I have an HTC Explorer, which came with a USB cable and an adapter to allow me to charge via mains as well. (Something like this: http://i.expansys.com/i/g/g232723.jpg - that's not the exact same one, but you get the idea). This charger says on it that it has an output of 5V and 1A. I also have a Blackberry Playbook, which came with a charger with a micro USB connector. However, this charger says on it that it has an output of 5V and 2A.
I have tested the HTC charger with my playbook, and it worked, but the question I want to ask is this: would it be dangerous to try the playbook charger on my HTC phone? (2A output from Playbook charger versus the presumably expected 1A input on the phone) I would like to be able to only carry one charger when travelling and the playbook charger has interchangeable adapters for international plugs, so it would be better to take, but obviously I don't want to overload the phone and have it burst into flames or whatever.
Any advice on the matter would be great, thanks.
It's not recommended by the manufacturer. It can void your warranty, though I don't know how they'd ever find out you were doing so. There can also be issues when using the cable to transfer data and such.
I did watch a video about that Blackberry charger.
Supposedly because of that 2A output, it charges your phone twice as a fast.
Sent from my Ainol Novo7 Elf using xda premium
I don't think there would be considerable damages but..I'd just use them both, even if it's less comfortable
I looked around and I think it should be safe. From what I've read online, the phone will only take a certain amount of current, regardless of the current being made available by the charger. Because the voltage is the same (5V), and the resistance of the phone circuitry is constant, by Ohm's law, I = V/R, so I will always be the same as long as V is the same. Presumably it'll drop with a lower input current, but the max I will always be the same, and that'll be limited to a safe level.
It might take a slightly higher current (say if the max the phone can take is 1.2A or something, the 1A charger can only give 1A but the 2A would give the full 1.2A), but no higher than the circuits in the phone will allow. After reading this, I realised that it made a lot of sense, and I think it's right. I also read that if it does charge the phone faster (which it will if the phone is taking a higher current e.g. 1.2A) it'll reduce the number of charging cycles that you get out of the battery. But the consensus seems to be that doing it every now and again when travelling etc. should be fine.
Thanks for all your responses.
EDIT: I think at worst, I might damage the battery, and they're not overly expensive to replace I don't think.
I agree, the rating on the charger is what it's MAX output, not that it will push that much current to your device. If you have an extra USB cable (that you dont mind cutting apart) and a mulit-meter, you can check to see how much current your phone is pulling from the BB Playbook charger. connect your mult-meter in-line with the red wire in the usb cable (just connect all others together)
Just make sure your mult-meter is rated for at least 2A.
Hope this helps.
Devices with lithium batteries usually have a charger circuit that limit the peak current that is sent to the battery. They also utilize temperature compensation so if you are charging the battery too fast, it starts limiting the charge current.
Where you might have a problem is when it's plugged in and you are using it, especially if the battery is low. You get high charge currents, combined with the operating current.
Related
Hi guys,
since the charger of the iPhone has an USB connector, my question is if I can use that charger for the Nexus One too??
Since it supplies actually the same energy level (both can get energy from a PC USB instead), does this mean that also the charger delivers current with good specifications for the N1?
thanx in advance
exelero
How are you going to plug the iPhone 30 pin in to a micro USB? Maybe I'm not understanding you correctly.
to plug the microUSB-to-USB cable of the Nexus One into the USB socket of the iPhone charger.
moto1907 said:
How are you going to plug the iPhone 30 pin in to a micro USB? Maybe I'm not understanding you correctly.
Click to expand...
Click to collapse
I think (s)he means the mains adapter part with the USB socket in it - in which case yes it will work, you just need the right cable - which came with your N1
Looking forward to when all manufacturers standardised on micro usb, for a while I thought that mini usb was micro, so I was surprised to see that the n1 was different then I found out....
ok, now i see. Not enough coffee yet,lol
scote said:
in which case yes it will work
Click to expand...
Click to collapse
yeah, from the connection part, I know it will work. my question was more related if the iPhone charger delivers the appropriate current (tension/amperage) conditions for the N1 and, let's say, it won't burn the N1 due to a too high voltage, or mess up the battery due to an incorrect tension input.
