Related
Fix Xperia C Red Light brick
Are you facing that the red led on your device blinks and there is no other signs of life? Then you are in the correct thread, I faced this issue when flashing a corrupted recovery but then I found out a easy way to fix it without opening the device or sending it in to Sony.
Requirements:
Xperia C with red light softbrick
MicroUSB Cable
Sony Update Service
Click to expand...
Click to collapse
1. The first thing you need to do is to make sure that you have downloaded Sony Update Service and have installed it onto your PC from the link above, if not, do it now.
2. Now launch Sony Update Service and select Xperia C in the list and then press Next.
3. Hold the Volume Up button and plugin microusbcable while doing so, if that doesn't work for you, hold power + volume up and plugin the microusbcable while doing. Keep holding button combination for a few seconds and wait for a green light on your phone, if it appears check on
your PC so that it's detected.
4. Wait while the firmware is being downloaded and reinstalled on your phone and enjoy your working device!
Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best
chauhanjayc said:
Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best
Click to expand...
Click to collapse
I flashed a faulty recovery using mobileuncles and there was no signs of life other than a red led liggt, and holding power + volume up works just fine and it went into flashmode.
I have the same issue.
I organized xperia light rom for our xperia c, I flashed it from custom recovery. Phone is completely dead now.
There is a just red light, phone does not go into download or fastboot mode. Pc Companion, Sony Update Center, Wmshua Flashtool do not recognize the phone.
Any suggestion with that?
I don't have warranty, my last option is to pay money for technical service.
this worked for me but instead of POWER+VOL UP i used POWER+VOL DOWN
thanks
thank, i like this forum
worth to try... (hope it won't happen to me :laugh: )
I have experienced this too, however, instead of using the Sony Update Service, I used the Sony PC Companion. At first it was not working, so I did a hard reset on the phone (press the button at the back). I held the power+up button while inserting the cable, and finally it was detected by Sony. It will reset your device to factory settings though.
seiferfury said:
I have experienced this too, however, instead of using the Sony Update Service, I used the Sony PC Companion. At first it was not working, so I did a hard reset on the phone (press the button at the back). I held the power+up button while inserting the cable, and finally it was detected by Sony. It will reset your device to factory settings though.
Click to expand...
Click to collapse
How did it
How Catch 4 buttons simultaneously
Please reply to the importance of
Im in the same scenario.. I tried all the procedures here but i failed.. I noticed that when i connect it, it disconnects after a while along with blinking of led light then reconnect again. And my PC detects it as unknown device.. I tried to install ADB driver but it also fails. Please help me.. Thanks. Sorry about my English
zergmac023 said:
Im in the same scenario.. I tried all the procedures here but i failed.. I noticed that when i connect it, it disconnects after a while along with blinking of led light then reconnect again. And my PC detects it as unknown device.. I tried to install ADB driver but it also fails. Please help me.. Thanks. Sorry about my English
Click to expand...
Click to collapse
If you flash a different device's rom, it happens. If you replace your motherboard, it will work again.
(
TacoNikky said:
If you flash a different device's rom, it happens. If you replace your motherboard, it will work again.
Click to expand...
Click to collapse
Which probably crying::crying::crying:
yeubeo168 said:
Which probably crying::crying::crying:
Click to expand...
Click to collapse
I have bought motherboard from china http://www.yoybuy.com/en/show/37431065583/ from this seller.
It took 20 days to arrive to Turkey. I have changed my motherboard and my phone is back right now :victory:
It works like a charm. Model number changed, it shows s39h but phone works like old days :good:
A detailed guide :
http://forum.xda-developers.com/sony-xperia-c/general/how-to-install-restore-stock-android-t2832005
It worked!!!!!
GethPrime said:
Fix Xperia C Red Light brick
Are you facing that the red led on your device blinks and there is no other signs of life? Then you are in the correct thread, I faced this issue when flashing a corrupted recovery but then I found out a easy way to fix it without opening the device or sending it in to Sony.
Requirements:
1. The first thing you need to do is to make sure that you have downloaded Sony Update Service and have installed it onto your PC from the link above, if not, do it now.
2. Now launch Sony Update Service and select Xperia C in the list and then press Next.
3. Hold the Volume Up button and plugin microusbcable while doing so, if that doesn't work for you, hold power + volume up and plugin the microusbcable while doing. Keep holding button combination for a few seconds and wait for a green light on your phone, if it appears check on
your PC so that it's detected.
