Database Info

[Q] Reason: No Kernal (Odin 3 downloading mode)

Today my Samsung galaxy R i9103 turned into brick..
My phone have been rooted following this thread: http://forum.xda-developers.com/showthread.php?t=1406880 for 5 months and worked well until today
I can't turn on my phone trying all the methods..like taking off the battery and putting it on, removing my SIM and microSD card, pressing volume-+home button+power button...
But the notebook recognizes it as APX when I plug it in
Later, I installed something like a NVIDIA driver
I have found a .bat on other forum, run it and can get into odin 3 download mode now
Under the title(Odin 3 download mode protocol v2), it writes
Reason: No Kernal
Check Signature: Check
Custom Binary Download: No (0 Counts)
Current Binary: Samsung Official
Waitting USB Cable...
and I don't have any other options even rebooting my phone as it just shows me the same page.
1. With this situation, can I simply flash the original ROM using Odin? (someone said it is likely to be a hardware problem but not a software one)
2. Will Samsung know that my phone is rooted and refuse to fix it if I sent it to them ?
3. If yes, will flashing to the original ROM before sending it to them work?
4. Is there any way that I can fix the phone without losing my data inside?
Thanks so much!!!

Your counter is '0' so I think Samsung shouldn't be able to tell you that it was rooted but if they as a policy don't accept handsets in APX mode then we can't be sure about what would be their response.
But did you try your luck with the following method ?
http://forum.xda-developers.com/showthread.php?t=1528256

'cooleagle' said:
Your counter is '0' so I think Samsung shouldn't be able to tell you that it was rooted but if they as a policy don't accept handsets in APX mode then we can't be sure about what would be their response.
But did you try your luck with the following method ?
http://forum.xda-developers.com/showthread.php?t=1528256
Click to expand...
Click to collapse
Just the same thing as what I have used
Do you know will I still have my data inside after I flash the original rom again?
And what about the counter, will it increase?
Anyway, thanks

1.Yes. You can Flash a stock ROM in the download mode.
2. If you flash a stock ROM, your download counter will not increase and Samsung will not know you played around with your device.
If you flash some insecure kernel (modified ROMs) via ODIN then counter will increase.
3. You dont have to flash if wanna send them to repair. You are very safe to send it to repair as it is.
4.What ROM version were u on before? Determine that first and try to flash the the boot kernel and see whether u can make it work?
If no luck you can flash a full ROM. You SDcard/usbstorage files will not be deleted. Only the system partition is going to be modified.
leon090807 said:
Today my Samsung galaxy R i9103 turned into brick..
My phone have been rooted following this thread: http://forum.xda-developers.com/showthread.php?t=1406880 for 5 months and worked well until today
I can't turn on my phone trying all the methods..like taking off the battery and putting it on, removing my SIM and microSD card, pressing volume-+home button+power button...
But the notebook recognizes it as APX when I plug it in
Later, I installed something like a NVIDIA driver
I have found a .bat on other forum, run it and can get into odin 3 download mode now
Under the title(Odin 3 download mode protocol v2), it writes
Reason: No Kernal
Check Signature: Check
Custom Binary Download: No (0 Counts)
Current Binary: Samsung Official
Waitting USB Cable...
and I don't have any other options even rebooting my phone as it just shows me the same page.
1. With this situation, can I simply flash the original ROM using Odin? (someone said it is likely to be a hardware problem but not a software one)
2. Will Samsung know that my phone is rooted and refuse to fix it if I sent it to them ?
3. If yes, will flashing to the original ROM before sending it to them work?
4. Is there any way that I can fix the phone without losing my data inside?
Thanks so much!!!
Click to expand...
Click to collapse

Thanks.
I flashed the stock ROM with re-partition and need to wipe all my data to get it working...
if not, it will stuck in a rebooting loop
Do you think it is likely to be caused by rooting?
Or it's a bug which will bring down the whole system?

