Database Info

new chinese official rom Blur_Version.1.11.0.ME525.ChinaRetail.en.CN

Blur_Version.1.11.0.ME525.ChinaRetail.en.CN
ME525-JDGC_U6_1.11.0_SIGNED_USAJRDNPRCB1B50AA02F.0R_JORDANGCCORE_P011_A030_HWp3_Service1FF
http://u.115.com/file/f24b620be5
password "bbs.dkdiy.net" without quotes.
original source bbs.dkdiy.net
and http://bbs.goapk.com/thread-952839-1-1.html
lower bl version than UK, OR 2.2 sbf.....
not confirmed, but it may damage mb525's flash light... proceed with care.
for mb525, you might wanna use the nandroid backup with boot_only sbf to try it... both can be found in this thread
update with sources in this thread...
nandroid: http://u.115.com/file/t1fd48f976
thanks to SteveChou "here it's my system backup base on 1.11.0（new CN 2.2）, if anyone need it
Last edited by SteveChou; 25th February 2011 at 03:38 AM."
boot_only+devtree: http://forum.xda-developers.com/attachment.php?attachmentid=528823&d=1298827699
thanks to ollienightly

let's wait for someone whose camera flash is already dead to experiment with this one.
Sent from my MB525 using Tapatalk

ME525? Will this rom kill the flashlight?

the reason why the flashlight didn't work is mostly because the dev tree was not flashed properly. it's not the rom that kills the flashlight...
i didn't flash, so i couldn't be sure though
shady_lanem said:
ME525? Will this rom kill the flashlight?
Click to expand...
Click to collapse

does it include full screen recorder and 720p playback?

I am up for it, where should I download it?
don't tell me I have to install bunch of trogen before I can download.

i think that's an encrypted link and password is required.
to provide more information about this one:
i created a system.img out of cg39.smg, flashed it and that's it. you dont need a devtree or boot if you are already on 3.4.x
everything works properly, including flash which did not work with 0.26.0

racca said:
i think that's an encrypted link and password is required.
to provide more information about this one:
i created a system.img out of cg39.smg, flashed it and that's it. you dont need a devtree or boot if you are already on 3.4.x
everything works properly, including flash which did not work with 0.26.0
Click to expand...
Click to collapse
can you tell me how to flash it, or give me the img file.

http://u.115.com/file/t355594b48
here is the link without extract code

hello738 said:
can you tell me how to flash it, or give me the img file.
Click to expand...
Click to collapse
removed since there's a proper nandroid a few lines down
and also, i think a zip version should work on all 3.4.x

Mybe this is the original link?
http://bbs.gfan.com/android-736967-1-1.html
The guy says:
Still VGA, no 720p recording.
Photo qaulity improved a lot.
Compass still difficult to calibrate.
............

http://bbs.gfan.com/android-739900-1-1.html
The last two lines:
Based on testers' feedback, do NOT flash this sbf if you have flashed UK2.2, T2.2, or Orange2.2 sbf before or your defy will get bricked!
However, you can unbrick it by flashing your original system back.

Jasper.tw said:
http://bbs.gfan.com/android-739900-1-1.html
The last two lines:
Based on testers' feedback, do NOT flash this sbf if you have flashed UK2.2, T2.2, or Orange2.2 sbf before or your defy will get bricked!
However, you can unbrick it by flashing your original system back.
Click to expand...
Click to collapse
So most people here will be unable to use it unless a nandroid backup and a boot only is made.

http://u.115.com/file/t1fd48f976
here it's my system backup base on 1.11.0（new CN 2.2）, if anyone need it

