This thread is for the custom Froyo rom for the Flytouch 2. It is a port of the first Flytouch 3/Superpad 2 Froyo rom, adapted to run on the flytouch 2. I will update this post whenever a new version has been released.
This rom will only run on tablets which display a version number in the bottom-right "Infotmic" screen when first turned on.. If yours doesn't display a number there, you will need to flash firmware v2852 first, see below in FLASHING V2852
INSTALLATION
Installation is slightly different from normal releases because it requires flashing in 2 steps. Luckily, it's really easy:
1. Download bootable SD-card image and unzip. Pick an image from the RELEASES section at the end of this post.
2. Write image to an SD-card that's at least 1GB in size using Win32DiskImager:
Get Win32DiskImager here: https://launchpad.net/win32-image-writer
In Win32DiskImager: When you open it, there is a button to browse the .img file and after that, at the right of this button there is a selector for the SD-card. Select it, then click write and it's done.
When finished, take out the card.
In linux, you just unzip the file and use dd to write it to the sd-card:
Code:
dd if=/path/to/sdcard.img of=/dev/sdX # (where sdX is your scsi disk device, check dmesg)
3. Turn off tablet and put sd-card in TOP slot (between the 2 usb ports).
4. Turn on tablet. It will report that it is booting off the sd-card, and that it's flashing kernel + filesystems.
5. Take out the sd-card when the tablet asks you to do so (takes less than a minute). Put it in the OTHER sd-card slot (bottom one), and reboot the tablet by holding down the power for 10 seconds to turn it off, then press it again to turn it on.
6. You will now see the tablet booting with a *GREEN* screen. The screen will flash twice to indicate it's starting. The flashing itself will take longer than in the previous step, a few minutes. If succesful, it will automatically reboot, after which you're done and you're booting the new firmware! You'll see a different boot screen (equalizer on a black background)
7. After it has booted and you have unlocked the screen, reboot the tablet first thing! First boots in android always tend to be behave erratically. This is unrelated to this firmware and applies to all Android setups.
If step 6 fails (which is very unlikely), it will stay on the green screen and it will keep on flashing the screen. In that case, you'll have to turn it off. Most likely problem for this is a corrupt SD-card. See troubleshooting below.
Make sure to never put that sd-card back in the top-slot without erasing it first, as it will reflash your tablet!
TROUBLESHOOTING
The 'green screen' keeps flashing!
The installer will dump a text file on the root of the sd-card which you can inspect. The file is called fail_reason.txt. If no such file exists, things are seriously wrong and the tablet couldn't even properly write to the sd-card. If using another SD-card, or rewriting the SD-card doesn't help, please upload the fail_reason.txt file here.
Flashing was succesful, but the system freezes at the android animation!
For this firmware to work, you need to have a recent version of u-boot. You can tell if you have this by looking at the INFOTMIC bootscreen you see when you turn on the tablet. If the bottom right corner does not show a version number, then you don't have it.See instructions below.
FLASHING V2852
You need to flash this firmware to install a new version of u-boot. To flash this firmware, you will need to connect your tablet to your PC using an USB A-A cable, OR create a bootable SD-card.
Download firmware V2852: http://www.mediafire.com/download.php?3bkklw36b1414nd
Download and unpack IUW: http://www.mediafire.com/download.php?3572bd7zfjo0r0y
Start IUW
If you use an USB cable: Click 'Link USB' on the left, select 'easy burn' from USB Mode pulldown in the right. Connect tablet to PC with the tablet turned offf, then turn it on by pressing & holding the menu+home buttons, then pressing the power button until it turns on. Release the menu+home buttons after a few seconds. Windows should now detect a new USB device. Install the drivers that are in the iuw1.1/otg_driver directory.
If you create a bootable SD-card, Click 'boot disk' on the left instead. Select sd-card to flash on the right
Select the IUS file form the v2852 firmware under 'Choose a wrapped image'
Click 'burn' to flash the tablet or create the sd-card. If you created an sd-card, boot the tablet with the sd-card in the top-slot, between the 2 USB connections.
TODO
How to enable 3G support for USB dongles?
(**) Tested:
wifi, ethernet port
battery status works, g-sensor works
touchscreen works, including calibration
HD video playback works (I recommend Meridian player)
Market works (full), Youtube works
angry birds works ( thought I'd mention it )
The firmware has already been rooted! You can connect using adb over wifi, and type 'su' to become root. Find your IP address using the Android System Info app.
GPS confirmed
VIDEO
Video demonstrating how to flash the tablet after having created the bootable SD-card: http://www.youtube.com/watch?v=47kf4-Vbba8#t=3
RELEASES
April 24th 2011, V5: http://www.mediafire.com/?1ka7ngpi82grmfm
Added older version of YouTube (1.6.21) which works
Fix touchscreen calibration
Added LauncherPro as alternative launcher
March 2011, V4: http://www.mediafire.com/?oc1bwnq71smb09k
verandi said:
Hi everyone.
I just made a personal version of system.tar.gz, and I thought it could be usefull for someone.
Most considerable changes:
Calendar and contacts synchronization now working again.
Simple stock froyo keyboard, without chinese characters.
Replaced youtube with the old working version.
Market updated to last version (no paid apps, though.).
Default launcher replaced with launcher pro, which is considerably faster.
Removed phone and telephony settings (see below)
Other changes:
Removed stock browser, replaced with dolphin browser HD.
Removed default file explorer, replaced with File expert (first free file explorer with working root that I found).
Changed alarm clock.
Changed calculator (but has wrong visualization).
Changed music player with music mod.
Added facebook, maps (+ navigation + latitude +places), chrome to phone, google search, google reader, terminal emulator, Titanium backup, voice search. adobe reader.
Maybe I deleted some other stupid flytouch stock apps, but actually I don't remember.
Warning, notes etc...:
All apps are free apps from market.
Phone apps (Phone.apk, TelephonySettings.apk) removed for test, due to suspected battery drain (Someone said so...), so:
Phone settings don't work (gives you force close when you tap on mobile settings menu)
Don't install if you use 3g adapters, as I think you won't be able to use them.
Maybe some future workarounds for paid apps on market won't work.
App2sd doesn't work. (Didn't even work before. I think there's some problem in the kernel with device mapper and crypto). I'll try to implement the fake app2sd that uses an ext partition on sd.
This is just a personal versionof stargulus' system files with apps I'm used to have on my phone, so maybe it won't fit you.
How to install:
First important step: boot in recovery mode (back + home +power until you get in recovery menu), and wipe cache and data. This must be done. It also helps to have stragulus' calibration file installed correctly.
Prepare the sd as described in the first post of this thread using the last Stragulus' sdcard image (v4, See link in this post).
Go to "stage2" directory and replace system.tar.gz and system.tar.gz.md5 with the downloaded ones.
Flash.
The first boot will be quite long, but it's normal.
While using the flytouch for the first time, it will probably lag and hang. Just reboot and it won't happen anymore.
File link: http://www.multiupload.com/Z9CONJVPQO
I hope this will be usefull. Advices are welcome.
Click to expand...
Click to collapse
Cheers! I welcome custom mods of the base rom. I'm willing to add them as alternatives to the first post by linking to the introductory posts. In this case, it looks like parts of it are suitable for integrating into the base froyo rom (e.g. calendar & contact sync fix). What exactly did you do to fix those?
Wonderful, downloading now at 7.8K/sec (why sooooo slow?)
Is Google Sync fixed?
Thanks,
Barak
Later:
Well, if I add Verandi's MOD I get sync but I loose calibration option.
Still, I prefer the MOD with sync.
Thank you guys. Amazing Job !!!
1-5-2011
Please note that verandi has created a V5 mod that adds sync option without eliminating calibration.
http://forum.xda-developers.com/showpost.php?p=13343444&postcount=54
Good luck.
Your uboot - 0.6.1.2 (587) http://www.mediafire.com/?4hx8xt38vnhh22b
My uboot - 0.6.1.5 (587) http://www.mediafire.com/?bv4ixzeq34q5bi7
what's the latest?
which should I use?
EDIT:
If possible enable a swap partition to optimize tablet in ROM? (we have little RAM)
Camera have a problem. Green image in V5 (24/04/2011)
@ Stragulus
I've been waiting for
Thank you for your work
Market will not dowload
Well once again my hats off to you Straguls for a job well done I installed the version 5 rom with no issues however the Android Market still only displays the free apps and will not download and install any of the apps it states download unsuccessful any help with this matter would be greatly appreciated.
Thanks
Steve
stragulus said:
This rom will only run on tablets which display a version number in the bottom-right "Infotmic" screen when first turned on.
Click to expand...
Click to collapse
In my case loader version number is missing. But u0 is 0.6.1.2_1.4.587_OV2655 and u-boot from 2852. And all work fine.
Probably condition is flashing firmware 2852 in the tablet instead of only u0?
IMHO.
Because the firmware is full image and contained u-boot and u0. Flashing u0 need only if camera don't work with 2852 from full image. Of course, if the tablet has not been purchased already with firmware 2852 and above. Without this step you will get many reports of "fre-e-e-ezing" or "stop in android on screen" like in the previous thread.
hello
I have stitched from card Froyo V5
The tablet is loaded and asks calibration, but it does not work: (
Was 3245, but it has ceased to be loaded and I have updated on Froyo
I do not know what at me uboot how it to look? Probably to update it with sd?
jp08 said:
загружатся
Click to expand...
Click to collapse
По русски спроси. Я tuzzz c форума china-iphone.ru.
Ask question in Russian. I tuzzz from the forum china-iphone.ru.
Вообщем поставил Froyo (v5)
после прошивки при первом запуске появляется калибровка экрана, но на нажатия никак не реагирует
поставил назад 3245, на ней все нормально
Возможно ли это из-за загрузчика uboot, как можно посмотреть его версию и возможно ли обновить его с SD, т.к. возможности с ПК нету?
google translate:
In general set Froyo (v5)
after flashing at the first startup, a calibration screen, but clicking does not react
put back 3245, her everything is ok
Is this possible because of the boot uboot, as you can see its version and whether it is possible to update it with SD, because capabilities with a PC no?
Answer on russian forum.
Also read from here and below.
_barsuk_ said:
In my case loader version number is missing. But u0 is 0.6.1.2_1.4.587_OV2655 and u-boot from 2852. And all work fine.
Probably condition is flashing firmware 2852 in the tablet instead of only u0?
IMHO.
Because the firmware is full image and contained u-boot and u0. Flashing u0 need only if camera don't work with 2852 from full image. Of course, if the tablet has not been purchased already with firmware 2852 and above. Without this step you will get many reports of "fre-e-e-ezing" or "stop in android on screen" like in the previous thread.
Click to expand...
Click to collapse
That could be true indeed! I thought those who fixed their problem only flashed U0, but maybe all of them actually tried to flash all of v2852 with the IUW tool. Upshot here is that it should be possible to flash the entire firmware using a bootable SD-card, e.g. not requiring an USB cable.
Can anyone confirm that creating the bootable SD-card for FW2852 using IUW as described in the first post fixed their install of the froyo setup?
If you create a bootable SD-card, Click 'boot disk' on the left instead. Select sd-card to flash on the right
Select the IUS file form the v2852 firmware under 'Choose a wrapped image'
Click to expand...
Click to collapse
After Burn a card sd the empty
This way does not work
Used Win7 x64 and virtual WinXP x86
Excellent Work
Many thanks stragulus!!!!!!!
Now I once again have a usable Pad - the Calibration works perfecly!!!
My route to Froyo was from 3245 to v4. I HAD to flash U-Boot-Nand FIRST. This gave me the Infotm code in the bottom R.H.corner. The only problem was with the calibration.
Again MANY THANKS. Please continue to develop for the Pad.
jp08 said:
After Burn a card sd the empty
This way does not work
Used Win7 x64 and virtual WinXP x86
Click to expand...
Click to collapse
Hmm. I do now recall that someone tried all those methods before to no avail. When I flashed this firmware, I think I did:
* Flash all of FW2852 (over USB)
* Found out that it didn't work 100% as it still booted an older ramdisk
* So after that, flashed U0 with u-boot-nand.bin. That triggered the 2-minute tablet going crazy on first boot.
* Then flashed all of FW2852 again, and now it worked.