leon090807 said:
Thanks.
I flashed the stock ROM with re-partition and need to wipe all my data to get it working...
if not, it will stuck in a rebooting loop
Do you think it is likely to be caused by rooting?
Or it's a bug which will bring down the whole system?
Click to expand...
Click to collapse
NOOOO... re-partition needs to be "UNCHECKED"... i.e. there shouldn't be any tick in the box of re-partition...

sagarwadhwa1 said:
NOOOO... re-partition needs to be "UNCHECKED"... i.e. there shouldn't be any tick in the box of re-partition...
Click to expand...
Click to collapse
there's a PIT doc and people on the internet says it needs to undergo re-partition or else there will be error

Did you re-partition you system? You can try the stock boot kernel if you dint repartition/ wipe.
leon090807 said:
Thanks.
I flashed the stock ROM with re-partition and need to wipe all my data to get it working...
if not, it will stuck in a rebooting loop
Do you think it is likely to be caused by rooting?
Or it's a bug which will bring down the whole system?
Click to expand...
Click to collapse

kies update bricked my aunts phone

I have already used kies once to upgrade my sgh-i727's firmware to ICS. Anyways my aunt asked if i would do hers for her. I ran kies but after the firmware install had started I got an error message asking me to unplug my phone and boot in to recovery mode. However I can only get the phone to boot into odin mode. Either by turning it on normally i get the error:
odin mode
product name: sgh-727
custom binary download: no
current binary: samsung official
firmware upgrade encountered an issue. please select recovery mode in kies & try again.
Or i can boot in to normal odin mode holding the volume up and down keys while plugging the usb port in. Then I choose volume up to load custom rom i end up at the same error.
I did try endlessly booting into recovery mode holding the volume up and down keys while powering on (also tried just up and just down to ensure i wasn't crazy) and while samsung flashes super briefly i again end up in odin mode with the error message. I tried flashing a stock ICS and gingerbread roms via odin 1.85 but it fails saying there is no pit file. I have searched for a pit file to load but have been unable to find one, in fact I noticed I was not the only one unable to locate one for this model phone.
Even without recovery mode I still did try to do a emergency firmware recovery in odin mode (rather sure it wouldn't work but what the heck) to no avail. I am at a total loss. Does anyone have any ideas how to fix this brick aside from haveing her exchange it with ATT? It is only two days old so that is a possibility if worse comes to worse.
I have scoured the forums, Google and everything else I could think of before asking for help so please don't thrash me if i missed something. some help and a point in the right direction is all i ask. thanks!

atomicWAR said:
I have already used kies once to upgrade my sgh-i727's firmware to ICS. Anyways my aunt asked if i would do hers for her. I ran kies but after the firmware install had started I got an error message asking me to unplug my phone and boot in to recovery mode. However I can only get the phone to boot into odin mode. Either by turning it on normally i get the error:
odin mode
product name: sgh-727
custom binary download: no
current binary: samsung official
firmware upgrade encountered an issue. please select recovery mode in kies & try again.
Or i can boot in to normal odin mode holding the volume up and down keys while plugging the usb port in. Then I choose volume up to load custom rom i end up at the same error.
I did try endlessly booting into recovery mode holding the volume up and down keys while powering on (also tried just up and just down to ensure i wasn't crazy) and while samsung flashes super briefly i again end up in odin mode with the error message. I tried flashing a stock ICS and gingerbread roms via odin 1.85 but it fails saying there is no pit file. I have searched for a pit file to load but have been unable to find one, in fact I noticed I was not the only one unable to locate one for this model phone.
Even without recovery mode I still did try to do a emergency firmware recovery in odin mode (rather sure it wouldn't work but what the heck) to no avail. I am at a total loss. Does anyone have any ideas how to fix this brick aside from haveing her exchange it with ATT? It is only two days old so that is a possibility if worse comes to worse.
I have scoured the forums, Google and everything else I could think of before asking for help so please don't thrash me if i missed something. some help and a point in the right direction is all i ask. thanks!
Click to expand...
Click to collapse
take the battery out, put it in download mode and use odin to just flash a stock 4.0.4 att rom
this has happened to me during a 2.3.6 upgrade and i switched usb ports, pulled battery and plugged back in and used odin to flash a stock 2.3.6
here is the stock att official 4.0.4 http://www.hotfile.com/dl/162779401/27c699c/I727UCLF6_I727ATTLF6_ATT.zip.html