Updated to new CN 2.21- 1.11.
( from official T-mobile 2.1 to official CN 2.21-0.26 )
This is what I did...
1. wipe
2. reboot to bootloader
3. flash new sbf via 4.9 (OMAP 3630)
4. wipe again
5. install google-market package (tks to sorensiim : http://www.mediafire.com/?4tgq4cmmzm4dc5v )
6. wipe again
7. root
8. install recovery
9. install t-mobile radio via recovery ( tks to adlx.xda: http://www.mediafire.com/?a0aaezdhazl3557 )
10. wipe again.
11. skip Blur setting.
Went straight to camera, greenish flash still exist. ( but it is working, nevertheless ) Video recording still on VGA only.
Other than that, I havn't play with it long enough.....
( since it is official 2.21, I will stay with it )
***** If you guys want me to check on something, let me know. ( will run quadrant later )

no clue said:
Updated to new CN 2.21- 1.11.
( from official T-mobile 2.1 to official CN 2.21-0.26 )
This is what I did...
1. wipe
2. reboot to bootloader
3. flash new sbf via 4.9 (OMAP 3630)
4. wipe again
5. install google-market package (tks to sorensiim : http://www.mediafire.com/?4tgq4cmmzm4dc5v )
6. wipe again
7. root
8. install recovery
9. install t-mobile radio via recovery ( tks to adlx.xda: http://www.mediafire.com/?a0aaezdhazl3557 )
10. wipe again.
11. skip Blur setting.
Went straight to camera, greenish flash still exist. ( but it is working, nevertheless ) Video recording still on VGA only.
Other than that, I havn't play with it long enough.....
( since it is official 2.21, I will stay with it )
***** If you guys want me to check on something, let me know. ( will run quadrant later )
Click to expand...
Click to collapse
Your Defy is MB525 or ME525?
I have the problem of Flash does not work (or burnt) and I have some hope that the resurrected ROM
I can flash the ROM if I have Froyo Orange (PL)?
Sorry for my English.
THX.

Can anyone tell me the difference between MB525 and ME525?

AgentSmith said:
Can anyone tell me the difference between MB525 and ME525?
Click to expand...
Click to collapse
ME525 is the Chinese version. IIRC, come with 850/1900 3G radio.

Darkcaptain said:
Your Defy is MB525 or ME525?
I have the problem of Flash does not work (or burnt) and I have some hope that the resurrected ROM
I can flash the ROM if I have Froyo Orange (PL)?
Sorry for my English.
THX.
Click to expand...
Click to collapse
I am Originally from the U.S. T-mobile MB525.
There is a warning, you can't flash this from higher 2.3+, such as UK/Tmobile Froyo.

any changelog?

[Q] Want to Flash Back to Stock: SBF Question

It seems that Motorola is very close to releasing GB for our D2G's, so I want to flash back to stock to be part of the soak/launch. When I originally rooted this phone, I saved all the files needed to root/unroot/flashback, but just want to confirm that DROID2WE_X6_2.4.29_FULL.sbf is the correct file. I have seen some 2.4.3 versions, but I think I have the right file.
Can anyone confirm, please?
Thanks!

Once you restore 2.4.29 you must OTA update it to 2.4.330 for the soak test.

...or download the 2.4.330 OTA .zip file and install it via stock recovery.

Gasai Yuno said:
...or download the 2.4.330 OTA .zip file and install it via stock recovery.
Click to expand...
Click to collapse
please give me that DL link. i can't find it..

Well, there you go. You'll need to rename it to “update.zip”, place it in your SD card's root directory, boot into the stock recovery and choose the option to install sdcard:update.zip.

There is also SBF available that can flash you up to the required 2.4.330 without having to apply the Dec 2010 OTA. Just one step less to do plus saves some time, if you haven't already done it.
Sent from my XT860 using Tapatalk

leobg said:
There is also SBF available that can flash you up to the required 2.4.330 without having to apply the Dec 2010 OTA. Just one step less to do plus saves some time, if you haven't already done it.
Sent from my XT860 using Tapatalk
Click to expand...
Click to collapse
Do you have a link for the .330 update SBF?

ancorare said:
Do you have a link for the .330 update SBF?
Click to expand...
Click to collapse
I have the file, I don't remember where I downloaded it, it was a while ago. I will try to upload it somewhere for you tonight.
Sent from my XT860 using Tapatalk

Nevermind, turns out I don't need it anymore. I hunted around a bit and found a thread over at droidforums.net that links to the official 2.4.330 SBF with RSDLite and Moto driver downloads, and a suuuper helpful tutorial. I followed each step and SBF'd to stock without a problem!
Here's the link, if the OP or anyone else wants it. (add http and whatnot, I can't post direct links yet)
droidforums.net/forum/droid-2-global-hacks/147264-official-2-4-330-d2g-sbf-tbh.html
P.S. sorry if this link (or another similar one) is already floating around. The more, the merrier, eh?