Soo.. I think bottomline is, if you haven't seen the tablet go crazy for 2 minutes, it probably didn't work. Question is, is just flashing U0 once with u-boot-nand.bin enough..? It appears this does not work for everyone!?
stragulus said:
Cheers! I welcome custom mods of the base rom. I'm willing to add them as alternatives to the first post by linking to the introductory posts. In this case, it looks like parts of it are suitable for integrating into the base froyo rom (e.g. calendar & contact sync fix). What exactly did you do to fix those?
Click to expand...
Click to collapse
Hi!
I replaced GoogleContactsSyncAdapter.apk and GoogleCalendarSyncadapter.apk with the ones from my phone. I am 98% sure I replaced only these two, because I didn't note down the names.
Now I'm trying to solve the next problem I have in the list: I can't leave the pad in standby, as it drains the battery like it was awake.
Yesterday I had a look at proc/wakelocks file to see which processes are requesting wakelocks.
Comparing this file to others around the net and the one of my phone, I found out that some processes were active during standby (they had 0 value in sleep_time row).
Now I haven't here my flytouch, so I can't be precise (I'll edit this lines next days), but I remember that some processes and powermanager were never sleeping (in all other wakelocks files, powemanager was sleeping on standby but main process not, so I think powermanager is faulty and main process not.).
Powermanager is a class contained in system/framework/services.jar so I tried replacing this file with my phone's one. It worked as the wakelocks file was showing that powermanager began to sleep on standby, but I had no improvement in battery life on standby, as, I'm quite sure, the other processes prevent the full sleep of the device.
To you and everyone who reads this: can you give me a help?
Can you fully recharge the flytouch, then disconnect the power supply, note down the start time, live it in sleep mode and then measure how long it takes to get discharged?
It tried myself today: unplugged at 16.30, left it in standby, died at around 19:20 ---> 2h50m of battery power on standby.
(If you also can tell me how long it stays on when you use it, and what kind of use you made, I would really appreciate too! )
Hail to Stragulus.. unlocking the beast!!!!
stragulus,
as usual.. I am riding on someone else's brilliance.. thanks for the update..
Will load it up tonight when get home from work..
My only wish is app2sd...
it has made such an improvement to my Evo with ability to load programs in..
So if someone wants to come up with a fix.. I am sure you will make many internally grateful!!!!
Edit after flashing:
Flashed the clean version WITHOUT verandi addons..
the Calibration works perfectly
feels fast and clean..
had problems with launcher pro .. and Titanium backup..
for some reason using Launcher pro it would not allow Titanium to see the sdcard.. thus couldnt restore my backups..
Played round for a while.. upgraded to Titanium 3.6.1.1 same thing..
went in and wiped Dalvik cache.. still no go..
have shut down launcher pro and installed ADWlauncher (almost the same as launcher pro)
walla.. now Titanium is seeing the SDcards and backup.. confirmed that it restored backed programs and data..
Market is working for me.. just wondering if we can port market from Myn’s Warm TwoPointTwo - RLS 5 into this rom..
as this may be the workaround that will get past the only free apps showing.. I am using it on my Evo and in China..
so usually only get to see free apps.. but with MWTPT I am getting all apps.. I do understand there is a app floating round that is suppose to be able to reset Market in to thinking it is in a zone that will allow it to show all apps.. may need it to load in to this Rom..
Will put it through its paces and report back over the coming week..
verandi said:
It tried myself today: unplugged at 16.30, left it in standby, died at around 19:20 ---> 2h50m of battery power on standby.
(If you also can tell me how long it stays on when you use it, and what kind of use you made, I would really appreciate too! )
Click to expand...
Click to collapse
Hmmm. This time is extremely low for standby mode. I use kernel from 3245. With this kernel battery indicator won't work properly but OS works more stable.
Also I removed Phone.apk and TelephonyProvider.apk. I don't need 3g modem. And 3g modem still does not work with this firmware.
With full charged battery I disconnected charger from tablet at 22:00 (in my local time). Now is 5:25 in my local time and tablet has ~4% battery indicator. From my experience tablet shut down after 5-10 minutes. All this time tablet is in standby.
Verandi
Excellent work and thank you for the Google sync fix - it makes my wowpad WOW!!!
Can you please add these files to the V5 version? Without them there's no sync. If I add your V4 files to the V5 rom there's no calibration. I wonder what else is lost !!!
Thanks,
B
stragulus said:
Cheers! I welcome custom mods of the base rom. I'm willing to add them as alternatives to the first post by linking to the introductory posts. In this case, it looks like parts of it are suitable for integrating into the base froyo rom (e.g. calendar & contact sync fix). What exactly did you do to fix those?
Click to expand...
Click to collapse
Great job. Thank you about that. I've a little question.
I've updated my Flytouch with you sdcard V5. Everything works fine, but i can't get the connection with USB 3G dongle. How i can do ?
There's a program to get the connections ?
I've tried with "quick setting" but nothing happens.
I'm looking forward to hearing from you about that.
Best regards
Please note that you are doing all this at your own risk and i am not responsible for any damage caused during the
process. Dont do it if you dont know what you are doing.
Hi Guys as this is my first post on XDA about rooting and stuff so please dont be harsh. I am not a developer. i am just sharing all this here from different sources which i found out by doing a lot of search and wasting a lot of my precious time
So i thought i will open a separate thread for this phone as i could not see a single post on this phone. Ok i have found out how to Root this phone, installing CWM and also i have found a custom ROM so i thought i will post it here so that it can help others.
Phone Model Number : Star N9880
Varients : Upai N9880, Viewsonic 9880
Specs
- 6 inch capacitive touchscreen
- Android 4.0.3 OS, support Google Play
- Support WiFi, GPS, TV, dual SIM card slot
- Support 3G network: GSM 850/900/1800/1900 & WCDMA 850/2100 MHz
- 5MP back camera + 0.3MP front camera
- Support dual SIM cards at same time,
- Multi-language: English, French, Spanish, Portuguese, German, Italian, Russian...
Phone Style: Bar, multi-touch screen, 6 inch Capacitive touchscreen
Operating System: Android 4.0.3 OS
Processor: MTK MT6575, 1GHz, ARM Cortex A9
Display
Screen Size: 6" touchscreen
Display reulotion: WVGA screen, 800*480 pixel
Color Support: 265K colors
Screen Technology: Multi-touch screen
Camera
Camera Resulotion: 5MP back camera + 0.3MP front camera, digital zoom
Memory
Built-in Memory: 2GB ROM / 512MB RAM,
Memory Card: Support microSD/microSDHC memory card, up to 32GB, support App2SD
Size
Dimensions:144 * 84 * 13mm
Weight: 205g
What in package
1 * N9880 Android Phone
1 * Travel Charger
1 * USB Data Cable
1 * Headphone
1 * Manual
2 * Battery and a Flip case.
Rooting the phone :
http://www.4shared.com/rar/5tilx4YQ/40root.html
1.Please download root file from the link above.
2.Go to settings-developer options-click USB debugging.
3.Connect the phone with computer,turn on usb device.
4.Click the file you download from the link TPSparkyRoot.bat
5.Your phone will restart first time,after the phone start finish(until you see the unlock),click enter in the window of TPSparkyRoot.bat.
6.The phone will restart second time,still the same as first time we did.Then start third time,same as we did in last two times.Click enter then phone was rooted.
7.You will see two more app was installed in your phone that means root phone successfully.
Installing CWM recovery :
Check out this post to learn how to use the SPflash tool http://bm-smartphone-reviews.blogspot.it/2012/05/mt6575-flashing-tutorial.html#comment-form
1) After rooting the phone download the SP flash too from here http://www.4shared.com/folder/Q_MYd0k_/MT6516_Tools.html Password : bm-smartphone-reviews.blogspot.com
( Courtesy : http://bm-smartphone-reviews.blogspot.it/2012/05/mt6575-flashing-tutorial.html#comment-form )
2) And download CWM recovery file from here http://www.4shared.com/folder/w9iaxGla/upai-n9880.html and unzip in a folder.
3) switch off the phone and take out the battery. ( Dont put the battery back )
4) Open the Flash tool and click on the scatter-loading button and then load the "MT6575_Android_scatter_emmc" file from the CWM recovery folder.
5) Just click on the download button and let it complete the process. Put the battery back and now hold the volume up button and power button together until the screen switches on and now you must see CWM recover installed.
Installing the Taiwan upai N9880_ICS_V.01
After installing this ROM camera flash is not working. But i dont really know if its an issue with the
ROM or a hardware issue. So please be prepared and dont blame for any damages
1) Now download the ROM from the link below and place in the SD card.
http://www.4shared.com/zip/SY9YRgTr/Taiwan101-UPAI-N9880_ICS_V01.html
2) Boot in to recovery mode ( Power off the phone, hold the volume up and power button until the phone power on and then leave the buttons)
3) Select the Taiwan ICS zip and update and just sit back for the process to complete. Once the it finishes the process reboot the phone and the phone will now reboot with the HTC one boot animation
Now Enjoy the phone
Feel free to ask me any doubts if you have.
wow.
shri080 said:
Please note that you are doing all this at your own risk and i am not responsible for any damage caused during the
process. Dont do it if you dont know what you are doing.
Hi Guys as this is my first post on XDA about rooting and stuff so please dont be harsh. I am not a developer. i am just sharing all this here from different sources which i found out by doing a lot of search and wasting a lot of my precious time
So i thought i will open a separate thread for this phone as i could not see a single post on this phone. Ok i have found out how to Root this phone, installing CWM and also i have found a custom ROM so i thought i will post it here so that it can help others.
Phone Model Number : Star N9880
Varients : Upai N9880, Viewsonic 9880
Specs
- 6 inch capacitive touchscreen
- Android 4.0.3 OS, support Google Play
- Support WiFi, GPS, TV, dual SIM card slot
- Support 3G network: GSM 850/900/1800/1900 & WCDMA 850/2100 MHz
- 5MP back camera + 0.3MP front camera
- Support dual SIM cards at same time,
- Multi-language: English, French, Spanish, Portuguese, German, Italian, Russian...
Phone Style: Bar, multi-touch screen, 6 inch Capacitive touchscreen
Operating System: Android 4.0.3 OS
Processor: MTK MT6575, 1GHz, ARM Cortex A9
Display
Screen Size: 6" touchscreen
Display reulotion: WVGA screen, 800*480 pixel
Color Support: 265K colors
Screen Technology: Multi-touch screen
Camera
Camera Resulotion: 5MP back camera + 0.3MP front camera, digital zoom
Memory
Built-in Memory: 2GB ROM / 512MB RAM,
Memory Card: Support microSD/microSDHC memory card, up to 32GB, support App2SD
Size
Dimensions:144 * 84 * 13mm
Weight: 205g
What in package
1 * N9880 Android Phone
1 * Travel Charger
1 * USB Data Cable
1 * Headphone
1 * Manual
2 * Battery and a Flip case.
Rooting the phone :
http://www.4shared.com/rar/5tilx4YQ/40root.html
1.Please download root file from the link above.
2.Go to settings-developer options-click USB debugging.
3.Connect the phone with computer,turn on usb device.
4.Click the file you download from the link TPSparkyRoot.bat
5.Your phone will restart first time,after the phone start finish(until you see the unlock),click enter in the window of TPSparkyRoot.bat.
6.The phone will restart second time,still the same as first time we did.Then start third time,same as we did in last two times.Click enter then phone was rooted.
7.You will see two more app was installed in your phone that means root phone successfully.
Installing CWM recovery :
Check out this post to learn how to use the SPflash tool http://bm-smartphone-reviews.blogspot.it/2012/05/mt6575-flashing-tutorial.html#comment-form
1) After rooting the phone download the SP flash too from here http://www.4shared.com/folder/Q_MYd0k_/MT6516_Tools.html Password : bm-smartphone-reviews.blogspot.com
( Courtesy : http://bm-smartphone-reviews.blogspot.it/2012/05/mt6575-flashing-tutorial.html#comment-form )
2) And download CWM recovery file from here http://www.4shared.com/folder/w9iaxGla/upai-n9880.html and unzip in a folder.
3) switch off the phone and take out the battery. ( Dont put the battery back )
4) Open the Flash tool and click on the scatter-loading button and then load the "MT6575_Android_scatter_emmc" file from the CWM recovery folder.
5) Just click on the download button and let it complete the process. Put the battery back and now hold the volume up button and power button together until the screen switches on and now you must see CWM recover installed.
