hi guys
i am new to this so apprecaite your help.have been using my xda exec for about a firthinte brilliantly.however since yesterday ,when i plug the usb cable to pda nothing is happening,fone is not being recognized by pc.i tried different cables and diferent pc's to no avail.the pda does not even charge via usb cable.
however it charges normally via wall charger.
do you think I bust the connector,could it be fixed?
grifone said:
hi guys
i am new to this so apprecaite your help.have been using my xda exec for about a firthinte brilliantly.however since yesterday ,when i plug the usb cable to pda nothing is happening,fone is not being recognized by pc.i tried different cables and diferent pc's to no avail.the pda does not even charge via usb cable.
however it charges normally via wall charger.
do you think I bust the connector,could it be fixed?
Click to expand...
Click to collapse
A couple of questions:
What ROM are you using?
What version of Windows is your main computer running?
Has ANYTHING changed between it working and it not? (Automatic updates, new software installed, installed drivers for a new USB device, etc)
Does the PDA recognise that it is charging/has external power?
Can you borrow a different cable\somebody else's computer to test it on?
Just as a test, try going into your settings, in the connection tab and go into "USB to PC". Try ticking\unticking the checkbox labeled "Enable advanced network functionality"
If the cable is broken, best thing to do is to buy a new one - its probably not worth the money to repair it (try looking on EBay - any mini-usb cable SHOULD suit the Universal)
(ps. are you sure you should be posting in here? I think you probably should have put it into the main section for Universals)
hi TehPenguin
thx for your reply
as i said before i am a total newbie and so dont know were to check wot ROM i am using.from where can i check.the fone come with WM6 installed(it does not have video calling however)
i am runnig windows xp sp2 on my pc.
when i plug in wall charger ,pda recognizes it
no mew software were installed from the time it was working(after that i installed a couple of spb programmes via bluetooth)
i tried my cable on my fiends foned and it worked,i tried my fone with my friends cable and it didnt work,that is why i am thinking it is something to do with my mini usb connector.
can some admin move this post to appropriate section or do i repost there again?
tnx again
grifone said:
hi TehPenguin
thx for your reply
as i said before i am a total newbie and so dont know were to check wot ROM i am using.from where can i check.the fone come with WM6 installed(it does not have video calling however)
i am runnig windows xp sp2 on my pc.
when i plug in wall charger ,pda recognizes it
no mew software were installed from the time it was working(after that i installed a couple of spb programmes via bluetooth)
i tried my cable on my fiends foned and it worked,i tried my fone with my friends cable and it didnt work,that is why i am thinking it is something to do with my mini usb connector.
can some admin move this post to appropriate section or do i repost there again?
tnx again
Click to expand...
Click to collapse
Okay, Windows XP is a good start - and its nice to see that you did some test to figure out where exactly the bug is
I find it unusual that your phone came with WM6 already on it - unless it was second hand... You can check your windows version by going into the settings, under the "System" tab and opening "About", at the top of this it should have "Windows Mobile(R) 6 Professional" or something like that
Here are some more things to try:
Have the phone off and disconnected, then plug in the cable (this seems to work for me if I have problems)
Go into your settings, under the connection tab and go into "USB to PC". Try unticking the checkbox labeled "Enable advanced network functionality"
I think that the second one is most likely the way to fix it. Also what version of ActiveSync are you running (At the top of ActiveSync there is a "Help" menu, select the "About Microsoft ActiveSync" - this should give you version info). If the activesync is anything less than version 4.5 - look for an update on Microsoft's website
And one last thing - no offence, but - one thing I don't like is people using "IM spk" for forums. I understand if you aren't fluent in English but please try...
Enjoy!
TehPenguin
thanks again for your help.
first I would like to say that i do not know what you mean by IM spk ?sorry if I broke any rules
the phone is not new,i bought it off e-bay
I am running activesync 4.5 on my pc which if i am not mistaken is the latest version available.
I will check about what version i have later,as I dont have phone with me currently,but what I can say is the version i have does not support video calling,and it does not have the Phone pad facility in the entering text options.
No harm done with the "IM spk" (its just one of the things I don't like - I'm sure you read my post on the Ultimate ROM)
Did you try any of my other suggestions?