4. Wait while the firmware is being downloaded and reinstalled on your phone and enjoy your working device!
Click to expand...
Click to collapse
It worked for my Xperia M (rooted on JB 4.3) with a locked bootloader which was STUCK on bootloop screen and when I did the whole thing with holding the power and volume up button (after I let the battery die after so many bootloops it did), FINALLY I was able to take it to flashmode, while I had selected from Sony PC Companion to repair my phone, and after 3-4 tries, I DID IT!!! Thank you so much for this thread ( I DEFINITELY pressed the "thanks" button), it really SAVED ME time and money (because I was planning to send it to Sony to fix it and you ALL know how bastards Sony is)!!!! And to all those of you who are DESPERATE to fix their phone (I hope you read this thread), DON'T PANIC, and DON'T GIVE UP!!! It took me 2 days of searching the web, and FINALLY I MADE IT!!! There are ALWAYS solutions to these kinds of problems!!!!
red light
dear friends please help me. I wanted to install cwm recovery with mobile uncle tools. when I placed recovery.img to phone memory(not in any folder), it didn't find the file, but when in sd card(not in any folder) it succesfully find. I selected and flashed, but the phone shut down and didn't start anymore. yesterday, when plugging to charge the red light under the screen was blinking. but today, it just stays on, not blinking, but after some time, goes off again, and start blinking. when I connect to PC, first it connects, after some time connection is lost and green light passes to red again, after some time it again connects. I tried Sony Update Service and PC Companion, didn't work. Please help...
Need help
same here only red light is blinking,,,i tried doing Power+vol up and Power+vol down and by inserting cable also...it just show a red light when plugged in
i'm also having the same problem....somebody please help!!!!really need to use it
kamran.kerim said:
dear friends please help me. I wanted to install cwm recovery with mobile uncle tools. when I placed recovery.img to phone memory(not in any folder), it didn't find the file, but when in sd card(not in any folder) it succesfully find. I selected and flashed, but the phone shut down and didn't start anymore. yesterday, when plugging to charge the red light under the screen was blinking. but today, it just stays on, not blinking, but after some time, goes off again, and start blinking. when I connect to PC, first it connects, after some time connection is lost and green light passes to red again, after some time it again connects. I tried Sony Update Service and PC Companion, didn't work. Please help...
Click to expand...
Click to collapse
i'm also having the same problem....somebody please help!!!!really need to use it
chauhanjayc said:
Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best
Click to expand...
Click to collapse
Does that mean phone is dead?
choxx said:
Does that mean phone is dead?
Click to expand...
Click to collapse
no all you need stock kernel
you can either google it or download ftf and check all except kernel
done
Hi. My device is hardbricked. I see no lights while charging. Flashtool doesn't see my device.how can i fix this?
Edit:Easily fixed it.I plugged my device into the computer.I entered platform-tools and flashed boot.img.I saw "waiting for device" And i pressed volume up and power buttons. Suddenly boot flashed and i recovered my phone
You are very unlikely to have hard bricked it unless you have unlocked the boot and flashed something wrong.
If you did this please help us help you by telling us what you did just before this happened.
Also, just leave the phone on charge (Wall charger) for 24 hours and then see what happens.
In the mean time read this
solution for no LEDs no response no fastboot devices.
Take two rubberbands one to hold down the power button and one to hold down the volume up button on Xperia Z3 dual. I spent a lot of time figuring this out. Alter a few minutes the phone just booted up from the dead. It worked for me 3 times. Now if someone can tell me how to fix the fastboot remote command not allowed error I'll be happy.
Fastboot remote command not allowed SOLVED
stevenmanzano said:
Take two rubberbands one to hold down the power button and one to hold down the volume up button on Xperia Z3 dual. I spent a lot of time figuring this out. Alter a few minutes the phone just booted up from the dead. It worked for me 3 times. Now if someone can tell me how to fix the fastboot remote command not allowed error I'll be happy.
Click to expand...
Click to collapse
Hello
I had the same problem with REMOTE COMMAND NOT ALLOWED till i managed to solve it.
1st thing you need to clean that ANDROID folder you made on C: drive.Install all from the begining including flashtool.Boot windows to install unsigned drivers.In the flash tool folder youll find the driver downloader,just enable usb debugging and choose Mass Storage not MTP .; You have 4 options usb debug on/off and usb connectivity MTP or Mas Storage ;with every version selected connect and disconnect from pc with flashtool running.