Installing the Taiwan upai N9880_ICS_V.01
After installing this ROM camera flash is not working. But i dont really know if its an issue with the
ROM or a hardware issue. So please be prepared and dont blame for any damages
1) Now download the ROM from the link below and place in the SD card.
http://www.4shared.com/zip/SY9YRgTr/Taiwan101-UPAI-N9880_ICS_V01.html
2) Boot in to recovery mode ( Power off the phone, hold the volume up and power button until the phone power on and then leave the buttons)
3) Select the Taiwan ICS zip and update and just sit back for the process to complete. Once the it finishes the process reboot the phone and the phone will now reboot with the HTC one boot animation
Now Enjoy the phone
Feel free to ask me any doubts if you hav
my nmottum e is tim i want to buy this phone ,but i need to know if the little symbols at the bottom of the phone lite up when you touch them. and as you already know some of those china phones dont have good signal strength, does this one? thank you for the post of all the goodies for this phone. i have looked thought alot of sites trying to find rooting guides, flash tools and only found the root zip. SO THANK YOU SUPER SMART DUDE THAT IS SUPER COOL!!!!!!!
Click to expand...
Click to collapse
Haha thanks dude Yes even i had the same exact doubt before i bought it. It lights up when u touch it and its very nice and the signal strength is also pretty good. but the call quality is ok though. The only thing i dint like in this phone is the viewing angle which is bad. But other than that this is a very good phone. especially the build quality is lovely and also the flip case you get with it is very nice.if you like big screen u can try this out. You can check out my Unboxing video here http://www.youtube.com/watch?v=fgQkmNDlp9U all the best
hey
shri080 said:
Haha thanks dude Yes even i had the same exact doubt before i bought it. It lights up when u touch it and its very nice and the signal strength is also pretty good. but the call quality is ok though. The only thing i dint like in this phone is the viewing angle which is bad. But other than that this is a very good phone. especially the build quality is lovely and also the flip case you get with it is very nice.if you like big screen u can try this out. You can check out my Unboxing video here http://www.youtube.com/watch?v=fgQkmNDlp9U all the best
Click to expand...
Click to collapse
there is the other guy that said the same thing that it had bad viewing angle. but i dont understand? do you mean looking from the side, it does nt look good or what!!!! i think i found someone who has the mtk6577 1gb ram version. i ordered it last night. it was only 215$ shipped ems. so we will see. i wonder if it is what this guy says it is, if the rooting steps the same.
Hey check this one out i think im going to try and get both. Its called a C3 note2!!!!
Sent from my SAMSUNG-SGH-I997 using xda app-developers app
bobo31 said:
there is the other guy that said the same thing that it had bad viewing angle. but i dont understand? do you mean looking from the side, it does nt look good or what!!!! i think i found someone who has the mtk6577 1gb ram version. i ordered it last night. it was only 215$ shipped ems. so we will see. i wonder if it is what this guy says it is, if the rooting steps the same.
Click to expand...
Click to collapse
as my knowledge goes you can not do the same procedure to root MTK6577. Bad viewing angle meaning the image or the video almost blacks out from a side angle which can be sometimes really annoying. And btw did u receive your phone?
After a few week I use n9880 with dual core CPU 6577 version..
I found some problem here..
-.The screen solution not so good,I can see a horizontal line on screen,I don't know it a ROM problem or a screen problem.Maybe If I can try new rom it'll fix the problem or not?!?
-.It not good to watch your screen from the top side.It'll look more dark.
-.Battery gone fast.
-.I try to jack the iphone earphone to n9880 6577 hole to listen the music on iphone earphone.But the speaker alway speakout the same time with the earphone.That speaker should be mute,But it's not! I didn't try the earphone from n9880 yet.So not sure will it have the same problem or not?!
-.Spec showed 2.5Gb of rom space(actually 4Gb) but when I install more app,It's was full at 500Mb only?!? I don't know why?? And I think that should be fix by root and find new rom.
-. I don't know what is the best rom for now,The camera and flash not work or some rom.So any news please update here.
Hey!!!
ther is a sight i have been going to it is called mobileuncle.com. translate the page and type in search on site,n9880mtk6575 or mtk6577 or n9970 or n9977. these are all the same phone pretty much. this site shows how to do what ever u want to do with your phone. it does have a rom or something that you can brush the 2.5gb rom and take away the lines. go look and see. thanks
---------- Post added at 01:01 PM ---------- Previous post was at 12:59 PM ----------
vidsava said:
After a few week I use n9880 with dual core CPU 6577 version..
I found some problem here..
-.The screen solution not so good,I can see a horizontal line on screen,I don't know it a ROM problem or a screen problem.Maybe If I can try new rom it'll fix the problem or not?!?
-.It not good to watch your screen from the top side.It'll look more dark.
-.Battery gone fast.
-.I try to jack the iphone earphone to n9880 6577 hole to listen the music on iphone earphone.But the speaker alway speakout the same time with the earphone.That speaker should be mute,But it's not! I didn't try the earphone from n9880 yet.So not sure will it have the same problem or not?!
-.Spec showed 2.5Gb of rom space(actually 4Gb) but when I install more app,It's was full at 500Mb only?!? I don't know why?? And I think that should be fix by root and find new rom.
-. I don't know what is the best rom for now,The camera and flash not work or some rom.So any news please update here.
Click to expand...
Click to collapse
Pull your batt. and see what the model number say. it just might be the n9970 vresion of this phone!
There seems to be a very similar 6" Android phone out there under various brand names and usually called the i9977, with some versions -- but not all -- claiming a Super AMOLED screen. If it indeed uses a Super AMOLED screen, the side views shouldn't be bad.
I can't post links, but search YouTube for "i9977 mt6577 English" and you'll find a video showing the screen on this phone.
There's also the N9776 which claims, again in some versions, to have an AMOLED screen.
Hey!!!
i think im going to get this!!! C3
bobo31 said:
ther is a sight i have been going to it is called mobileuncle.com. translate the page and type in search on site,n9880mtk6575 or mtk6577 or n9970 or n9977. these are all the same phone pretty much. this site shows how to do what ever u want to do with your phone. it does have a rom or something that you can brush the 2.5gb rom and take away the lines. go look and see. thanks
---------- Post added at 01:01 PM ---------- Previous post was at 12:59 PM ----------
Pull your batt. and see what the model number say. it just might be the n9970 vresion of this phone!
Click to expand...
Click to collapse
Thank you, my phone is n9970,And I was try to find the info in mobileuncle already. they are all chinese language,And google translate not make me understand it correct?! I not sure which one is the last Rom that work very well,and I don't know how to make image recovery file before I root the phone. I want to back up it all as image file. Please tell me where can I find step by step for root , make image file and setup new rom for n9970 in english version.please help..
Thank you
Hey!!!
vidsava said:
Thank you, my phone is n9970,And I was try to find the info in mobileuncle already. they are all chinese language,And google translate not make me understand it correct?! I not sure which one is the last Rom that work very well,and I don't know how to make image recovery file before I root the phone. I want to back up it all as image file. Please tell me where can I find step by step for root , make image file and setup new rom for n9970 in english version.please help..
Thank you
Click to expand...
Click to collapse
I saw this today i think it will help! go here: http://hi.baidu.com/esocu/item/c1279ad94eda283be2108f5e
HEY!!!!!
Check this out!!!! http://products.mobileuncle.com/forum.php?mod=viewthread&tid=199890&highlight=n9880 it is for the n9880 mtk6577 which is the N9970:good:
Hey!!!
vidsava said:
Thank you, my phone is n9970,And I was try to find the info in mobileuncle already. they are all chinese language,And google translate not make me understand it correct?! I not sure which one is the last Rom that work very well,and I don't know how to make image recovery file before I root the phone. I want to back up it all as image file. Please tell me where can I find step by step for root , make image file and setup new rom for n9970 in english version.please help..
Thank you
Click to expand...
Click to collapse
I found this phone and i really would like to get it, do you like it? And when you get calls can you hear the other people loud and clear? How long does batt last? I think I AM NOT FOR SURE BUT, I dont see why you cant use the android kitchen to make your own rom. it seems kinnda easy to do.
bobo31 said:
I found this phone and i really would like to get it, do you like it? And when you get calls can you hear the other people loud and clear? How long does batt last? I think I AM NOT FOR SURE BUT, I dont see why you cant use the android kitchen to make your own rom. it seems kinnda easy to do.
Click to expand...
Click to collapse
It's have a few problem to me.But I still love it.
- Horizontal line alway show full screen.
- rubber at border of the flip cover was easy damaged.And it's not look good now.
- when I call the speaker is not so loud,I think my HTC HD2 are louder,But voice so clear.
- Wifi are weaker than HTC HD2,I use at the same time hd2 show 2line signal,but n9970 less than that.
- after charge batter full,I use wifi and watch youtube and use speaker ,It's can work about 3-4 hours,That ok for me
- Rom can work only 502Mb,Need to use 2.5gb as spec said.But I don't know what is the best rom now?
- lastest Rom on china webboard still have a problem on flash and camera.So I wait for better rom.
- watch screen from above side are so bad dark.
I don't know about android kitchen and how to make my own rom, So If you get n9970 please make the best Rom for me too.
I have very less time to learn it.
Thank you very much.
Hi
vidsava said:
It's have a few problem to me.But I still love it.
- Horizontal line alway show full screen.
- rubber at border of the flip cover was easy damaged.And it's not look good now.
- when I call the speaker is not so loud,I think my HTC HD2 are louder,But voice so clear.
- Wifi are weaker than HTC HD2,I use at the same time hd2 show 2line signal,but n9970 less than that.
- after charge batter full,I use wifi and watch youtube and use speaker ,It's can work about 3-4 hours,That ok for me
- Rom can work only 502Mb,Need to use 2.5gb as spec said.But I don't know what is the best rom now?
- lastest Rom on china webboard still have a problem on flash and camera.So I wait for better rom.
- watch screen from above side are so bad dark.
I don't know about android kitchen and how to make my own rom, So If you get n9970 please make the best Rom for me too.
I have very less time to learn it.
Thank you very much.
Click to expand...
Click to collapse
I ordered the n9970 mtk6577 phone today. I hope to have it soon.
Check this out!!!!!
bobo31 said:
I ordered the n9970 mtk6577 phone today. I hope to have it soon.
Click to expand...
Click to collapse
This is what i found about the N9970 I hope some one here can make better since of it!
European musical styles N9770
mtk6577 the
ANDROID version 4.09
version number: e1809_v77_gq1008_5647_20120810
the first time at the uncle tutorial posts, share their own experiences!
Let us talk about before I have a 6575 version of n8000, due to the brush wrong the rom completely brick then bought n9770 , due to the relationship between n8000 Brush has changed careful, I remind brush body of the faithful, when you see someone sharing Brush Pack , if not too much description, or say what shared version, please be especially careful, because the brush of a the aggregate n8000 the rom, later found that rom can not find the driver file, it is estimated that because so dead, so before you brush is best to find their own mobile phone version of the original rom before considering the the root machine or brush package.
I n9770 0810 version rom in N9770- 20120810_e1809c_v77_gq1008_5647.zip, can be found within the forum, by the test brush to restore completely the same with me before, so if the 0810 version of the Friends of the Brush, due to brush the root package , the phone found a problem, then restore the factory version of this package can be heavy brush heavy new root machine. As far as I know, n9770 before some versions, rom package the final figure is not 5647, but 9p017, 9p017 version rom is basically the same with me before 6575 n8000 rom package after digital, that is to say, n9770 version of the phone if it is a the 9p017 version of the basic hardware of the phone is the choice of N8000 hardware, such as after the camera and capacitive screen driver related to the 5647 version of different, if found phone camera malfunction, or splash screen, the resolution is very low perhaps chose the wrong drive moving or wrong brush the package by the 0810 version of the mobile phones brush rom version before the former version does not have the latest driver.
Following share my Brush steps, I will separate the several parts to illustrate that contains the driver installation, heavy brush factory, wire brush the root machine, Uncle tools to recover part of the IMEI, etc.. . . . .
Prepare the following documents, all files are to come back from the forum
First: drive installation method
the first step: first solve the driver problem,
I Window7 phone open, the system will find the new hardware on the 6577 USB driver installed, installed after the following figure,
This is when, if you have to install the the good bowl pods phone platform to see if I can connect the phone, no problem, after the completion of the first step. If not successful, try also can download other drivers to try again (6575's drive), this drive is mainly used to identify in the computer system , used in such third-party phone platform.
Step two: is more important, wire brush must do this step,
open the [Device Manager] computer, then phone off, remove the battery, connect the data cable, the system will issue a "must" sound, sound may not stop repeat, may stop connection break, after a look at the Device Manager port is open and the installed driver, if it is an exclamation point, right point update 6577 USB driver installed following figure.
