Database Info

"Converting data partition..." Problem

Alright, allow me to summerize to you guys the series of screw ups that happened in the day that I've had my captivate.
Basically, it's like this. I got this phone from my brother (it used to be his). Now when I got it, I began basically erasing his contents and setting up mine. The Phone is on the Cognition OS and everything seemed fine.
Now, when I tried to set up my google account, it said I had to do a factory reset, I did that. Then I realized the market place app was no longer there :/
I did another factory reset, still didn't help, and started looking around for info.
I told my buddy this and he said he could fix it. So he get's the update.zip for rooting the phone, sets it up on the SD card, and goes to root the phone normally. Except when he restarts the phone after, it doesn't go to the set up screen, so he just starts it normally and enters the setup screen by holding home+volume up+power.
Then he presses the reinstall packages, and the phone seems to get to work on the update pack...
Now, every time I turn on the phone the voice says "converting data partition to optimize extension four", turns off, then repeats.
I've looked up this problem and it seems to have something to do with voodoo, but the causes in the other cases the causes were different.
Can someone please help me out here? I've also tried doing a hard reset by holding the volume down button and pressing power, but nothing seems to take me to the recovery mode.
HELP.

Did you pull the battery during this our did you let it run? Should let it run.
Does your phone boot up at all?
At&t or rogers?
Do you have a windows pc with usb drivers installed?
What its your build number, located under battery, something like 1008?
Answer these questions and we can get you back up and running

-Well after he did the reinstall thing we let it run for like 15 minutes, then he pulled the battery out.
-The phone only shows the AT&T screen, say's the "converting data partition..." thing, then goes blank and does it again. I've let it run for like 10-15 minutes before having to turn it off because I couldn't have the speech going off.
-I have a windows PC, and but I'm not sure if I have the drivers installed. I have Kies installed and when I plugged the phone in before Kies could recognize the phone (though it wouldn't fully connect, it would just say "connecting" on the kies screen).
-The Model is SGH-I897, that's the only relevant thing I see under the battery, that good enough?
Thanks a lot.

No, your phone has a build, on phone under battery, the word build is not listed. Something between 1006-1012
If we are going to do this you need to be active, I can not wait 20 minutes in between responses

Sorry the internet kinda crapped out actually.
And I see a 1007 between the bar codes, that it?

Yes
Before we get started try this
Take battery, sim, ext sd our of phone
Plug usb into pc but not phone
Put battery back in
Hold volume up and down, while holding plug in usb
Screen should come on with android with shovel
You can pull the battery again
Confirm this happened

Yep, it happened.

It may be easier if we use gtalk, log in on your pc using google id, send me an invite [email protected]. This way we know when each other respond

Just sent u the inv

I am having the same issue.. Chairchair did your problem get resolved?
Can anyone help?
James

liquorsh0tz said:
I am having the same issue.. Chairchair did your problem get resolved?
Can anyone help?
James
Click to expand...
Click to collapse
Have you gone back to stock and then reflashed? Seems like some files are getting corrupted. Because you have a voodoo kernel I would follow these steps. Make sure to back up.
1. Use Odin to flash a non vodoo kernel.
2. Flash stock rom and master clear
3. Reflash rom of choice if it is 2.2
3a. If you want 2.3 follow the tut on it.
4. Breath a sigh of releive lol

G2x continuously rebooting the lg logo screen

My phone runs perfectly fine until I enable Gps location. Once I enable GPS location, it freezes, then it reboots my phone and it slowly do a system check, then it continuously rebooting the lg logo screen. I tried taking out the battery and put it back in, even took out my battery for a day and it still does the same. I'm not sure if it's the hardware problem, but it's a pretty rare case, since I read most of the threads in forums, people said it can be fix once you pull out the battery, but somehow it's not working for me. Anyone knows the reason why? Btw, my phone is not rooted or used any 3rd party program.

Ah. Posted too soon. There's a master reset that I believe is Power and Volume Up. Try that.

Unfortunately, it's still not working. Is there any other possible way? Or else I have to call in and return it.

Try turning off the phone, then press power + vol down and hold it until you see the word android. This should do the factory reset.

efrem989 said:
My phone runs perfectly fine until I enable Gps location. Once I enable GPS location, it freezes, then it reboots my phone and it slowly do a system check, then it continuously rebooting the lg logo screen. I tried taking out the battery and put it back in, even took out my battery for a day and it still does the same. I'm not sure if it's the hardware problem, but it's a pretty rare case, since I read most of the threads in forums, people said it can be fix once you pull out the battery, but somehow it's not working for me. Anyone knows the reason why? Btw, my phone is not rooted or used any 3rd party program.
Click to expand...
Click to collapse
It sounds like the permissions are not correct, or perhaps that your ROM was not flashed correctly. I have seem this problem happen numerous times due to bad firmware flashes or ROM issues. I would just download a new copy of the latest CM 7 ROM or whatever your favorite ROM is and flash it through CWM.

Thanks guys for the help. I found out that you have to hold down first then power button for around 30 second and then the droid animation comes out. I was so close to returning it. Thanks!

Volume + Not Working?