just go to the first link in my sig

thanks my brain was hurting. had already pulled the battery etc but then i retried all my usb ports and that was the hang up for odin at least. you guys are awesome.

atomicwar said:
thanks my brain was hurting. Had already pulled the battery etc but then i retried all my usb ports and that was the hang up for odin at least. You guys are awesome.
Click to expand...
Click to collapse
good to hear

Problem solved?
CM9 Skyrocket

vincom said:
just go to the first link in my sig
Click to expand...
Click to collapse
Dude, I think I just saved my phone. I was freaking out, you have no idea. Thank you so very, very, very much. I'm truly grateful to you!
Seriously, thanks. =]

Thank YOU
vincom said:
just go to the first link in my sig
Click to expand...
Click to collapse
New to the boards; however, I must say THANK YOU to the persons who own and operate these boards. Also a BIG THANK YOU to vincom and everyone else who helps on these boards.
I just went through the exact same dilemma that the person who created this post did. I thought for sure Kies ruined my phone.
Well I used vincom's resolution and my phone is working again AND I have ICS! Thank you!

Those who are saying thanks should click thanks on Vincom's post as well. Sending one his way for you...lol.
Sent from my SGH-I727 using xda app-developers app

[Q] Problem during rooting help

I was attempting to get root access to my galaxy tab 2 10.1 running android 10.2.1 (or whatever the latest Samsung update was it is 10.2 on my phone but am sure it was 10.2.1 on the tablet.
I was following this guide that someone here recommended
http://www.ibtimes.co.uk/articles/4...-p5113-android41-jellybean-android404-ics.htm
I set usb debug and made sure the drivers were on my pc and made sure KIES was completely not running
Followed the instructions to the letter but should have worried when I found the instructions to get to download were wrong - I found on videos that it was reboot using power and right volume key. That was successful
It connected to ODIN fine and the yellow box came up
I made sure the two boxes were ticked and then searched for the file
CF-Auto-Root-espresso10wifi-espresso10wifibby-gtp5113.zip and started ODIN
it seemed to be going fine until suddenly a red box came up with update failed
Now all I can get on the device is "firmware upgrade encountered an issue. Please select recovery mode in Kies and try again"
No matter how I try to restart this I get the same screen and imagine I couldn't connect to kies even if I should
Can anyone help as I am worried that I have bricked my device - I was looking for a simple way to get root without flashing a whole rom - or is that what I was doing anyway?

Here is a link that may can help you : http://forum.xda-developers.com/showthread.php?t=1722745
Try to do the point A to install CWM Recovery and root correctly the tab then do the point E to install the stock Android 4.0.4
ps : if you want to do something to your tab, try to search here before other websites, big community, good informations/tips (personnal advise) :good:

Maybe file you downloaded is corrupted , redownload it from xda or sammobile and do steps again

n0is said:
Here is a link that may can help you : http://forum.xda-developers.com/showthread.php?t=1722745
Try to do the point A to install CWM Recovery and root correctly the tab then do the point E to install the stock Android 4.0.4
ps : if you want to do something to your tab, try to search here before other websites, big community, good informations/tips (personnal advise) :good:
Click to expand...
Click to collapse
I will take a look but so far the only thing I get is the message to connect to KIES and it wont of course connect - cant get into any other modes - you would think they would have some kind of hard boot recovery button that gets you to basic screen to download the latest firmware.
And I did start here and believe that this led from a post here - I was trying to find the least complicated method of getting root access without changing what I already had too much - the only other process that I found on here seemed to have lots of people reporting problems if it wasn't a 3g model
It is beginning to look like I may have found out what bricking is - thanks for the reply anyway