This drive is mainly to identify hardware connection port, the software need to find the wire brush the port to brush package.
If you try to look online before the installation of the driver can not use, compatible with 6575 can also manually update, click "install from disk" methods such as the following diagram.
Second step install the driver failed to download the following driver installation, this drive xp, vista, the
VCOM driver 6575and6577.rar win7 USB
manntim31, If you want to see this post hidden content, please Reply
. . . . . . . . . . . . . . . . . . . . . . . .
Part II: The wire brush original ROM method
method is basically the two kinds
first one is able to open the phone, the splash screen, or other hardware failure and other spirits in heavy brush recovery.
The second is not open the phone to save the machine.
The first original Brush normal recovery methods:
1. Computer port driver installed first
. Phone off Remove the battery
3. Original line brush ROM package
4. SP_mdk software
SmartPhone Multi-port Download Tool brush back to the factory settings, the benefits of this software allows you to select the drive automatically.
Steps: the computer after the driver has been installed, so that you can brush machine, remove the first cell phone battery, to open sp_mdt software Brush with 9770-20120810_e1809c_v77_gq1008_5647 original package
. Press the Scatter File],
2. Select the original package boot file MT6577_Android_scatter_emmc.txt
3. [Select screen and camera,
4. Press [Unlock], select the drive (see below)
I have the 0810 version of the driver, rear lens: ov5647 front lens: hi704_yuv screen drive: RX_50NT_415B
5. SelAll tick
6. Figure for the right
7. (Check again)
8. Do not connect your phone, press Start all
9. (You can see the start countdown)
10. Phone off remove the battery to access the data line, after the software to find the port brush package, wait for brush package completed
Congratulations! ! . Picture below represents brush package completed, Stop all, remove the data lines, re-open the phone to see!
(Take a look around the money head is normal, there is no splash screen, the Friends of the 0810 version of the machine in general, it should be no problem, as the problem , on behalf of your phone may be an earlier version of the hardware, try to re-brush package, choose other drive, or not, may 9p017 number of tail version, it is possible the driver: mt9p017_raw [This is a hardware-based n8000], the 0810 version of the package is not there, you can download other versions of rom package to brush look at, think about yourself when to buy)
PS: last mention a successful brush package, open play original rom folder, you see the found
uboot_e1809c_v77_gq1008_5647.bin the file has been modified,
This is based on you select the other drive as the boot file to save, if you again to brush this packet to use another SP_flash_tool software, you will find not selected drive situation state there is no splash screen, can explain why a lot of friends with appears after the splash screen is like SP_flash_tool software brush machine.
The second is not open the phone to save machine
usually this situation is chaotic brush rom, or the driver is not installed, such as a break caused mostly. To brush back conditions is also found that the hardware of the computer connected to dismantle electric phone, or is no reaction, the gods can not put out.
1. Computer port driver installed first
. Phone off Remove the battery
3. Original line brush ROM package
4. Use mobile the uncle SP_Flash_Tool_v3.1222.00 software
steps:
1. The First Open mobile uncle SP_Flash_Tool_v3.1222.00,
. Select the Scatter-Loading
3. Select the boot file
4. All of the following documents full tick
5. To prepare phone removed the battery, first not access the data line, press the Download
6. Below to start searching, then access the data line
7. The software automatically Brush bag, waiting to complete
8. Green circle is completed there will be representatives completed! Open the phone and see! !
SmartPhone Multi-port Download Tool fact, this approach should also be able to use the first method to deal with, just download the version format / download can be used, like this software uncle solve, if after brushing phone has been able to open but appear splash screen or lens malfunction, then the first method to select the drive to paint again. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Part III wire brush root method first talk n9770 root machine before, a key the root tool completely different root tools are the root file is sent to the phone directory specified, so no hard drive
and any file, replace. But now due to technical problems, the only line brush resolved, therefore must place the crack boot.img (contains the root file) straight brush into the phone, while the root file boot.img, it seems that, The 0710 version, after joining the root file repackaged, as far as I know, n9770, from 0705 to 0713, the rom package version number of the tail are 9p017, 0725 and the end of 0810 the number is 5647, has said 9p017 version is based on n8000 hardware for the upgrade, so the hardware is old driver, 9p017 version of the package is not as if 5647 the new version of the driver, and the 5647 version of the package without 9p017 old driver, a lot of people, chaos is chaos here, so 0725 and later versions of root brush replaced the earlier version of the brush into the cause splash screen, camera failure, the most simple way is to root and then their own original boot.img version from the new brush into time substitutes a while to not remove the root file, so normal, the truth is safe. As long as the know is of 9p017 still 5647 version, so you should know to download that rom use that drive to brush package, the problem will be reduced. ps: the principle problem, so when you use the wire brush root , restore the original file and driver version is more important, please find their own versions, such as uncertainty, think about when to buy and download the same period original package, make sure can find the you need, no splash screen, such as the failure problem root forum have all versions of the package, the can down try, otherwise such a key root tool only root machine it! Even if not the root problem , just brush original package to restore and driving problem has led to a lot of people headaches headache is because you have the wrong version of the original package, due to driver problems, as long as you drive your original package should be no problem, do not see the new version of chaos brush.
Know the version
20120705_e1809c_v77_gq1008_ 9p017
20,120,713 e1809c-v77-gq1008- 9p017
20120725_e1809c_v77_gq1008_ 5647
20120810_e1809c_v77_gq1008_ 5647
9p017 version available with the following drivers
The 5647 version of the following drive
Following the 0810 version of the brush method
PS: I brush root before SmartPhone Multi-port Download Tool, election 0810 version of the driver, restore factory version, when the IMEI is normal PS: Note, in each brush when the package is completed, the software has been completed, do not rush to remove the data cable, before the removal of the first to hear the USB disconnection sound after, and then stop the software, turn off the software only remove the USB, which is a good habit!
1. Ready to the Oral wind N9770 boot file
2. Open mobile uncle SP_Flash_Tool_v3.1222.00 is
3. Phone off Remove the battery is the first step decompression the Oral wind N9770 boot.rar There is a boot.img (creation date 2012-07-10, means BOOT crack under the 0710 or previous version), if not The boot file uboot_e1809c_v77_gq1008_5647.txt direct COPY of the original on the Oral wind N9770 boot folder inside. The second step mobile uncle SP_Flash_Tool_v3.1222.00 opens Scatter Loading, select Oral wind N9770 boot folder inside the boot file
Opens, you will see a boot.img tick, and then press Download
At this time, if the aphorisms prompted, press ok it
Saw searching, it will tear down the cell phone battery to insert the data cable, brush package began
Wait for the the DOWLOAD OK green circle out on completion of the
Replace the battery after open the phone to run it once (must first boot time), the
splash screen now. . . . Let it
then take a look there the superuser and uncle Tools, after brushing should have been there, turn off the phone, removed the battery! Continue with the next
step
mobile uncle SP_Flash_Tool_v3.1222.00 for the painted original BOOT.img
above, Scatter Loading, open the original ROM file folder, and select the boot files,
after only tick the boot.IMG other cancellation Figure
After Dowload, after waiting for seaching appear, insert the data line (phone off demolition electrical state), automatic brush boot until the green circle appeared complete. Re-open the phone to see if all normal, no splash screen, front and rear lens normally has installed superuser and mobile uncle Toolbox, phone, open the Toolbox, look to have root! IMEI is all normal, this is the first root.
After this, I try to brush the original package once, in the second accident, I do not know the reason for the port are disconnected, things did not brush into the dead! ! Can not phone, the heavy brush does not work, is the brush does not go in, but fortunately, the computer can also find equipment last. . . . . . . . Hee hee hee! Course to life, but the phone re-opened imei will invalid, relevant, how to deal with the back say.
Part IV uncle tools restore IMEI first description with Uncle tools to restore the IMEI, I have a backup the IMEI to recover If you do not have a backup file, many online teaching methods to restore the IMEI, the premise has ROOT. I only own briefing. PS: I ROOT for the first time after the success of IMEI did not fall on the first time backed up with Uncle tools, I lost IMEI is in the second condition only IMEI valid, invalid does not mean or call .
My approach is to first update uncle Tools Forum has released version of the the "mobile uncle Toolbox V2.2.0-0813" to support the 6577 phone, pictures
Recovery must have ROOT
enter the IMEI backup and recovery (MTK) you will see the file in the backup file md5 SD card with the above machine md5 is different, select the last restore the IMEI sd2 card, select Restart
To finalize
The fifth one this special treatment practices
sometimes appear, are usually driven not installed package brush out of the question, brush the wrong package, Brush usb break, are likely to cause the phone can not open this heavy brush when you then what software or update usb drive non-stop, in the end will find what brush does not go in, is the brush for a while, in the second situation, the port is stopped, then I sure the phone system, so the phone is turned on can not be able to find the port, usb connection, but re-brush is the brush does not go in there a port error problem, when I Another approach is to use the "mobile uncle SP_Flash_Tool_v3 .1222.00 ", the first re-Format phone, then you can use the top of the first and second method used DOWNLOAD reinstall the system, but after IMEI invalid and somehow save the phone in the state of radio , the computer can be found in hardware, mobile phones are not bricks and mortar, the Format is the ultimate method. This method when I n8000 has repeatedly trial, the most important thing is to brush some unknown rom or different mobile phone models package. The final solution, the best Freeze brush did not grasp the package, risk, or some non-essential not to use this method. Out of the situation, as shown in
The ultimate format **
This action will be completed after direct use Dowload,
like a brush to re-package in accordance with Method 2, so alive. PS: If you connect the phone did not find the hardware, I approach, repair it, I N8000 is dead brick waiting to be serviced. Mention one, n9770 though it is a phone model, but is in fact a mobile phone, n9770-9p017 n9770-5647, the use of such understanding on the best 9p017 latest version should be 2012-07-13 right 5647 latest should be 2012-08-10. Maybe there is a method you can let 9p017-0713 version into 9p017-0810 version, the 0810 version is to heavy brush, very possible will splash screen, after re-root machine, again after the SmartPhone the Multi-port Download Tool software single brush 0713 version rom within 3 files, first create a new folder to copy the past, the first one is the boot file: MT6577_Android_scatter_emmc.TXT second is the the boot.img third is uboot_e1809c_v77_gq1008_9p017.BIN (This file is not a driver can not choose) Although such can select the the 9p017 drive but actually what will happen I do not know, to see if there is no one to try it, but if as a brick . . . . . . . Please do not come to me in trouble! ! ! ! Honest, personal feel no need to feel not much different, and does not replace the 0810 version is the same as not able to play the game, not because of the update of the 0810, the phone will fly, so to think of it! Hardware anyway, can not replace. . . . Above content can help a friend to learn more about the situation, select the desired means wish brush package successfully! ! ! Winners please share Replies to talk about my own cell phone, with what version of the package, choose what drive, so multi-benefit of latecomers! Thank you, thank! !
Reviews
Rui Qi is not simple to the very time a teaching text ~ Moderator Big Brother and quick Medal! ~ Posted at 2012-9-10 02:09
◆ ◆
Here is a quick reply, and quickly try Oh
I know
post_newreply
3 people have rated Flights Less reason
cjsoong + 10 Is a force!
knight1082 + 10 Is a force!
Rui Qi + 10 Too detailed to estimated 2-3 hours to the birth of this article to
Total score: Flights + 30 View all ratings
2012-10-28 20:04 set highlighted this topic by sonpost
Share:
QQ space
Tencent microblogging
Tencent friends
Favorite
top
step one foot 0
ratings
[Welcome to] to 〖mobile uncle - Oral wind N9770 District〗
Reviews Reply Report
---------- Post added at 09:11 PM ---------- Previous post was at 08:41 PM ----------
This is the link! http://products.mobileuncle.com/thread-199693-1-1.html:laugh:
STOP!!!!!! read!!!!!
bobo31 said:
This is what i found about the N9970 I hope some one here can make better since of it!
European musical styles N9770
mtk6577 the
ANDROID version 4.09
version number: e1809_v77_gq1008_5647_20120810
the first time at the uncle tutorial posts, share their own experiences!
Let us talk about before I have a 6575 version of n8000, due to the brush wrong the rom completely brick then bought n9770 , due to the relationship between n8000 Brush has changed careful, I remind brush body of the faithful, when you see someone sharing Brush Pack , if not too much description, or say what shared version, please be especially careful, because the brush of a the aggregate n8000 the rom, later found that rom can not find the driver file, it is estimated that because so dead, so before you brush is best to find their own mobile phone version of the original rom before considering the the root machine or brush package.