When you use Fastboot start the flashtool and close it if it cant kill ADB (that assuming you succeeded in installing drivers).
Good Luck
Please tell me D6603 testpoint
bgbgtbvan said:
Please tell me D6603 testpoint
Click to expand...
Click to collapse
you must read this
http://forum.xda-developers.com/showthread.php?t=2646405&page=54
john abruzzi said:
you must read this
http://forum.xda-developers.com/showthread.php?t=2646405&page=54
Click to expand...
Click to collapse
i have an xperia e3 d2212 stuck pon sony logo....bootloader is unlocked....i m able to enter fastboot so i flashed kernel.sin and system.sin after extracting from stock ftf but it didnt workwed...also,,i m not able to enter flash mode as the flash tool doesnt detects it in flashmode...but when i press power button and volume down the green led lights up...i have reinstalled flashtool many times and also reinstalled the drivers many times...any fix for this??
mihir762000 said:
i have an xperia e3 d2212 stuck pon sony logo....bootloader is unlocked....i m able to enter fastboot so i flashed kernel.sin and system.sin after extracting from stock ftf but it didnt workwed...also,,i m not able to enter flash mode as the flash tool doesnt detects it in flashmode...but when i press power button and volume down the green led lights up...i have reinstalled flashtool many times and also reinstalled the drivers many times...any fix for this??
Click to expand...
Click to collapse
Try a different driver package from another download source and use another usb on your pc.
Maybe it works. If your device can enter flash mode it definitely can be recovered.
Omario-242 said:
Try a different driver package from another download source and use another usb on your pc.
Maybe it works. If your device can enter flash mode it definitely can be recovered.
Click to expand...
Click to collapse
first of all my phone cant enter flashmode..(just the green light lits up)..secondly,,i have tried to reinstall drivers many times and i have tried to flash the system.sin and kernel.sin of 3 diffrent ftf rom for xperia e3 dual....is there any other solution..???
mihir762000 said:
first of all my phone cant enter flashmode..(just the green light lits up)..secondly,,i have tried to reinstall drivers many times and i have tried to flash the system.sin and kernel.sin of 3 diffrent ftf rom for xperia e3 dual....is there any other solution..???
Click to expand...
Click to collapse
The green led indicates flash mode so the problem is probably on your PC not detecting it properly. Does it show up in the system manager of windows if you plug it in at all? (Like a new device/android with a yellow triangle)
You could also try to fastboot a recovery and flashing a ROM from there. Not sure if it works but that's what I would try.
i m not even able to fastboot a recovery ...tried twrp and cwm both of them...
Me too
in my phone after charging 24h, only the red LED blinks, this is not normal any suggestions?
--------------edit
ok another week and still nothing
maybe I'll describe the problem:
I wanted to upload clean soft 5.1.1 and flash it
after the phone turned off it's start in recovery i used zip with SU and the phone turned off with no respond i try too reset (vol- + vol+ + power) but no reaction
there were no three vib
so I found that you have to reset the button under the sd flip
after this treatment you already know the charging of 3 days and only the red LED blinks
So any suggestions??
|
I‘m having the same problem, I can’t open my Xperia Z3. I tried with holding on/off button, holding volume up and on/off button, holding volume down and on/off button. When I connect it to PC, nothings happen. No vibrates, no led on, no screen on. What should I do?
ibo90p said:
I‘m having the same problem, I can’t open my Xperia Z3. I tried with holding on/off button, holding volume up and on/off button, holding volume down and on/off button. When I connect it to PC, nothings happen. No vibrates, no led on, no screen on. What should I do?
Click to expand...
Click to collapse
Like you I have a Xperia Z3 mines the 6633 variant.. Signs were showing it to be hard bricked, for example:
No led charge indication!
No power led!
No fastboot leds!
No USB detection sound when plugging into windows.
Literally a Z3 that was essentially a glass brick I bought off ebay for £6.50 GBP for spares/repair.
Since I had a bricked device, I had nothing to loose.
I applied heat to the rear glass with a hair drier & removed the panel, I removed the battery ribbon cable & plugged in via USB only to find the phone would show LEDs so put it on charge.
The Z3 now goes into flash mode, so then re-flashed a stock ROM from flashtool. I did a apps log & user data wipe, cust reset & fota reset.
To date I have no idea why the phone would not take a charge before or even detect via USB, though Id say give this method a go, you may be surprised!!
