tmous
leedroid 2.1 .16---08 radio
1. anyone using the twrp recovery on leedroid as opposed to cwm and do you like it--read you don't have to boot into recovery to flash new radio zip as it bypasses htc restrictions. And, no need to fastboot separate boot.img when flashing roms like leedroid.
2. also, being on the above rom and radio, i want to flash the newer eu radio .10 either thru cwm (boot into recovery) or twrp straight from recovery--anyone find the .10 better on tmous/leedroid--any issues to be aware of flashing other than check md5, although i didn't see a md5 listed
3. take it i can't extract radio.img and fastboot like on N1----?
Thanks
Ken
I did the same thing you are thinking about doing last week.
I'm on Tmobile USA. On LeeDroid Rom. I was curious and flashed the EU Radio. Now for me I began running into trouble such as the MMS not working properly. But the biggest drawback for ne was that I would have to try to call someone two or three times for the phone to connect. And a lot of the times once someone picked up I could not hear them.
This was my personal experience with the EU radio so I decided to flash the TMO-USA radio again and all was good.
I don't want to discourage you though because there were also some people who were saying that they flashed the EU radio without any problems and that it worked fine for them.
All in all if it doesn't work out for you then you could always just flash the other one.
Sent from my HTC VLE_U using XDA
appreciate your reply ydizzle
i will hold off for now pending other posts, don't know if how you flashed it matters like wiping cache first etc. and as mentioned don't think you can extract and fastboot it without s-off
this phone has been perfect and no issues unlocking/rooting/flashing roms--haven't done a restore yet. this is different from my N1 where i think after two years of rom flashing and running ics i maxed it out, so to speak. i don't want to go back to that, so i will leave radio as is for now. bought this phone planning on not doing a lot of flashing. don't know if i can continue to do that--it is too tempting sometimes--
Same happened to me with the EU radio it was bad
Sent from my HTC VLE_U using XDA
Not looking good for the European radio
I just flashed the Radio which came with the new OTA update with no issues so far. I'll let you guys know if i run into any issues.
No problems with the new radio. Calls and MMS work flawless. Data speed seems to have improved slightly.
Sent from my HTC VLE_U using XDA
ydizzle did you flash the flashable one from the new tmous thread thru cwmr or did you manually extract the radio.img and fastboot into recovery, adb bootloader, and fastboot the radio.img
people seem to have no issue with the flashable zip
i usually prefer fastboot on radios
ken
I flashed the radio through recovery. Didn't wipe anything either.
Sent from my HTC VLE_U using XDA
I will give it a go
You didn't have to copy zip to sdcard, fastboot boot recovery.img first from command window, then flash zip--
I think I might have found an issue. Whenever I am on a phone call my data switches off.
In other words, I can't browse the web while I'm talking to someone.
Before the updated radio this wasn't an issue.
If anyone else has just flashed the new radio, can you reply and lmk if your having this same issue?
i think i heard of this with other tmous radios
i know on eu leedroid one all is perfect
Update: Flashed the Energy Rom and now I have data again during calls. I am a happy camper.
Seems like that Rom has no issues for tmobile USA.
Sent from my HTC VLE_U using XDA
been thinking about that rom, but this one is perfect for me atm--stock radio though. although, i flashed diff radios on n1 and never noticed a difference
may wait for next Energy update as BT is still in doubt for some
just flashed the new tmous radio on latest LeeDroid
no signal strength improvement over pre flashing--still 97 to 101
that low signal is common for my location at home as house sits right under a red, dead zone circle for tmobile--sucks
no big deal as i have wifi at home
will have to test for awhile. but, if no negative effects no reason to go back to old radio
Related
I'm thinking of updating my li'l heroc's radio (currently 2.42.01.04.27) by downloading the appropriate zip and flashing from ClockworkMod recovery. Here's my Q: afterwards, will I need to flash my CM6.1 and gapps all over again?
--
sent from my
rooted little heroc
usin tapatalk pro
Nope, flash the radio, reboot, done
[email protected] said:
I'm thinking of updating my li'l heroc's radio (currently 2.42.01.04.27) by downloading the appropriate zip and flashing from ClockworkMod recovery. Here's my Q: afterwards, will I need to flash my CM6.1 and gapps all over again?