I recently updated my TF to 8.6.5.19 Firmware With CWM & Root and I noticed my volume up is not working, the down works fine, I have tried rebooting, Factory Reset and still nothing. It worked fine when I did the update with CWM but now it just stopped. I am not sure if it is software or hardware, I tried rebooting into CWM and it will not work either. I also noticed the backing has separated from the bezel and you can see the rubbers around the volume keys, I have never noticed and issue before with the volume, the volume down seems soft to press as the volume up seems a little bit harder. I wanted to send it for RMA but It is rooted and I do not know how to unroot it. I was told by someone that ASUS will not fix it if you root the tablet. If anyone can let me know what I could do to fix it or maybe someway to reflash the update again or unroot it. I would greatly appreciate it.

A solution....
Well i guess not many people can help you if they dont get the hands on it. Usualy u cant find out if it works or not. Best way is plug it in your pc open properties on your computer and go to hardware and see if the APX activates this is how u can find out if it really work if not here you have a program to get directly to recovery ...
---> https://market.android.com/details?id=com.modaco.transformerrecoveryboot&feature=search_result#?t=W251bGwsMSwxLDEsImNvbS5tb2RhY28udHJhbnNmb3JtZXJyZWNvdmVyeWJvb3QiXQ..
It works fine because i have tried it...

I have tried to get into APX mode many times but it does not work, it just starts the tablet, It is installed on my PC for I have used it before numerous times to install updates and to root it. The only option I can get is the volume down menu which I cannot select "Up" so it boots to the Wipe Data/Android screen. I want to RMA it but I cannot get anyone to let me know whether they will fix it if it is rooted.

This isn't going to help you much but I had an identical problem where the volume Up button stopped working. It was the impetus for me finally sending the unit in for repair - came back a month later with the volume up button functioning but the power button broken and the entire unit virtually unusable. This was a hardware repair as they did something to make the button feel totally different. Second RMA did fix things though.
Mine wasn't rooted though - way too many issues on this thing for me to risk the warranty. Good luck to you though.

Well I bought and downloaded the Asus Transformer Recovery Boot and it works like a charm for getting me into CWM but still no APX mode

Im sorry but i only want to help...
I insist please turn off your TF plug in usb to pc then turn it on pressin VOL + and START and go to mi pc properties hardware and u will see it goes in apx keep trieing it has to work sometimes it takes a little the screen on TF is black all the time just look at pc do it and wait count at least 8 seconds before letting loose the power bott and not more than 10 secs the VOL + if u do it wont work... TRUST ME ON THIS i have tried it on a TF 101 and a TF 3G both rooted now...

[Q] Nexus S i9020A Bricked due to failing power button - Odin seems the last hope?

Hi everyone,
INTRO:
So the power button on my Nexus S broke. No big deal, I remapped it to the search button and used the volume rocker to wake the device; an option that was embedded in Cyanogenmod9.
Then I upgraded to CM10... since I did that on top of CM9, my volume rocker option was still enabled, but the option is no longer in CM10's GUI.
I had some annoying issue and thought maybe I should wipe my phone; which I did.
Sadly, I realized that my "wake using volume rocker" option was no longer enabled, and there is no GUI to turn it back on.
I then found a .zip package that was supposed to enable the option but, I guess I went too fast, now my phone is stuck on a bootloop.
THE PROBLEM:
Since my power button is broken, I cannot navigate in the fastboot menu to recovery and fix the ROM.
Worst, since the power button is somehow shorted (i.e.: it powers on automatically when I insert the battery) Fastboot is not working properly and my PC never sees my phone, so you can forget about fastboot boot recovery.img
So: boot loop, power button broke, no recovery, no fastboot. =(
I searched quite a bit and found out you could get the Nexus S in download mode and get it to work with ODIN using a USB JIG.
I made myself such a JIG and successfully put the phone in some kind of download mode where my PC sees it, fastboot devices yields nothing *but* ODIN sees the phone!
So a glimmer of hope except for the fact that finding the .tar files for the Nexus S seems impossible...
Thoughts? Suggestion? TIA!
Francis // XC3N

Oh BTW:
-Yes I saw the other posts, but none of them mention the odin files
-Yes, I know fastboot is better; but it's not working and:
-No, I can't see the device on 3 different PCs using 3 different OSes and 3 Different cables when in fastboot mode
I mean by that last line that *nothing* shows in device manager in Win7 or XP and *nothing* shows in lsusb on ubuntu
So unless someone has an idea it looks like Download mode is the only way my PC sees my phone...

My power button done the same thing, I googled around and found a solution that worked for me.
It's somewhere here on xda but I don't got the link, basically everytime I booted into the bootloader I couldn't move the cursor with the volume button because the phone thought I was holding the power button, so I carefully tapped the casing around the power button and rebooted the bootloader and eventually I had control, it took 5-6 attempts to get it going but it did fix the power button for me.
I think it's something to do with the micro switches giving out after a certain number of uses.
Also it started screwing about recently so I just blew into the casing through the power button and it's behaved ever since.
In short, tap it until it works, once you have control of fastboot plug the usb in and your pc should detect it
Hope this helps, Good Luck
Sent from my U20i using xda app-developers app

Muckyfox said:
My power button done the same thing, I googled around and found a solution that worked for me.
It's somewhere here on xda but I don't got the link, basically everytime I booted into the bootloader I couldn't move the cursor with the volume button because the phone thought I was holding the power button, so I carefully tapped the casing around the power button and rebooted the bootloader and eventually I had control, it took 5-6 attempts to get it going but it did fix the power button for me.
Also it started screwing about recently so I just blew into the casing through the power button and it's behaved ever since.
Click to expand...
Click to collapse
Hey MuckyFox thanks for your reply!
Unfortunately, that would've worked back when the power button was flimsy and still working once in a while... I did try the tapping thing but really nothing works... the button seems entirely dead and shorted. I guess at this point I might've to bring it in for repair... if the power button isn't broken then I'll be able to easily fix everything in recovery or fastboot. Sucks because I feel like I'm so close to getting it to work without spending money XD I just can't find the files for odin even though they really do seem to exist.

Allright so I found some odin files which were said to work with the i9020a
I flashed them... at some point it said "RESET!" and then odin no longer saw the device. The device is now not booting at all. FML

So this thread is going to end up like every other similar thread: I went and bought a Galaxy Nexus ;P
For posterity, these are the files you shouldn't flash on i9020A:
BOOTLOADER : Bootloader_I9020XXJK1.tar
PDA : PDA_SOJU_GRH78_85442_SIGNED.tar
PHONE:
CSC : CSC_I9020_EUR.tar

My power button started failing over the last couple of days. First when I would set the phone to standby it would ask me if I wanted to switch off the device, then later on it wouldnt respond at all.
Really weird solution - boot into recovery, factory restore, clear dalvik cache, voila, works good as new! (aside from losing all my settings)
Note, I barely managed to get into recovery. The power button fully stopped working halfway through and I had to take the battery out and try it a couple of times.
Oddly, even during this uber-broken phase, the power button would always switch on the device when fully switched off (not just standby) indicating to me that it wasnt just a physical broken connection.

I've mentioned this before, but a full casing for the phone with all the buttons is around $10 on eBay
Sent from my Nexus S using xda app-developers app

XC3N said:
So this thread is going to end up like every other similar thread: I went and bought a Galaxy Nexus ;P
For posterity, these are the files you shouldn't flash on i9020A:
BOOTLOADER : Bootloader_I9020XXJK1.tar
PDA : PDA_SOJU_GRH78_85442_SIGNED.tar
PHONE:
CSC : CSC_I9020_EUR.tar
Click to expand...
Click to collapse
You need stuff for SOJUA, and just the fact CSC has EUR meaning Europe in it would scare the crap out of me. Possible you just flashed stuff meant for i9020T and not i9020A.

In case anybody comes back here, I'm just gonna drop this in.

[Completed] Htc One M8 hardware buttons working weirdly

Hello everyone! So I've had my phone (HTC One M8) rooted and custom recovery and rom installed for a little while now. The latest rom I've installed was Android Revolution HD 22.1. I also have twrp 2.8.1.0 installed. The other day my phone got wet and started to constantly reboot itself, wouldn't shut off and stay off, would never actually start. I put it in a cup of rice for 2 days, then proceeded to plug it in to charge it. Once charged enough I tried to turn it on. It only made it the HTC One logo screen and would vibrate every 10 seconds or so. I tried rebooting several times and no matter what I did with different button combinations I could not get it to load into bootloader. Eventually with restarting different ways and "mechanically stressing" the phone (short temper lol) I managed to get it to loading into the rom itself. From there I opened hasoons all in one toolkit to reboot directly into recovery and recovered to the stock rom. So the phone will now reboot with no problem into this rom. I haven't tried reflashing the ARHD 22.1 rom again because im afraid it'll break again. However, while in the stock rom everything work fines except for the volume up button which does nothing, except for while the screen is off, if I turn my phone to landscape the camera app will open without me even pressing the volume up button. If I reboot into bootloader via the quickboot app or hasoons toolkit, my volume down button with make the cursor go up, the volume up button does nothing, and the power button does nothing. The only thing I can do in bootloader is to hold power+volume up to get the phone to reboot. I also cannot get bootloader to load by holding volume down+power. So, After all that explaining, my main question would be, do you think that the buttons are shorting in a weird way because of water damage, or do you think my software got corrupted because of all the rebooting it did? Any help is appreciated, thanks!
-Tim

Hi,
You could try a clean flash of the rom.... If you're sure the wonky buttons won't interfere with the flash, because if they do... You'll be left with no OS on the device.
Water can affect many things, especially with power on while it was wet. This will be hard to solve, and could get costly. Usually with water damage, you fix or replace one thing, only to find now that something else doesn't work. Can turn into a real money pit.
You're issue isn't so bad, but my usual advice for worse cases are save your money for a new device, because you may never get your device fully working and spend a lot of money trying to fix it.
Ah, I just saw you already asked for help in your device section. Good. ?
Then this thread can be closed, as we're here to help navigate the site, not support.
Thank you.