above to root and install TWRP. So far, I have the rooted stock ROM running fine, but I can't get TWRP to work. I downloaded Goomanager and attempted to get TWRP using the Install Openrecovery Script option. However, it said that it couldn't find a recovery for my device. I also tried to use the adb method, but nothing happened after I put in the commands. I even tried to flash the latest TWRP .tar file from their website using Odin, but it keeps failing. Is there any way to get TWRP on my phone?
EDIT:Whoops, I skipped over the EZ-Unlock step. Now everything works. Thanks for the help, Sandman!
mikestrong19 said:
I am following the directions in the thread linked above to root and install TWRP. So far, I have the rooted stock ROM running fine, but I can't get TWRP to work. I downloaded Goomanager and attempted to get TWRP using the Install Openrecovery Script option. However, it said that it couldn't find a recovery for my device. I also tried to use the adb method, but nothing happened after I put in the commands. I even tried to flash the latest TWRP .tar file from their website using Odin, but it keeps failing. Is there any way to get TWRP on my phone?
EDIT:Whoops, I skipped over the EZ-Unlock step. Now everything works. Thanks for the help, Sandman!
Click to expand...
Click to collapse
No problem bro. Glad you are all fixed up
Sent from my SCH-I535 using Tapatalk
Sandman-007 said:
No problem bro. Glad you are all fixed up
Sent from my SCH-I535 using Tapatalk
Click to expand...
Click to collapse
Alright, maybe I'm not quite fixed up yet. I have TWRP installed and I can go between TWRP, download mode, and the normal stock rooted ROM fine. However, I cannot get to the SD Card in TWRP in order to install CM. TWRP gives me the following errors upon booting into recovery:
E: Unable to find parition size for '/boot'
E: Unable to find parition size for '/data'
E: Unable to find parition size for '/recovery'
Updating partition details:
E: Unable to mount '/system'
E: Unable to mount '/cache'
E: Unable to mount '/cache'
E: TWFunc: :Copy_Log - - Can't open destination log
E: Unable to mount '/cache'
Upon trying to go to Install, I am unable to select the external SD card, and an additional error appears when I attempt to touch Micro SD Card (E: Unable to mount '/external_sd').
I guess I could try to sideload the CM zip file through adb, but I would rather fix the SD card for future use. I have been researching and working on the SD card for the better part of today, to no avail. I am pretty sure the issue is in the formatting of the SD card (it appears to be RAW rather than the required FAT32 for CM), but I cannot format the SD card into FAT-32 no matter what I try (both Windows and 3rd party formatting tools). They all say that the SD card is either write-protected (I have already checked the read/write switch on the side of the SD card adapter) and/or the format cannot be completed. I have tried both my old SD card that I have kept for a few phones (an 8GB Samsung microSD card) and a brand new Sandisk 8GB microSD card, both of which will not work.
I am able to transfer files to the SD card with no issue (with both ADB and through dragging/dropping in Windows), but I cannot install from SD in recovery.
Does anyone have a solution to allow me to install CM on my phone?
Download root checker from the play store. Make sure you are rooted
Sent from my SCH-I535 using Tapatalk
Sandman-007 said:
Download root checker from the play store. Make sure you are rooted
Sent from my SCH-I535 using Tapatalk
Click to expand...
Click to collapse
Yes, I do have root access. I think the problem lies somewhere in my SD card.
mikestrong19 said:
Yes, I do have root access. I think the problem lies somewhere in my SD card.
Click to expand...
Click to collapse
Do you have another computer to try formatting the sdcard with? And you said that you receive the same errors when trying to reformat the new 8 GB sdcard as with your other sdcard which is formatted to RAW?
SlimSnoopOS said:
Do you have another computer to try formatting the sdcard with? And you said that you receive the same errors when trying to reformat the new 8 GB sdcard as with your other sdcard which is formatted to RAW?
Click to expand...
Click to collapse
I do have access to another computer, but I ran out of time and patience yesterday. I will try it when I get home later today. And yes, both cards are RAW (even the new one) and I can't get either one to format or work in TWRP.
So it appears the the issue with formatting was due to my computer's drivers (even though I installed the latest Samsung USB drivers) and not the SD card. I was able to format the SD card to FAT32 on another computer and put CM and GAPPS onto it. When booted normally into TouchWiz, the phone sees the SD card fine. However, I still get the same "Can't mount external SD card" error as well as the others previously listed when I attempt to install a zip from recovery. I even tried to sideload the ROM from ADB, but it still didn't work.
mikestrong19 said:
So it appears the the issue with formatting was due to my computer's drivers (even though I installed the latest Samsung USB drivers) and not the SD card. I was able to format the SD card to FAT32 on another computer and put CM and GAPPS onto it. When booted normally into TouchWiz, the phone sees the SD card fine. However, I still get the same "Can't mount external SD card" error as well as the others previously listed when I attempt to install a zip from recovery. I even tried to sideload the ROM from ADB, but it still didn't work.
Click to expand...
Click to collapse
Which version of CWM and also TWRP are you using?
And the problems keep rolling in. I was able to mount my SD card and get rid of the TWRP errors by installing a modded TWRP 2.6.0.0 from this thread (http://forum.xda-developers.com/showthread.php?p=44277901). However, when I go to install CM (cm-10.1.3-d2vzw.zip), I get the following error:
assert failed: getprop("ro.product.device") ==
E: Error executing updater binary in zip '/external_sd/cm-10.1.3-d2vzw.zip'
Error flashing zip '/external_sd/cm-10.1.3-d2vzw.zip'
Updating partition details
I did a factory reset before attempting to install this, but I did not format data or do anything else.
mikestrong19 said:
And the problems keep rolling in. I was able to mount my SD card and get rid of the TWRP errors by installing a modded TWRP 2.6.0.0 from this thread (http://forum.xda-developers.com/showthread.php?p=44277901). However, when I go to install CM (cm-10.1.3-d2vzw.zip), I get the following error:
assert failed: getprop("ro.product.device") ==
E: Error executing updater binary in zip '/external_sd/cm-10.1.3-d2vzw.zip'
Error flashing zip '/external_sd/cm-10.1.3-d2vzw.zip'
Updating partition details
I did a factory reset before attempting to install this, but I did not format data or do anything else.