Gasai Yuno said:
Well, there you go. You'll need to rename it to “update.zip”, place it in your SD card's root directory, boot into the stock recovery and choose the option to install sdcard:update.zip.
Click to expand...
Click to collapse
if we update with this does it update the baseband also ?
I am trying to find a way to get gingerbread work with cellzeolot's hack...

As it has been stated quite a few times, both 2.4.330 and 4.5.x update the baseband firmware.
Band unlock won't work on those versions.
You cannot skip baseband update.

ancorare said:
Do you have a link for the .330 update SBF?
Click to expand...
Click to collapse
Found it: here is the post I downloaded it from: http://modmymobile.com/forums/649-m...re-vrz_a956_2-4-33_1ff_01-droid-2-golbal.html
edit: huh - just saw you found it already 'mirrors' won't hurt

[Q] Need Stock Rom 2.3.6 For Motorola Atrix 2 ME865 [SBF File]

hi
i need stock rom 2.3.6 for motorola atrix2 me865 [sbf file] for flashing with rsd
tnx

I don't believe we have a FXZ available yet to flash directly to 2.3.6.
Look at the guides on how to flash back to 2.3.5 from 2.3.6. You should then be able to update.
edit: the specific guides I was thinking of here are inapplicable to the ME865

my phone can't boot
i can not flash costum rom & zip file with CWM
i need a rom with sbf format (ME865) for flashing rsd
sorry i don't write english good

You can find certain ME865 FXZ files from the nice Chinese folks over at bbs.gfan.com, but I would make sure to only flash the fxz for your own region.
It may be the fxz file for your region is not available yet... I'm not sure where you are.
FXZ (fastboot-xml-zip) files are the newer equivalent of SBF.
If it's anything like the american MB865's updates, you might have to replace certain files in the fxz and update the XML file with the MD5 hash.
The replacement files would need to come from the update package itself.
(the zip file downloaded from Motorola's servers and stored in the /cache directory until the update finishes and it's promptly deleted forever...)

tnx
can i use this method?
http://forum.xda-developers.com/showthread.php?t=1539167

Unfortunately that's for the American MB865.
I've heard of some people flashing the ME865 with american roms, but I would not recommend flashing the full MB865 fxz to your ME865 as this method does.
---------- Post added at 11:43 PM ---------- Previous post was at 11:35 PM ----------
Forgot about mfunz...

i have a backup file from stock rom 2.3.6 . but i can't restore with CWM

That's good.
Depending on what's preventing it from booting up, you might be able to flash just the system image from another me865 fxz, then restore your stock system image once you're able to boot to kick off cwm.
This can be done through moto-fastboot, or with rsd lite- removing extraneous steps from the xml file to skip everything except /system
This all depends on how your phone is actually bricked...
Sometimes seemingly softbricked phones can still be booted with a "normal boot" from the VolumeUp+VolDown boot menu or alternatively BP Tools

can i flash CWM with fastboot or rsd ?
and then restore the backup ?

hayoola said:
i have a backup file from stock rom 2.3.6 . but i can't restore with CWM
Click to expand...
Click to collapse
How did you do that? :what:
Sent from my MB865 using xda premium

1.root with 1-click_exploit
2.install CWM with a2 bootstrap.apk
3. creat a backup from original rom
4.flash this rom http://forum.xda-developers.com/showthread.php?t=1420980
5.and then tested this rom restore the backup
6.now phone can not boot

moofree said:
You can find certain ME865 FXZ files from the nice Chinese folks over at bbs.gfan.com, but I would make sure to only flash the fxz for your own region.
It may be the fxz file for your region is not available yet... I'm not sure where you are.
FXZ (fastboot-xml-zip) files are the newer equivalent of SBF.
If it's anything like the american MB865's updates, you might have to replace certain files in the fxz and update the XML file with the MD5 hash.
The replacement files would need to come from the update package itself.
(the zip file downloaded from Motorola's servers and stored in the /cache directory until the update finishes and it's promptly deleted forever...)
Click to expand...
Click to collapse
What should I do EXACTLY?! Tnx a lot

hayoola said:
What should I do EXACTLY?! Tnx a lot
Click to expand...
Click to collapse
Not quite sure. It looks like you've already tried restoring the cwm backup, which caused the issue?
What exactly is your phone doing when you power it up?
To use moto-fastboot to flash only the system image, download an ME865 FXZ, put the system.img file from the fxz into the same directory you extracted moto-fastboot, then from that directory in a command line (with your phone booted into fastboot and connected via usb) run
Code:
moto-fastboot flash system system.img
This will restore only the system directory, leaving everything else alone.