I n9770 0810 version rom in N9770- 20120810_e1809c_v77_gq1008_5647.zip, can be found within the forum, by the test brush to restore completely the same with me before, so if the 0810 version of the Friends of the Brush, due to brush the root package , the phone found a problem, then restore the factory version of this package can be heavy brush heavy new root machine. As far as I know, n9770 before some versions, rom package the final figure is not 5647, but 9p017, 9p017 version rom is basically the same with me before 6575 n8000 rom package after digital, that is to say, n9770 version of the phone if it is a the 9p017 version of the basic hardware of the phone is the choice of N8000 hardware, such as after the camera and capacitive screen driver related to the 5647 version of different, if found phone camera malfunction, or splash screen, the resolution is very low perhaps chose the wrong drive moving or wrong brush the package by the 0810 version of the mobile phones brush rom version before the former version does not have the latest driver.
Following share my Brush steps, I will separate the several parts to illustrate that contains the driver installation, heavy brush factory, wire brush the root machine, Uncle tools to recover part of the IMEI, etc.. . . . .
Prepare the following documents, all files are to come back from the forum
First: drive installation method
the first step: first solve the driver problem,
I Window7 phone open, the system will find the new hardware on the 6577 USB driver installed, installed after the following figure,
This is when, if you have to install the the good bowl pods phone platform to see if I can connect the phone, no problem, after the completion of the first step. If not successful, try also can download other drivers to try again (6575's drive), this drive is mainly used to identify in the computer system , used in such third-party phone platform.
Step two: is more important, wire brush must do this step,
open the [Device Manager] computer, then phone off, remove the battery, connect the data cable, the system will issue a "must" sound, sound may not stop repeat, may stop connection break, after a look at the Device Manager port is open and the installed driver, if it is an exclamation point, right point update 6577 USB driver installed following figure.
This drive is mainly to identify hardware connection port, the software need to find the wire brush the port to brush package.
If you try to look online before the installation of the driver can not use, compatible with 6575 can also manually update, click "install from disk" methods such as the following diagram.
Second step install the driver failed to download the following driver installation, this drive xp, vista, the
VCOM driver 6575and6577.rar win7 USB
manntim31, If you want to see this post hidden content, please Reply
. . . . . . . . . . . . . . . . . . . . . . . .
Part II: The wire brush original ROM method
method is basically the two kinds
first one is able to open the phone, the splash screen, or other hardware failure and other spirits in heavy brush recovery.
The second is not open the phone to save the machine.
The first original Brush normal recovery methods:
1. Computer port driver installed first
. Phone off Remove the battery
3. Original line brush ROM package
4. SP_mdk software
SmartPhone Multi-port Download Tool brush back to the factory settings, the benefits of this software allows you to select the drive automatically.
Steps: the computer after the driver has been installed, so that you can brush machine, remove the first cell phone battery, to open sp_mdt software Brush with 9770-20120810_e1809c_v77_gq1008_5647 original package
. Press the Scatter File],
2. Select the original package boot file MT6577_Android_scatter_emmc.txt
3. [Select screen and camera,
4. Press [Unlock], select the drive (see below)
I have the 0810 version of the driver, rear lens: ov5647 front lens: hi704_yuv screen drive: RX_50NT_415B
5. SelAll tick
6. Figure for the right
7. (Check again)
8. Do not connect your phone, press Start all
9. (You can see the start countdown)
10. Phone off remove the battery to access the data line, after the software to find the port brush package, wait for brush package completed
Congratulations! ! . Picture below represents brush package completed, Stop all, remove the data lines, re-open the phone to see!
(Take a look around the money head is normal, there is no splash screen, the Friends of the 0810 version of the machine in general, it should be no problem, as the problem , on behalf of your phone may be an earlier version of the hardware, try to re-brush package, choose other drive, or not, may 9p017 number of tail version, it is possible the driver: mt9p017_raw [This is a hardware-based n8000], the 0810 version of the package is not there, you can download other versions of rom package to brush look at, think about yourself when to buy)
PS: last mention a successful brush package, open play original rom folder, you see the found
uboot_e1809c_v77_gq1008_5647.bin the file has been modified,
This is based on you select the other drive as the boot file to save, if you again to brush this packet to use another SP_flash_tool software, you will find not selected drive situation state there is no splash screen, can explain why a lot of friends with appears after the splash screen is like SP_flash_tool software brush machine.
The second is not open the phone to save machine
usually this situation is chaotic brush rom, or the driver is not installed, such as a break caused mostly. To brush back conditions is also found that the hardware of the computer connected to dismantle electric phone, or is no reaction, the gods can not put out.
1. Computer port driver installed first
. Phone off Remove the battery
3. Original line brush ROM package
4. Use mobile the uncle SP_Flash_Tool_v3.1222.00 software
steps:
1. The First Open mobile uncle SP_Flash_Tool_v3.1222.00,
. Select the Scatter-Loading
3. Select the boot file
4. All of the following documents full tick
5. To prepare phone removed the battery, first not access the data line, press the Download
6. Below to start searching, then access the data line
7. The software automatically Brush bag, waiting to complete
8. Green circle is completed there will be representatives completed! Open the phone and see! !
SmartPhone Multi-port Download Tool fact, this approach should also be able to use the first method to deal with, just download the version format / download can be used, like this software uncle solve, if after brushing phone has been able to open but appear splash screen or lens malfunction, then the first method to select the drive to paint again. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Part III wire brush root method first talk n9770 root machine before, a key the root tool completely different root tools are the root file is sent to the phone directory specified, so no hard drive
and any file, replace. But now due to technical problems, the only line brush resolved, therefore must place the crack boot.img (contains the root file) straight brush into the phone, while the root file boot.img, it seems that, The 0710 version, after joining the root file repackaged, as far as I know, n9770, from 0705 to 0713, the rom package version number of the tail are 9p017, 0725 and the end of 0810 the number is 5647, has said 9p017 version is based on n8000 hardware for the upgrade, so the hardware is old driver, 9p017 version of the package is not as if 5647 the new version of the driver, and the 5647 version of the package without 9p017 old driver, a lot of people, chaos is chaos here, so 0725 and later versions of root brush replaced the earlier version of the brush into the cause splash screen, camera failure, the most simple way is to root and then their own original boot.img version from the new brush into time substitutes a while to not remove the root file, so normal, the truth is safe. As long as the know is of 9p017 still 5647 version, so you should know to download that rom use that drive to brush package, the problem will be reduced. ps: the principle problem, so when you use the wire brush root , restore the original file and driver version is more important, please find their own versions, such as uncertainty, think about when to buy and download the same period original package, make sure can find the you need, no splash screen, such as the failure problem root forum have all versions of the package, the can down try, otherwise such a key root tool only root machine it! Even if not the root problem , just brush original package to restore and driving problem has led to a lot of people headaches headache is because you have the wrong version of the original package, due to driver problems, as long as you drive your original package should be no problem, do not see the new version of chaos brush.
Know the version
20120705_e1809c_v77_gq1008_ 9p017
20,120,713 e1809c-v77-gq1008- 9p017
20120725_e1809c_v77_gq1008_ 5647
20120810_e1809c_v77_gq1008_ 5647
9p017 version available with the following drivers
The 5647 version of the following drive
Following the 0810 version of the brush method
PS: I brush root before SmartPhone Multi-port Download Tool, election 0810 version of the driver, restore factory version, when the IMEI is normal PS: Note, in each brush when the package is completed, the software has been completed, do not rush to remove the data cable, before the removal of the first to hear the USB disconnection sound after, and then stop the software, turn off the software only remove the USB, which is a good habit!
1. Ready to the Oral wind N9770 boot file
2. Open mobile uncle SP_Flash_Tool_v3.1222.00 is
3. Phone off Remove the battery is the first step decompression the Oral wind N9770 boot.rar There is a boot.img (creation date 2012-07-10, means BOOT crack under the 0710 or previous version), if not The boot file uboot_e1809c_v77_gq1008_5647.txt direct COPY of the original on the Oral wind N9770 boot folder inside. The second step mobile uncle SP_Flash_Tool_v3.1222.00 opens Scatter Loading, select Oral wind N9770 boot folder inside the boot file
Opens, you will see a boot.img tick, and then press Download
At this time, if the aphorisms prompted, press ok it
Saw searching, it will tear down the cell phone battery to insert the data cable, brush package began
Wait for the the DOWLOAD OK green circle out on completion of the
Replace the battery after open the phone to run it once (must first boot time), the
splash screen now. . . . Let it
then take a look there the superuser and uncle Tools, after brushing should have been there, turn off the phone, removed the battery! Continue with the next
step
mobile uncle SP_Flash_Tool_v3.1222.00 for the painted original BOOT.img
above, Scatter Loading, open the original ROM file folder, and select the boot files,
after only tick the boot.IMG other cancellation Figure
After Dowload, after waiting for seaching appear, insert the data line (phone off demolition electrical state), automatic brush boot until the green circle appeared complete. Re-open the phone to see if all normal, no splash screen, front and rear lens normally has installed superuser and mobile uncle Toolbox, phone, open the Toolbox, look to have root! IMEI is all normal, this is the first root.
After this, I try to brush the original package once, in the second accident, I do not know the reason for the port are disconnected, things did not brush into the dead! ! Can not phone, the heavy brush does not work, is the brush does not go in, but fortunately, the computer can also find equipment last. . . . . . . . Hee hee hee! Course to life, but the phone re-opened imei will invalid, relevant, how to deal with the back say.
Part IV uncle tools restore IMEI first description with Uncle tools to restore the IMEI, I have a backup the IMEI to recover If you do not have a backup file, many online teaching methods to restore the IMEI, the premise has ROOT. I only own briefing. PS: I ROOT for the first time after the success of IMEI did not fall on the first time backed up with Uncle tools, I lost IMEI is in the second condition only IMEI valid, invalid does not mean or call .
My approach is to first update uncle Tools Forum has released version of the the "mobile uncle Toolbox V2.2.0-0813" to support the 6577 phone, pictures
Recovery must have ROOT
enter the IMEI backup and recovery (MTK) you will see the file in the backup file md5 SD card with the above machine md5 is different, select the last restore the IMEI sd2 card, select Restart
To finalize
The fifth one this special treatment practices
sometimes appear, are usually driven not installed package brush out of the question, brush the wrong package, Brush usb break, are likely to cause the phone can not open this heavy brush when you then what software or update usb drive non-stop, in the end will find what brush does not go in, is the brush for a while, in the second situation, the port is stopped, then I sure the phone system, so the phone is turned on can not be able to find the port, usb connection, but re-brush is the brush does not go in there a port error problem, when I Another approach is to use the "mobile uncle SP_Flash_Tool_v3 .1222.00 ", the first re-Format phone, then you can use the top of the first and second method used DOWNLOAD reinstall the system, but after IMEI invalid and somehow save the phone in the state of radio , the computer can be found in hardware, mobile phones are not bricks and mortar, the Format is the ultimate method. This method when I n8000 has repeatedly trial, the most important thing is to brush some unknown rom or different mobile phone models package. The final solution, the best Freeze brush did not grasp the package, risk, or some non-essential not to use this method. Out of the situation, as shown in
The ultimate format **
This action will be completed after direct use Dowload,
like a brush to re-package in accordance with Method 2, so alive. PS: If you connect the phone did not find the hardware, I approach, repair it, I N8000 is dead brick waiting to be serviced. Mention one, n9770 though it is a phone model, but is in fact a mobile phone, n9770-9p017 n9770-5647, the use of such understanding on the best 9p017 latest version should be 2012-07-13 right 5647 latest should be 2012-08-10. Maybe there is a method you can let 9p017-0713 version into 9p017-0810 version, the 0810 version is to heavy brush, very possible will splash screen, after re-root machine, again after the SmartPhone the Multi-port Download Tool software single brush 0713 version rom within 3 files, first create a new folder to copy the past, the first one is the boot file: MT6577_Android_scatter_emmc.TXT second is the the boot.img third is uboot_e1809c_v77_gq1008_9p017.BIN (This file is not a driver can not choose) Although such can select the the 9p017 drive but actually what will happen I do not know, to see if there is no one to try it, but if as a brick . . . . . . . Please do not come to me in trouble! ! ! ! Honest, personal feel no need to feel not much different, and does not replace the 0810 version is the same as not able to play the game, not because of the update of the 0810, the phone will fly, so to think of it! Hardware anyway, can not replace. . . . Above content can help a friend to learn more about the situation, select the desired means wish brush package successfully! ! ! Winners please share Replies to talk about my own cell phone, with what version of the package, choose what drive, so multi-benefit of latecomers! Thank you, thank! !