--
sent from my
rooted little heroc
usin tapatalk pro
Click to expand...
Click to collapse
No you wont have to update the rom, gapps, kernel or any other mods you may have. Updating your radio will change your baseband. I was on the same radio you were until I changed my radio to the Verizon desire radio because it gives me better service for sure. I didnt do mine thru clockwork so i dont know how that works I just got the update zip and flashed it in recovery. Be careful using diff methods or zips to flash radios one bad one and u got a brick. Good luck
Sent from my HERO200 using Tapatalk
Just flash and done
theimpaler747 said:
Just flash and done
Click to expand...
Click to collapse
Unless you are using firerats custom partitions. Then it isn't so easy as flash and go, but still not hard to do.
athanos said:
Unless you are using firerats custom partitions. Then it isn't so easy as flash and go, but still not hard to do.
Click to expand...
Click to collapse
Takes about 30 minutes if your using firerats mod, but even then you still dont lose anything.
I flashed baseband 2.42.01.04.27 and still not getting much improved reception in a fringe area (my home). Common to get around -98 to -100 db.
Any suggestions for other radios that might work better on the weak end?
Sprint CDMA USA
windtrader said:
I flashed baseband 2.42.01.04.27 and still not getting much improved reception in a fringe area (my home). Common to get around -98 to -100 db.
Any suggestions for other radios that might work better on the weak end?
Sprint CDMA USA
Click to expand...
Click to collapse
You could try the newest one here: http://forum.xda-developers.com/showthread.php?t=853868
Verizon
dirkyd3rk said:
No you wont have to update the rom, gapps, kernel or any other mods you may have. Updating your radio will change your baseband. I was on the same radio you were until I changed my radio to the Verizon desire radio because it gives me better service for sure. I didnt do mine thru clockwork so i dont know how that works I just got the update zip and flashed it in recovery. Be careful using diff methods or zips to flash radios one bad one and u got a brick. Good luck
Sent from my HERO200 using Tapatalk
Click to expand...
Click to collapse
Hey I had a question about that. By flashing the Verizon radio won't that be considered like Roaming because you're not using Sprint Towers??? Also how is the improvement in say signal strength and data?
Just wondering cause i'd like to improve my phone signal.
-Rock Chalk
yea i wanna know about using verizon towers too... especially for 3g...wasnt there some hack besides flashing radio?
BothGunzUP said:
You could try the newest one here: http://forum.xda-developers.com/showthread.php?t=853868
Click to expand...
Click to collapse
I loaded the latest radio and the numerical signal is about the same but the phone displays two bars once in awhile which never showed before from the same fringe location. Will need more time talking on the phone before deciding if there is any marked audible quality improvement.
The -xx dmb readout and the graphic bar display do not seem to be in synch anyway. It can show -95 dbm and then only one bar while other times I have seen it at -98dbm and showing two bars, so really not sure which is more reliable.
i am at a total loss here.
I was on CM7 with the stock AT&T radio and HSUPA was working just fine.
I then tried to flash another radio (The Telus one) and i lost HSUPA.
I checked the build.prop and it is still showing that HSUPA is enabled.
I tried flashing back to the AT&T stock radio and HSUPA is STILL disabled...
Anyone know how to re-enable this?
I am completely puzzled here.
edit: this is fixed. see solution HERE
clubtech said:
i am at a total loss here.
I was on CM7 with the stock AT&T radio and HSUPA was working just fine.
I then tried to flash another radio (The Telus one) and i lost HSUPA.
I checked the build.prop and it is still showing that HSUPA is enabled.
I tried flashing back to the AT&T stock radio and HSUPA is STILL disabled...
Anyone know how to re-enable this?
I am completely puzzled here.
Click to expand...
Click to collapse
Try flashing a different rom and see if that will work. I would try stock rooted.
Thanks but there has to be another way.
I font understand why flashing a radio (Telus, i even tried a euro radio), would disabled HSUPA from nowhere and the radio is completely ignoring the build.prop file which has HSUPA enabled.