would like to do that
mjrshark said:
Maybe file you downloaded is corrupted , redownload it from xda or sammobile and do steps again
Click to expand...
Click to collapse
In fact the instructions do say if it doesn't work first time, to run it again with the boxes unticked - the problem is that I cant get back to download mode, or any mode other than the message to connect to kies, so have no way of doing this. So looks like it may have bricked - is there any way of unbricking a tablet?:crying:
It's going to be an expensive mistake especially as I haven't even had the £50 cash back from Samsung yet and I would have to pay full price now to replace it,

So did you remove it from Odin after it failed?
If you connect and pull up Odin, even though its not in download mode, do you get an active com box showing its connected?
Have you tried kies yet?
There is a simple method of rooting in the link posted in the previous post by n0is. At this point you might have to flash a stock image before you try and root again. If you can get an active com port in Odin, run a stock image first, they can be found here in xda. Get it booted up and then make sure you are on the latest android version, its 4.1.1 here in the US. If you try and root first and then update, you will lose root so update first to avoid rooting twice.
Just to clarify the root procedures,
Odin the cwm recovery .tar from the thread.
Reboot to recovery then flash the super user zip for the p5113. It will ask you about erasing stock recovery or something like that, check yes.
And that's it, simple enough
Sent from my SCH-I535 using xda premium

not optamistic but will try!
samsgun357 said:
So did you remove it from Odin after it failed?
If you connect and pull up Odin, even though its not in download mode, do you get an active com box showing its connected?
Have you tried kies yet?
There is a simple method of rooting in the link posted in the previous post by n0is. At this point you might have to flash a stock image before you try and root again. If you can get an active com port in Odin, run a stock image first, they can be found here in xda. Get it booted up and then make sure you are on the latest android version, its 4.1.1 here in the US. If you try and root first and then update, you will lose root so update first to avoid rooting twice.
Just to clarify the root procedures,
Odin the cwm recovery .tar from the thread.
Reboot to recovery then flash the super user zip for the p5113. It will ask you about erasing stock recovery or something like that, check yes.
And that's it, simple enough
Sent from my SCH-I535 using xda premium
Click to expand...
Click to collapse
I will try but I don't think it is going to work. Whenever I connect the tablet by USB I get the usb connecting sound followed immediately by the USB disconnect sound - this just continues to happen every 4 seconds or so all the time that the device is connected. At the moment I have it on charge as once the error screen comes on it doesnt seem to go off for a very long time and then it wont start unless I charge it first. After a few minutes on charge - The firmware upgrade encountered an issue message comes up. I am going to leave it a while until I am sure it is fully charged and then try what you suggest - not optamistic though since I now realise that it is not even connecting properly. I just have a bad feeling about this. I had to disconnect it from the power yesterday because the error screen stays on continuously and the device starts to get warm
Assuming that I ever manage to get a stock image installed will this mean I can go back to normal kies updates - all I really wanted was the standard samsung android O/S but with super user added.
Unfortunately I had read the linked article a while back and what made me more confident was the statement that said it was "virtually impossible to brick this device"

Since it's still going into Charging mode and spitting out error messages, it's not completely bricked. It's just in a reboot loop (a.k.a. soft brick).
Keep trying to get it into Download mode. Sometimes the timing is a little tricky if it's in a boot loop.
1. Disconnect it before trying to get it into Download Mode. If it's plugged in (charger or PC), the device will go into Charging mode instead.
2. Hold the Power button for 10 seconds to make it reboot.
3. When you see the screen turn off, let go of Power and then press and hold Power and Volume Right/Up.
4. If done correctly, it will immediately go into Download Mode. If you see the Samsung logo instead, repeat from Step 2.