[Q] help me: help my atrix 2 flash failure

I just use RSD 5.6 to flash my atrix 2 to 2.3.5 but flash failure .
it is notice that
"Failed flashing process. Failed flashing process. 1/19 flash mbm "allow-mbmloader-flashing-mbm.bin" -> USB error occured while reading/writing.; phone connected."
and then, when i go to FastBoot mode, it is notice that
"AP Fastboot Flash Mode (S) (Flash Failure)
0A.68
Baterry OK
OK to Program
Connect USB
Data Cable."
help me, thanks all

manbk401 said:
I just use RSD 5.6 to flash my atrix 2 to 2.3.5 but flash failure .
it is notice that
"Failed flashing process. Failed flashing process. 1/19 flash mbm "allow-mbmloader-flashing-mbm.bin" -> USB error occured while reading/writing.; phone connected."
and then, when i go to FastBoot mode, it is notice that
"AP Fastboot Flash Mode (S) (Flash Failure)
0A.68
Baterry OK
OK to Program
Connect USB
Data Cable."
help me, thanks all
Click to expand...
Click to collapse
We need more info to help you. which version of the phone? were you on 2.3.6 or 2.3.5 before the flash? do you have drivers installed correctly?

lkrasner said:
We need more info to help you. which version of the phone? were you on 2.3.6 or 2.3.5 before the flash? do you have drivers installed correctly?
Click to expand...
Click to collapse
the first, i use Retail Indian - 5.5.1-EDEM-28-37-SEARET rom (2.3.6). I want to up to Supercharged v5 (following that ). but when completed, my phone just stops at boot screen (i wait 10 minutes but not change).
after that, i go to FastBoot mode and flash to 2.3.5 via RSD Lite. the failure was happended
i use RSD lite 5.6 and Motorola 5.2 Drivers.
ps: I tryed Flashboot following this topic: 2.3.6 from modified 2.3.5 Flashboot: "Invalid CG Version" FIX but nothing change

manbk401 said:
the first, i use Retail Indian - 5.5.1-EDEM-28-37-SEARET rom (2.3.6). I want to up to Supercharged v5 (following that ). but when completed, my phone just stops at boot screen (i wait 10 minutes but not change).
after that, i go to FastBoot mode and flash to 2.3.5 via RSD Lite. the failure was happended
i use RSD lite 5.6 and Motorola 5.2 Drivers.
ps: I tryed Flashboot following this topic: 2.3.6 from modified 2.3.5 Flashboot: "Invalid CG Version" FIX but nothing change
Click to expand...
Click to collapse
go to the noob thread and follow the instructions for replacing files in the fxz, just use the same replace files but the indian fxz that you can download.

lkrasner said:
go to the noob thread and follow the instructions for replacing files in the fxz, just use the same replace files but the indian fxz that you can download.
Click to expand...
Click to collapse
sorry, i don't understand u. i don't have the indian fzx. i'm vietnamese. when i bought atrix 2 at&t, my phone is still on stock 2.3.6.