Also, you may wish to upgrade your Universal to a new ROM (I believe that Ivan is uploading one as I type) or go to an official WM5 ROM from a manufacturer - it is possible that the ROM you are using is defective...
just to let you know
problem fixed.it was a hardware problem after all,took it to a local technician who fixed it up for me
all back to normal now
thanks for your help m8
connector broken
The connector on side of my universal appears to have come dislodged and can't charge
How I repair usb connector?
i viewed:
http://forum.xda-developers.com/showthread.php?t=242772&highlight=connector
http://forum.xda-developers.com/showthread.php?t=242772&highlight=connector
others solutions?
thanks
That's for a Wallaby. The Uni has a USB socket soldered straight to it's mobo. It depends if the damage has ripped any tracks from the mobo. It may be a straight solder replacement, or you may need to follow the tracks slightly to solder further along them. I'm sure a competent solderer would be able to help if you showed them it. Or upload a picture of the damage and we can all have a look
Hi folks.
My Tornado (imate sp5) was flashed from factory WM5 to WM6 with VJ Grace 3.3, it worked just fine. One day I lost conenctivity via activesync over the usb cable. BT activesync still works fine. I had not done anything to the connecter port other than using USB cable to activesync occasionally, and to use the wall charger.
After 2 months of going like this, I decided to upgrade to a newer Nitrogen ROM, and I enter the bootloader mode by pressig the camera button and plugging in the usb cable. The three color screen comes just fine.
Now, when I attach the USB cable, I do not see the small writing "USB" at the lower left hand corner.
Also I cannot connect it with Terraterm pro or the RUU utility, says phone is not connected via the USB.
But my usb cable still charges the phone when connected to the PC, even though activesync doesnt do anything.
Is there anything I can do?
Can it be a hardware error? Or a registry change I might have done using smarttweaks (enable/disable charging over usb-- I dont remember). If so can it be restored or undone?
I tried hard resets (clear storage and leftsoftkey/rightsoftkey/powerbutton combinations), but still it doesnt recognise activesync.
My other windows mobile devices get connected to same pc activesync with no problem, using the same data cable. Heck I even repaired by reflashing a friend's Wizard using the same pc and cable last week.
Is it possible that my tornado's usb connector port might have gone poof (it still charges the phone), and is there any remedy to that?
Thanks for reading, and please help..
Regards,
Steve
I've got the same problem. I can't connect via AS:/
I had a similar problem once in a while when I upgraded my phone to WM6; it seemed almost random. One day, the phone wouldn't switch out of Vibrate mode, and ActiveSync wouldn't synch with the phone. The first time it happened, I had VJGrace's 3.3, and 3.4 had just come out, so I went ahead and flashed it. I didn't format binfs or anything (which, in my experience isn't necessary for a functioning OS flash, just a clean one) but it flashed a fresh WM6 on, and the problem went away.
Then, a couple weeks later, I had the same problem again. It was right around the time that VJ's 3.7 came out, so I flashed that (again without format binfs) and it fixed the problem again.
Then, a couple weeks later, I had the same problem yet again. This time, Nitro's Platinum Edition had just come out, so I flashed it. Haven't had the problem again.
Interesting note - since I got my Tornado, my first Smartphone, I have only ever done the format binfs once - the first time I flashed WM6. Haven't done it since. It's my opinion that format binfs gives you a CLEAN install of WinMobile, but is not strictly necessary.
So, to summarize: try direct-flashing a new WM6 install. Just plug in the USB cable - ignore ActiveSync when it fails to synchronize - and run the updater program. It'll take care of the rest, even if AS doesn't synch.
djsleepwalker:
If you lost USB connectivity, how did you flash your phone?
Should I read between the lines that the bootloader connected properly and that it was a WM6 driver problem?
Exitao said:
djsleepwalker:
If you lost USB connectivity, how did you flash your phone?
Should I read between the lines that the bootloader connected properly and that it was a WM6 driver problem?
Click to expand...
Click to collapse
To be totally honest, I'm not 100% certain. See, ActiveSync wouldn't SYNCH with the phone, but I could still "Explore" the phone. WM6 was active and working, and charged via USB cable, it just wouldn't synch.
So, after I connected the USB cable and ActiveSync popped up a message that said it couldn't synchronize with the phone, I just started up the ROMUpdateUtility program. It rebooted the phone into the bootloader for me.
I honestly never tried to start it back up in bootloader mode. The only reason I decided to just flash a new ROM was because I had already downloaded the ROM, but where I was at the time, I had no internet access (and therefore couldn't remember the steps before flashing the new ROM.) A friend of mine who has a Wizard (and who, I think, might be a member of this forum) suggested that I didn't *have* to format binfs to put an updated ROM on the phone, so I said screw it. I needed it out of Vibrate mode (my phone is my second alarm - my second line of defense against oversleeping) so I flashed the new ROM.
ninja edit: If ccpraveen is getting *nothing* when he connects the USB, then my suggestion probably won't help. But if Windows recognizes something being connected, and he can *explore* the phone, but ActiveSync just won't synchronize, then he's probably having the same problem I was. I can't tell for sure from reading his post.
Sweet...
Thanks for the comments, its all dejavu again
Djsleepwalker's comments did make me wonder, hey this is exactly my problem, except that mine doesnt connect in any manner.
Lots of similarities, problems started with VJ 3.3, on and off for a while with USB, then totally lost connection.
I am not concerned with formatting BINFS now, I somehow want to get the phone recognized.
Exitao has actually asked a VERY VALID query. It is indeed impossible to flash a phone without any USB connectivity (unless via an SD image or something). Djsleepwalker's issue was minimal, only that the PC was not showing up the activesync as connected, but indeed there WAS a connection, he could explore the phone from the pc etc, and I bet if he did go into the 3 color screen, he would have seen the "USB" on the left lower portion.
So, mine is just that. No connectivity. Nada. PC just sits dumb. Phone just gets charged, and finally into the fully charged green LED. Thats it.
Could there be something in VJ's ROM that is doing this?
I wonder, because a Wizard I once tried to repair would not let me flash upgrade either. I had to go back to a basic BUTTON ROM to get the upgrades running properly again. But there atleast I had connectivity then.
After I read DJ's comments, I tried running the RUU straight, without getting into the bootloader (for a change). Again its the same error 260. Here is a screenshot.
Anybody?
Regards
Steve
It seems, from the description, that the activesync profile became corrupt.
Deleting any device profiles from Activesync and connecting the phone as a new device might also solve the problem. However, it might be active synch on the phone that is the problem...
Anyone unsure how serious their problem is should just turn off the USB connect in activesync, start the phone into boot loader and do an "info 2" with terraterm pro.
If terraterm discovers the device, the USB is not the problem. It's activesynch.
Terraterm pro would not connect either.
I started the phone into bootloader by plugging in the usb while keeping the camera button pressed. Started the terraterm pro, selected Serial > USB, clicked Ok, Terraterm says ERROR, Cannot Open.
One minor thing, what do ppl normally see in their bootscreens? I see these lines, Tornado IPL 2.00 Tornado SPL 2.00.0000 and another line Tornado IU.
I dont remember seeing this third line saying Tornado IU before. Is it normal? It is in the middle zone( green coloured zone).
I believe my usb connector port might have a physical error. What else it could be. PC just will not detect ANY sort of USB connection.
Thanks again Exitao, I am stumped.
Regards
Steve
Have you tried any other USB ports on your computer? I know it's a longshot, but on my desktop PC one of the onboard USB ports just doesn't function at all. The other three do.
ninja edit: Maybe try it on another computer, too?
I tried on all four USB ports of my laptop, as well as on another Desktop PC I have.
Even without activesync installed, plugging in this should bring out a DING, saying something has been connected to the PC USB. (and asking for drivers, if Activesync was not installed. Here nothing happens, no DING). Remember, the same USB port is being used to sync my Wizard, Blackjack 2 and my old Himalaya even now.
Another possible reason, I was using a dumb chinese charger for charging the phone, after I lost the original one. Could that might have fried the usb pins?
ccpraveen said:
I tried on all four USB ports of my laptop, as well as on another Desktop PC I have.
Even without activesync installed, plugging in this should bring out a DING, saying something has been connected to the PC USB. (and asking for drivers, if Activesync was not installed. Here nothing happens, no DING). Remember, the same USB port is being used to sync my Wizard, Blackjack 2 and my old Himalaya even now.
Another possible reason, I was using a dumb chinese charger for charging the phone, after I lost the original one. Could that might have fried the usb pins?
Click to expand...
Click to collapse
Please excuse me if I'm stating the obvious, or if I'm a bit off, as I don't haven't used my Tornado in a bit (upgraded to Touch Cruise), but in the last ROM I used, NitroGen's latest WM6 version, there was an option in settings to disable usb connectivity and only allow USB charging. Perhaps VJ's ROM has the same option and you activated it. Have you already checked this?
Did you remeber to uncheck "Alllow USB connections" in activesync before you connected the boot-loaded phone?
This may be a hardware problem. Is it possible to use a can of compressed air to blow out any dust or debris from the USB socket on the phone?
Do you have WMStorage on your phone? If not, can you load it onto your storage card and install/run the app and see if the PC will recognise your device as a USB mass storage device?
I guess you also want to check the Device Manager in Windows and check for any exclamaition marks (!) or "bangs." Both with the phone disconnected and connected, and maybe even with wmstorage enabled. If it does show your phone in the device manager, delete or remove the device in the manager and reboot.
(To get to device manager, you can right click on "my computer" and select "properties", or press the Windows key and the Pause/Break key, or go to the control panel applet.)
BTW: is this XP?
If you are using Vista, try the following:
Step 1: Press Start
Step 2: Select settings
Step 3: Select (6) Connections
Step 4: Select (0) More
Step 5: Select (1) USB to PC
Changing the type of USB connection your device uses can help with problems
connecting ActiveSync.
Step 6: Disable the option - Enable advanced network functionality
Step 7: Press done 3 times
Step 8: Return to main screen.
Step 9: Uninstall unrecognized USB device in device manager (on PC)
Step 10: reboot Phone and reconnect
Click to expand...
Click to collapse
If XP, keep going...
You've stated that the PC is recognising your other devices. Isn't there a limit to the number of windows mobile devices you can sync or associate with one installation of activesync? Can you delete a device and try again?
Is USB charging enabled or disabled in your phone? Try toggling the setting to opposite whatever it is.
If you are using a firewall app, add these programs to your firewall's exemptions:
# Wcesmgr.exe
# Wcescomm.exe
# Rapimgr.exe
Or simply disable any firewalls, network traffic optimisers or possibly antivirus (some have network protections) app to test if that has an effect.
Ok guys..
I will try doing all these, step by step and lets see
And accept my sincere gratitude from my heart for detailing all these info for me, I am soo deeply moved
Sincerely
Steve
ccpraveen said:
Ok guys..
I will try doing all these, step by step and lets see
And accept my sincere gratitude from my heart for detailing all these info for me, I am soo deeply moved
Sincerely
Steve
Click to expand...
Click to collapse
No need for thanx. If I helped, just give Nitro a donation on my behalf.
Well guys, with deep regret, I must say, even after trying all that, the phone stays put. PC wont recognise it, neither as a phone nor as a mass storage device. The connector port must have gone kaput.
I kinda feel stupid, u know, with all the tweaks and hacks out there, what use it is, if the dumb thing wont be recognised? Hmm.. So much for the tornado, now stuck at VJ 3.3 (unless someone find a way to flash via an SD image or something).
Well, thanks guys, your support did make me feel better, in the WM world, all is not lost, as long as there are good souls like you, willing to help, live and let live.
Regards
Steve.
PS: If the phone was not recognised in the bootloader mode, (ie even before the operating system has kicked in), I guess there should not be any difference if activesync was installed or not; and if or not mass storage option is enabled or not, right? Well, correct me if I am wrong, I think so. Could be wrong.
This is probably a useless comment, but have you tried using bluetooth instead of usb to connect to your computer?
Have u tried to delete the network card from XP device manager ?
U can also disable advanced network functionnality from your smartphone in "settings" -> "connections" -> "USB to PC"
Good luck
Can You Tried Different Usb Cable :d
i have some problem, after flashing to WM6 activesync or WM5torage can't connect..i have HTC prophet too, and i use same usb cable & PC, my HTC Prophet still can connect via activesync or WM5torage
*please..please..help us
I UPGRADEd vjgace Build_5.2.1616.18120_____v3.7 three days before today i can't connect to usb i tried diffrent app(activesync,wm5storage,internetsharing) but i can't connect so i go to bootloder mode and checked devicemanager i found device so i flashed nitrogenius rom and now working usb. try upgrade other ROM ON BOOTLODER MODE.
Cheers at all...
I have a HTC p4350. In most of cases, it's a very good smartphone, but I have the official HTC firmware to WM6 and I have lot of issues. The more frustating issue is the Internet Connection Sharing. My device WON'T WORK WELL sharing the internet to my pc's. Even when I try to share the internet I have problems: disconnections, slow navigation, etc.
Now I'll try to upgrade the firmware using the PDAVIET firmware in this site, but I have a great problem: I LOOSE the Original USB cable that connect my PDA to PC and any another cable that I try to use to connect, the system hangs a error "USB Device not recognized".
The ActiveSync works via bluetooth.
My question is: it's possible upgrade the PDA's firmware using the Bluetooth connection via ActiveSync or not? If it's possible, how I can do it?
Sorry my poor english and thanks for any help.
Challado said:
Cheers at all...
I have a HTC p4350. In most of cases, it's a very good smartphone, but I have the official HTC firmware to WM6 and I have lot of issues. The more frustating issue is the Internet Connection Sharing. My device WON'T WORK WELL sharing the internet to my pc's. Even when I try to share the internet I have problems: disconnections, slow navigation, etc.
Now I'll try to upgrade the firmware using the PDAVIET firmware in this site, but I have a great problem: I LOOSE the Original USB cable that connect my PDA to PC and any another cable that I try to use to connect, the system hangs a error "USB Device not recognized".
The ActiveSync works via bluetooth.
My question is: it's possible upgrade the PDA's firmware using the Bluetooth connection via ActiveSync or not? If it's possible, how I can do it?
Sorry my poor english and thanks for any help.
Click to expand...
Click to collapse
i think you'd better look for another cable
or try one of ivan's rom's that'll allow you to flash via sd card.
thanks
Yow I find a tutorial to make the upgrade via sd card dude?
Thanks for your answer!
You have to have a phone with HardSPL on it before you can flash through SD.
You'll need a cable. Most digital cameras, most... well... everything portable USB uses the same cable.
Most usb cables are capable of connecting a phone or external hd. The thin ones don't have the transfer rate needed to support powering a device and transferring data. Try looking for a thick usb like the one that comes with the ps3 to charge and sync the controllers.
Really, I try to insert another cables into the phone and pc. No one has worked.
The pin layout to the most of cables is (ascii art) \_/ and my P4350 have the |_/ layout. No one tested cable has worked, and all the cables, connected in another devices works perfectly (including the switch between cables and devices).
Cheers at all. I'll try with HardSPL
It will work fine if inserted the correct way. The |_/ connector is the same as the \_/ connector but with some extra pins added for audio, but trust me, any mini-b (\_/) connector works with it.
Oh, no way, Ivan.
"USB device not recognized". I believe that the mini-usb on cellphone is the problem, not the cable.
Well... Now I search on forum to find the steps to use the flashcard to upgrade firmware. I need much luck to these!
Thanks a lot for all help!
The mini-usb is broken? That sucks majorly...
As far as flashing from an SD card, it would only work if you have your phone already HardSPL. Just rename the file HERAIMG.nbh.
The mini-usb is broken? That sucks majorly...
As far as flashing from an SD card, it would only work if you have your phone already HardSPL. Just rename the file HERAIMG.nbh.
Oh, no way, Ivan.
"USB device not recognized". I believe that the mini-usb on cellphone is the problem, not the cable.
Well... Now I search on forum to find the steps to use the flashcard to upgrade firmware. I need much luck to these!
Thanks a lot for all help!
Oh, no way, Ivan.
"USB device not recognized". I believe that the mini-usb on cellphone is the problem, not the cable.
Well... Now I search on forum to find the steps to use the flashcard to upgrade firmware. I need much luck to these!
Thanks a lot for all help!
I just gave them to you.
Your phone has to be hardspl unless you only want to use official ROMs only. Just name the nbh to HERAIMG.nbh and then place it in the root directory of your SD card. Hold your camera button and press the soft reset. Then follow the instructions on the screen.
uhhh!!!
So much posts!!!
Arrgghhh! What's happen?
Ok, I'll try to do these Ivan.
How Image I can download to make these type of upgrade?
My mini-USB port is also broken on my TMO Wing. Same thing "USB Not Recognized" error when connected with any cable. Luckily whatever pin broke did not affect the power or I would not be able to charge.
Back on topic, Challado, your first post makes it sound like you have only the official ROMs now, and you want to flash to the custom ROM "PDAVIET firmware". Listen to Ivan on this, you can't flash via the SD Card to a custom ROM unless you have done a process called "Hard SPL" to your phone, which unfortunately DOES need the cable.
My USB port broke after I already performed the HARD SPL, so I have reflashed many times via SD Card since.
So, bottom line.... You cant reflash over BlueTooth, and without HARD SPL, you cant flash the firmware with an SD Card, the only alternative without an USB cable.
Did you try re-installing ActiveSync? Even if the bluetooth option for flashing did work, it will take a very long time for the process to finish. If you ever transfers files via bluetooth to your phone, you will notice the major speed difference and time factor against a usb cable. The fastest way to flash is via SD card. You are better off HardSPL your device like Ivan recommended. This method is reversible. What I don't get is how do you charge your phone if your mini-usb is broken?