Hello,
Touch screen glass was broken, due to my phone fallen on the ground. The LCD was still working perfectly so i've ordered a new genuine digitizer for my HTC Z710E.
After replacing it my GSM does nothing . When charging i see the charging light lighting up in red or either green when full, but besides that i won't do anything. I disassemblied the phone again twice, reconnect all the connectors and still nothing. Sometimes my phone vibrates and sometimes when i push the power button the charging light disappears but that are the only signs of living.
Is this a common failure after replacing the digitizer? Did i overlook something?
Hopefully you guys can help me out.
Thanks in advance!
If the LCD ribbon cable is, in fact, getting a good connection then I would probably lean towards the lcd itself having been damaged during the install. Due to the construction of the sensation, it can be difficult removing the lcd without damaging it even for an experienced tech like myself.
What I would suggest would be to go ahead and order a new lcd. This would also be a good time to double check that the part number on the new digitizer's ribbon cable matches that of the broken digitizer you removed, as the incorrect part will lag when the screen is turned on at best and will not work at all at worst. As far as I know, the sensation and kindle fire are the only devices like this where you will have slightly different parts even within the same model and region.
Duck Norris said:
If the LCD ribbon cable is, in fact, getting a good connection then I would probably lean towards the lcd itself having been damaged during the install. Due to the construction of the sensation, it can be difficult removing the lcd without damaging it even for an experienced tech like myself.
What I would suggest would be to go ahead and order a new lcd. This would also be a good time to double check that the part number on the new digitizer's ribbon cable matches that of the broken digitizer you removed, as the incorrect part will lag when the screen is turned on at best and will not work at all at worst. As far as I know, the sensation and kindle fire are the only devices like this where you will have slightly different parts even within the same model and region.
Click to expand...
Click to collapse
Hmm i already thought so . I did it really really careful, but despite that it broke.
Time for getting another phone. Don't have much money now, but i shall see what's for sale
So my photon Q is rather old. Shocking I'm sure. Recently the screen has started behaving very oddly. Flickers, sensitivity is weird, blacks out etc..
I thought perhaps flex ribbon due to keyboard sliding and closing but now I think may be digitizer or the lcd. I"m leaning towards digitizer becasue when it does work it looks perfectly clear. But there will be the one time i push the power to check if I have anything and nothing happens. Reset it and can see the screen wants to do something but can't decide what. Reset over and over and eventually boots up fine.
Digitizer?
Thanks for any info.
Anybody able to chime in
Flickering screen can't have anything to do with the digitizer. The digitizer is just there for input.
It could be that the connector is a bit loose on the mainboard. The way the Photon is designed I wouldn't think it's the ribbon. I could be, but very unlikely. Anyway it's worth looking into the connectors and just to be sure the ribbon as well. But that would take a full dismantle. The connector is just 5 minutes work.
Next time try booting into recovery. If that goes well (and regular boot not) i'm pretty sure it's a hardware problem (GPU).
Die Bruine said:
Flickering screen can't have anything to do with the digitizer. The digitizer is just there for input.
It could be that the connector is a bit loose on the mainboard. The way the Photon is designed I wouldn't think it's the ribbon. I could be, but very unlikely. Anyway it's worth looking into the connectors and just to be sure the ribbon as well. But that would take a full dismantle. The connector is just 5 minutes work.
Next time try booting into recovery. If that goes well (and regular boot not) i'm pretty sure it's a hardware problem (GPU).
Click to expand...
Click to collapse
When boot in any mode Ican't see anything.. A fading circle of grey lines runs vertically down the front. Sometimes after many reboots it fixes itself though. Good to know not digitizer. So take apart and check ribbon and maybe replace LCD likely?
I wonder if it is possible to simply replace the LCD if it's defective or if you have to replace the whole LCD-digitizer-speaker-etc set (which is expensive).
Loader009 said:
I wonder if it is possible to simply replace the LCD if it's defective or if you have to replace the whole LCD-digitizer-speaker-etc set (which is expensive).
Click to expand...
Click to collapse
I ordered a replacement lcd screen so will find out. I also ordered the digitizer and flex cable.
So i'm thinking it may be more hardware involved than screen inolved. When it does work everything is usable and it works fine. This is only about 10% of the time at this point. Otherwise it boots up to show some vertical lines traveling down the middle of the screen but only in a circle in the middle of the screen that fades as it gets close to the edges. I'll try taking apart tomorrow night to see if ribbon and what not looks ok. But so far i've invested about $70 into parts and i'm thinkin about just snagging an S5 for $100. I will miss the keyboard though although I can hope that like the s3 and s4, the s5 will get a keyboard attachment. Thoughts?
If I remember correctly the LCD comes with the ribbon and camera connected. The digitizer is connected via a ribbon to a board in the top of the front panel. You could try to disable the pin. When the phone doesn't seem to work, reboot and try calling yourself. If it rings, there's something wrong with the screen and not the phone.