manbk401 said:
sorry, i don't understand u. i don't have the indian fzx. i'm vietnamese. when i bought atrix 2 at&t, my phone is still on stock 2.3.6.
Click to expand...
Click to collapse
No problem. Just go here: http://forum.xda-developers.com/showthread.php?t=1396650 and read the section on how to flash the FXZ. make sure to look at the bottom part where it tells you to replace some files. you will need to do that. Instead of using the ATT FXZ file like they say use the one that matches your current version (SEARET I think you said) and follow the same directions, but use that file instead. Get if from here: http://sbf.droid-developers.org/edison/list.php

lkrasner said:
No problem. Just go here: http://forum.xda-developers.com/showthread.php?t=1396650 and read the section on how to flash the FXZ. make sure to look at the bottom part where it tells you to replace some files. you will need to do that. Instead of using the ATT FXZ file like they say use the one that matches your current version (SEARET I think you said) and follow the same directions, but use that file instead. Get if from here: http://sbf.droid-developers.org/edison/list.php
Click to expand...
Click to collapse
ok, thanks u. i will try to do follow your help. in vietnam, it's 1 am, i need to sleep .
have a nice day

manbk401 said:
I just use RSD 5.6 to flash my atrix 2 to 2.3.5 but flash failure .
it is notice that
"Failed flashing process. Failed flashing process. 1/19 flash mbm "allow-mbmloader-flashing-mbm.bin" -> USB error occured while reading/writing.; phone connected."
and then, when i go to FastBoot mode, it is notice that
"AP Fastboot Flash Mode (S) (Flash Failure)
0A.68
Baterry OK
OK to Program
Connect USB
Data Cable."
help me, thanks all
Click to expand...
Click to collapse
This is right sbf or FXZ for SEART ROM
http://sbf.droid-developers.org/edison/5.5.1-EDEM-27-SEARET_cfc.xml.zip
Reinstall Drivers and RSD Lite and try flashing it, it should work

prasannapmv said:
This is right sbf or FXZ for SEART ROM
Reinstall Drivers and RSD Lite and try flashing it, it should work
Click to expand...
Click to collapse
can i should replace some file in above zip? because my phone is 2.3.6
Code:
How to flash the FXZ once applying the OTA update and get back to 2.3.5, ONCE YOU UPDATE TO THE OTS 2.3.6 YOU WILL NOT BE ABLE TO FLASH THE 2.3.5 FXZ WITHOUT FOLLOWING THESE STEPS BELOW!!
NOTE: Download this file HERE -
Unzip it and move all the the items in it to the stock fxz. You might get a warning about replacing files, just click OK. NOTE that Windows might not be able to handle the size of the fxz. I have 6 GB RAM but Windows still wasn't able to perform a drag-and-drop through the fxz's zip. I recommend that you just unzip the fxz and then put the files in. (You don't have to rezip it either, RSD Lite will still recognize it and will flash faster).
You should be able to use RSD Lite to flash the file.

lkrasner said:
No problem. Just go here: http://forum.xda-developers.com/showthread.php?t=1396650 and read the section on how to flash the FXZ. make sure to look at the bottom part where it tells you to replace some files. you will need to do that. Instead of using the ATT FXZ file like they say use the one that matches your current version (SEARET I think you said) and follow the same directions, but use that file instead.
Click to expand...
Click to collapse
i've downloaded the india FXZ and the replace file. but the xml file is not same name.
in replace file is InlineFlashing_edison_5.5.175.16_cfc_p3_APBP_CID285, and in india FZX is 5.5.1-EDEM-27-SEARET_cfc
and a question, my phone use code unlock AT&T, so if I flash to india FXZ, any problem happen with my atrix 2?

manbk401 said:
i've downloaded the india FXZ and the replace file. but the xml file is not same name.
in replace file is InlineFlashing_edison_5.5.175.16_cfc_p3_APBP_CID285, and in india FZX is 5.5.1-EDEM-27-SEARET_cfc
and a question, my phone use code unlock AT&T, so if I flash to india FXZ, any problem happen with my atrix 2?
Click to expand...
Click to collapse
Yeah, I was being stupid. Was the phone originally ATT when you bought it, or was it indian. that makes a big difference. you need to know what it said under settings > about phone.
anyways this should fix it, just use which ever fxz is right (from my post in the noob thread:
just thought of an easier way to get you restored. Most of the time you only really need to do system. download the moto-fastboot utility (it's similar to normal fastboot but you MUST use it instead or it will not work) and the fxz for your region. Extract the fxz and put the system.img from it and moto-fastboot in the same folder. open a command prompt in that folder (hold shift and right click) and type
Code:
moto-fastboot.exe flash system system.img
moto-fastboot.exe erase userdata
obviously you need to have your phone in fastboot mode to do that. it does the exact same thing as rsd, just only the 2 important steps, flashing system and wiping data.)
Let me know how that works for you. It may not since you have had flash failures, but we'll see.
moto-fastboot: http://forum.xda-developers.com/attachment.php?attachmentid=635584&d=1308928440 you should actually extract it and put all the things in it in the folder with system.img
Good luck!

