Related
Hi sensation forum...
I am new to sensation, but not new to android or HTC, as i have 4 different phones with custom firmware on them...
But the sensation give me a lot of problems for some reason...
I have tried ARHD 5.0.2 and Insert Coin 4.0.4, i have also tried Virtuous Inquisition v1.3.0 and HyperSensation CM7.1 v1.2.
The last one is not even ICS based...
All of them give me random reboot cycles...
I have tried 3 different radios also...
Nothing have helped me so far...
I still have a lot of random reboots...
(about every 2-10 min)
When i flash the firmware i use ARHD´s super delete script, but to be shure, i also format everything from within Recovery...
What more can i do here ??
Pleace,if your phone is stable, can you tell me exactly what rom/radio/kernal/ril you use...
My phone was rock stable with factory firmware....
Hey,
When installing roms on the sensation, make sure you follow the guides in the particular thread. It is also important to match recommended radios and rils that go with the specific rom. Make sure you are S-off and cid 11111111. When you are switching roms, you should only have to run the superwipe script, it will set all the partitions for you so that you can flash the rom you choose. Also, before you install ICS, it is recommended that you superwipe BEFORE installing the actual rom to prevent unwanted isssues. Before you do anything else, give me a rundown on what you are currently running.
ROM:
Radio:
RIL:
Kernel:
MODS:
pshdo said:
Hi sensation forum...
I am new to sensation, but not new to android or HTC, as i have 4 different phones with custom firmware on them...
But the sensation give me a lot of problems for some reason...
I have tried ARHD 5.0.2 and Insert Coin 4.0.4, i have also tried Virtuous Inquisition v1.3.0 and HyperSensation CM7.1 v1.2.
The last one is not even ICS based...
All of them give me random reboot cycles...
I have tried 3 different radios also...
Nothing have helped me so far...
I still have a lot of random reboots...
(about every 2-10 min)
When i flash the firmware i use ARHD´s super delete script, but to be shure, i also format everything from within Recovery...
What more can i do here ??
Pleace,if your phone is stable, can you tell me exactly what rom/radio/kernal/ril you use...
My phone was rock stable with factory firmware....
Click to expand...
Click to collapse
I have exactly this issue.
I installed ICS Revolution. I had successfully got S-OFF, Installed ClockWork Recovery (updated to latest version), permanently Rooted & obtained SuperCID. I updated radio as recommnded by mike1986 in the ICS post, and wiped the phone with Revolution Super_wipe_Sensation first.
It seemed to run fine apart from Doplhin HD which refused to run properly (so switched to Opera Mobile). However I started to get random reboots.
After a bit I thought to try Insert Coin ICS instead.
I have noticed no real difference in performance and have the identical issue with Dophin HD (back to Opera mobile again).
However I also still have the identical random rebooting issue with this ROM. What else can I do?
maverick0729 said:
Hey,
When installing roms on the sensation, make sure you follow the guides in the particular thread.
Click to expand...
Click to collapse
Read for days on these
maverick0729 said:
It is also important to match recommended radios and rils that go with the specific rom. Make sure you are S-off and cid 11111111
Click to expand...
Click to collapse
Check
maverick0729 said:
When you are switching roms, you should only have to run the superwipe script, it will set all the partitions for you so that you can flash the rom you choose. Also, before you install ICS, it is recommended that you superwipe BEFORE installing the actual rom to prevent unwanted isssues.
Click to expand...
Click to collapse
As stated, I did that before installing Revloution's ICS. BUT I didn't do it before installing Insert Coin. Should I have?
maverick0729 said:
Before you do anything else, give me a rundown on what you are currently running.
Click to expand...
Click to collapse
ROM: Insert Coin ICS 4.0.4
Radio: 11.59.3504.00U_11.16.3504.16_M
RIL: What's that? Where do I find it?
Kernel: 3.0.13-g8085863
Any suggestions?
Did you guys flash the firmware update that is needed for the ics rom
blahbl4hblah said:
Did you guys flash the firmware update that is needed for the ics rom
Click to expand...