Reviews
Rui Qi is not simple to the very time a teaching text ~ Moderator Big Brother and quick Medal! ~ Posted at 2012-9-10 02:09
◆ ◆
Here is a quick reply, and quickly try Oh
I know
post_newreply
3 people have rated Flights Less reason
cjsoong + 10 Is a force!
knight1082 + 10 Is a force!
Rui Qi + 10 Too detailed to estimated 2-3 hours to the birth of this article to
Total score: Flights + 30 View all ratings
2012-10-28 20:04 set highlighted this topic by sonpost
Share:
QQ space
Tencent microblogging
Tencent friends
Favorite
top
step one foot 0
ratings
[Welcome to] to 〖mobile uncle - Oral wind N9770 District〗
Reviews Reply Report
---------- Post added at 09:11 PM ---------- Previous post was at 08:41 PM ----------
This is the link! http://products.mobileuncle.com/thread-199693-1-1.html:laugh:
Click to expand...
Click to collapse
I was wrong, this is for the N9770 not the N9970 sorry!!!!! Do not try this for your N9970, WILL BRICK IT FOR SURE!!!!:silly:
OK!!!
Hi this may help someone that has an ime prob with any mtk65xx phone.http://forum.gsmhosting.com/vbb/f723/mtk-6577-cant-repair-imei-1543530/hope this help!
Hey!!!
bobo31 said:
Hi this may help someone that has an ime prob with any mtk65xx phone.http://forum.gsmhosting.com/vbb/f723/mtk-6577-cant-repair-imei-1543530/hope this help!
Click to expand...
Click to collapse
Yall have to get this if you know what you are doing!!! http://code.google.com/p/custom-rom-creator-studio/
Hi, I am creating this thread for anyone who purchases the Ampe A85q Quad Core.
I got mine from FocalPrice Singapore for £70 (inc a £5 discount) just over a week ago and it runs great, at times so I am now looking at improving it, where possible and with the blessing of XDA here, I will post as much info as I can and hopefully do a few things to it, to make it better. I have already found some information out that I will share but having never replaced an existing Rom and such, I am hoping some help is available to guide where necessary.
Today my daughter bought it to me, it had locked up and crashed in an ON state. After a long-hold power, it switched off and switched back on as normal. I then factory reset it and then changed the language and disabled Google PinYin.
Confusingly, the Ampe website (szampe.com) shows the tablet labelled as a A8003QD but another googled site shows it listed as both. Having checked the makers site and specs I see it must be the same tablet. As this tablet is quite new, there are very few results for it.
Official link : http://www.szampe.com/en/Products_show.asp?id=180&i=4
Supporting site showing matching model number : tattoo-ipl.com/productsshow.asp?id=1619
Szampe is now offering a A8003QD Ampe Firmware Update, direct link :
2013/7/24 - http://www.szampe.com/UploadFile/file/2011-08/0335.rar (525MB) #Note I am yet to try this and will add any eventual outcome to this thread.
The download just finished. The rar file contains
FOLDER : A8003QD 爱魅 改乐投风格、4K不支持4个窗口播放的软件20130427 (translated = A8003QD love charm happy to vote to change style, 4K does not support 4 Window Play Software 20130427)
------ and contains >>>> aimei_anpei8003_a31s_v2.0_4.1.1_20130429_[1024x768_ctp兼容_双Camera0308_gsensor兼容_ddr360].img
FOLDER : 全志A31升级工具安装 (translated = Allwinner A31 upgrade tool is installed)
------ and contains >>>> 升级指南（A31主控）.doc (translated = Upgrade Guide (A31 Master))
------ and contains >>>> PhoenixUSBPro_Cn_V330_20121204.rar
------ and contains >>>> PhoenixSuitPacket-V1_0003Beta.rar
------ and contains >>>> PhoenixSuitPacket.msi
Having converted and translated the above .doc file I see some instructions on what to do, however some of the instructions appear to be missing. I need to get this done better so it can be followed properly.
Problems :
Rom language - The tablet came with English setup already. A factory reset changes this back to Chinese.
Keyboard is set to English UK.
Google PinYin can and is now disabled
Some of the features are still in Chinese and I cannot see a way to change them.
Some lag on boot up lasting for a while but appears to stop until put in sleep mode which starts again for a while.
As mentioned above a freeze/crash and black screen then remained after the sleep mode kicked in. Had to long-hold power to turn it off, when I switched it back on, it seems back to normal. I suspect this was caused by some app or other one of my kids installed.
Hopefully I can get this update done and see if things are better and if not, consider a rom replacement. #reboot required now as the windows installer is playing up as I cancelled the first pheonix installer to look for any newer and english version. Back later today.
Edit :
Managed to get through the firmware update and am now going to check it out to see if anything has improved. I think it may be best to give this a couple of days of letting the kids do their thing as well as my own. Of course I will update this again.
update : So after a few hours letting the kids do stuff and having a bit of a play myself, this firmware update really has improved the tablets running qualities. For example, the usage immediately after boot / browsing / gaming / pattern and face recognition unlock all seem to run flawlessly now. The face rec unlock used to sometimes not even load and go str8 to pattern, 30% of the time it wouldn't recognise me and was laggy to happen in most cases. This now runs rapid, loads every time and I think due to lighting and moving around the room, only failed to recognise me, once out of around 10 tries. I tried a game or two with the kids and found reactions were spot on every time, to screen touches. The kids felt it was running nicely now too.
Again, if I find anything contrary to this, i will add another update below.
http://s12.postimg.org/tsh261hl9/IMG_20130801_010116.jpg
At the moment, the tablet doesn't seem to be bloated with much un-needed software although I could probably look deeper and find some. Hwoever this is the part that is something I would love to know how to get rid of or change and is making me think about custom roms, if you look at the image above.
codQuore said:
s12.postimg.org/tsh261hl9/IMG_20130801_010116.jpg
At the moment, the tablet doesn't seem to be bloated with much un-needed software although I could probably look deeper and find some. Hwoever this is the part that is something I would love to know how to get rid of or change and is making me think about custom roms, if you look at the image above.
Click to expand...
Click to collapse
just change launcher.
apex launcher or other
---------- Post added at 06:09 AM ---------- Previous post was at 05:19 AM ----------
Can you tell us number build?
i dl file but seem to be old version.
bosondehiggs said:
just change launcher.
apex launcher or other
---------- Post added at 06:09 AM ---------- Previous post was at 05:19 AM ----------
Can you tell us number build?
i dl file but seem to be old version.
Click to expand...
Click to collapse
Can you tell me more about this launcher and what it does ?
The build number is in the .img filename above
------ and contains >>>> aimei_anpei8003_a31s_v2.0_4.1.1_20130429_[1024x768_ctp兼容_双Camera0308_gsensor兼容_ddr360].img
Ah I see your point... The sites homepage lists them with a different date so I'm not sure which one is correct.
szampe.com/en/index.asp
[Drive Download] A8003QD Ampe Firmware Update - 2013/7/24
Click to expand...
Click to collapse
see this:
http://gizmodo.com/six-android-launchers-to-supercharge-your-smartphone-804826752
i want to know build number when installed.
My original rom have fiber_8003-eng 4.1.1mater 20130517 test-keys
I thin A85 is for chineese market and A8003is for international.
bosondehiggs said:
see this:
http://gizmodo.com/six-android-launchers-to-supercharge-your-smartphone-804826752
i want to know build number when installed.
My original rom have fiber_8003-eng 4.1.1mater 20130517 test-keys
I thin A85 is for chineese market and A8003is for international.
Click to expand...
Click to collapse
I'm looking at various launchers at this moment. I'm toying with the idea for now.
The build number even though dated last week on the offiicial site for this tablet, is
fiber_8003-eng 4.1.1 MASTER 20130427 test-keys as shown in the img filename
I'm a little confused as to what has happened here. I checked the img file modified date on my pc and it indeed says it was last modified in April. Whatever has happened, the tablet is running much better, noticed by myself and the kids, so far.
thanks.
Maybe before you have an old firmware.
I try to install on mine but impossible , i don't remember message.
here is my rom original http://www.szsanei.com/support_down.asp?id=1056
if you want to try.
a85
hi i have the a85 with the a31s chip my device only has 8gig rom where the device description on your link says 16gig apart from that i dont know if there is anything different can i use this rom on my device or is there a risk of bricking the tablet
http://www.szampe.com/support_down.asp?id=1259
anyone tested the new firmware?
MataPollos82 said:
anyone tested the new firmware?
Click to expand...
Click to collapse
I am now still running the 24/July rom I found (see post one) and it seems better but not perfect. It seems like a need for TRIM as regards the problems with lag and crashing (trim or not, I am unsure of crashing part) when I reboot the tablet most problems are solved.
I do think we could do with a better rom, to be honest. I have not tried the roms mentioned by others on this thread.
Name: N83 quad-core version of the firmware
http://www.szsanei.com/support_down.asp?id=1056
Click to expand...
Click to collapse
for example.. I am not sure if I should try it, weary of deeper problems. I am a novice in the rom arena.
bosondehiggs said:
http://www.szampe.com/support_down.asp?id=1259
Click to expand...
Click to collapse
Hi. Since I last posted, my tablet seems to have nose dived into regurgitated mdoe. I can factory restore it using the Pheonix tool and a rom and it works but then WIFI refuses to enable and not long after changnig the language and disabling pinyin, it simply reboots and stays at the chinese boot up screen. I'm now trying the rom quoted above as it might solve the problem but I think there may be a hardware issue. When I do manage to get it worknig, it states 1GB of memory instead of what it should be, 8GB - tax
I am a little worried now as I have heard returning this tablet to where I purchased it, can be a pointless nightmare which is an awful thought as I have just ordered a dual core for my daughter and that has already had shipping issues that are making it an extra week late already.
I contacted them but either they are ignorant or just plain stupid.
Just got one of these - Few Problems
Hi all, Just got one of these tabs for my little boy but have a few problems.
1: Wifi is extremely poor, I have a N600 router and everything wifi can use it but this tab can only connect if i am in the room
as the router, then its painfully slow.
2: Does this have bluetooth, Downloaded a hardware tester and it says no bluetooth.
Currently running this
Current rom: fiber_8003-eng 4.1.1 MASTER 20130427
Kernel Version: 3.3.0 [email protected]
Firmware Version: 2.0
Android Version: 4.1.1
Model: A85 Q
I have found a newer rom: fiber_8003-eng 4.1.1 MASTER 20130429, anyone tried it, any improvements on the wifi.
George
Can someone who has already flashed new firmware please give me clear instruction on how to do it as I don't understand the Chinese instruction in the manual and the program is also in Chinese so cant tell what I am pressing.
dinislam said:
Can someone who has already flashed new firmware please give me clear instruction on how to do it as I don't understand the Chinese instruction in the manual and the program is also in Chinese so cant tell what I am pressing.
Click to expand...
Click to collapse
update program, or if you don't find how to dl last version it's in english
AMPE internal storage =0 and can't flash rom
I have a AMPE A85Q quad core android tablet running 4.1.1 os. Recently, I rooted the tablet using Z4Root despite warnings from my anti-virus AVG saying that Z4Root is a Malware. (I have used Z4Root before on another tablet before without problem). After confirming that I have temporarily rooted the tablet, I thought I return the tablet back to the original state by unrooting the tablet. Everything works fine until I shutdown and restarted the tablet the next day. The tablet factory resetted itself and I lost all my downloaded applications. I tried to download applications again, and it just hung. I then noticed the internal storage is zero. I factory reset it again via the tablet Settings, but the internal storage remains as 0.
So I started this journey get my tablet to the original state, after 2 days of research and experimentation on that subject matter, I have made some discoveries. There are many android users out there having this problem, ie, Internal storage is 0.
The solution provided by many experience users, appears to be quite simple, just copy /system/xbin/busybox to /system/bin.
As I could not access / directory, so from my PC, I downloaded Root_Explorer_v2.17.2.apk into my extsd card, and using my tablet File Manager to installed it. All went well. I then discovered my tablet does not have busybox installed. I thought perhaps, I can find a busybox.apk, I can install it via the extsd card. No luck, there is no a such apk.