lkrasner said:
Yeah, I was being stupid. Was the phone originally ATT when you bought it, or was it indian. that makes a big difference. you need to know what it said under settings > about phone.
anyways this should fix it, just use which ever fxz is right (from my post in the noob thread:
just thought of an easier way to get you restored. Most of the time you only really need to do system. download the moto-fastboot utility (it's similar to normal fastboot but you MUST use it instead or it will not work) and the fxz for your region. Extract the fxz and put the system.img from it and moto-fastboot in the same folder. open a command prompt in that folder (hold shift and right click) and type
Code:
moto-fastboot.exe flash system system.img
moto-fastboot.exe erase userdata
obviously you need to have your phone in fastboot mode to do that. it does the exact same thing as rsd, just only the 2 important steps, flashing system and wiping data.)
Let me know how that works for you. It may not since you have had flash failures, but we'll see.
moto-fastboot: http://forum.xda-developers.com/attachment.php?attachmentid=635584&d=1308928440 you should actually extract it and put all the things in it in the folder with system.img
Good luck!
Click to expand...
Click to collapse
hi, i'm a lucky man. i flashed my phone following Return to Stock 2.3.5 Fastboot SCRIPT. and now, my phone is ok
thanks 4 your help

manbk401 said:
hi, i'm a lucky man. i flashed my phone following Return to Stock 2.3.5 Fastboot SCRIPT. and now, my phone is ok
thanks 4 your help
Click to expand...
Click to collapse
yep, that works pretty well too. It does exactly what I said to do, but more. I do this because it goes faster

want to get back to 2.3.6
plz help me ma phone was on 2.3.6 then i tried to flash indian rom but it says flash error
n i tried several rom bt it didnt work ... all are the same
how can i get back to 2.3.7 ..thank you

i have this 5.5.1 EDEM 27 searet file which is 517 mb
should i flash this or download another 5.5.1 EDEM 28 27 searet WHICH IS 519 mb and will that hard brick my phone if i flash wrong file? im from india and recently purchased this phone and im on 2.3.6

hemanbond said:
i have this 5.5.1 EDEM 27 searet file which is 517 mb
should i flash this or download another 5.5.1 EDEM 28 27 searet WHICH IS 519 mb and will that hard brick my phone if i flash wrong file? im from india and recently purchased this phone and im on 2.3.6
Click to expand...
Click to collapse
Look in settings>about phone..then download accordingly..55.28.37 is the latest in gb 2.3.6..
Sent from my MB865 using xda app-developers app

ye i have 55.28.37 ...so which file should i download?
---------- Post added at 01:30 PM ---------- Previous post was at 01:27 PM ----------
5.5.1-EDEM-28-37-SEARET_cfc.xml.zip
is this the one which ill have to download? and is this 2.3.5 or 2.3.6 and do i need to replace the files in order to flash ...just asking cause im curious...i dont wanna hard brick

hemanbond said:
ye i have 55.28.37 ...so which file should i download?
---------- Post added at 01:30 PM ---------- Previous post was at 01:27 PM ----------
5.5.1-EDEM-28-37-SEARET_cfc.xml.zip
is this the one which ill have to download? and is this 2.3.5 or 2.3.6 and do i need to replace the files in order to flash ...just asking cause im curious...i dont wanna hard brick
Click to expand...
Click to collapse
Yup this is the zip u need..its 2.3.6..no replacing..just flash
Sent from my MB865 using xda app-developers app

Flashed my atrix 2 and fastboot fail
I bought my atrix 2 from US and unlocked it and am using this in india now. I tried to flashboot the phone with "5.5.1-EDEM-28-37-SEARET_cfc.xml". I added the new files thats available in the noob called replace.zip. I also tried the moto fast boot. Now am not able to flashboot and when i run flashboot i get this error "failed flashing process. 11/21 flash ebr "ebr"-> Phone returned fail; Phone connected" .
Please help me.