If there was something seriously wrong with the phone, it wouldn't boot. But that's just me guessing/assuming.
My daughter's Photon has had a digitzer replacement twice. And it looks like it's been used to play football. But that one still rocks. No quirks or any strange behavior for that matter.
What I'm trying to say is that the Photon is a decent piece of hardware. A family of four, we all have a Photon. Three of which have had their digitizer replaced and one an LCD (scratched it when replacing digitizer).
I swapped my Razr HD for an Z2. It was time for a new corporate phone. So that, and the camera, is the reason why I went for a Z2. My options were 930/G3/S5/Z2. S5 is not my cup of tea. The G3 has no ruggedness whatsoever. The 930, apart from WP maybe I should have went for it.
So it came down to the Z2. To be honest I'm looking to trade it when the Z3 compact arrives. We'll see.
@Loader009
Digitizer is a part, board for speaker is a part, the speaker itself is a part (adhesive, watch out, btw 100% the same as Droid4), and the LCD is a part on it's own.
Going to open up my phone tonight after work. I was bored and was just playing with the keyboard sliding it open and closed a bunch and now the screen looks perfectly clear.. although sometimes it will still black out and I have to reboot it a few times to get it back. I feel its more a connection inside like you stated earlier. I love my Photon and really don't want to have to get a non slider phone. New phone's are so friggin huge lol.
The good thing is, the PQ has gotten pretty cheap, so you might want to get a used one at ebay if the part to replace is too expensive.
flickering screen (backlight) is not lcd problem.
for 70% is it problem on mainboard - backlight ic. This problem is caused by using unoriginal charger.
and 30% flex problem
I had my screen become un-responsive etc, it was due to a crack in the ribbon. Swapped it out & all ok.
Easier to swap the whole screen assy than to change the ribbon, but depends on what spares you have/can get.
You'd need to have a good look at the ribbon for any damage.
Sent from my SIM-modded Photon Q
Ok well here is my issue. While replacing the LCD assembly on my one plus one I managed to rip off the metal connectors(I believe they are called pogo sticks) on the logic board that make contact with the antenna's on the back cover. I ripped the ones that control the WiFi/Bluetooth and also the GPS one. I was trying to figure out how to fix this since when trying to soder them back on there was nothing they could be soldered to. I'm basically left with the empty spots on the PCB board where they are supposed to go. While looking at the logic board I saw that there are a couple of pigtail looking connectors on it that don't have anything particularly connected to them. I was wondering if I could use those to repair my connection issues. Or of any of you have any advice to give thank you for all your help ^_^
I have a second generation Shield Tablet K1 that I purchased in December 2015.* The tablet was knocked off a counter and landed face down on travertine tile. The glass/digitizer did remarkably well considering but still had a large crack going down the middle of the screen. The tablet still worked in all regards* and I used it with no issues for 6 weeks. I purchased an NVIDIA SHIELD TABLET P1761W OEM LCD TOUCHSCREEN DIGITIZER on eBay.
I had the new digitizer installed locally at a phone/tablet repair shop. The shop called me and told me the tablet was ready for pickup but there were some issues with certain areas of touch screen not working. Basically the upper half of the touch screen works fine and the lower half does not work at all. As far as I can tell the area that works is exactly 50% of the screen. Just trying to do the basics on it right now is a pain as I have to rotate the tablet 180 degrees every few seconds in order to be able to touch a specific key or an app. Of course the shop won't warranty the work because I didn't buy the digitizer from them. What I'm wondering is if anyone can suggest a specific ribbon wire that may need to be replaced or simply checked to make sure the connection is good on it? Should I replace the touch screen controller?
Any suggestions will be much appreciated.
well, if you don't want to open it up yourself, maybe try getting another, more "able" person to look at it. Check reviews and the company, see if it's a known issue, it just might be a bad buy. I'm bet Ebay will do something about it if you contact them, also try contacting the supplier
I don't mind opening it up. I was hoping for some insight as to what to look for. I can swap out the Touchscreen Controller from my original digitizer and see if that corrects the issue. I thought with such a specific issue (only the upper half of the touchscreen working) someone could tell me yes, with that symptom you need to replace your Touchscreen Controller or that would only happen if XYZ ribbon weren't connected.
Maybe the touch screen is defect?
You're screwed. The repair shop tore the digitizer flex cable. The flex cable has no room to flex on an angle, so the cable just rips.
I just did this myself, and was looking around for a replacement when I found this thread. I couldn't find the problem until after I ripped it more; Now only the top left corner works.
I'm just buying a new one, because the problem I initially opened it to fix needs a heat gun, which I don't have.
Good luck
I have two G920P's. My main has a broken digitizer and the other one is has a functioning one. Because swapping screens is damn near impossible, can I just swap mobo's?