I decided at this point, I must flash my ROM. On the website, they recommend backing all the data and apps before flashing, but I have already lost everything, and I can't install any new applications, so I can go ahead and flash the rom.
Since I'm doing this for the first time, I read many articles on the web. And, yes, there were users out there who had successfully fixed the problem by flashing the Rom.
My tablet rom version is fiber_8003-eng 4.1.1master 20130517 test-keys .
I found this rar from the AMPE home site.
szampe.com/UploadFile/file/2011-08/0335.rar (525MB)
(Chinese characters quoted from user codQuore posting)
The rar file contains
FOLDER : A8003QD 爱魅 改乐投风格、4K不支持4个窗口播放的软件20130427 (translated = A8003QD love charm happy to vote to change style, 4K does not support 4 Window Play Software 20130427)
------ and contains >>>> aimei_anpei8003_a31s_v2.0_4.1.1_20130429_[1024x768_ctp兼容_双Camera0308_gsensor兼容_ddr360].img
FOLDER : 全志A31升级工具安装 (translated = Allwinner A31 upgrade tool is installed)
------ and contains >>>> 升级指南（A31主控）.doc (translated = Upgrade Guide (A31 Master))
------ and contains >>>> PhoenixUSBPro_Cn_V330_20121204.rar
------ and contains >>>> PhoenixSuitPacket-V1_0003Beta.rar
------ and contains >>>> PhoenixSuitPacket.msi
At the same site, I also found the latest ROM 0381.rar (497.07MB) which has the same release date as my ROM. The rar file contains two folders:
FOLDER : A85?|?? contains aimei_anpei8003_a31s_v2.0_4.1.1_20130517.img (789.09 MB0
and FOLDER : -A31??? (As above the ?s represents chinese characters) contains PhoenixSuitPacket-V1_0003Beta.rar and ????A31???.doc (110.5kb)
PhoenixSuitPacket-V1_0003Beta.rar contains PhoenixSuitPacket.msi (12.33mb)
Why they have a rar file within another rar file, I do not logically understand. Maybe that's the reason, I can't get this part to work. I cannot understand the chinese instructions in the doc file.
If they know the recovery process requires a zip file, you would think it would be sensible to upload zip file rather than rar file. Anyway, I unzipped the files from 0381.rar using RootExplorer and copy the img, doc and msi files into a folder called 1dir. I then zipped the 1dir as 1dir.zip. I have to re-zip the files so that the recovery program can find the zip file.
In the tablet Settings>>Backup & reset>>Recovery Mode, I pressed Reboot into the system in Recovery Mode. Using the volume down key moved to highlighted “apply update from external storage” and select 1dir.zip from extsd.
...On my tablet screen display:
Android system recovery <3e>
Android sdk reversion:exdroid4.1.1_r1-a31-v1.36
Volume up/down to move highlight:
enter button to select.
reboot system now
apply update from ADB
wipe data/factory reset
wipe cache partition
apply update from external storage
apply update from cache
Install /sdcard/1dir …
Finding update package...
Opening update package...
Verifying update package...
Installation aborted.
And it jumps back to
reboot system now
Installations aborted. Hmm. Since I am only flashing for the first time, maybe I did not do something correctly.
. I tried removing the doc file and only zipped the img and msi file.
. Tried the earlier version 0355.rar. Same result.
. Tried wiping the cache partition first before flashing. Same result – installation aborted.
. Tried zipping aimei_anpei8003_a31s_v2.0_4.1.1_20130517.img with RootExplorer. Same result.
HELP,Please.
tunflog said:
I have a AMPE A85Q quad core android tablet running 4.1.1 os. Recently, I rooted the tablet using Z4Root despite warnings from my anti-virus AVG saying that Z4Root is a Malware. (I have used Z4Root before on another tablet before without problem). After confirming that I have temporarily rooted the tablet, I thought I return the tablet back to the original state by unrooting the tablet. Everything works fine until I shutdown and restarted the tablet the next day. The tablet factory resetted itself and I lost all my downloaded applications. I tried to download applications again, and it just hung. I then noticed the internal storage is zero. I factory reset it again via the tablet Settings, but the internal storage remains as 0.
So I started this journey get my tablet to the original state, after 2 days of research and experimentation on that subject matter, I have made some discoveries. There are many android users out there having this problem, ie, Internal storage is 0.
The solution provided by many experience users, appears to be quite simple, just copy /system/xbin/busybox to /system/bin.
As I could not access / directory, so from my PC, I downloaded Root_Explorer_v2.17.2.apk into my extsd card, and using my tablet File Manager to installed it. All went well. I then discovered my tablet does not have busybox installed. I thought perhaps, I can find a busybox.apk, I can install it via the extsd card. No luck, there is no a such apk.
I decided at this point, I must flash my ROM. On the website, they recommend backing all the data and apps before flashing, but I have already lost everything, and I can't install any new applications, so I can go ahead and flash the rom.
Since I'm doing this for the first time, I read many articles on the web. And, yes, there were users out there who had successfully fixed the problem by flashing the Rom.
My tablet rom version is fiber_8003-eng 4.1.1master 20130517 test-keys .
I found this rar from the AMPE home site.
szampe.com/UploadFile/file/2011-08/0335.rar (525MB)
(Chinese characters quoted from user codQuore posting)
The rar file contains
FOLDER : A8003QD 爱魅 改乐投风格、4K不支持4个窗口播放的软件20130427 (translated = A8003QD love charm happy to vote to change style, 4K does not support 4 Window Play Software 20130427)
------ and contains >>>> aimei_anpei8003_a31s_v2.0_4.1.1_20130429_[1024x768_ctp兼容_双Camera0308_gsensor兼容_ddr360].img
FOLDER : 全志A31升级工具安装 (translated = Allwinner A31 upgrade tool is installed)
------ and contains >>>> 升级指南（A31主控）.doc (translated = Upgrade Guide (A31 Master))
------ and contains >>>> PhoenixUSBPro_Cn_V330_20121204.rar
------ and contains >>>> PhoenixSuitPacket-V1_0003Beta.rar
------ and contains >>>> PhoenixSuitPacket.msi
At the same site, I also found the latest ROM 0381.rar (497.07MB) which has the same release date as my ROM. The rar file contains two folders:
FOLDER : A85?|?? contains aimei_anpei8003_a31s_v2.0_4.1.1_20130517.img (789.09 MB0
and FOLDER : -A31??? (As above the ?s represents chinese characters) contains PhoenixSuitPacket-V1_0003Beta.rar and ????A31???.doc (110.5kb)
PhoenixSuitPacket-V1_0003Beta.rar contains PhoenixSuitPacket.msi (12.33mb)
Why they have a rar file within another rar file, I do not logically understand. Maybe that's the reason, I can't get this part to work. I cannot understand the chinese instructions in the doc file.
If they know the recovery process requires a zip file, you would think it would be sensible to upload zip file rather than rar file. Anyway, I unzipped the files from 0381.rar using RootExplorer and copy the img, doc and msi files into a folder called 1dir. I then zipped the 1dir as 1dir.zip. I have to re-zip the files so that the recovery program can find the zip file.
In the tablet Settings>>Backup & reset>>Recovery Mode, I pressed Reboot into the system in Recovery Mode. Using the volume down key moved to highlighted “apply update from external storage” and select 1dir.zip from extsd.
...On my tablet screen display:
Android system recovery <3e>
Android sdk reversion:exdroid4.1.1_r1-a31-v1.36
Volume up/down to move highlight:
enter button to select.
reboot system now
apply update from ADB
wipe data/factory reset
wipe cache partition
apply update from external storage
apply update from cache
Install /sdcard/1dir …
Finding update package...
Opening update package...
Verifying update package...
Installation aborted.
And it jumps back to
reboot system now
Installations aborted. Hmm. Since I am only flashing for the first time, maybe I did not do something correctly.
. I tried removing the doc file and only zipped the img and msi file.
. Tried the earlier version 0355.rar. Same result.
. Tried wiping the cache partition first before flashing. Same result – installation aborted.
. Tried zipping aimei_anpei8003_a31s_v2.0_4.1.1_20130517.img with RootExplorer. Same result.
HELP,Please.
Click to expand...
Click to collapse
Eureka! Fixed.
OK. Before I forget, I better document the fix. The vendor website actually has the img and the tools to flash the rom. Not understanding Chinese user's guide is my problem. Also pictures in the in the instruction shows the use of Livesuit tool instead of PhoenixSuit; this let me needlessly looking for Live Suit software to work with A31. After unzipping the 0381.rar file, there is a img file and a Window installabled msi file, PhoenixSuitPacket.msi. I copied the img and msi files to a directory in my Windows7 PC, and installed PhoenixSuit V1.003Beta. The installation is the tricky bit, because my Windows Installer does not display Chinese Characters. I was desperate enough to click on what I guessed is the "NEXT" button during the installation process. I could read that all installed files were placed in the /program(x86)/Allwinnertech folder. Once installation complete, in the folder there is a pdf file which tells you in Chinese and in pictures, how to use PhoenixSuit to flash the rom. I started PhoenixSuit. There are enough English words and pictures to understand what to do.
I powered up the tablet before connecting the tablet to the PC. The tablet immediately displayed the USB port is connected, and I chose to enable data transfer to storage. At this point, PhoenixSuit also wake up to display the version of firmware, even partially disfunctional, on the tablet. All very positive signs. I proceeded to flash the rom using my img file located in the PC using PhoenixSuit. It took less than 4 minutes, and successfully flashed the rom.
I have rechecked the Internal Storage and it is now displaying 0.99GB instead of 0. Also, Busybox reappears in /system/bin. All good.
Hope this little adventure helps someone out there.
When I'm game enough, I'll tried to re-create the problem. Was it during the rooting process using Z4Root that the problem appears? I will update again when ....
[TUTORIAL][GUIDE]Complete Guide to ROOTING, CWM & ROM(s) for LAVA ETAB XTRON+(RK3066)
Here is a short review first
| HARDWARE |:-: Talking about the Lava Xtron+’s hardware, the tablet boasts a dual core Cortex A9 CPU with each core clocked at 1.5Ghz and a Mali 400 Quad Core GPU.
Well, for the proof of graphics power, see the benchmarks by fonearena.com ,63.9 fps in nenamark, and the most important thing according to me, RK3066 IS THE BEST LAST GEN GAMING CHIPSET BETTER THAN TEGRA 3...I am a true geek and after searching for 20+ hours came to a conclusion that this is the best piece of android till 12-13k,(except Lumia 520 but it is windows)..
| BATTERY | :-:Coming on to battery, When I opened the battery stats page I find that Cell standby had consumed nearly 60% of the battery.WHAT!? Cell standby is the battery used by radio cells for mobile networks. This tablet DOES NOT have cell radio! The engineers working on this tablet didn't even bother to setup the OS properly and instead chose to simply download Android 4.2, flashed it in the tablet and have put it up on sale.
The Flipkart page reports the battery capacity to be 3,700mAh, which is probably wrong since the official specifications page on Lava’s website reports it to be only 3,000mAh. I can't be sure..:silly:
AIRPLANE MODE IS NOT COMPLETELY WORKING DUE TO DEFECTIVE DRIVERS (CELL RADIO DRIVERS ARE PRESENT IN THIS TAB SO IT SEARCHES FOR DRIVERS CONTINUOUSLY AND FUC*S BATTERY UP!:crying There is a fix in the post
| SCREEN |:-:The front of the Lava Xtron+ holds a 7-inch sharp IPS LCD display having a resolution of 1024 x 600. It’s a bright screen and with a pixel density of 170 PPI, it is pretty sharp too. The best part about the display is that, despite being an LCD screen, it’s not a battery consuming monster. I always found its battery usage to be lower than processes. The screen is prone to scratches though and is highly reflective.
We can enable the biggest advantage of PC gaming in android now, i.e 4xMSAA in deveoper settings, makes gaming experience even better than tegra 3
Click to expand...
Click to collapse
Before starting i would say that i am not responsible if any guides here bricks your device ( it should not happen at all if u follow all steps properly as the chances of permanent brick of rk3066 is very slim but boot loop is a possibility) I made this thread to collect everything I've done in one place. This should make everything very straightforward and basically most probably n00b-proof.
| ROOTING | :-:
Pre Requisites-Working drivers (if not then no problem), OEM USB Cable, LAVA ETAB XTRON+, 2 windows apps and PATIENCE
{Screen shots of important steps is in the attachements}
(i) For Drivers download and install moborobo
HTML:
http://download.moborobo.com/download/Client/Moborobo(Moborobo_En_official).exe
(ii) In tablet go to in Settings >developers options and turn it on and enable USB Debugging & before connecting it to your PC go into the tab's
settings again and click on storage.In it you will find 3 dots in top right hand corner.> USB computer connection >Enable Mass storage
Note: DO "NOT" TURN USB STORAGE "ON".(When Connected to PC)
Note: Remove your external SD card before rooting.