I just got my ATT Atrix 2 and I think I've already bricked it, soft at least. I used a script to go from 2.3.6 back to 2.3.5 stock, then OTA to 2.3.6, then I flashed the ICS leak and flashed SCV7, it was running horribly, kept crashing and was being extremely unstable so then I tried to use the FXZ script to go from ICS back to GB, and all my phone was doing was showing the Motorola dual core screen and boot looping or just staying on that screen I couldn't tell. I can get into fastboot, when I try to get into recovery there is an icon of a box with an arrow coming out of it and a little android and a yellow progress bar and when that finishes it goes to fastboot and it says "AP FastBoot Flash Mode (S) (Flash Failure) what can I do?
---------- Post added at 07:12 PM ---------- Previous post was at 06:55 PM ----------
The battery is low going by my luck I'm going to assume the phone will not charge while in fast boot. I've been at this for way too many hours, if someone could tell me how to get this phone working I'd appreciate it.

[Q] Upgrade to Jellybean

I'm rooted with the stock ROM, and my bootloader is unlocked using the Motorola website.
What's the easiest and effective way to upgrade to the newest (Jellybean) OTA update?

Also, I forgot I had rooted because I installed the OTA and tried to apply it but of course it failed.
Now when I start my phone up...it will load then a couple seconds later, it shuts down and boots into CWM.
What can I do?

Easiest way at this point is probably to use RSD Lite and wipe the phone with one of the FXZ's.
Then wait for the OTA and flash it.
You can't flash OTA's on aftermarket recoveries. You have to be on stock recovery to take the OTA......
Edit - link for reference.
http://forum.xda-developers.com/showthread.php?t=2095536&highlight=rsd+lite

arrrghhh said:
Easiest way at this point is probably to use RSD Lite and wipe the phone with one of the FXZ's.
Then wait for the OTA and flash it.
You can't flash OTA's on aftermarket recoveries. You have to be on stock recovery to take the OTA......
Edit - link for reference.
http://forum.xda-developers.com/showthread.php?t=2095536&highlight=rsd+lite
Click to expand...
Click to collapse
Is there any chance you could explain the RSD steps? I'm having the same problem, unlocked through Moto's site and now entering bootloop when I try to do OTA upgrade.

vertexoflife said:
Is there any chance you could explain the RSD steps? I'm having the same problem, unlocked through Moto's site and now entering bootloop when I try to do OTA upgrade.
Click to expand...
Click to collapse
Do you have RSD Lite? What step are you getting stuck on?
It's pretty straightforward IMHO. The only "wrinkle" is having to edit the .XML files - which is noted int he first post.

arrrghhh said:
Do you have RSD Lite? What step are you getting stuck on?
It's pretty straightforward IMHO. The only "wrinkle" is having to edit the .XML files - which is noted int he first post.
Click to expand...
Click to collapse
My apologies, shoulda been clearer. I am installing RSD onto my computer right now. Which asanti_c_cspire would you recommend?

vertexoflife said:
My apologies, shoulda been clearer. I am installing RSD onto my computer right now. Which asanti_c_cspire would you recommend?
Click to expand...
Click to collapse
Well I wouldn't recommend any cspire FXZ unless you're on cspire...
You're on Sprint right? I'd grab the latest Sprint FXZ, which is currently:
asanti_c-user-4.0.4-7.7.1Q-6_SPR-125_ASA-14-15-release-keys-Sprint-US.xml.zip
Hopefully the Sprint FXZ for JB will land, and people can just flash straight to it

arrrghhh said:
Well I wouldn't recommend any cspire FXZ unless you're on cspire...
You're on Sprint right? I'd grab the latest Sprint FXZ, which is currently:
asanti_c-user-4.0.4-7.7.1Q-6_SPR-125_ASA-14-15-release-keys-Sprint-US.xml.zip
Hopefully the Sprint FXZ for JB will land, and people can just flash straight to it
Click to expand...
Click to collapse
Thanks a bunch. I'm gonna go ahead and download that. It would make my life so much easier if the Sprint one was availble, but it's not so now gotta go back to stock.
When using RSD lite i just connect my phone as USB Mass storage, edit the XML file, and then load it into RSD and hit start?