Good luck
I have a d6603 Z3 on 5.1.1. I attempted to use flashtool to downgrade my firmware as per this thread: http://forum.xda-developers.com/z3/general/guide-rootrecovery-how-to-root-install-t3017056
After allowing it to flash, the last lines were:
10/058/2015 23:58:25 - INFO - Please unplug and start your phone
10/058/2015 23:58:25 - INFO - For flashtool, Unknown Sources and Debugging must be checked in phone settings
Once I did that, the phone would start and during the boot process it would freeze and restart. Connecting to my computer shows that the battery is at 50% no matter how long it's connected. I've tried holding the power button with volume up, or power with volume down, and doing those two while connecting to computer, and nothing. Pressing the yellow button and getting the vibrations don't help. Trying to use PC Companion Repair, but that's not getting anywhere because when I hold the volume button while connecting the device, it doesn't recognize the device. Sometimes the phone will vibrate once while holding volume down when I do that. Still nothing. I'm at my wits end here.
looks like software brick. If you havent unlocked the bootloader go to service center and get it done. but you will get latest 5.1.1.
dont tell them you used flashtool n all.
Hmm, I'll have to wait til support lines open up. I'll report back sometime in the morning/afternoon.
I've just contacted Sony. They want me to send the device in for repair. I didn't tell them what I was attempting to do, only that I was in a boot loop.
inPHiniTe said:
I've just contacted Sony. They want me to send the device in for repair. I didn't tell them what I was attempting to do, only that I was in a boot loop.
Click to expand...
Click to collapse
I was in the same case and resolved it that way :
Note : locked bootloader
* installed flashtool on my computer (debian 8) : http://www.flashtool.net
* downloaded stock firmware for my isp (orange, france) : http://forum.xda-developers.com/z3/general/ftf-stock-firmwares-xperia-z3-models-t2886061
* followed http://forum.xda-developers.com/showpost.php?p=45187952&postcount=2 to flash the ftf using flashtool
* got my phone erased and back to stock KK but no more boot loop, and no sending to sony for repair.
Hope this helps and will work for you.
If you use pc companion try going into fix phone and manually select the phone model your fixing and it should force a flash through. Your just going to have to charge it up a bit if possible.
Worked for my boot looping D6616 which I had never hooked up to pc companion before.
Best of luck
Sent from my D6616 using XDA Free mobile app
Hello, I need help with my Z3 with these symptoms:
-When plugging the USB to a PC, it won't show up. But it does pops a sound on the PC; the S1 Service appears on the device list. Dissapears when unplugged
-When plugged to a PC the phone flashes a red light for a moment, then a green one really fast before the led goes off again.
-If i hold the power button, the phone vibrates a bit. No screen or led are light give any signal.
-If I hold the vol- button plus the power up button, the screen goes up and Sony - XPERIA logo briefly. But it won't start at all and goes back to black.
-If the vol+ plus power buttons are holded together, the phone will vibrate 3 times.
It was working fine just before i tried to install ZyxxOS. I rooted it previously with Kingo ROOT. Then used the Z3-lockeddualrecovery2.8.26-RELEASE.combined. Used the Install.bat. On the dual recovery mode I installed the ZIP, when it looked like it was done I cleared the cache and followed the dialogs. Then a message poped up saying my device was not rooted and offered me to root it. After it the phone went black and the CMD looked like was doing nothing. I left it like that around 25 mins and then unplugged the USB. After I tried to start the phone it didn't worked anymore.
I'd be really glad if someone is able to help me :crying:
Seems like a drained battery and a system corrupted. Try holding the power down for 30 secs, to make sure the phone is turned off, then leave it charging for a while, and when I mean "a while" Im saying put it in charge and go to sleep. The next day the phone will be with full battery for sure, then, download and install FlashTool and install the drivers from the folder of the program after installed, then try the steps mentioned here:
http://forum.xda-developers.com/xperia-z/general/tutorial-how-to-flash-stock-roms-t2240614
The tutorial is for the Xperia Z, but the steps are basically the same.
On the newer versions of flashtool, there is an new option to download the stock firmware from the program, wich is usefull if you dont know where to search, and more secure, since the z3 has many different models, make sure to download the correct firmware for the model of your phone, to know the model, just open the chip flap and you'll see a small piece of plastic above the sim slot, pull it and you'll see some information, look for the model, ex: "D6653"
answer if it works!