Click to collapse
I did that with Revolution as well as with Insert Coin this time around. Running the latest version
I'm having the same issue. Did a text book install of AHRD. Everything went super smoothly, but getting these reboots. I have tried to swipe everything, have the latest radio and recommended fw and keep getting these crashes. Not only it's driving me nuts but it makes the phone unuseable... I can't believe we're just 2 to have these problems... Isn't there some king of log we can pull to see what's causing the crash ?
---------- Post added at 08:52 AM ---------- Previous post was at 07:52 AM ----------
I suspect it has to do with processor speed that's been tweaked in these roms, but can't seem to find a way to tune it back to stock on the ICS rom...
sorry for the late reply, been busy with holiday stuff.. anyhow, make sure you are NOT installing any mods that are not compatible with the current ICS build. I have had no problems switching between ARHD 3.6.10 and ICS 5.0.2. As long as you have s-off and CID 1111111, you should be good to go. When I changed up from 3.6.10 to ICS 5.0.2, I turned off my phone, went into bootloader, selected the option for recovery, then flashed the superwipe script. After it finished flashing that, it rebooted back into recovery. Following that, I went to install from zip, flashed the updated RUU, cleared cache and dalvik, then flashed ICS 5.0.1 and the 5.0.1 to 5.0.2 update. Everything installed smooth from there.
maverick0729 said:
sorry for the late reply, been busy with holiday stuff.. anyhow, make sure you are NOT installing any mods that are not compatible with the current ICS build. I have had no problems switching between ARHD 3.6.10 and ICS 5.0.2. As long as you have s-off and CID 1111111, you should be good to go. When I changed up from 3.6.10 to ICS 5.0.2, I turned off my phone, went into bootloader, selected the option for recovery, then flashed the superwipe script. After it finished flashing that, it rebooted back into recovery. Following that, I went to install from zip, flashed the updated RUU, cleared cache and dalvik, then flashed ICS 5.0.1 and the 5.0.1 to 5.0.2 update. Everything installed smooth from there.
Click to expand...
Click to collapse
That's exactly what I did. Can't find anything different between your story and what's I did, up to when I switched to Insert Coin
I also don't think it's related to CPU speed. My phone is the XE model which ran at 1.5 Ghz on stock ROM and only did about 3 random reboots in 3 months; (now it's every couple of hours).
Sent from my HTC Sensation XE with Beats Audio Z715e using xda premium
I'm doing a full restore and then reinstall. We'll see what happens.
Levraimatt said:
I'm doing a full restore and then reinstall. We'll see what happens.
Click to expand...
Click to collapse
Good luck. Hope it helps. Let us know the outcome. My nandroid backup is corrupted so will need to do full wipe of my SD card and phone I think. Then add in a stock ROM
Sent from my HTC Sensation XE with Beats Audio Z715e using xda premium
I'm still getting the reboot on the nand backup (OrangeFR), this sucks big time. Now I'm thinking it may be due to the fw I had to install to use AHRD (PG58IMG) and the new radio. This is where I'm lost. How can I return everything to standard ? If I understand well the ROM doesn't contain those files, they are separate ?
Was thinking that my random reboots were radio or firmware related.
Strange thing is mine have stopped, and all I did was reinstall revolution ICS 5.0.1 then upgrade to 5.0.2. Didn't even wipe first. So even my apps & settings all of which I had installed & configured since I had installed Insert Coin ICS, are all still there. Haven't had a reboot since.
Sent from my HTC Sensation XE with Beats Audio using xda premium
I switched back to ARHD 3.6.9, did a factory reset+wipe, flashed radio 10.59 and all is fine, I'm somehow reluctant to try again...
I found a solution that worked for me... At last...
I am REALLY sorry that i didn´t answer here before, but i have been really bussy, and actually forgot all about it a few days....
NOW, i also thought that i had some CPU spped issue with the roms, becource i can actually get the same kind of reboot problems on my DHD when i run it over 1500 Mhz...
So i thought that i would lock my sensation to max 900 mhz, and then see what happens... NO change... Still random reboot... Strange...
I then installed a Android 2.3 rom, just to get my phone running again... STILL random reboots...
hmmm....
Now i was confused...
At last i tried to flash a different radio one more time...
I found a radio in some other sensation thread... Flashed it and now my phone works stable...
At least with Virtuos Inquisition 1.3.0... (Proberbly the 1.4.0 will also work, but i have not tried it yet...)
The Radio i had the problems with is the one from mike´s thread...
I actually don´t know why, as i have allways had great success with his roms and his releases on my DHD...
The Radio i use now is 10.58.9035.00U_10.15.9035-02_2...
But sorry, i can´t remember from what thread...
Ok, this is what i have discovered on this reboot issue...
I hope it make some sense, and that this perhaps can help other with the same problems...
Try turning your phone to recovery.Backup if you havent already....Wipe Data/Factory reset then turn the phone off....
Remove the back cover and the SDCARD.Turn the phone back on and see if it runs ok without the SDCARD, if it does reformat the sd using 4ext recovery and it will also align it.
I spoke too soon.
My phone didn't reboot for a day after I switched back to Revolution ICS 5.0.2 for about a day, then today it began doing random reboots every few minutes. I had not changed any software, just the area (which might have changed signal and frequency the cell tower uses). So I figured it was time to change firmware and radio.
I had previously (prior to installing custom ICS ROM) flashed the radio to 10.58.9035.00U_10.15.9035.02_2 as recommended by Mike1986 in the Revolution HD ICS thread, and had HBoot 1.7.1111 on my device.
I then downloaded the firmware he posted on his thread here:
http://forum.xda-developers.com/showthread.php?t=1412618
This has put the phone back to HBOOT 1.20.0000 and radio 11.15.3504.16_M
Now it's working well and no reboots yet.
Here's hoping.. time will tell.
No matter what radio or Rom combo I get random ass reboots
Super annoying. I did notice the battery goes from 100% to 10% during this reboot
I have calibrated battey. Wiped stats. I'm lost.
I have even tried a new battery. Wtf. Any ideas?
i cant even flash stock ruu I get a 171 error!!!!
Im gonna throw this phone at the f-ing wall in a min
if you flashed newest radio 11...x.x..., you have to have newest hboot also (1.20.. , i guess). otherwise, you will get random reboot. I had this issue before, and i just flashed order radio( i don't want to update hboot version). problem is solved
tritran18518 said:
if you flashed newest radio 11...x.x..., you have to have newest hboot also (1.20.. , i guess). otherwise, you will get random reboot. I had this issue before, and i just flashed order radio( i don't want to update hboot version). problem is solved
Click to expand...
Click to collapse
That's certainly consistent with my experience.
Since the changes I made as per my previous post, I've not had a single random reboot
Sent from my HTC Sensation XE with Beats Audio Z715e using xda premium
Hi all,
A week ago I bought a brand new Desire S and installed latest CM 7.1 stable following the guide on cyanogemod Desire S Wiki using revolutionary 0.4pre4. Everything was smooth and nice, I flashed ROM and GAPPS and my phone is working absolutely perfectly... but there is one little problem...
I am using Desire to fetch my mails from 2 mailservers using IMAP every 30 mins. But when the phone is switching between network modes i.e. HSDPA -> EDGE or EDGE -> GSM or any other way, I am disconnected from operator network for about 10 seconds until the network mode changes and everything is fine after that, until there is another network mode switch.
This happens for me about 10 times a day, so my phone sometimes appears that It is turned off for people who want to call me. Immediately after connecting to network I get a missed call SMS from my operator.
Interesting thing is, that when I disable email fetching, disable background data transfer and disable network data, the phone works fine without "blackouts".
Can someone help me with this problem? Maybe a radio issue?
Some more info:
ROM: Cyanogenmod 7.1.0 Desire S
Recovery: Revolutionary CWM v4.0.1.4
HBOOT: 6.98.1002
Kernel: 2.6.35.14-cyanogenmod+ [email protected] #1
Radio: 20.28I.30.085AU_3805.06.02.03_M
There is a newer radio-file online.
Maybe it's solving your problem.
I'm using MIUI and never had such problems, but i'm interested in flashing CM, so please report if the problem is gone by flashing newer radio!
Which radio version are you using?
Today I am testing 2G only switch so I am on EDGE data only.
Flashing radios is safe......, but a bad radio flash will instantly brick your phone.
You are using 1.47.401.4 radio, try updating to the 2.10.401.5 one.
Thanks for reply.
Shoud I flash something else with the radio?
I have 20.4801.30.0822U_3822.10.08.04 downloaded from cmw.22aaf3.com
Another I have is ftom OTA update zip file OTA_Saga_S_HTC_Europe_2.10.401.8-1.47.401.4_release_225210fmxlt12djw1sr7y5.zip where is one radio.img in formware.zip file too - version unknown
So Which one to flash?
and if so, which method should I use to flash radio? The Android SDK one or the ZIP + Bootloader one?
MyroLM said:
Shoud I flash something else with the radio?
Click to expand...
Click to collapse
no need
MyroLM said:
I have 20.4801.30.0822U_3822.10.08.04 downloaded from cmw.22aaf3.com
Click to expand...
Click to collapse
this file is what ur looking for! check md5-checksum before flashing!
MyroLM said:
and if so, which method should I use to flash radio? The Android SDK one or the ZIP + Bootloader one?
Click to expand...
Click to collapse
Both will work, i'm using method by using bootloader normaly
Strangely I had the same issues as you on Endymion.
Then I updated radio to the latest.
It worked well.
Then I went to CM7. It was fine for a while, but now I'm losing signal with no 3G bars and its not switching automatically to 2G like it should when It has no 3G signal!
EDIT:
After really reading your post, I realise my issue is no way like yours! Yours seems really bad. Update your radio.
-------------------------------
Sent from my HTC Desire S
So, here we go with the results
I flashed 20.4801.30.0822U_3822.10.08.04, md5sum checked OK, update sucess, but phone with no signal...
I flashed 20.48.30.0822U_3822.09.08.20, md5sum checked OK, update sucess, but phone with no signal again...
I flashed 20.28I.30.085AU_3805.06.02.03 back, md5sum checked OK, update sucess, but phone with no signal again...
... what now ... ?
After each flash wiped cache and Dalvik...
in your telephone-info there is shown the new radio after every flash?
do you have removed the batterycover, because there is integrated the antenna of your device!
mouzzza said:
in your telephone-info there is shown the new radio after every flash?
Click to expand...
Click to collapse
Yes, correct number every time.
mouzzza said:
do you have removed the batterycover, because there is integrated the antenna of your device!
Click to expand...
Click to collapse
No, the cover is at its place where it should be. Somehow I did the trick and I am back online with 20.28I.30.085AU_3805.06.02.03 on 2G only for now.
I read somwhere in the forum that ENG HBOOT is required for new radios... Are you sure I dont need to flash eng hboot it before new radio ??
MyroLM said:
Somehow I did the trick and I am back online with 20.28I.30.085AU_3805.06.02.03 on 2G only for now
Click to expand...
Click to collapse
in your area 3g is actually available?
may it helps to go outside, to find your net for the first time!
did you set an accesspoint for 3g?
may you have to set automatic settings, rather than 3g/2g-only?!
MyroLM said:
I read somwhere in the forum that ENG HBOOT is required for new radios... Are you sure I dont need to flash eng hboot it before new radio ??
Click to expand...
Click to collapse
using same hboot as you, never had problems on flashing radio-files!
yes, in my area there is 3g, when I turn off 2g only switch there is a problem described in my first post, so i am on 2g for now just to keep phone connected to network.
main problem is when i am driving and the phone is switching network modes.
so I give 20.4801.30.0822U_3822.10.08.04 today another chance, try to flash if again.
but i am woried about stucking on HTC logo after flash :-( and brick it.
MyroLM said:
but i am woried about stucking on HTC logo after flash :-( and brick it.
Click to expand...
Click to collapse
i already had the problem for several times, and i also pulled out the battery (you shouldn't do that)!
only had to boot into bootloader, start recovery, wipe all partitions, flash rom and was having fun again with my device
this thread could help you, if really stuck on HTC logo
For your real problem on loosing the signal, did you ever tried out using actual stock rom, or another custom one like MIUI?
i used MIUI from 2010-08 till yesterday, now trying out CM7.1 for some days
I have the same or a very similar problem. I have the stock rom.
I already had 3 different desire s motherboard's and 2 different display's.
The first Desire S i had, with android 2.3.3, had a excellent signal. Due some problems i had, the phone bricked and had to go to HTC to repair.
HTC replaced the motherboard and update the version of the android to 2.3.5 and ever since the signal caption, the signal switch was working very bad.
The phone went to a second repair because of this, new phone, and again with android 2.3.5. The problems persisted.
I also tested with different SIM cards, from different mobile operators.
So, my conclusion is either android 2.3.5 or this new versions of Desire S have problems with signal caption and signal switch.
So as you, i need some help with this issue!
mouzzza said:
i already had the problem for several times, and i also pulled out the battery (you shouldn't do that)!
only had to boot into bootloader, start recovery, wipe all partitions, flash rom and was having fun again with my device
this thread could help you, if really stuck on HTC logo
For your real problem on loosing the signal, did you ever tried out using actual stock rom, or another custom one like MIUI?
i used MIUI from 2010-08 till yesterday, now trying out CM7.1 for some days
Click to expand...
Click to collapse
But when I reboot to recovery it will flash the radio again I think.
i hate stock roms, and dont like MIUI design That is why I am using Cyanogen
Anyway if I use 2G only switch, the phone is stable as rock both calls and data transfer.
EDIT: OK, flashed 20.4801.30.0822U_3822.10.08.04 sucessfully, signal OK, I will see what happens whet metwork mode switches
@Green Hawk:
give us more information about your device please, which radio you're using? Did they flash actual radion also?
@MyroLM:
report if the problem is still there or it's gone with flashing the rom
I am still testing new radio, but looks good Give me some days let you know...
Hi All,
I have a similar problem with the latest CM7.1 nightly builds (Reaper, jorgen2009). I never saw this with older CM7.1 versions, e.g. Nexx version, ICS, MIUI oder Endymion.
I have WLAN on and leave my house. Phone switches to 2G/3G..., so far so good. When I return home, The WLan sign in the status bar appears again, everything seems to be fine, but I have no connection. I get no data via WLan until I swicth WLan off and on again.
Radio is the latest from 2.10.401.5.
Best Regards
Wrapp
Had similar problems, upgrading to the latest radio helped. I got stuck on the HTC screen and I went through flashing RUU's and unlocking bootloaders back and forth... when the only thing that needs to be done is to wipe the cache.
Learned a lot about bootloaders though. But my warranty got void because i did the htcdev unlock... (Sorry for OT)
Ok, so here is the story of how I screwed up. And the situation
1) I was running firmware 3.33 with viper ... everything was ok
2) Decided to try bruce's CM10... everything ok
3) Copule of days later I decided to flash the old RIL I was using with CM9 + firmware 3.33 and used to work ok.... big fail. Radio stoped working
4 )full wipe, flashed firmware 3.32 and Bruce's latest build... the phone booted ok, but still radio wasn't working
5) full wipe, flashed firmware 3.33 and Bruce's latest build... the phone booted ok, but still radio wasn't working
6) full wipe, flashed viper .... I intermittently get data but no phone signal... WTF?
Before someone asks... yes.. I was always veryfing checksums when flashing different firmwares.
Any Advice?
Is it possible that I broke something? Maybe the SIM card?
what do you think guys? Please Help!
have the same problem, was running ARHD with no problems, then using bruce CM10.
I didnt like it, so i changed back to ARHD.
Now i flashed Viper-Rom, and my Radio is broken
Try flashing a generic ics radio and ril this should help restore your data. I lost data once by flashing a recommended radio for a Rom I was running and I restored my data by flashing a generic ics radio and ril. Fixed this issue for me. You might want to give it a try .I think it will help. Best of luck.
Sent from my Sensation Z710e using xda premium
Could i just flash 3.32 and then flash Viper?
what is "ril"?
*#*#4636#*#* on dialer then phone information and verify what network mode is it on (it should be GSM/WCDMA auto)
dont know what happend, i flahed ARHD, but did a superwipe before.
Now the Radio works. only have to get wifi better, is there a fix for that?
Hi all;
First of all I want to say that I already spent a week or so reading different guides, flashing radios and kernels trying to fix this issue.
My problem is that the WiFi is stuck on Obtaining IP and can't connect to my home network. This happens on all ROMs except ViperS.
This issue started for me after flashing ViperS 1.5.2, before that I was using ARHD 6.8.0 without any Wifi errors.
About a week ago I decided to leave the ViperS 1.6.0 because of a low batery life, but when I switched back to ARHD 6.8.0 I got the wifi errors.
I tried stock roms, ARHD, different RUUs, reflashing radio and firmware, custom kernels without any luck...
The only setup that the Wifi worked (except the ViperS) was after installing RUU_Pyramid_LE_HTC_Europe_1.73.401.4, but when I installed the OTA that upgrades it to 3.32.401.105, the wifi errors came back.
ViperS changelog says that it messes with the WiFi to force 801.11n or something...
Please help me, I just want to go to the previous state, before installing ViperS.
nmaxim said:
Hi all;
First of all I want to say that I already spent a week or so reading different guides, flashing radios and kernels trying to fix this issue.
My problem is that the WiFi is stuck on Obtaining IP and can't connect to my home network. This happens on all ROMs except ViperS.
This issue started for me after flashing ViperS 1.5.2, before that I was using ARHD 6.8.0 without any Wifi errors.
About a week ago I decided to leave the ViperS 1.6.0 because of a low batery life, but when I switched back to ARHD 6.8.0 I got the wifi errors.
I tried stock roms, ARHD, different RUUs, reflashing radio and firmware, custom kernels without any luck...
The only setup that the Wifi worked (except the ViperS) was after installing RUU_Pyramid_LE_HTC_Europe_1.73.401.4, but when I installed the OTA that upgrades it to 3.32.401.105, the wifi errors came back.
ViperS changelog says that it messes with the WiFi to force 801.11n or something...
Please help me, I just want to go to the previous state, before installing ViperS.
Click to expand...
Click to collapse
Hi,
Have you tried the RUU,but then, do not let it update.
Just use the Universal firmware update from HERE
malybru said:
Hi,
Have you tried the RUU,but then, do not let it update.
Just use the Universal firmware update from HERE
Click to expand...
Click to collapse
I love you my friend!
It worked!
Hey guys,
I did some searching and didn't see an answer to my specific problem so I figured I would go ahead and ask.
A few weeks ago I installed CM 10.1.2 using TWRP. After installing I was having signal, battery and bluetooth issues.
I did some research and found that I needed to flash a new radio I727UCMC1. I did that according to the protocols (without cable in, twice) and still had the same connectivity issues.
Since then I have tried a few different ROMs going back to ICS and JB but am still having the same issues. I am currently using SilmBean 4.3 beta 4- Weekly-427.
Does anyone have any suggestions as to what I should do to fix the radio problems I am having?
Thanks!
cinematographer said:
Hey guys,
I did some searching and didn't see an answer to my specific problem so I figured I would go ahead and ask.
A few weeks ago I installed CM 10.1.2 using TWRP. After installing I was having signal, battery and bluetooth issues.
I did some research and found that I needed to flash a new radio I727UCMC1. I did that according to the protocols (without cable in, twice) and still had the same connectivity issues.
Since then I have tried a few different ROMs going back to ICS and JB but am still having the same issues. I am currently using SilmBean 4.3 beta 4- Weekly-427.
Does anyone have any suggestions as to what I should do to fix the radio problems I am having?
Thanks!
Click to expand...
Click to collapse
There isn't anything I can tell from what you provided. If you are claiming that you are following the threads on XDA and tutorials then you should be fine.
If you are still having problems then walk me through the steps you take assuming you are back to the stock UCMC1, did a full wipe on the stock ROM, and now you are ready do install TWRP or CMW and load up CM10.1.X.
Flashing back to stock and wiping everything solves many problems, and the UCMC1 radio will be automatically there when you install your custom recovery and custom rom. So you don't have to reflash UCMC1-radio in a case where you are coming from the stock UCMC1.