I was just having a conversation on chargers with a friend of mine the other day and googled around on the subject on amperage/current/Ma of chargers..
I stumbled upon these posts (either here on XDA, Androidforums or other forums):
1. "The current rating on a voltage source is the maximum amount that the power
source can deliver without exceeding its saftey rating.
What this means is that if you are using some device that has a power supply
with a current rating of 500mA then its best not to use a different power
supply(at the same votlage rating) with a lower max current rating. i.e.,
anything < 500mA. Now ofcourse you might be able to get away with it but if
it burns down your house then its your fault.
A device will only pull the amount of current that it uses(assuming it is a
voltage controlled device) and this is true regardless of the current
rating(hence the saftey issues I discussed above). If a device
says(sometimes they don't) it uses 500mA then it uses 500mA. Maybe it
doesn't use 500mA all the time but the engineers have put that rating there
for a reason. Using any power supply with the right voltage and a current
rating of anything more than what the device uses is ok because the device
will only pull the current it uses.
Now, about the voltage rating: The voltage rating does not have to be exact
and different devices can tolerate different voltage ratings. The problem
usually is one of current. By increasing the voltage, say, you increase the
current the device uses and then you have changed the parameters that the
device was created with."
2. "And as far plugging your phone into a charger that outputs well over 850mA, don't worry about that either. Unlike voltage, the more amperage the merrier because the device will only take what it needs of the available resources."
3. "Moral of the story. Match the Voltage (5.1Volts) Meet or Exceed the 850mA rating. (which is .850 Amps) and you'll be fine."
4. "amps are not pushed but drawn
amps is the max the charger can provide
before it get pressured and lover the volts
you could use a 5volt 10000MegaAmp charger
and the device would only draw the amps the device
was made to draw all the rest of the amps would stay
at your electricity company
ohms law state Amps == volts / residence"
5. "amps are not pushed but drawn
ohms law state Amps == volts / residence
In other English:
P = VI, where
P = Power of device (watts) and is fixed
V = Voltage used by device (volts) and is fixed
I = Current (amps) and is decided by P/V (a fixed ratio)
So the device cannot draw more current than the fixed ratio. It may draw less current if the charger cannot supply the highest amount, but then as in one of the above posts, it simply takes longer to recharge.
With these devices, milliWatts/miliAmps are the scale, 5V is generally the fixed Potential Difference.
Used in a vehicle, the device is generally both drawing and expending energy (ie. charging and running say, GPS) simultaneously. This in/out situation when prolonged is the cause of the observed overheating with the original X1 battery."
Click to expand...
Click to collapse
Bottom line... Make sure the voltage is 5V, the amperage doesn't really matter.
thanx for your feedback.
both chargers have the same output (5V, 1A) - so I am already successfully using it.
blackberry storm also has micro-usb
hello two chargers and an extra usb-cable
To answer the OP's question...
yes it works fine. I have one in my car and charge my ipod and nexus at the same time without issue. The advanced zune car adapter also works (in case one of the 5 who own a zune are reading this ).
I have been using my old Iphone white plug -> USB adapter for almost a month now and I haven't had any issues.
I tried using the iPhone charger but it charges slow...it does not quick charge. Am I doing something wrong?
uhohhotdog said:
I tried using the iPhone charger but it charges slow...it does not quick charge. Am I doing something wrong?
Click to expand...
Click to collapse
no. If i'm up to date, and i think i am, you'll only get the 'fast charge' if you use the charger that came with your phone. the usb to usb micro chargers all charge slow
Can i use X10 mini charger (5v DC 850mA output) on nexus one by the things i read i understand that i can't but my english is not very good. Thanks
if youre talking about using the iphone usb cable on your n1, HAHAAHHAAHAHAHAH
if you mean using the usb-to-AC adaptor then yea you can use any usb cable to charge anything pretty much..
I have older chargers for that output 5.0v / 550mA and have noticed that the Captivate outputs 5.0v / 700mA.