Click to expand...
Click to collapse
Well, that is for the Sprint S3 my friend. We can't interchange recoveries between the different S3 models to flash roms. You may want to ask Kennyglass123 or any of those other guys if they can make a change for the VZW S3 for you to test it out.
SlimSnoopOS said:
Well, that is for the Sprint S3 my friend. We can't interchange recoveries between the different S3 models to flash roms. You may want to ask Kennyglass123 or any of those other guys if they can make a change for the VZW S3 for you to test it out.
Click to expand...
Click to collapse
Sounds good. I think the problem has been isolated to being something with needing a modded TWRP. I tried using an older, non-modded TWRP (2.5.0.0), which didn't work.
mikestrong19 said:
Sounds good. I think the problem has been isolated to being something with needing a modded TWRP. I tried using an older, non-modded TWRP (2.5.0.0), which didn't work.
Click to expand...
Click to collapse
Would you mind trying this soft brick fix? If I'm not mistaken, I believe you're experiencing this same issue--excluding the Sprint TWRP issue you just mentioned. You will need to flash your VZW custom recovery either through GooManager, Rom Manager, or Odin btw.
SlimSnoopOS said:
Would you mind trying this soft brick fix? If I'm not mistaken, I believe you're experiencing this same issue--excluding the Sprint TWRP issue you just mentioned. You will need to flash your VZW custom recovery either through GooManager, Rom Manager, or Odin btw.
Click to expand...
Click to collapse
I can still get between the stock rooted ROM, download mode, and recovery mode fine, so does that mean I am still soft-bricked and should try this?
mikestrong19 said:
I can still get between the stock rooted ROM, download mode, and recovery mode fine, so does that mean I am still soft-bricked and should try this?
Click to expand...
Click to collapse
Yea, because you are still receiving these errors right?
E: Unable to find parition size for '/boot'
E: Unable to find parition size for '/data'
E: Unable to find parition size for '/recovery'
Updating partition details:
E: Unable to mount '/system'
E: Unable to mount '/cache'
E: Unable to mount '/cache'
E: TWFunc: :Copy_Log - - Can't open destination log
E: Unable to mount '/cache'
Click to expand...
Click to collapse
This soft brick fix is an attempt to correct the /system and /data errors.
Edit: Oh great, none of the links work. I'll see about finding alternate links.
I am not new to ROM's I have dabbled here and there with my phones and the xoom. I followed the directions to a t for the Omni 4.4.2. I did the first part for putting bigPart TWRP on my xoom. I have the recovery on there and I can find my SD card with the rom and other files on there needed but it will not load after I install everything. The internal storage still shows at 0. I get the Omni bootloader and then a message from google pops up saying encryption unsuccessful and I need to perform a factory reset. When I try that it just brings me back to recovery. I don't know what I did wrong but the only thing that works is recovery. It's like nothing at all is on the internal storage of the xoom. I have tried to copy the files from my sd card over to internal and install, same thing. When I go back to check the files I copied to internal they are gone. The files I have on the sd card are there but it won't load the files on the internal storage to set up android on there. I can't even go back to an old restore cause I was using cwm recovery and the those restore files aren't recognized. I'm at a loss, any help would be greatly appreciated. I can't even get my computer to see so I can push the files over to it and I am pretty rusty with ADB to try and set that up.
I just tried to push the original twrp 2630 through adb and it flashed, I tried to reboot into recovery and it just staid at the twrp screen. Ughhh I'm getting so frustrated cause I had the xoom working perfectly on JB before I started messing around. Any help would be great, Even getting me back to stock and I can take it from there.
update
at0msplat said:
I am not new to ROM's I have dabbled here and there with my phones and the xoom. I followed the directions to a t for the Omni 4.4.2. I did the first part for putting bigPart TWRP on my xoom. I have the recovery on there and I can find my SD card with the rom and other files on there needed but it will not load after I install everything. The internal storage still shows at 0. I get the Omni bootloader and then a message from google pops up saying encryption unsuccessful and I need to perform a factory reset. When I try that it just brings me back to recovery. I don't know what I did wrong but the only thing that works is recovery. It's like nothing at all is on the internal storage of the xoom. I have tried to copy the files from my sd card over to internal and install, same thing. When I go back to check the files I copied to internal they are gone. The files I have on the sd card are there but it won't load the files on the internal storage to set up android on there. I can't even go back to an old restore cause I was using cwm recovery and the those restore files aren't recognized. I'm at a loss, any help would be greatly appreciated. I can't even get my computer to see so I can push the files over to it and I am pretty rusty with ADB to try and set that up.
I just tried to push the original twrp 2630 through adb and it flashed, I tried to reboot into recovery and it just staid at the twrp screen. Ughhh I'm getting so frustrated cause I had the xoom working perfectly on JB before I started messing around. Any help would be great, Even getting me back to stock and I can take it from there.
Click to expand...
Click to collapse
trying to give as much info as I can. I got the original twrp 2630 running, flash twrp big part, followed next step to to wipe everything except sdcard, this is what I got:
Updating partition details...
E:unable to mount '/system'
E:unable to mount '/cache'
E:failed to wipe dalvik
updating partition details...
E:unable to mount '/system'
E:unable to mount '/cache'