(iii) Connect it to your PC and click on refresh and install/find drivers and it will download and install them..(there might be a security warning
about force install) Now, it may not recognize the model no, IMEI and other things and say that the device is JB7+ but the only thing you
should look for to make sure it is the right device is the total size and usage of internal Memory and NAND Flash..
(iii) Now drivers are securely installed and the tab is connected in the right way (there is no OEM (LAVA) drivers anywhere)
Download the zdm (Chinese software) in the attachments (For Every Step first see the screenshot)
Note:IT MAY INSTALL SOME USELESS SOFTWARE ON UR PC AND TAB , BUT IT CAN BE UNINSTALLED.
(iii)) When it detects the there will be something written like this in the bottom right corner :??ROOT : ONE or something like that (not in screen
shots as the tab is already rooted ) but it must be in green colour.This is the confirmation that the device can be rooted.
(iv) Now click on the Root Button in left hand side
(v) Click twice on green (thingy) first where it says ROOT then again for the confirmation popup (says something else but in green box)
(vi) Rooting Process has begun and the tab will restart (my PC is quite fast so it was almost instantly restarted and the Super SU was flashed it may or may not take 2-3 mins)
Note:IT WILL INSTALL SUPERUSER , WHICH IS OUTDATED BUT BEFORE DOWNLOADING OTHER SUPERUSER APP , USE THE ONE PRE-INSTALLED TO UPDATE SU BINARY.
DEVICE IS ROOTED WOOT! WOOT! you can also check by using Titanium Backup or root checker.
Mod Edit: Rooting method also described by Mohd.Anas here: http://forum.xda-developers.com/showthread.php?p=48776299
How to fix battery:-:
Get root explorer open system/app and rename phone .apk and telephonesomething.apk to phone.bak and telephonysomething.bak, you are good to go..
Also, you should change the WiFi scanning interval to 500 I.e 5 min as you really just require one scan when connecting to a known network..change the wifi supplicant scan interval to 500 build.prop
| CLOCKWORKMOD CUSTOM RECOVERY (GENERIC RK3066) 6.0.3.1|:-:
There are 2 methods one is tested by me(both are the same recovery created by the famous user "fun" at androtab.info), it works on our tab because when I opened the kernel.img with a hex editor (like Neo Hex Editor) the first line started with "KRNL" so I have a dedicated kernel in the kernel partition and I can just use the generic CWM. You can also follow this procedure just to be sure..make a online nandroid backup find kernel.img and open it up in pc in hex editor..
(A)METHOD TESTED BY ME
(i) Firstly you have to get the arctools apk,either by registering at their forum..
HTML:
http://www.arctablet.com/blog/forum/arctools-application/clockworkmod-cwm-recovery-easy-install-on-rk3066-and-rk3188-devices/
(ii) Click on download and select RK3066 CWM fun androtabinfo 6.0.3.1, there is only one option like that so it may or may not be in order.
(iii) Afer downloading click on install apps give i superuser permission and Voila! CWM.
(iii) You should also see the log right in the middle of the apps to verify that the flash and push thingy worked correctly with no errors
(iii) Select Reboot to recovery or Turn the tab off and press power button+vol up and the recovery should open
YEAH! YOU NOW HAVE COMPLETE CONTROL OF YOUR TAB
(B)METHOD NOT TESTED BY ME
HTML:
http://androtab.info/clockworkmod/rockchip/
(i) DOWNLOAD RK30GENERIC_CWM.zip from
HTML:
http://androtab.info/clockworkmod/rockchip/
(ii) Here are the different ways to flash this zip file
HTML:
http://androtab.info/clockworkmod/rockchip/install/
|CUSTOM ROM(s)|:-:
There is only one ROM which is worth flashing and even that might be slightly buggy..
Well, I don't recommend to flash a custom ROM here as they may have bugs like Wifi still if you want the following features
Auto Install Feature: This allows you to install apk's automatically on first boot, if you have the apk files located in a folder named autoinstall on your external SD card.
HTML:
http://www.freaktab.com/showthread.php?8910-Auto-APK-Install-Feature
Rooted with SuperSU
Debloated of all Lava bloatware
Google Play Store tweaks added to improve availability of apps
Init.d support
Busybox support
English language default (all other languages are still supported)
Boot screens by Tattman65
Flash Tool by Finless
Reboot app by Petrus
Here is Lava Xtron+ RileyROM 1.1
HTML:
http://www.freaktab.com/showthread.php?10688-Lava-Xtron-RileyROM-1-1
Complete flashing procedure in extreme detail is in the ROM zip file (it is a PDF file named first time user guide , very helpful)..Personally I have not flashed the ROM as I don't think it is worth the hassle and possibility of no Wifi...
PLEASE CLICK ON THANKS IF I HELPED YOU, IT REALLY MOTIVATES ME!:highfive:
Thank you.. I was waiting for a method to crack this tab.. Will comeback with result.
Ext4 support
Can somebody tell me if ext4 is supported or not, when i try link2 sd it says not supported but I am pretty sure that the system partition itself is Ext 4, (I'm the one who made the guide)
Try ext3. It will be supported.
Prince.Paul.K said:
Try ext3. It will be supported.
Click to expand...
Click to collapse
Well, I have tried it there are some problem in link2sd, but according to an nandroid the system and data are ext4 , I have set up everything in ext2 and would hate to do it all over again, is there a way to verify support of ext 3 or 4 acc to wiki, kernel above 2.6 support ext4 and the kernel here is 3.0... One more ting, when I tilt the tab, I think that something heavy is moving around inside slightly, probably battery should I ask for a replacement? I have 4-5 days remaining I bought from flipkart, I do have a complete SD and nandroid backup..
EDIT: in d/tracing events ext4 there is a file called enable and the value inside is zero should I change it to 1
I think I found out the culprit, the first partiton that I tried was ext2 so link2d created a script for that..now, when I try to use ext3 or 4 ..it still tries to use that same script..so I willl delete the script then try again...
Successfully Rooted..! Sorry for the delay..!
Bro how to stop the battery draining in stand by due to deffective drivers as u say . I cant find the solution in this thread
HTC.EXPLORER said:
....
DEVICE IS ROOTED WOOT! WOOT! you can also check by using Titanium Backup or root checker.
Mod Edit: Rooting method also described by Mohd.Anas here: http://forum.xda-developers.com/showthread.php?p=48776299
How to fix battery:-:
Get root explorer open system/app and rename phone .apk and telephonesomething.apk to phone.bak and telephonysomething.bak, you are good to go..
| CLOCKWORKMOD CUSTOM RECOVERY (GENERIC RK3066) 6.0.3.1|:-:
There are 2 methods one is tested by me(both are the same recovery created by the famous user "fun" at androtab.info), it works on our tab because when I opened the kernel.img with a hex editor (like Neo Hex Editor) the first line started with "KRNL" so I have a dedicated kernel in the kernel partition and I can just use the generic CWM. You can also follow this procedure just to be sure..make a online nandroid backup find kernel.img and open it up in pc in hex editor..
(A)METHOD TESTED BY ME
..../QUOTE]
ukstillalive said:
Bro how to stop the battery draining in stand by due to deffective drivers as u say . I cant find the solution in this thread
Click to expand...
Click to collapse
Click to expand...
Click to collapse
HTC.EXPLORER said:
HTC.EXPLORER said:
....
DEVICE IS ROOTED WOOT! WOOT! you can also check by using Titanium Backup or root checker.
Mod Edit: Rooting method also described by Mohd.Anas here: http://forum.xda-developers.com/showthread.php?p=48776299
How to fix battery:-:
Get root explorer open system/app and rename phone .apk and telephonesomething.apk to phone.bak and telephonysomething.bak, you are good to go..
| CLOCKWORKMOD CUSTOM RECOVERY (GENERIC RK3066) 6.0.3.1|:-:
There are 2 methods one is tested by me(both are the same recovery created by the famous user "fun" at androtab.info), it works on our tab because when I opened the kernel.img with a hex editor (like Neo Hex Editor) the first line started with "KRNL" so I have a dedicated kernel in the kernel partition and I can just use the generic CWM. You can also follow this procedure just to be sure..make a online nandroid backup find kernel.img and open it up in pc in hex editor..
(A)METHOD TESTED BY ME
..../QUOTE]
Click to expand...
Click to collapse
you can also change wifi_suppliant_scan interval to like 150 or so, the default value is very less "20" :good:
Click to expand...
Click to collapse
Going to fix battery
Sent from JB 7+ using tapatalk
nitinchamp said:
HTC.EXPLORER said:
you can also change wifi_suppliant_scan interval to like 150 or so, the default value is very less "20" :good:
Click to expand...
Click to collapse
Alright I know this is a stupid question but..Does it continue to scan when it is connected to a WiFi network..I have also disabled the network norification and enable WiFi optimization...and thanks for the tip..ideally you should only turn scanning on when you want to connect
Edit: added your tip to guide will clean it up when I will use pc
Click to expand...
Click to collapse
HTC.EXPLORER said:
nitinchamp said:
Alright I know this is a stupid question but..Does it continue to scan when it is connected to a WiFi network..I have also disabled the network norification and enable WiFi optimization...and thanks for the tip..ideally you should only turn scanning on when you want to connect
Edit: added your tip to guide will clean it up when I will use pc
Click to expand...
Click to collapse
it still does scan for networks to see what other networks are present
there was also another method to root this tablet which i found back in december mentioned here
Click to expand...
Click to collapse
help
bro i have installed riley rom for lava xtron + tab but now i came to know that wi fi hotspot is a major bug for this rom and the rom is actually the copy of stock rom so i want to flash the stock rom again but cant ,,, so plz help me i have the stock rom zip file , now what to do ?/
plz reply :crying::crying::crying::crying::crying:
ukstillalive said:
bro i have installed riley rom for lava xtron + tab but now i came to know that wi fi hotspot is a major bug for this rom and the rom is actually the copy of stock rom so i want to flash the stock rom again but cant ,,, so plz help me i have the stock rom zip file , now what to do ?/
plz reply :crying::crying::crying::crying::crying:
Click to expand...
Click to collapse
Well you are familiar with cwm or do you even have it installed, if you do then just go to install zip from sd card and select the zip file...secondly if you have a cwm nandroid backup (recommended) just go to backup and restore select resotre or restore from externel sd and then select the date of the required backup file then click restore..If you do have a cwm nandroid backup then it MUST work...if you don't even have the recovery then, ist step is to install it through THE guide then, try to do the ist (not recommended) option...
I have cwm installed on my tablet but i dont have stock rom of lava xtron plus
ukstillalive said:
I have cwm installed on my tablet but i dont have stock rom of lava xtron plus
Click to expand...
Click to collapse
Did you make a nandroid cwm backup before flashing ROM?
Also can you make the account as soon as possible
CM10 for Lava Xtron +
nitinchamp said:
HTC.EXPLORER said:
you can also change wifi_suppliant_scan interval to like 150 or so, the default value is very less "20" :good:
Click to expand...
Click to collapse
http://www.slatedroid.com/topic/41777-romcyanogen-10-for-rk3066-wip/
Check this thread is it possible to flash this on lava xtron + . Can any1 reply plz
---------- Post added at 03:46 AM ---------- Previous post was at 03:43 AM ----------
I have installed cwm in many devices before but first time in my tab and bro i dont hqlave a nandroid back of my stock rom
Click to expand...
Click to collapse
ukstillalive said:
nitinchamp said:
http://www.slatedroid.com/topic/41777-romcyanogen-10-for-rk3066-wip/
Check this thread is it possible to flash this on lava xtron + . Can any1 reply plz
---------- Post added at 03:46 AM ---------- Previous post was at 03:43 AM ----------
I have installed cwm in many devices before but first time in my tab and bro i dont hqlave a nandroid back of my stock rom
Click to expand...
Click to collapse
Then just take a backup of the ROM you currently have installed (I think Riley) and if the CM doesnt work out, revert back easily..:good: Post your results here
Click to expand...
Click to collapse