1. Can I safely use the older, 550mA chargers with the Captivate and what will the effect be?
2. Can I safely use the Captivate's 700mA charger with the older phones and what will the effect be?
Thanks.
1. Yes, you can use it. But it will charge slower.
2. Yes, you can use it. I believe that just because the charger output is higher amperage doesn't mean that it will affect the phone adversely. Think of it this way: A lamp is plugged into the wall outlet at your house. That outlet is rated at 120v 15A. The bulb isn't using all 15 amps, so no problem. But if you were to turn the voltage up or down, the lamp will get brighter or dimmer respectively.
The Captivate can take up to a 1A (1000 mA) charger.
Truceda said:
1. Yes, you can use it. But it will charge slower.
2. Yes, you can use it. I believe that just because the charger output is higher amperage doesn't mean that it will affect the phone adversely. Think of it this way: A lamp is plugged into the wall outlet at your house. That outlet is rated at 120v 15A. The bulb isn't using all 15 amps, so no problem. But if you were to turn the voltage up or down, the lamp will get brighter or dimmer respectively.
The Captivate can take up to a 1A (1000 mA) charger.
Click to expand...
Click to collapse
Another question. You sound smart on this so how about using the nexus one car charger on this? Fits perfect and I don't see why not, but still Leary. .. what do you think?
As long as it puts out 5v, (which is USB standard), you are fine. The amperage is only relevant if the device REQUIRES it. For instance if the device draws 1A and your charger could only handle 550mA your device will charge very slowly.
On the other hand if your charger can handle 1.2A and your device only draws 700mA, then your charger will only output 700mA.
The important thing is the voltage, it needs to be 5v +/- 3% ...
I actually use a generic car charger I bought at walmart with 2 USB ports on it, and it works well for every USB powered device I own ... ZUNE, iPOD, phones etc.
OK. Thanks for the reply. I had read that a phone requiring 700mA that uses a 550mA charger could damage the charger and possibly the phone. That's what made me wonder. And that's what led to the question.
Let's make this a bit more interesting. There's a local, highly-reputable cell phone repair store that has stopped selling car chargers because, they say, the rapid charge is not good for the phone's battery. Their recommendation is to use an inverter (no, they don't sell them) so that you can then plug a standard wall charger into it or a USB cable if the inverter is so equipped. The AC current that results from utilizing the inverter is more consistent than the current flowing from a car charger. So...I purchased an inverter for less than $20 and use it to charge the Captivate in my car.
OK ... not sure we need to get this far down in the weeds on this but here goes ....
The USB2 standard for power distribution is 5v and the thresholds are 4.4-5.25V.
Power is supplied in units of 5v power ... 1 unit is 5v at 100mA, no device can draw more than 5 units from any one port. If you have ever seen a portable hard drive with 2 USB connectors it is because it requires more than 500mA to operate and by using 2 ports the device can draw up to 1A. For dedicated chargers the 4.4-5.25v still applies but shorting the D+/- and disabling the data connection allows the device to detect that it is connected to a dedicated charging port and draw a maximum of 1.8A.
In keeping with the above guidelines, when connected to your computer the Captivate can draw no more than 1 unit of power which is [email protected], when connected to a dedicated charger the phone can draw [email protected] and stay within the standard. (yes, it caps itself at 1A, I know).
OK ... the next bit is going to be hard to digest because there are plenty of examples to the contrary ... there is a standard for mobile USB chargers, and it requires wiring them as dedicated charging ports. What this means to us is that, in theory anyway, a mobile USB charger should allow a device to draw up to 1.8A from it (highly unlikely ... but that's the standard as written).
Here is the problem, if the device is plugged into a dedicated charging port and tries to draw it's maximum rated current, that amount of current may not always be available or it may fluctuate. This fluctuation is what causes problems. Have you ever turned you car stereo up real loud and seen your headlights dim in beat with the music? Same thing, the power system is being drawn down. There are a couple of ways to stabalize your power system ... install a large capacitor (mine is 2 Farad) to provide "conditioning", or go the transformer route.A tansformer provides conditioning, but only on its own outputs... while a large cap will condition the entire power system if installed correctly.
So yes, using a quick charger on your phone can cause issues if your car has a ****ty power system or a large stereo system which is not set up properly (again, ****ty power system). Make sure your charging device is within the standard, and you should be fine wether it is USB via a cigarette lighter port or a 110V transformer.
I appreciate your detailed, helpful reply.
Other than the important 5v parameter, what I've taken away from your information is that a car charger can be used in a vehicle with a power supply that is known to be stable, and that either a whole-car conditioning system or an inverter should be used on one with a, shall we say, "less than stable" power supply (PG version ).
Jack45 said:
I appreciate your detailed, helpful reply.
Other than the important 5v parameter, what I've taken away from your information is that a car charger can be used in a vehicle with a power supply that is known to be stable, and that either a whole-car conditioning system or an inverter should be used on one with a, shall we say, "less than stable" power supply (PG version ).
Click to expand...
Click to collapse
Pretty much ...
There's more than one way to skin a cat, and that Transformer will cost you a whole lot less than a 2 Farad capacitor. I hate cats, but they serve a purpose.
@Battlehymn - one more question for you
I have converted from iPhone to the captivate (no haters please) - finally found a physical form factor with specs i like and the captivate rocks.
Anyway, I have some extra external batteries I used with my iphone that i want to use with my Captivate. I just bought a Female iPod connector and I am planning to connect it to a micro USB connector - the pinout is straight forward, but here is my question:
Should I connect the D+/- (short them together)? That is my plan. My batteries are 1900 or 1000 mAH - I assume that even if the phone tries to the draw 1.8A, the batteries have a circuit to only discharge so fast.
So my DHD arrives tomorrow.
After reading about battery life, I want access to as many chargers as possible.
Can you tell me: Will my existing Micro-USB Chargers (Blackberry) be compatible with the DHD? I'm not sure if each unit will require a specific voltage / wattage?
Or can I just plug & play with which ever Micro-USB charger I come across?
Thank you & sorry if it's a dumb question...
Any cable will do fine. Definitely if you're charging through a PC since I've never heard of a phone/battery that can't handle the 5V it outputs (max for USB charging). A mains charger you can never be too sure with since it may have higher current/watt output, but I've really never let this stop me except that I'd avoid using cheap Chinese knockoffs.
It depends... microUSB connected to computer will be of course good, as it is hardware limited to 0,5A. External chargers are good question, but in my experience the phone/battery usually have a charge limiter so even if the charger does allow you to use higher current, the phone doesn't have to use all the power it can get.
For example i used the Nokia AC-10E charger for my Motorola Milestone since i bough the phone, and had no problems with it. And will use it for DHD too.
The official HTC chargers have an outpur of 5V/1A, so as long as your charger has the same output you should be good.
Nokia AC-10E has 1.2A, but as i said - that is the maximum it can give to the phone, batteries/phones have a current regulators so even if you connect a charger which can give you 2A @ 5V, nothing will happen - the phone will regulate the current which is used to charge the battery.
Im looking to put a couple usb ports in my car, ive found these on ebay and the price seems right.
http://www.ebay.com.au/itm/Car-Led-...Electrical_Test_Equipment&hash=item33772bf4ec
Most other chargers ive seen are either 1.1a or 2.1a, will going up to 3a cause any damage to the device or battery?
A device will only draw as much current as it needs. Current is measured in Amperes, abbreviated A. So if you plug a device that needs 1A into a charger capable of delivering 3A, it will only draw 1A.
Problems occur when you do the opposite, like plug a device that draws 2A (a tablet) into a charger that can only supply 0.5A (500mA, an old phone charger). Then the device won't be able to charge at full rate, or maybe not at all.
As with anything sold on eBay, be wary of claims for chargers. They may not actually deliver the advertised current.
ron917 said:
A device will only draw as much current as it needs. Current is measured in Amperes, abbreviated A. So if you plug a device that needs 1A into a charger capable of delivering 3A, it will only draw 1A.
Problems occur when you do the opposite, like plug a device that draws 2A (a tablet) into a charger that can only supply 0.5A (500mA, an old phone charger). Then the device won't be able to charge at full rate, or maybe not at all.
As with anything sold on eBay, be wary of claims for chargers. They may not actually deliver the advertised current.
Click to expand...
Click to collapse
Thanks for the reply, yeah i hate ebay claims when it comes to stuff mainly from china, batterys, memory cards etc.
Hopefully it works well, even if it's only 1/3 of the claimed output ill be happy for the price.
I spent much time to research, ask sony support, google... but i dont have answer yet...
I have got: (Everything is 5.0VDC)
Xperia Tablet Z (It comes with 1500mA charger)
MDR1-RBT BT Headphones (It comes with no charger, charge only via USB PC port - 500mA?)
MW600 BT Headset (It comes with 350mA cherger)
Can i charge all with 1500mA charger without ANY issues?
Please help me i can't get answer for long...
Please help.
BUMP
It'll eventually damage it
Sent from my Karbonn A15 using XDA Premium 4 mobile app
Will damage the headphones
Sent from my GT-I9100G using xda app-developers app
arvin07143 said:
Will damage the headphones
Sent from my GT-I9100G using xda app-developers app
Click to expand...
Click to collapse
So i can charge it only via USB to PC?
Sony supporter said i can charge it with adaptor with specs 1500mA...
I don't understand it at all...
BUMP!
This one is not quite so straightforward without knowing about the internal circuitry of those devices you have in regards to how they charge.
Now, in general, it is safe to say that you must always match the voltage and polarity of the device you are charging, often you can use a higher rated current charger or power supply.
Why?
A device typically only draws how many amps it needs in order to function.
Take your TV for example, it probably only needs 2-3 amps to run yet it is plugged straight into the mains which has the capability of supplying many hundred of amps yet your TV doesn't "fry", it simply draws what it needs.
When it comes to charging its a bit more complicated and depends on the device (does it have internal charging circuitry or is the the item you plug into the wall and actual charger and not simply an AC/DC converter).
Most small electronics which contain a battery and are simply supplied with an AC/DC converter, say, Input 120V 1A output 5V 100ma have their own current regulating charging circuitry inside. This means that the thing you plug into the wall isn't actually a charger, its an AC/DC converter.
In that case the converter can have a higher rated amp output than your device states it needs because your device will only draw what it wants.
If what you are plugging into the wall is an actual charger which has the job of regulating the current flow to the device that needs charging then you will want to get one as close to spec as the original so as not to damage your device.
All the devices you list seem to charge via 5V, most likely a USB type interface.
This means that they are not supplied with actual chargers, simply power supplies, the charging and current limiting mechanism is inside each device.
In theory therefore you should be able to 'charge' all your devices via the 1500mA AC/DC converter, the products you have will only draw what they need in order to charge, the 1500mA will not be pushed or forced upon each device.
Also, think of this, you have been smart and come to ask for advice, how many people simply use the USB 'charger' of their husband/wife/sister/brother to charge their phone or product when they can't find their own and those devices aren't damaged.
The only thing is if the current is too low then it will either not charge or take much longer.
I hope that helps.
zasy99 said:
This one is not quite so straightforward without knowing about the internal circuitry of those devices you have in regards to how they charge.
Now, in general, it is safe to say that you must always match the voltage and polarity of the device you are charging, often you can use a higher rated current charger or power supply.
Why?
A device typically only draws how many amps it needs in order to function.
Take your TV for example, it probably only needs 2-3 amps to run yet it is plugged straight into the mains which has the capability of supplying many hundred of amps yet your TV doesn't "fry", it simply draws what it needs.
When it comes to charging its a bit more complicated and depends on the device (does it have internal charging circuitry or is the the item you plug into the wall and actual charger and not simply an AC/DC converter).
Most small electronics which contain a battery and are simply supplied with an AC/DC converter, say, Input 120V 1A output 5V 100ma have their own current regulating charging circuitry inside. This means that the thing you plug into the wall isn't actually a charger, its an AC/DC converter.
In that case the converter can have a higher rated amp output than your device states it needs because your device will only draw what it wants.
If what you are plugging into the wall is an actual charger which has the job of regulating the current flow to the device that needs charging then you will want to get one as close to spec as the original so as not to damage your device.
All the devices you list seem to charge via 5V, most likely a USB type interface.
This means that they are not supplied with actual chargers, simply power supplies, the charging and current limiting mechanism is inside each device.
In theory therefore you should be able to 'charge' all your devices via the 1500mA AC/DC converter, the products you have will only draw what they need in order to charge, the 1500mA will not be pushed or forced upon each device.
Also, think of this, you have been smart and come to ask for advice, how many people simply use the USB 'charger' of their husband/wife/sister/brother to charge their phone or product when they can't find their own and those devices aren't damaged.
The only thing is if the current is too low then it will either not charge or take much longer.
I hope that helps.
Click to expand...
Click to collapse
I know that Xperia tablets and phones won't take more mA than it needs but does MDR1-RBT has the same thing? I did a lot of research but i still can't find the 100% answer. I don't want to try unless 100% sure. (Its expensive headphones)
EDIT:
Few sony supporters said: You can charge it only via USB cabble to Personal computer
Few sony supporters said: You can charge it only via USB cabble to PC or Adaptor (Linked me to USB/AC Adaptor with THE SAME specs like XTZ charger - 1500 mA)
Is Adaptor same as XTZ?
I found this on OFFICIAL Sony eSupport
http://docs.esupport.sony.com/portable/MDR1RBT_guide/en/contents/01/03/01/01.html?search=charg
OFFICIAL TIPS:
Tips
If the micro-USB cable is connected to a computer while the headset is turned on, the headset will be turned off automatically.
To charge the headset from an AC outlet, use USB Charging AC Power Adaptor* (sold separately). For details, refer to the manuals supplied with the USB Charging AC Power Adaptor.
The headset cannot be turned on while charging the battery.
* Refer to the Reference Guide on the recommended adapter.
Click to expand...
Click to collapse
BUMP
Zas99 answer is spot on.once the voltage matches to your device your ok.most phone chargers you can pull out the usb charging cable. u could use that or buy a another usb charger at 1500ma to 2000ma.
Sent from my HTC Desire S using xda premium
E7ite: You should be fine, the fact that it charges via USB means that it must have its own internal charging circuitry.
I bet your Xperia tablet also charges via a USB type cable right, on a USB port?
All my USB 'chargers' have different mA rating yet they charge my products just fine as long as the mA rating is at LEAST what the device needs, not less, and hey, if its a little less it also works, just takes longer.
Look at it this way, the USB specs are always changing as is their current handling capability, now we are at USB 3.1, just recently we were at USB 3.0 which bumped up maximum device current usage during data transmission to 900mA or for dedicated charging 1.5A.
For USB 1.x - 2.0 it was 100mA before negotiation, up to 500mA thereafter, also with a dedicated charging capacity of 1.5A if the D- & D+ pins are shorted.
I bet Sony doesn't tell you that you can only charge via a USB 1.x - 2.0 port do they? Nope, that means if your computer has a USB 3 port that its has the potential to deliver more, remember, that's the key, it CAN deliver more if needed but it won't, it will only give the device what it draws.
The cable they supply with your headphone is most likely not a data cable but rather a so called charging cable so therefore is rated up to 1.5A or 1500mA but your headphones will only draw what they need to charge.
Everyone uses the term charger which is so wrong, when you put your AA or AAA batteries into the little black box and plug it into a wall, that is a charger, when you connect your car battery via the +/- terminals and clamps to the charger, that is also a real charger, they are directly responsible for charging the batteries.
All these other things we use to 'charge' our little electronic devices do nothing other than take the 120V A/C and convert it into for example 5V DC. The current rating they indicate next to the 5V is simply the max current handling capability, nothing more, it not what is pushed to the device, its what the device can request up to to be delivered. The actual charging goes on inside the device.
By the way, as the batteries charge the device reduces the current and sometimes also the voltage, batteries typically charge faster when they are low and able to absorb more current then as they fill up and can absorb less the charger adjusts to a more or less trickle such as 100mA or less in order to maintain but not overcharge the battery.
By the way, this is what I found on Amazon in about 2 minutes, a review from someone else who bought the headphones.
"For the price, sony should have included a wall charger. Instead they included a USB cable. The headphones will charge on any computer, but using a generic USB wall charger will show a blinking amber error light--but the headphones still charge."
Also, the link you indicated to the sony manual about charging gives absolutely no information at all.
You are over thinking it, just try it
If you are really worried why not get a regular cell phone USB charger and use that, one that states like 500mA on it and has a female USB plug on it. That way you can use your headphone USB cable and plug it into the 5V 500mA phone 'charger'.
One last thing, just don't use Apple product 'chargers' to charge non Apple products, why you ask, because Apple does strange things with the pins on their 'chargers' in order to indicate the supply current. This can sometimes lead to adverse effects for non Apple devices.
Good luck.
zasy99 said:
E7ite: You should be fine, the fact that it charges via USB means that it must have its own internal charging circuitry.
I bet your Xperia tablet also charges via a USB type cable right, on a USB port?
All my USB 'chargers' have different mA rating yet they charge my products just fine as long as the mA rating is at LEAST what the device needs, not less, and hey, if its a little less it also works, just takes longer.
Look at it this way, the USB specs are always changing as is their current handling capability, now we are at USB 3.1, just recently we were at USB 3.0 which bumped up maximum device current usage during data transmission to 900mA or for dedicated charging 1.5A.
For USB 1.x - 2.0 it was 100mA before negotiation, up to 500mA thereafter, also with a dedicated charging capacity of 1.5A if the D- & D+ pins are shorted.
I bet Sony doesn't tell you that you can only charge via a USB 1.x - 2.0 port do they? Nope, that means if your computer has a USB 3 port that its has the potential to deliver more, remember, that's the key, it CAN deliver more if needed but it won't, it will only give the device what it draws.
The cable they supply with your headphone is most likely not a data cable but rather a so called charging cable so therefore is rated up to 1.5A or 1500mA but your headphones will only draw what they need to charge.
Everyone uses the term charger which is so wrong, when you put your AA or AAA batteries into the little black box and plug it into a wall, that is a charger, when you connect your car battery via the +/- terminals and clamps to the charger, that is also a real charger, they are directly responsible for charging the batteries.
All these other things we use to 'charge' our little electronic devices do nothing other than take the 120V A/C and convert it into for example 5V DC. The current rating they indicate next to the 5V is simply the max current handling capability, nothing more, it not what is pushed to the device, its what the device can request up to to be delivered. The actual charging goes on inside the device.
By the way, as the batteries charge the device reduces the current and sometimes also the voltage, batteries typically charge faster when they are low and able to absorb more current then as they fill up and can absorb less the charger adjusts to a more or less trickle such as 100mA or less in order to maintain but not overcharge the battery.
By the way, this is what I found on Amazon in about 2 minutes, a review from someone else who bought the headphones.
"For the price, sony should have included a wall charger. Instead they included a USB cable. The headphones will charge on any computer, but using a generic USB wall charger will show a blinking amber error light--but the headphones still charge."
Also, the link you indicated to the sony manual about charging gives absolutely no information at all.
You are over thinking it, just try it
If you are really worried why not get a regular cell phone USB charger and use that, one that states like 500mA on it and has a female USB plug on it. That way you can use your headphone USB cable and plug it into the 5V 500mA phone 'charger'.
One last thing, just don't use Apple product 'chargers' to charge non Apple products, why you ask, because Apple does strange things with the pins on their 'chargers' in order to indicate the supply current. This can sometimes lead to adverse effects for non Apple devices.
Good luck.
Click to expand...
Click to collapse
Thank you for reply.