By searching i saw another user had this problem but no solution was posted.
I had to ruu to stock and rerun the hack kit.
Sent from my Desire HD using XDA Premium App
id10terrordfw said:
I had to ruu to stock and rerun the hack kit.
Sent from my Desire HD using XDA Premium App
Click to expand...
Click to collapse
THIS!!!!
I had to do the same. I searched and tried everything. I am afraid the only way is to reflash to stock and start all over again. And don't flash any other radios. I have read so many radio threads looking for the solution and most everybody I see worldwide is getting the best results with the stock AT&T radio.
id10terrordfw said:
I had to ruu to stock and rerun the hack kit.
Sent from my Desire HD using XDA Premium App
Click to expand...
Click to collapse
I guess that's what i'll have to do.
Is there a specific way i need to flash the radio in order no to lose HSUPA?
I simply used fastboot.
I do see other people on this forum who successfully flashed a different radio.
How did they do it?
There is no better radio for the inspire than the stock one. It has no hsupa limitations built in or nonspecific kernel issues, unlike the captivate. Don't flash any other radios, simple solution.
Sent from my Desire HD using XDA Premium App
Is there a way to check which radio we have? What is the identifier of stock radio?
Not sure exactly what happens but something gets screwed up somewhere.
Originally I used the Hackerize kit and flashed the original radio. Instead of flashing a Sense rom, I went straight to CM7. Everything was perfect except I did not have HSUPA no matter what I tried. I tried multiple radios and editing build.prop. Nothing worked.
This second time, I used Hackerize again. This time I took the extra steps to flash one of attn1s cooked roms. I booted that and made sure I had HSUPA before moving forward. Then I installed CM7 again and now I have HSUPA. My uploads are faster than my downloads in my area.
OK here is the deal:
1) I RUU back to stock
2) Ran the hack kit again except for the last step i never flashed back to the at&t radio as this is what is causing the problem.
3) I then tested by flashing like 4 different radios (NONE FROM AT&T) and never lost HSUPA again.i flashed 3 euro radio and 1 from Telus both on euro stock firmware and CM7.
There is something with the at&t radio that once you flash it - something gets messed up when you flash another radio.
clubtech said:
OK here is the deal:
1) I RUU back to stock
2) Ran the hack kit again except for the last step i never flashed back to the at&t radio as this is what is causing the problem.
3) I then tested by flashing like 4 different radios (NONE FROM AT&T) and never lost HSUPA again.i flashed 3 euro radio and 1 from Telus both on euro stock firmware and CM7.
There is something with the at&t radio that once you flash it - something gets messed up when you flash another radio.
Click to expand...
Click to collapse
I've flashed the stock radio and the M2 radio back and forth and back. I've never had problems with HSUPA. I just did a speedtest to make sure because I'm back on stock radio and it is 1542down/1347up.
The stock radio sounds HORRIBLE... there isnt a better way to increase call quality???? Everything sounds so raspy.
psufan5 said:
The stock radio sounds HORRIBLE... there isnt a better way to increase call quality???? Everything sounds so raspy.
Click to expand...
Click to collapse
Is the audio quality in the radio? I thought it was in the rom. I would have guessed reception quality would be in the radio. Related but not the same
Sent from my Inspire using xda app
dayamn im in this same boat...i flashed the telys radio over the stock and lost my speeds...i get beret reception with the telus radio...so the only way to get my speeds back its to un root and start over?
Sent with my CM7 Inspire
clubtech said:
OK here is the deal:
1) I RUU back to stock
2) Ran the hack kit again except for the last step i never flashed back to the at&t radio as this is what is causing the problem.
3) I then tested by flashing like 4 different radios (NONE FROM AT&T) and never lost HSUPA again.i flashed 3 euro radio and 1 from Telus both on euro stock firmware and CM7.
There is something with the at&t radio that once you flash it - something gets messed up when you flash another radio.
Click to expand...
Click to collapse
Before you flashed back to stock, did you flash the radio back to the stck ATT radio or when I flash back to the stock ruu, it changes the radio back to the ATT radio?
Sent from my Desire HD using XDA App
Thanks man! This solves my problem, the only thing is all I did was open the hacker tools and pull out the down graded radio.img and flash it then let it reboot fully then just flash whatever radio to want and you get hsupa again on the modem if your choice. Hope this helps someone.
Sent from my Desire HD using Tapatalk
Clienterror said:
Thanks man! This solves my problem, the only thing is all I did was open the hacker tools and pull out the down graded radio.img and flash it then let it reboot fully then just flash whatever radio to want and you get hsupa again on the modem if your choice. Hope this helps someone.
Sent from my Desire HD using Tapatalk
Click to expand...
Click to collapse
When you guys get HSUPA back, how do you know? Are you checking Menu>Settings>About Phone>Network>Mobile network type?
I've tried everything but this to get HSUPA and I can never get HSUPA to show as the network type. I'm nervous about flashing a new radio because it sounds like I need Eng S-Off to flash a radio and it seems there is a greater risk of bricking my phone if I screw it up than just with the radio s-off.
Clienterror said:
Thanks man! This solves my problem, the only thing is all I did was open the hacker tools and pull out the down graded radio.img and flash it then let it reboot fully then just flash whatever radio to want and you get hsupa again on the modem if your choice. Hope this helps someone.
Sent from my Desire HD using Tapatalk
Click to expand...
Click to collapse
Awesome, im gonna try that...
IsraelR said:
When you guys get HSUPA back, how do you know? Are you checking Menu>Settings>About Phone>Network>Mobile network type?
I've tried everything but this to get HSUPA and I can never get HSUPA to show as the network type. I'm nervous about flashing a new radio because it sounds like I need Eng S-Off to flash a radio and it seems there is a greater risk of bricking my phone if I screw it up than just with the radio s-off.
Click to expand...
Click to collapse
How I know if I have it or not is when I run a speed test, if my average upload speeds in 3G or "H" are less than 1 mb/s, I do this by using the speedtest.net app.
Hi all,
A week ago I bought a brand new Desire S and installed latest CM 7.1 stable following the guide on cyanogemod Desire S Wiki using revolutionary 0.4pre4. Everything was smooth and nice, I flashed ROM and GAPPS and my phone is working absolutely perfectly... but there is one little problem...
I am using Desire to fetch my mails from 2 mailservers using IMAP every 30 mins. But when the phone is switching between network modes i.e. HSDPA -> EDGE or EDGE -> GSM or any other way, I am disconnected from operator network for about 10 seconds until the network mode changes and everything is fine after that, until there is another network mode switch.
This happens for me about 10 times a day, so my phone sometimes appears that It is turned off for people who want to call me. Immediately after connecting to network I get a missed call SMS from my operator.
Interesting thing is, that when I disable email fetching, disable background data transfer and disable network data, the phone works fine without "blackouts".
Can someone help me with this problem? Maybe a radio issue?
Some more info:
ROM: Cyanogenmod 7.1.0 Desire S
Recovery: Revolutionary CWM v4.0.1.4
HBOOT: 6.98.1002
Kernel: 2.6.35.14-cyanogenmod+ [email protected] #1
Radio: 20.28I.30.085AU_3805.06.02.03_M
There is a newer radio-file online.
Maybe it's solving your problem.
I'm using MIUI and never had such problems, but i'm interested in flashing CM, so please report if the problem is gone by flashing newer radio!
Which radio version are you using?
Today I am testing 2G only switch so I am on EDGE data only.
Flashing radios is safe......, but a bad radio flash will instantly brick your phone.
You are using 1.47.401.4 radio, try updating to the 2.10.401.5 one.
Thanks for reply.
Shoud I flash something else with the radio?
I have 20.4801.30.0822U_3822.10.08.04 downloaded from cmw.22aaf3.com
Another I have is ftom OTA update zip file OTA_Saga_S_HTC_Europe_2.10.401.8-1.47.401.4_release_225210fmxlt12djw1sr7y5.zip where is one radio.img in formware.zip file too - version unknown
So Which one to flash?
and if so, which method should I use to flash radio? The Android SDK one or the ZIP + Bootloader one?
MyroLM said:
Shoud I flash something else with the radio?
Click to expand...
Click to collapse
no need
MyroLM said:
I have 20.4801.30.0822U_3822.10.08.04 downloaded from cmw.22aaf3.com
Click to expand...
Click to collapse
this file is what ur looking for! check md5-checksum before flashing!
MyroLM said:
and if so, which method should I use to flash radio? The Android SDK one or the ZIP + Bootloader one?
Click to expand...
Click to collapse
Both will work, i'm using method by using bootloader normaly
Strangely I had the same issues as you on Endymion.
Then I updated radio to the latest.
It worked well.
Then I went to CM7. It was fine for a while, but now I'm losing signal with no 3G bars and its not switching automatically to 2G like it should when It has no 3G signal!
EDIT:
After really reading your post, I realise my issue is no way like yours! Yours seems really bad. Update your radio.
-------------------------------
Sent from my HTC Desire S
So, here we go with the results
I flashed 20.4801.30.0822U_3822.10.08.04, md5sum checked OK, update sucess, but phone with no signal...
I flashed 20.48.30.0822U_3822.09.08.20, md5sum checked OK, update sucess, but phone with no signal again...
I flashed 20.28I.30.085AU_3805.06.02.03 back, md5sum checked OK, update sucess, but phone with no signal again...
... what now ... ?
After each flash wiped cache and Dalvik...
in your telephone-info there is shown the new radio after every flash?
do you have removed the batterycover, because there is integrated the antenna of your device!
mouzzza said:
in your telephone-info there is shown the new radio after every flash?
Click to expand...
Click to collapse
Yes, correct number every time.
mouzzza said:
do you have removed the batterycover, because there is integrated the antenna of your device!
Click to expand...
Click to collapse
No, the cover is at its place where it should be. Somehow I did the trick and I am back online with 20.28I.30.085AU_3805.06.02.03 on 2G only for now.
I read somwhere in the forum that ENG HBOOT is required for new radios... Are you sure I dont need to flash eng hboot it before new radio ??
MyroLM said:
Somehow I did the trick and I am back online with 20.28I.30.085AU_3805.06.02.03 on 2G only for now
Click to expand...
Click to collapse
in your area 3g is actually available?
may it helps to go outside, to find your net for the first time!
did you set an accesspoint for 3g?
may you have to set automatic settings, rather than 3g/2g-only?!
MyroLM said:
I read somwhere in the forum that ENG HBOOT is required for new radios... Are you sure I dont need to flash eng hboot it before new radio ??
Click to expand...
Click to collapse
using same hboot as you, never had problems on flashing radio-files!
yes, in my area there is 3g, when I turn off 2g only switch there is a problem described in my first post, so i am on 2g for now just to keep phone connected to network.
main problem is when i am driving and the phone is switching network modes.
so I give 20.4801.30.0822U_3822.10.08.04 today another chance, try to flash if again.
but i am woried about stucking on HTC logo after flash :-( and brick it.
MyroLM said:
but i am woried about stucking on HTC logo after flash :-( and brick it.
Click to expand...
Click to collapse
i already had the problem for several times, and i also pulled out the battery (you shouldn't do that)!
only had to boot into bootloader, start recovery, wipe all partitions, flash rom and was having fun again with my device
this thread could help you, if really stuck on HTC logo
For your real problem on loosing the signal, did you ever tried out using actual stock rom, or another custom one like MIUI?
i used MIUI from 2010-08 till yesterday, now trying out CM7.1 for some days
I have the same or a very similar problem. I have the stock rom.
I already had 3 different desire s motherboard's and 2 different display's.
The first Desire S i had, with android 2.3.3, had a excellent signal. Due some problems i had, the phone bricked and had to go to HTC to repair.
HTC replaced the motherboard and update the version of the android to 2.3.5 and ever since the signal caption, the signal switch was working very bad.
The phone went to a second repair because of this, new phone, and again with android 2.3.5. The problems persisted.
I also tested with different SIM cards, from different mobile operators.
So, my conclusion is either android 2.3.5 or this new versions of Desire S have problems with signal caption and signal switch.
So as you, i need some help with this issue!
mouzzza said:
i already had the problem for several times, and i also pulled out the battery (you shouldn't do that)!
only had to boot into bootloader, start recovery, wipe all partitions, flash rom and was having fun again with my device
this thread could help you, if really stuck on HTC logo
For your real problem on loosing the signal, did you ever tried out using actual stock rom, or another custom one like MIUI?
i used MIUI from 2010-08 till yesterday, now trying out CM7.1 for some days
Click to expand...
Click to collapse
But when I reboot to recovery it will flash the radio again I think.
i hate stock roms, and dont like MIUI design That is why I am using Cyanogen
Anyway if I use 2G only switch, the phone is stable as rock both calls and data transfer.
EDIT: OK, flashed 20.4801.30.0822U_3822.10.08.04 sucessfully, signal OK, I will see what happens whet metwork mode switches
@Green Hawk:
give us more information about your device please, which radio you're using? Did they flash actual radion also?
@MyroLM:
report if the problem is still there or it's gone with flashing the rom
I am still testing new radio, but looks good Give me some days let you know...
Hi All,
I have a similar problem with the latest CM7.1 nightly builds (Reaper, jorgen2009). I never saw this with older CM7.1 versions, e.g. Nexx version, ICS, MIUI oder Endymion.
I have WLAN on and leave my house. Phone switches to 2G/3G..., so far so good. When I return home, The WLan sign in the status bar appears again, everything seems to be fine, but I have no connection. I get no data via WLan until I swicth WLan off and on again.
Radio is the latest from 2.10.401.5.
Best Regards
Wrapp
Had similar problems, upgrading to the latest radio helped. I got stuck on the HTC screen and I went through flashing RUU's and unlocking bootloaders back and forth... when the only thing that needs to be done is to wipe the cache.
Learned a lot about bootloaders though. But my warranty got void because i did the htcdev unlock... (Sorry for OT)
Hello every one,
So my question is does any one know what the suggested radio for a Sensation on CM9 would be? I just rooted my Sensation about a month ago and have tried a few different roms, most recently Android revolution HD and now CM9 rc1. So far I love CM9 and plan to stick with it for a while but I feel like I'm not getting the best data reception. It seems like I drop from H(4g) down to 3g and back up again quite often in areas where I had fairly reliable service before. I've done some google searches and searched the forums here as well as CM's forums and can't seem to find a recommended radio file.I'm no longer on a stock radio since Android Revolution suggested a different one. Suggestions? Thanks for the help.
The reason you won't see a recommended radio file is because what works say for me might not work in the areas you live in. So radio is something you will have to experiment with to find your correct radio with matching ril file.something that works well in YOUR area. This is why people can not recommend a great combination for you. You will have to find what works best in your Area. When you flash the radio don't forget the matching ril file that goes with it ok. So do some experiments and see what works best for YOU. You flash the radio like any other pg58img file from bootloader then delete the file Afterward or it can prevent you from going to recovery. The ril is flashed like a Rom. Hope this helps you and answered your questions. So you alone must find what combo works best in your area. Best wishes to you.
Sent from my HTC Sensation 4G using xda premium
Ok, so using what you said, I stumbled into THIS post and started rereading(I had actually looked at this before but didn't "get it"). I see that some of these are posted for certain countries. Is there a way to tell which ones are for tmobile 4g in the USA? Is anything NOT listed for another country assumed to be from the USA? Is there another list of radios/rils I should be starting with? Does country of origin actually matter at all?
If you scroll down you will see a link to ICS mirror on that same page. It has several generic ics radios , those are generic so I believe they will work with ics. I'm T-Mobile and I used the newest radio on that page and it works great! I would NOT use a radio labelled for a different country. For me I kept on the safe side and used the ics radios. The link is just before the gingerbread radios start. The name of the contributor is written in blue. That link will take you to ICS radio/ril mirrors. They work great for ics. Find the combo that works best for you and your area.
Best wishes.
Sent from my HTC Sensation 4G using xda premium
So I downloaded, checked md5 and flashed a new radio. Now my ROM wont load. I can still get into recovery but it wont load CM9. Suggestions?
You have to find a radio and matching RIL file that is working for your area. Did you use the generic ics radio file WITH matching RIL file? Each radio has a matching RIL file that goes with it?
You install both. Then see which combo works best for your area. In my case I used the newest radio/ril combo for ics. It is working well in my area .
Sent from my HTC Sensation 4G using xda premium
I did use matching files, but it wouldn't boot. I ended up reloading stock tmouse firmware and re-flashing CM9. Ill have to try again tonight since I cant get away with any more while I'm at work.
Ok I'm glad you got it working! Best wishes!
Sent from my HTC Sensation 4G using xda premium
caldavien said:
So I downloaded, checked md5 and flashed a new radio. Now my ROM wont load. I can still get into recovery but it wont load CM9. Suggestions?
Click to expand...
Click to collapse
Just as an FYI - After you flash new firmware, you need to go into recovery and wipe Cache, or wipe both cache and delvik cache. Otherwise, you will never get past the cm9 boot logo.
I learned this the hard way
idtheftvictim said:
Just as an FYI - After you flash new firmware, you need to go into recovery and wipe Cache, or wipe both cache and delvik cache. Otherwise, you will never get past the cm9 boot logo.
I learned this the hard way
Click to expand...
Click to collapse
Doh! Did not know that, and I didnt wipe it until I tried flashing a new Rom. Wonder if that would have fixed it right off.
Hi all, kind of a newbie, but I've been rooting phones for a few years and have never had this issue. I wanted to upgrade my ROM to Maximus HD 10 and that was a big mistake because it involved going to SuperCID and S-Off. I was successful with both, but I ended up uninstalling due to not getting 3G/4G. Well, plenty of uninstalling and trying new ROMS and still I am left with 2G only. I have flashed the latest T-Mobile US Radio but it doesn't seem to do anything. I'm thinking it is a firmware issue, so I was wondering if there is a firmware I need to flash and do I need to fastboot flash it or recovery flash it? I am tempted to call T-Mobile and just order a new phone in the first place, but I would really like to have 3G/4G back. What firmware do I need and also does installing a new RUU overwrite the CID, firmware, and radio? I would love to back to the T-Mobile CID and the stock rom. Please help, thanks!!!
Keep soff and flash tmob ruu. All ruu contains firmware.zip, so if you flash tmob ruu you will downgrade your hboot and radio. Also make sure you'll wipe sd card from bootloader after ruu.
Sent from my HTC One S
hitzradio said:
Hi all, kind of a newbie, but I've been rooting phones for a few years and have never had this issue. I wanted to upgrade my ROM to Maximus HD 10 and that was a big mistake because it involved going to SuperCID and S-Off. I was successful with both, but I ended up uninstalling due to not getting 3G/4G. Well, plenty of uninstalling and trying new ROMS and still I am left with 2G only. I have flashed the latest T-Mobile US Radio but it doesn't seem to do anything. I'm thinking it is a firmware issue, so I was wondering if there is a firmware I need to flash and do I need to fastboot flash it or recovery flash it? I am tempted to call T-Mobile and just order a new phone in the first place, but I would really like to have 3G/4G back. What firmware do I need and also does installing a new RUU overwrite the CID, firmware, and radio? I would love to back to the T-Mobile CID and the stock rom. Please help, thanks!!!
Click to expand...
Click to collapse
should have searched and read some threads before uninstalling maximusHD. Tons of folks, myself included, had 3G/4G issues after installing MaximusHD. All fixed now.
rgrpark said:
should have searched and read some threads before uninstalling maximusHD. Tons of folks, myself included, had 3G/4G issues after installing MaximusHD. All fixed now.
Click to expand...
Click to collapse
I have drop signal issues, 3g and 4g seems normal but lose complete signal constantly.
i had home button issue when signal drops from 3g to 2g. home button activates itself sometimes when browsing internet and often drop action to homescreen. that must be radio related. and sometimes stock browser loose connection while chrome works. got tired of these things and everything all working perfectly when going back to Viper roms. any ideas ?
Sent from my HTC One S using Tapatalk 4