Ive been pulling my hair out over this for about 6 hours.
I cannot get my CHT softkey bar to line up properly with the screen. I attached a couple of screens shots to show my problem EVERYTIME. The only time it went all the way down is when i stretched my image the whole 512x128.
What im trying to do is get the bottom edge of the graphic to line up perfectly with the bottom of the screen.
If anyone could show or explain to me how to accomplish this it would be greatly appreiciated.
ericv99 said:
Ive been pulling my hair out over this for about 6 hours.
I cannot get my CHT softkey bar to line up properly with the screen. I attached a couple of screens shots to show my problem EVERYTIME. The only time it went all the way down is when i stretched my image the whole 512x128.
What im trying to do is get the bottom edge of the graphic to line up perfectly with the bottom of the screen.
If anyone could show or explain to me how to accomplish this it would be greatly appreiciated.
Click to expand...
Click to collapse
Ok I have made quite a few Softbars now, so I might be able to help you
I uploaded i little pic with a previous work of mine.
There are 2 lines in it. The upper line (completely red) shows you what is the limit of what is displayed on the screen. Everything above this line will be displayed.
The space between the 2 lines is more or less not necessary
and everything you see below the lower line will be stretched to be the menu panel when the cht softbar slides up
It is however the case, that the part between two lines will fill the lower like 5 pixels of the screen so you want to adapt that to the rest of your softbar, so that it fits
But normally if the upper design reaches down to the upper line there shouldnt be any problem
Nordpolcamper said:
Ok I have made quite a few Softbars now, so I might be able to help you
I uploaded i little pic with a previous work of mine.
There are 2 lines in it. The upper line (completely red) shows you what is the limit of what is displayed on the screen. Everything above this line will be displayed.
The space between the 2 lines is more or less not necessary
and everything you see below the lower line will be stretched to be the menu panel when the cht softbar slides up
It is however the case, that the part between two lines will fill the lower like 5 pixels of the screen so you want to adapt that to the rest of your softbar, so that it fits
But normally if the upper design reaches down to the upper line there shouldnt be any problem
Click to expand...
Click to collapse
again.. you come to save the day.. haha..
thank you for that..im gonna have a another go at it. lets see what comes up...
im still getting that gap.
check out my file and tell me what im doing wrong..
ericv99 said:
im still getting that gap.
check out my file and tell me what im doing wrong..
Click to expand...
Click to collapse
I adjusted some little things in the psd try it this way there shouldnt be anything wrong now If you leave the space between the two line black it will normaly produce the gab you were talkin about
it still happens... it like just cuts it off too short..
ericv99 said:
it still happens... it like just cuts it off too short..
Click to expand...
Click to collapse
Yes I thought that this might happen. That means, that you have to shrink the upper part a little and move it upwards.
Nordpolcamper said:
Yes I thought that this might happen. That means, that you have to shrink the upper part a little and move it upwards.
Click to expand...
Click to collapse
Yes, as said above and in some instances, I have found it easiest, just to adjust the softkey height just slightly in CHTeditor.
Sometimes that seems to be another simple enough workaround.
In the attached pic you see the red line across the top of the phone for LED notifications
but when there is a notification a tiny faint almost impossible to see (ie pointless for a notification) dot is flashing just on the right side.
Is this red string of what looks like red lights spanning most of the width of the phone so it can flash using more or all of the width?
pwoita said:
In the attached pic you see the red line across the top of the phone for LED notifications
but when there is a notification a tiny faint almost impossible to see (ie pointless for a notification) dot is flashing just on the right side.
Is this red string of what looks like red lights spanning most of the width of the phone so it can flash using more or all of the width?
Click to expand...
Click to collapse
That image you have is of a sensation XE. The red colour is just paintwork on the speaker housing to compliment the other red highlights found on the XE. It's not a row of lights. The dot is all there is. If you take the cover off while you have a notification, you'll see there are no more led's on the phone for what you're looking for.
TL;DR: impossible.
ah ur right.
gaaaaaah.
<random complaining about stupid design of hard to see tiny LED>
thanks for the response
Has anyone else, looking close at the display, noticed that when you have a white object or shape on the screen, there is a green outline on top and a red outline on the bottom? Is this just my device or is it a side effect of amoled displays.
I've attached an image of the X button for multitasking zoomed in because that's where it's most noticeable.
EDIT
Never mind turns out that it is to do with the pentile display matrix that optic amoled displays use.
Here's a link explaining it if anyone's interested https://www.androidauthority.com/galaxy-note-2-vs-galaxy-s3-display-comparison-rgb-pentile-121182/
Hello guys,
My pixel 3a at low brightness it starts from the upper right corner to illuminate the screen and as I get on the side it also illuminates from the other sides.
it's normal??
Watch this on phone app and contact because the color Is grey
The picture in picture screen does not move anywhere.
o this is not a glitch. Samsung actually added borders that the picture in picture screen can't go in.
Is there anyway to unlock the edges of my screen? When watching videos I'm sure everyone would prefer it in the corner. Not middle of screen. So u can work and watch easily. 
in my case, the floating window can be moved to any position to the sides, that is, it always stick to the left or right sides