Wish you the best!
nameless-- said:
Seems like a drained battery and a system corrupted. Try holding the power down for 30 secs, to make sure the phone is turned off, then leave it charging for a while, and when I mean "a while" Im saying put it in charge and go to sleep. The next day the phone will be with full battery for sure, then, download and install FlashTool and install the drivers from the folder of the program after installed, then try the steps mentioned here:
http://forum.xda-developers.com/xperia-z/general/tutorial-how-to-flash-stock-roms-t2240614
The tutorial is for the Xperia Z, but the steps are basically the same.
On the newer versions of flashtool, there is an new option to download the stock firmware from the program, wich is usefull if you dont know where to search, and more secure, since the z3 has many different models, make sure to download the correct firmware for the model of your phone, to know the model, just open the chip flap and you'll see a small piece of plastic above the sim slot, pull it and you'll see some information, look for the model, ex: "D6653"
answer if it works!
Wish you the best!
Click to expand...
Click to collapse
Thanks. But is it needed the device shows in my computer?
http://s32.postimg.org/uush6rzgl/image.png
Also, when I try to use the Flash tool I don't get it to see it on the list.
http://s32.postimg.org/st1n3dx6t/device.png
Also, I charged it a whole day, but it never appeared nothing on screen, just the red light blinking.
Wong17 said:
Thanks. But is it needed the device shows in my computer?
http://s32.postimg.org/uush6rzgl/image.png
Also, when I try to use the Flash tool I don't get it to see it on the list.
http://s32.postimg.org/st1n3dx6t/device.png
Also, I charged it a whole day, but it never appeared nothing on screen, just the red light blinking.
Click to expand...
Click to collapse
Looks like you're connected, but you don't have any FTF's downloaded. Download FTF for your model, put it in C:\users\Wong\.flashTool\firmwares.
Then while holding volume down button connect your phone to PC. If it says "Device connected in flashmode" you suceeded. Then click on lightning icon on flashtool select your FTF and flash it. Hope I helped.
@Wong17
You also need a unlocked bootloader to install ZyxxOS on your device.
Wong17 said:
Thanks. But is it needed the device shows in my computer?
http://s32.postimg.org/uush6rzgl/image.png
Also, when I try to use the Flash tool I don't get it to see it on the list.
http://s32.postimg.org/st1n3dx6t/device.png
Also, I charged it a whole day, but it never appeared nothing on screen, just the red light blinking.
Click to expand...
Click to collapse
Nojus33 said:
Looks like you're connected, but you don't have any FTF's downloaded. Download FTF for your model, put it in C:\users\Wong\.flashTool\firmwares.
Then while holding volume down button connect your phone to PC. If it says "Device connected in flashmode" you suceeded. Then click on lightning icon on flashtool select your FTF and flash it. Hope I helped.
Click to expand...
Click to collapse
Yep, seems that you only need to download the FTF for you phone, you can use XperiFirm option on the Flashtool to download the firmware for you model.
Then just do what Nojus said, connecto to the PC holding Volume down, the flashtool will recognize it, the led will light up and you're set to reflash your device again.
I think you tryied to flash the ZyxxOS without unlocking your bootloader, then you corrupt all your system and It went to a softbrick state.
Post the results here! :fingers-crossed:
Hello There
I was trying to hard reset my Sony Z3 D6633 and I firstly wiped the Rom then after that I tried to install Stock Rom using "Sony Mobile Flasher by Androxyde" , unfortunately the power went of while it was flashing and now the phone doesn't even boot or show any thing on the screen , and the led doesn't even blink , I tried the following :
-pressing the volume down then connecting it to the flasher (No Response)
-pressing the yellow reset button in sim tray 10 times then connecting the charger (No Response)
-holding volume up and power together (No response)
I'm currently putting it in charger but it doesn't give any response , I think I deleted an important part in the system , is there's any software that could help me ,if someone could guide me I would be very grateful for him/her
Usually a normal flash with a flash tool shouldn't brick your device in a way that it can't enter stock recovery or download/flash mode.
Did you check the device manager when connecting with volume up/down?
You can try EMMA by Sony to flash full stock, but you need to follow a tutorial to set it up (there's a specific file you need to put in the install directory of the program to skip the devs login).
When connecting the charger does the red LED light up?
Resolved
Sorry for the long absence, after three days of posting this i was about to give up until I plugged my phone into the charger and the led turned on which was a good sign that now I know that the device is still working, after charging it for a couple of hours I connected it to the PC and used "Sony PC Companion" and followed it's steps, and the device was restored to it's original firmware.:laugh::laugh::laugh: