Related
Ok I was flashing back to stock 2.1 useind odin when mid process my phone fell battery out usb disconnected and bam thats it. Now my phone is locked on a screen that shows a picture of a phone ! and a computer. I can get it back to download mode and odin will se the phone but gets no further then do not unplug device, my computer beeps when its plugged in but it dose not show the phone in my computer section. Any fixes or am i screwed?
PS phone is only two weeks old if need be could I take it back like this????
Hmm I think I may hove gotten past this problem. Uninstalled odin reinstalled and now it seems to be hopefully working
Here is the fix
I was in this same situation yesterday. Here is how to get it back into download mode.
•Be sure the Samsung USB drivers for the phone are installed on your computer.
•Remove and replace the battery.
•Connect the phone to the computer with the USB cable. The "phone-exclamation mark-computer" picture should display on the phone's screen.
•Hold the Volume Up+Volume Down+Power buttons down simultaneously.The screen should go blank, then the picture should appear again. When the screen goes blank a second time, release the Power button while continuing to hold the Volume Up+Volume Down buttons down
If that doesn't work,i had a similar problem where I could get into odin, but it would progress beyond the pit file. Take the battery, sim and memory card out of your phone. Start odin. Put the battery only back in. hold volume up and down. Plug the phone in while holding these buttons. Don't let go until you are in download mode. Now try restoring. It should work.
Thanks for the input i am back up and running!!
Sent from my SAMSUNG-SGH-I897 using XDA App
Bricked replacement Captivate - Orange Screen
Just to let you know. I recently received a replacement captivate thru warranty exchange. The phone was apparently a new one with JF6. So I decided to do an update to JH7 using Kies mini. A little over half way to the update procedure, the phone screen turned orange and stayed there for a long time, eventually I had to pull the plug. Of course I had to manually go to download mode and launch Kies mini emergency recovery, the damn thing again got stuck at the orange screen.
If anybody has this experience do no proceed further and throw that damn thing back at At&T's face. Do not attempt to do anything. I made a mistake of then doing an ODIN one-click back to stop and the phone got stuck half way, went to the orange screen.. and then it was over.. The phone was dead, wouldn't turn on, no recovery or download mode with any button combo. When I plugged in to the wall, no battery indicator.
save yourself the trouble and return the damn thing
still there
I am a "noob" to posting here, and a noob to the android due to being an avid iPhone user. I am having the same problem, phone -!- computer and have tried every method i can find in this forum to get passed it. Are there any other thoughts or suggestions? (got hung at do not turn off target in odin) Thanks in advance to any help.
I would look at this thread http://forum.xda-developers.com/showthread.php?t=1153310
Stephenv1971 said:
I would look at this thread http://forum.xda-developers.com/showthread.php?t=1153310
Click to expand...
Click to collapse
went that route, still cant find dl mode. have resistors built and all. any way i try to boot shows me the phone -!- computer, and the computer doesnt attempt to recognise it so there is no communication between the computer and phone. unfortunately, i dont have a v/ohm meter, so i am not sure of the accuracy of the resistors i used to make my jig.
I fixed this many times with phone that had the button download mode and didn't.
Getting into download mode while softbricked like this wont show the normal download screen. IT will still show the error screen....
With download mode working still:
Simply remove the battery and replace,
Open odin
Hold down volume keys and plug it in till you see odin recognize ur phone.
Then continue to use odin.
Dosent work, repeat.
If you know ur button combo dosent work:
Just open odin.
Remove battery & replace.
Use jig (3k 100k ohms twisted)
Then when the phone turns on and your see the pc! screen plug in usb.
See if odin sees it.
Assuming your flash didn't fail on the PBL.bin or SBL.bin you should be fine.
Follow the methods suggested by other users here and you will get back up and running in no time at all.
Don't sweat the 'phone-!-pc' screen. I'm a little surprised that no one has given you the good news....that is just a version of the download screen for later hardware revisions. It looks bad, but if Odin recognizes your phone (if one of the COM fields goes active), just start your flash again.
Now if Odin does not recognize the phone when plugged in via USB, then you have some more work to do.
I had forgotten about posting here, and my problem has been resolved. So here it is... I tried everything that I could find within this forum, almost. I built my own jig with inferior radio shack components that would not activate download mode, though it would turn the phone on. I got wise, spent 8 dollars at ebay and purchased a JIG there. Instant download mode after 3 days (shipping). Reflashed with one click, updated w/ kies, made kernal changes and am now rockin my captivate. Thanks to those who assisted.
Steve_O_1971 said:
I had forgotten about posting here, and my problem has been resolved. So here it is... I tried everything that I could find within this forum, almost. I built my own jig with inferior radio shack components that would not activate download mode, though it would turn the phone on. I got wise, spent 8 dollars at ebay and purchased a JIG there. Instant download mode after 3 days (shipping). Reflashed with one click, updated w/ kies, made kernal changes and am now rockin my captivate. Thanks to those who assisted.
Click to expand...
Click to collapse
Using the 3-resistor method takes A LOT of patience, at least in my experience. Glad everything worked out.
beast534 said:
Using the 3-resistor method takes A LOT of patience, at least in my experience. Glad everything worked out.
Click to expand...
Click to collapse
Patience is a virtue, and my Ex's name. LOL! I can do without patience.
Jokes aside, i actually soldered the resistors to a plug that i had cut up, and made sure it was covered so my skin wouldnt come in contact. The Radio Shack here buys inferior products and sells them at reggular retail. Unfortunately my $300.00 V-Ohm meter is on the fritz, and i have not had the time or money to replace it yet, but I have intentions to check the actual resistance of the jig I made. ^^
Okay, so i had Infused 2.3.0 (i think that was the number, it's the latest one anyway). I followed the instructions to the T. I had no issues.
About 3 or 4 days later i woke up and my phone had 1% battery. I sent a text, and then locked the phone. I came back to plug it in, and tried to see if it had any battery. None, it was dead. No biggie. I plug it in, and i get the circle loading thing. Then the battery symbol appears (charging). Then the phone goes black and the circle loading thing appears again. Then it keeps restarting. and going back to the circle loading thing. Over... and Over... Then i tried charging it for a while to see if the battery was just really low. No dice.
I put my girlfriends battery from her infuse 4g and it had 90%. Did the same thing. Circle loading thing, restart, circle loading thing, etc. Then i tried to put it into recovery. No dice, it would just keep restarting. Sometimes the Samsung logo would appear, and then it would just restart samsung, black screen, samsung, black screen, then eventually back to the circle.
I got it in red recovery ONCE, i was able to scroll down twice, and then the phone restarted. I couldn't get it back into red recovery.
I thought i had bricked my phone somehow. So i tried to use GTGs unbrick. I loaded it up fine (i'd done it with my girlfriends phone before to restore it to stock). It took me about 15 tries to get it into download mode. It was in download mode for long enough so that the program recognized it, and it started the download to restore it, then the phone turned off.
Now the phone won't even turn on. I can't put it in download mode, i can't put it into recovery, i can't get it to do ANYTHING.
What the hell did i do? What caused the original issue?
HELP
Does your phone still have warranty?
What the hell didn't you do.
Ok well first of all it is not Infused 2.3 it is 2.2.3. Anyway that is not the point, did you have juice defender installed? I do not think it could have done anything, but maybe. What is the latest app/tweak/anything you installed? Finally, have you tried holding both volume buttons and power button when trying to turn it on? This problem you are having seems extremely odd. Try plugging it in.
eatjello said:
Okay, so i had Infused 2.3.0 (i think that was the number, it's the latest one anyway). I followed the instructions to the T. I had no issues.
About 3 or 4 days later i woke up and my phone had 1% battery. I sent a text, and then locked the phone. I came back to plug it in, and tried to see if it had any battery. None, it was dead. No biggie. I plug it in, and i get the circle loading thing. Then the battery symbol appears (charging). Then the phone goes black and the circle loading thing appears again. Then it keeps restarting. and going back to the circle loading thing. Over... and Over... Then i tried charging it for a while to see if the battery was just really low. No dice.
I put my girlfriends battery from her infuse 4g and it had 90%. Did the same thing. Circle loading thing, restart, circle loading thing, etc. Then i tried to put it into recovery. No dice, it would just keep restarting. Sometimes the Samsung logo would appear, and then it would just restart samsung, black screen, samsung, black screen, then eventually back to the circle.
I got it in red recovery ONCE, i was able to scroll down twice, and then the phone restarted. I couldn't get it back into red recovery.
I thought i had bricked my phone somehow. So i tried to use GTGs unbrick. I loaded it up fine (i'd done it with my girlfriends phone before to restore it to stock). It took me about 15 tries to get it into download mode. It was in download mode for long enough so that the program recognized it, and it started the download to restore it, then the phone turned off.
Now the phone won't even turn on. I can't put it in download mode, i can't put it into recovery, i can't get it to do ANYTHING.
What the hell did i do? What caused the original issue?
HELP
Click to expand...
Click to collapse
Did you try your girlfriend's charged battery with the charger disconnected?
Sarius24 said:
Does your phone still have warranty?
Click to expand...
Click to collapse
Yeah I'm going to try to take it to the ATT store tomorrow to see what they say.
Eddie Bombay said:
What the hell didn't you do.
Click to expand...
Click to collapse
Thank you for the valuable contribution.
Ryanscool said:
Ok well first of all it is not Infused 2.3 it is 2.2.3. Anyway that is not the point, did you have juice defender installed? I do not think it could have done anything, but maybe. What is the latest app/tweak/anything you installed? Finally, have you tried holding both volume buttons and power button when trying to turn it on? This problem you are having seems extremely odd. Try plugging it in.
Click to expand...
Click to collapse
2.2.3, thanks. I was too lazy to look it up. No, I didn't have juice defender. I used Lookout, that's all.
The latest thing I installed was the 2.2.3 update for Infused. I updated Pandora, and that's all.
Yes, i've done that with the volume buttons.
Entropy512 said:
Did you try your girlfriend's charged battery with the charger disconnected?
Click to expand...
Click to collapse
Yes. Won't turn on.
Well, best thing you can do now is see what ATT can do about it. The worst that can happen is they say they can not do anything, which you then can keep trying the ultimate unbrick over again. This helped someone on an earlier thread.
Same thing happened to me. Take the battery out. Make sure USB cable is unplugged. Hold down both up and down volume buttons plug in USB into ur phone and PC and put battery back in. This will put you in download mode and it will stick do u can return to stock. Good luck
Sent from my SAMSUNG-SGH-I997 using XDA App
jmatt78 said:
Same thing happened to me. Take the battery out. Make sure USB cable is unplugged. Hold down both up and down volume buttons plug in USB into ur phone and PC and put battery back in. This will put you in download mode and it will stick do u can return to stock. Good luck
Sent from my SAMSUNG-SGH-I997 using XDA App
Click to expand...
Click to collapse
I'll try this again, but it didn't work last time. No matter what i did.
EDIT:
Tried again multiple times. It just won't turn on.
I think you have a hardware failure of some sort... Take it back to AT&T for warrany service.
You probably didn't do anything to it - just bad luck and coincidence.
Entropy512 said:
I think you have a hardware failure of some sort... Take it back to AT&T for warrany service.
You probably didn't do anything to it - just bad luck and coincidence.
Click to expand...
Click to collapse
this is exactly what i thought. and what i'm hoping. I'll let you guys know what happens tomorrow at ATT.
let me know what ATT says and how your approach was to them.
I just got my phonw into a boot loop ...
Was thinking if nothing works just play dumb with ATT.
Evanescense said:
let me know what ATT says and how your approach was to them.
I just got my phonw into a boot loop ...
Was thinking if nothing works just play dumb with ATT.
Click to expand...
Click to collapse
I'm at att right now waiting. Ill let you know what I say and what happens.
What rom were you using?
They're replacing it. No questions asked. The phone wont turn on. So they said its a hardware failure
The guy was really nice. Didn't ask me if I did anything to it
He tried everything I did. Download mode. New battery. Nadda
got my replacement today. all is well. now to root
I recently downloaded SD Maid Pro, cleaned out all the double files and now the Infuse just blinks Samsung until it dies. Can't get it to go into download mode or anything else. It just blinks Samsung til it dies. I plug in the charger and it just shows the starburst loading emblem. Can't turn it on, once I unplug the charger, it'll show Samsung and then just blink. Pulled the battery, put it back in.. automatically Samsung comes up and just blinks. Tried everything. I think it's done. Any suggestions?
-Rob
Can you tell me step by step how you are trying to get into download mode...maybe you might be doing something wrong...also even if the screen goes blank after doing steps for download mode try and see if Odin/heimdal recognize it
Sent from my HTC PH39100 using XDA
Odin won't recognize it. I pulled the battery. Put it back in. Before I can plug in the usb cable it's flashing the Samsung screen.
Ok, try this
1) Pull battery
2) hold volume up + down
3) plug USB into phone/pc with Odin or heimdal running
4) place battery in
See if it boots into download mode that way
Sent from my HTC PH39100 using XDA
Nope, Just shows the starburst loading icon blinking like before.
Hmmm...well, if your not too sketched out and you pay for shipping, ill take a look at it and try to fix it...this is just an option and I understand if you don't wanna do that option ad I am a stranger and these phones ate expensive...
Can you check the power button...make sure its not stuck down...helped a guy not too long ago who had a similar problem only to find out his power button was stuck down
Sent from my HTC PH39100 using XDA
BigRob1212 said:
Nope, Just shows the starburst loading icon blinking like before.
Click to expand...
Click to collapse
let is set for a few hours, may need to charge...
or buy a usb jig and see if that will force it into download mode... worked for me once.
como ysickp
I'm having the same issue here, but my phone hit nicely my bedside... it turns on, but keeps looping in the samsung screen
sorry for english
doggie3001 said:
I'm having the same issue here, but my phone hit nicely my bedside... it turns on, but keeps looping in the samsung screen
sorry for english
Click to expand...
Click to collapse
Have you attempted download mode? Could you also provide the steps you did to attempt download mode?
Sent from my HTC PH39100 using XDA
mg2195 said:
Have you attempted download mode? Could you also provide the steps you did to attempt download mode?
Sent from my HTC PH39100 using XDA
Click to expand...
Click to collapse
Yes, i've tried almost everything to get in download mode
download modes
nothing works it's like my power button is stuck, but it looks fine
M8, im dealing with the same situation with a couple motherboards. If im able to find a solution for that i will let you know. Ive done more than you have because i have even applied unbrickable mod to one of those two mobos with no luck. Pretty much same thing. The resurrector recognizes it but before it can resurrect the phone it will dissappear for good. So im starting to think it could be a damaged or corrupted file on the very lower levels of the infuse. But, at the same time, it maybe some hardware failure since i think unbrickable mod basically goes to the lowest level on the phone. Its a shame, but i have seen this many times on infuse phones. Never had to deal with that myself though....
Possible fix
My son brought me his phone last night with this same problem. I was not in the best mood to deal with it so made him, a teenager, go without a phone for a whole night....yeah dad of the year here. LOL. Anyway, I started working on it this morning and tried just about everyting I could think of until it thought of the Handyman's#! rule....If it doesnt work just bang on it. I took phone and with battery in it and cover on slapped it against my knee on the back cover in area where camera is. Dont try to break it just give it a good smack. Right after that it booted up and is just fine. LOL. I know it isnt the most scientific way to fix it...but it works for me and my son has his phone back. I hope this will help the rest of you out until we have a more defined solution.
Hello, I am trying to fix my friends phone and I cannot seem to get anything to work. Anytime I put in a battery the phone turns on to a white screen, nothing else. Sometimes the screen is pure white and sometimes it is kind of a slight pixelated colored look. Tried to use a jig and it is not working. The computer will detect the phone when plugged in but it will not recognize the device and shows as unknown device. I am not getting any logo screens or anything, nothing but the white screen. Any help is greatly appreciated, thanks.
Well knowing step use qkster one click hemidall n try to put phone in download mode I know blindly n all but try n if hemidall pick up phone u can set back hopefully
Sent from my SGH-I997 using xda premium
riotstarter said:
Hello, I am trying to fix my friends phone and I cannot seem to get anything to work. Anytime I put in a battery the phone turns on to a white screen, nothing else. Sometimes the screen is pure white and sometimes it is kind of a slight pixelated colored look. Tried to use a jig and it is not working. The computer will detect the phone when plugged in but it will not recognize the device and shows as unknown device. I am not getting any logo screens or anything, nothing but the white screen. Any help is greatly appreciated, thanks.
Click to expand...
Click to collapse
as stated...there is the one click or the odin.
ok install or reinstall drivers...and make sure the battery is charged, let it sit for a few hours to get some power back in it...
see my links for the Infuse Super Thread for all the tools you will need.
I have tried those methods. I cannot get the device to go into download mode, blindly or not. Also I have uninstalled and reinstalled the drivers many times and the device still always shows as unknown device no matter what. I have heard how hard it is to brick these things but damn, this one seems like it is, atleast beyond my abilities. He said what he was doing was updating the firmware and it froze. At first he said it showed the yellow triangle but he really didn't know what he was doing and once the battery died the screen would just flash white. Well he has since bought a stand alone battery charger and everything I have been trying does not work.
http://forum.xda-developers.com/showthread.php?t=1584583
http://forum.xda-developers.com/showthread.php?t=1496453
google: xda infuse white screen
qkster said:
http://forum.xda-developers.com/showthread.php?t=1584583
http://forum.xda-developers.com/showthread.php?t=1496453
google: xda infuse white screen
Click to expand...
Click to collapse
hey I remember that the first link...the white screen of no where...LOL
So I'm stumped... I've flashed my Charge many times, no problems until now.
I wanted to flash back to stock ROM and had my Samsung drivers installed and Odin recognizing the phone and everything was good, but then Odin was taking WAAAAAAY too long. In the past this usually took about 20 mins. This time, after 45 mins and the progress bar hanging in the same place for 30+ mins on factory.rfs I disconnected the phone (I know this is where I screwed up). Now Odin won't recognize the phone at all. It does get into download mode, but Odin won't pick it up.
Same computer, same cable, and same USB ports as I've had when flashing this phone many times before. I don't know what my options are now. I don't think I can flash either the ROM or PIT without Odin at least recognizing the phone. What can I do now?
So I've done some more tinkering - trying different cords, multiple computers, uninstall/reinstall different drivers... What I've noticed on more than one computer is that Odin doesn't recognize the phone when it's in download mode ONLY.
If I power on the phone Odin is able to detect it and windows detects it as a Samsung USB device (even though the phone hangs on the Samsung logo). When I put it into download mode both the computer and Odin don't recognize it.
dragonlady726 said:
So I've done some more tinkering - trying different cords, multiple computers, uninstall/reinstall different drivers... What I've noticed on more than one computer is that Odin doesn't recognize the phone when it's in download mode ONLY.
If I power on the phone Odin is able to detect it and windows detects it as a Samsung USB device (even though the phone hangs on the Samsung logo). When I put it into download mode both the computer and Odin don't recognize it.
Click to expand...
Click to collapse
FWIW, I've also noticed a simple computer reboot fixes it....
jco23 said:
FWIW, I've also noticed a simple computer reboot fixes it....
Click to expand...
Click to collapse
I neglected to mention in my OP that I was going through the right protocol with driver uninstall/reinstall and rebooting each time. I rebooted again for good measure after seeing your post but I still get the same.
It's the same result from two different computers, one with Win7 and the other XP (I read in another thread that XP had worked better for some). If the phone is powered on, even though it doesn't successfully boot, Odin and Windows recognize it properly. If it's in download mode neither one recognize it, windows says the device failed to start and shows either unrecognized device or "Gadget Serial" (which would be a great name for a band, but google searches for it aren't much help).
I don't think it's a driver problem because it's recognized when the phone is powered on. But could there be a specific driver out there for the phone when in download mode only? I've flashed this phone dozens of times and never had a problem until now. I'm on the verge of forking over the $50 and sending it to JTAG if no one can suggest something else to try. Please help
did you make sure your phone is in debugging mode?... i forget who flashed what... or where I read something about flashing and it turned off their debugging mode...so check that first...and try reinstalling Odin on your computer... i don't think jtag is necessary on a Droid charge... if your phone is being recognized then it seems your missing a step...like maybe pulling your battery before hooking up the usb... or reinstalling the battery after going in download mode... and last of all check and make sure your not accidentally making mistakes when setting up your Odin before flashing... and last efforts to get a working phone would be going into cwm... volume up... home... and power button... hold while powering up and releasing on the second Samsung logo...and install your last back up...or reflash your rom with cache and dalvik wipes
Sent from my SCH-I510 using xda premium
curious, when you are/were performing the Odin process, were you still using the computer (web-surfing, e-mail, etc.)? in my experience, whenever I tried to multi-task on my computer while running Odin on my phone, Odin freezes. this has happened on more than one occasion. also, my toddler daughter even pressed the power button while Odin was running - so on three separate occasions, I've had a reflash interrupted. however, I've clearly been able to recover.
the key was using the right cord in the right port. I had one cord working fine for awhile, but then when I switched cords, it worked again.
also, some folks have had better success when removing the battery during the process.
finally, what are your steps exactly when flashing - and which guide are you using?
lukegman said:
did you make sure your phone is in debugging mode?... i forget who flashed what... or where I read something about flashing and it turned off their debugging mode...so check that first...and try reinstalling Odin on your computer... i don't think jtag is necessary on a Droid charge... if your phone is being recognized then it seems your missing a step...like maybe pulling your battery before hooking up the usb... or reinstalling the battery after going in download mode... and last of all check and make sure your not accidentally making mistakes when setting up your Odin before flashing... and last efforts to get a working phone would be going into cwm... volume up... home... and power button... hold while powering up and releasing on the second Samsung logo...and install your last back up...or reflash your rom with cache and dalvik wipes
Sent from my SCH-I510 using xda premium
Click to expand...
Click to collapse
I can't actually get the phone to boot (doesn't get past Samsung logo) so I don't know how I can tell if it's in debugging mode or how to change it if it's not.
Going in to download mode I've tried both battery in and out, using multiple USB ports and cables and can't get any version of Odin to detect it. I've tried v1.82 and 1.85 of Odin. I get the same result for both - Odin does not detect the phone when in download mode, but will detect it if it's powered on or just connected to the computer with battery in to "charge." But afaik I can't flash it when it's NOT in download mode
It won't boot into into recovery either... It never gets past Samsung logo no matter how long I hold the buttons... I've used recovery before, so I'm sure I'm giving the android 3-finger salute correctly.
I'm thinking maybe I got unlucky because the whole key to flashing is having Odin recognize the phone in download mode and that's the only time that Odin won't recognize it.
jco23 said:
curious, when you are/were performing the Odin process, were you still using the computer (web-surfing, e-mail, etc.)? in my experience, whenever I tried to multi-task on my computer while running Odin on my phone, Odin freezes. this has happened on more than one occasion. also, my toddler daughter even pressed the power button while Odin was running - so on three separate occasions, I've had a reflash interrupted. however, I've clearly been able to recover.
the key was using the right cord in the right port. I had one cord working fine for awhile, but then when I switched cords, it worked again.
also, some folks have had better success when removing the battery during the process.
finally, what are your steps exactly when flashing - and which guide are you using?
Click to expand...
Click to collapse
I wasn't actively multitasking during the bad flash, although I may have had email running in the background. Since then I've been rebooting and only had Odin running in the foreground when trying. I did use multiple usb ports/cables and try going into download with battery in/out.
As far as guides go, I had been using trparky's awesome guide for years until he took it down and lately went to the one in the dev forum here on xda: http://forum.xda-developers.com/showthread.php?t=1160580
Like I said, I'm thinking maybe I got unlucky because Odin recognizes the phone when plugged into the computer EXCEPT when it's in download mode and without that I don't know what else to do.
dragonlady726 said:
I can't actually get the phone to boot (doesn't get past Samsung logo) so I don't know how I can tell if it's in debugging mode or how to change it if it's not.
Going in to download mode I've tried both battery in and out, using multiple USB ports and cables and can't get any version of Odin to detect it. I've tried v1.82 and 1.85 of Odin. I get the same result for both - Odin does not detect the phone when in download mode, but will detect it if it's powered on or just connected to the computer with battery in to "charge." But afaik I can't flash it when it's NOT in download mode
It won't boot into into recovery either... It never gets past Samsung logo no matter how long I hold the buttons... I've used recovery before, so I'm sure I'm giving the android 3-finger salute correctly.
I'm thinking maybe I got unlucky because the whole key to flashing is having Odin recognize the phone in download mode and that's the only time that Odin won't recognize it.
I wasn't actively multitasking during the bad flash, although I may have had email running in the background. Since then I've been rebooting and only had Odin running in the foreground when trying. I did use multiple usb ports/cables and try going into download with battery in/out.
As far as guides go, I had been using trparky's awesome guide for years until he took it down and lately went to the one in the dev forum here on xda: http://forum.xda-developers.com/showthread.php?t=1160580
Like I said, I'm thinking maybe I got unlucky because Odin recognizes the phone when plugged into the computer EXCEPT when it's in download mode and without that I don't know what else to do.
Click to expand...
Click to collapse
Also, are you sure you have enough battery juice? To make sure, leave it plugged in to a wall outlet for about 30 min to an hour.
tappin' that....
Finally fixed - Bad USB port
Just to close out the thread, I did finally get my phone fixed. The issue was a bad USB port that decided to fail during flash. This is according to Josh from MobileTechVideos, who is a great guy with amazing customer service.
Longer version: I sent it off to MobileTechVideos/JTAG and after a week I got a call back saying the JTAG process didn't work and as a last resort they could try replacing the USB port itself. Josh told me that it was either the port or the controller, that the port was a known failure point on the Charge, and if replacing the port didn't work it meant the USB controller had failed and I'd be out of luck. He also said that if the port replacement didn't fix the issue he wouldn't charge me and refund my original payment (which impressed the hell out of me given the time he had already put into it and there was no guarantee that the extra work would fix it). This was late afternoon on Valentine's Day... he said that he'd get to swapping out the port the next day but an hour later called back to tell me that he replaced the port and flash was successful. I wish everyone was as straightforward in communication and dedicated to their job.
So yeah, MobileTechVideos is legit, Josh is a rock star, and send those guys your phone if something really screwy happens. They will take the time and go above and beyond if necessary to fix it, and you will absolutely get your money's worth.
Hoping that no one else is "lucky" enough to have their USB port fail mid-flash, but if your symptoms look like mine a bad port might be your problem.
I've heard nothing but good things about them. I've never used them myself, but I have directed a couple of people to them and heard nothing but glowing reviews.
Cool I managed to finally back up my sd card after a few attempts with a bad port (went out after a month of having the phone). I've been on a rotating batteries off a wall charger system, but need to odin because everytime I get down to 110-120 ish mb of internal memory my charge says low memory blah blah, I clear cache, play store , etc.
Needless to say people have said resorting back to stock ep4 etc with Odin should work, but I'm afraid mid flash something will happen. I have to jam the cord in, wrap extremenly tight while holding the phone at a perfect angle and sometimes it still will beep like being disconnected.
I have no idea if this would be possible for you, but I wonder if Mobile Odin could help you?