some progress but still stuck - any more ideas please
samsgun357 said:
So did you remove it from Odin after it failed?
If you connect and pull up Odin, even though its not in download mode, do you get an active com box showing its connected?
Have you tried kies yet?
There is a simple method of rooting in the link posted in the previous post by n0is. At this point you might have to flash a stock image before you try and root again. If you can get an active com port in Odin, run a stock image first, they can be found here in xda. Get it booted up and then make sure you are on the latest android version, its 4.1.1 here in the US. If you try and root first and then update, you will lose root so update first to avoid rooting twice.
Just to clarify the root procedures,
Odin the cwm recovery .tar from the thread.
Reboot to recovery then flash the super user zip for the p5113. It will ask you about erasing stock recovery or something like that, check yes.
And that's it, simple enough
Sent from my SCH-I535 using xda premium
Click to expand...
Click to collapse
Hi well thanks -
when I connected Odin it did show up yellow and so I downloaded the P5110 stock from from the other thread - all went well and it reported all OK and re-booted - saw the animated sequence but now it has stalled on the samsung logo and still wont connect to kies
So still stuck but at least it has moved on - The instructions on the other page were a little unclear about one stage
It said if there was pit file included to set something and tick repartition - this was all in one line and so I assumed part of the pit instruction - as there was no pit file I did not tick re-partition - I wonder if I should have done?
I have just reconnected to ODIN and the ID Com is still lit up yellow so presumably I could try running it again, or should I look on here for another stock rom - I am wondering if I have somehpw scewed up the bootloader and if so how I go about restoring it
ODIN is the only thing it connects to right now

No download mode, no recovery, detected by odin, not kies

Hi,
I rooted my brandnew GT-P3110 with cf, flashed pacman and cwm recovery. I do not blame anybody alse for my issues but myself. I guess I messed up the restoring of NON-system-apps:
After a day of troublefree use the tablet randomly rebooted and came back with the message "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again.". No booting into recovery possible, no booting into download mode, no regular boot. Just the same message over and over again. Battery is unremovable.
I installed Kies, updated it, it downloaded drivers but under "emergency recovery" my tablet didn't appear. I then followed the "Firmware Upgrade and Initialization" procedure wich downloaded the necessary files but aborted with a korean text shown in the attachment after replugging the tablet. I tried this with 2 different USB-cables on several USB-ports. Kies btw asked me to remove the battery (not possible) after entering device number and serial-number. I turned off by pressing the off button instead and it turned on again.
I uninstalled Kies, rebooted, installed the samsung drivers manually, rebooted. I installed odin 1.85 (and later 1.3) and downloaded my contry's stock firmware (and later a newer version of the same firmware and another country's stock) from sammobile. I tried to flash them first without "repartition" ticked, later with it ticked but without a pit file (i can't find it!). I got four different errors, two are attached, the third was somethign like "cant write (line 1876)" and "cant write (line 1440)".I tried three stock firmwares with two version of odin with two USB cords on everal ports on ONE computer. I remove the tablet every time, exited odin every time, run it as admin, disabled firewall, xp-antispy and antivirus. I'm on Windows 7.
Besides a million other threads I found this one, but I wasn't able to solve my issue with it: http://forum.xda-developers.com/showthread.php?t=1652398
For 48 hours i tried to solve this problem by myself. Now I hope to find out if there's a point in continuing or if I can give up and throw away the piece of samsung.
Cheers,
404

android404 said:
Hi,
I rooted my brandnew GT-P3110
404
Click to expand...
Click to collapse
Try odin 1.61 1.85 sometimes itll jar it loose

vizionforever said:
Try odin 1.61 1.85 sometimes itll jar it loose
Click to expand...
Click to collapse
I am having the same problem with a P5113. Started with stuck at the Samsung logo. Then I tried a flash from Odin that didn't work. That led to the "Firmware error" screen telling me to use Keis. Keis fails to find the tablet. Odin still sees it but doesn't get a good write.
Now all I get is the battery icon when plugged in but that's it.
Things I have tried:
1) Two versions of Odin
2) Different USB ports
3) Different PC
I also let the device sit over the weekend to completely discharge. Still nothing.
Did you (or anyone else) resolve this issue?

vizionforever said:
Try odin 1.61 1.85 sometimes itll jar it loose
Click to expand...
Click to collapse
Thanks but it didn't work.
wd5gnr said:
I am having the same problem with a P5113. Started with stuck at the Samsung logo. Then I tried a flash from Odin that didn't work. That led to the "Firmware error" screen telling me to use Keis. Keis fails to find the tablet. Odin still sees it but doesn't get a good write.
Now all I get is the battery icon when plugged in but that's it.
Things I have tried:
1) Two versions of Odin
2) Different USB ports
3) Different PC
I also let the device sit over the weekend to completely discharge. Still nothing.
Did you (or anyone else) resolve this issue?
Click to expand...
Click to collapse
Mine is still bricked. Good luck.

facing same problem in my samsung tab 2 p3100 after root

wd5gnr said:
I am having the same problem with a P5113. Started with stuck at the Samsung logo. Then I tried a flash from Odin that didn't work. That led to the "Firmware error" screen telling me to use Keis. Keis fails to find the tablet. Odin still sees it but doesn't get a good write.
Now all I get is the battery icon when plugged in but that's it.
Things I have tried:
1) Two versions of Odin
2) Different USB ports
3) Different PC
I also let the device sit over the weekend to completely discharge. Still nothing.
Did you (or anyone else) resolve this issue?
Click to expand...
Click to collapse
Dude had the same issue on my galaxy S2 and resolved it. I downloaded the
The .pit file for my gt-i9100g (http://data.hu/get/4697903/omap4_all_20110627_emmc.pit)
The stock ROM from sammobile. (http://www.sammobile.com/firmwares/2/)
The JB Bootloader
The stock JB kernel.
Opened odin v1.85.
Then i used the vol down+home+lock keys together to try to open the download mode ( but ended up in the "Firmware error " page) and connected phone to the pc. It shows "Added!" in the message box.
Repartition with the .pit and it will reboot.
Disconnect
Get into download mode and install the bootloader and it should reboot when done. Disconnect.
Get into download mode and connect
Installed the kernel through odin and reboot
Download mode again and install the ROM through odin.
If the phone gets stuck in boot loop (samsung logo over and over),
get into recovery mode ( for s2, vol up+home+lock, it needs to be pressed intermittently)
Then do a full format along with wipe cache.
And then the phone finally booted completely. :laugh: . Good Luck.
Note: I'm not sure to boot into recovery and download are the same key combos as it was for the i9100g.

novjean said:
Dude had the same issue on my galaxy S2 and resolved it. I downloaded the
The .pit file for my gt-i9100g (http://data.hu/get/4697903/omap4_all_20110627_emmc.pit)
Click to expand...
Click to collapse
Thanks. Well, I understand the theory. I have had trouble finding a PIT file that I am sure is for my device. I did save a PIT file but I think it is corrupt because using it requires me to let the battery die afterwards to get back to download mode. Same for the bootloader. I have a few things I've tried, but not sure I have one that is exactly for the GT-P5113 (in fact, I never did find a JB for the 5113 just the 5110 and it never would load).

Well no amount of coaxing has put life back into the tab
I may try again out of curiosity, but rather than invest more time I went out and bought a 32G Nexus 7 (2013 version). I would still like to get the Galaxy Tab alive again -- it has corrupted the flash twice before and each time I was able to bring it back to life. Not sure if this is an actual hardware failure or if it is just beyond partitioning.
I have a feeling if I had the right PIT and the right bootloader I could get back in business.

I can do each thing you mentioned, but my device is not getting detected by my PC. When I insert USB it says USB not recognized and it is not detected by Odin, adb and anything else. I am stuck on Boot Logo for my P3100 and when I go into recovery, it says USB not recognized. Fully messed up. Can you help me out here.
novjean said:
Dude had the same issue on my galaxy S2 and resolved it. I downloaded the
The .pit file for my gt-i9100g (http://data.hu/get/4697903/omap4_all_20110627_emmc.pit)
The stock ROM from sammobile. (http://www.sammobile.com/firmwares/2/)
The JB Bootloader
The stock JB kernel.
Opened odin v1.85.
Then i used the vol down+home+lock keys together to try to open the download mode ( but ended up in the "Firmware error " page) and connected phone to the pc. It shows "Added!" in the message box.
Repartition with the .pit and it will reboot.
Disconnect
Get into download mode and install the bootloader and it should reboot when done. Disconnect.
Get into download mode and connect
Installed the kernel through odin and reboot
Download mode again and install the ROM through odin.
If the phone gets stuck in boot loop (samsung logo over and over),
get into recovery mode ( for s2, vol up+home+lock, it needs to be pressed intermittently)
Then do a full format along with wipe cache.
And then the phone finally booted completely. :laugh: . Good Luck.
Note: I'm not sure to boot into recovery and download are the same key combos as it was for the i9100g.
Click to expand...
Click to collapse

2 years later .... did you ever unbrick this? I'm dealing with a P5113 now that's stuck at the "Firmware upgrade encountered an issue" screen. <sigh>
wd5gnr said:
Well no amount of coaxing has put life back into the tab
I may try again out of curiosity, but rather than invest more time I went out and bought a 32G Nexus 7 (2013 version). I would still like to get the Galaxy Tab alive again -- it has corrupted the flash twice before and each time I was able to bring it back to life. Not sure if this is an actual hardware failure or if it is just beyond partitioning.
I have a feeling if I had the right PIT and the right bootloader I could get back in business.
Click to expand...
Click to collapse

No. I finally sent it to one of these ebay guys who will JTAG it since I was too lazy to wire up one of my JTAG probes. They worked on it and said it was simply dead and the only alternative would be to replace the flash chips.
Bought a Nexus 7.

I've got the pit files for P311x and P3100 on my website https://sites.google.com/site/jrc2swebsite/downloads/samsung-galaxy-tab-2-70-p31xx

[Q] Bricked Tablet - see post for details

Here is the sequence of events:
Galaxy tab 2 10.1 with factory rom (wife's tablet)
Wife tells me that she keeps trying to complete the update everytime she gets prompted, but it always fails
Wife also tells me that she can't power off the tablet (she presses the power button, it shuts down, but then it starts up again)
I try the upgrade, get same result as wife
I try to reset the rom: I download what I think is the correct file, download Odin 1.85, and run it.
put tablet into download mode, attempt to use Odin to load new rom ***note, this is probably where I screwed up, as I am not sure i used the correct file. This is the file I used: PDA_HC31_EG01Ba_AP352081user_CP1033580_LTE20110704_0708.tar, which I found in a search on xda forums for my problem.
Odin reported failure. I tried again, same result.
I tried using KIES, using the Firmware upgrade and intitialisation (note that I must have UK version of KIEs, based on the spelling of initialisation--maybe that's a problem??/). I put in the model number, then the serial number if the tablet, get a message that GT-P5113 does not support initializing
tablet displays the message: Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again.
I try to put tablet back into download mode, but that doesn't work. Any suggestions on what to do at this point? Appreciate a step-by-step solution, if possible.
Thanks!

kevinkohut said:
Here is the sequence of events:
Galaxy tab 2 10.1 with factory rom (wife's tablet)
Wife tells me that she keeps trying to complete the update everytime she gets prompted, but it always fails
Wife also tells me that she can't power off the tablet (she presses the power button, it shuts down, but then it starts up again)
I try the upgrade, get same result as wife
I try to reset the rom: I download what I think is the correct file, download Odin 1.85, and run it.
put tablet into download mode, attempt to use Odin to load new rom ***note, this is probably where I screwed up, as I am not sure i used the correct file. This is the file I used: PDA_HC31_EG01Ba_AP352081user_CP1033580_LTE20110704_0708.tar, which I found in a search on xda forums for my problem.
Odin reported failure. I tried again, same result.
I tried using KIES, using the Firmware upgrade and intitialisation (note that I must have UK version of KIEs, based on the spelling of initialisation--maybe that's a problem??/). I put in the model number, then the serial number if the tablet, get a message that GT-P5113 does not support initializing
tablet displays the message: Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again.
I try to put tablet back into download mode, but that doesn't work. Any suggestions on what to do at this point? Appreciate a step-by-step solution, if possible.
Thanks!
Click to expand...
Click to collapse
Seems you flashed a wrong file.
Download another rom from http://live.samsung-updates.com/
and reflash with odin
Last week i tried to update my tab from 4.1.2 to 4.2.2 it hangup while flashing. Had to reset but then end up with firmware upgrade encountered blablabla. I just reflash within the blind screen without download mode and got it to work again

But don't I need to get the tablet into download mode first?
Rosli59564 said:
Seems you flashed a wrong file.
Download another rom from <<url.....>>
and reflash with odin
Click to expand...
Click to collapse
That makes sense, but how do I get the correct file to the tablet if I can't get the tablet into download mode?

kevinkohut said:
That makes sense, but how do I get the correct file to the tablet if I can't get the tablet into download mode?
Click to expand...
Click to collapse
If it's really a gt-p5113 then find the 1 for your country. If you're not sure your region code/csc then just download for any region.
You will know what i'm talking about if take a look at the given link

Please look at item 10 on my list
Rosli59564 said:
If it's really a gt-p5113 then find the 1 for your country. If you're not sure your region code/csc then just download for any region.
You will know what i'm talking about if take a look at the given link
Click to expand...
Click to collapse
I can't load ANY file to the tablet, as I CANNOT GET IT INTO DOWNLOAD MODE. I need to know how to force the tablet into download mode. Pressing POWER and VOLUME DOWN does not work. NOTHING HAPPENS.

Connect to PC on the screen "firmware upgrade encountered blablabl" Downloadmode on in Background, Odin can get access
If you are working with Odin, please kil ALL Samsung and KIES Programs and Services running in Background.

Hi for go to download mode you have to press power and volume up buttons
Sent from my GT-P5113 using XDA Premium 4 mobile app

Android-Andi said:
Connect to PC on the screen "firmware upgrade encountered blablabl" Downloadmode on in Background, Odin can get access
If you are working with Odin, please kil ALL Samsung and KIES Programs and Services running in Background.
Click to expand...
Click to collapse
I have tried this many times and Odin just fails. TWRP, CWM, Phil's touch all tried and failed. I have tried so many ROMs not sure I could list 'em all. Wanted to try SlimKat. But have this same problem, can't find the handle now, I only get the firmware upgrade encountered blah, blah. I'm just about ready to make confetti out of it! Can I get assistance with this problem, please. I don't care what ROM I have to run, I just need it to work...

Any solution to your problem?
Pp.

PanchoPlanet said:
Any solution to your problem?
Pp.
Click to expand...
Click to collapse
None as yet, I'm running out of real estate to search...

The rom you used in your op was probably for a data tab like sprint, att, Verizon, that is usually a brick result.
If you could factory reset you may have a chance but I doubt it without recovery or download mode.
Pp

You are faceing the "black screen of death" ("Firmware upgrade encountered an issue....").
Uninstall kies and reboot your pc.
Start odin.
Connect the tab running the black screen of death (BSOD).
Download mode running in background of BSOD so odin will detect your device.
Flash the correct firmware now and pray flashing the at&t rom didn't caused a hardbrick.
Send from OnePlus One using Tapatalk

Correct rom
I think that is exactly my problem. Last night I got Odin to run all the way through, it said pass but still no soap. I'm just about to list it for parts and at least minimize my loss.