vertexoflife said:
Thanks a bunch. I'm gonna go ahead and download that. It would make my life so much easier if the Sprint one was availble, but it's not so now gotta go back to stock.
When using RSD lite i just connect my phone as USB Mass storage, edit the XML file, and then load it into RSD and hit start?
Click to expand...
Click to collapse
Yea, RSD should reboot your phone into fastboot mode and start flashing.
If it doesn't, you might have to enable adb... I can't remember as I always have adb setup/enabled

arrrghhh said:
Yea, RSD should reboot your phone into fastboot mode and start flashing.
If it doesn't, you might have to enable adb... I can't remember as I always have adb setup/enabled
Click to expand...
Click to collapse
I apologize for having another question... Installed ADB, Motorola Device drivers, ran adb on cmd prompt, and started RDS Lite but the device is not showing on RSD lite. how do I get it to show?
Thanks again

vertexoflife said:
I apologize for having another question... Installed ADB, Motorola Device drivers, ran adb on cmd prompt, and started RDS Lite but the device is not showing on RSD lite. how do I get it to show?
Thanks again
Click to expand...
Click to collapse
don't start adb from a command prompt. RDS will take care of that. USB debugging must be enabled on your phone in developer options.
---------- Post added at 02:25 PM ---------- Previous post was at 02:19 PM ----------
can someone please post a stock jellybean rom for use with TWRP or a flashable zip for CWM? I have been trying for hours to get JB ota, and soft bricked along the way. I read everything on xda tried RSD Lite, and this http://forum.xda-developers.com/showthread.php?t=2001108 but still cant ota.

btsbits said:
don't start adb from a command prompt. RDS will take care of that. USB debugging must be enabled on your phone in developer options.
---------- Post added at 02:25 PM ---------- Previous post was at 02:19 PM ----------
can someone please post a stock jellybean rom for use with TWRP or a flashable zip for CWM? I have been trying for hours to get JB ota, and soft bricked along the way. I read everything on xda tried RSD Lite, and this http://forum.xda-developers.com/showthread.php?t=2001108 but still cant ota.
Click to expand...
Click to collapse
I have USB debugging enabled...but my phone wont show up in RDS. The only option I have is to decompress, no flash option, no phone showing up. ADB is not recognizing phone either..

btsbits said:
can someone please post a stock jellybean rom for use with TWRP or a flashable zip for CWM? I have been trying for hours to get JB ota, and soft bricked along the way. I read everything on xda tried RSD Lite, and this http://forum.xda-developers.com/showthread.php?t=2001108 but still cant ota.
Click to expand...
Click to collapse
Flash ASA-14 from the FXZ's, then force check for a system update.
Looks like the FXZ for Sprint's 4.1.2 is released. Just use RSD lite and flash straight to it.
Thanks Skrilax_CZ.
vertexoflife said:
I have USB debugging enabled...but my phone wont show up in RDS. The only option I have is to decompress, no flash option, no phone showing up. ADB is not recognizing phone either..
Click to expand...
Click to collapse
I think once you get ADB to recognize the phone, RSD will as well.

arrrghhh said:
Flash ASA-14 from the FXZ's, then force check for a system update.
Looks like the FXZ for Sprint's 4.1.2 is released. Just use RSD lite and flash straight to it.
Thanks Skrilax_CZ.
I think once you get ADB to recognize the phone, RSD will as well.
Click to expand...
Click to collapse
Got it. Trying OTA Update now. Thanks!

Great link skillrax.
RSD l ite is really easy. You need to have fastboot installed on the PC/phone and you need to enable debugging. Then its as easy as 3 steps. Find the file, choose flash. Forget the 3rd step.... Its really easy.

matt2k12 said:
Great link skillrax.
RSD l ite is really easy. You need to have fastboot installed on the PC/phone and you need to enable debugging. Then its as easy as 3 steps. Find the file, choose flash. Forget the 3rd step.... Its really easy.
Click to expand...
Click to collapse
Yea, I don't know what the heck I was thinking earlier... RSD uses fastboot, so you will need adb/fastboot working in order to utilize RSD.
Other than editing that XML file and getting fastboot working, RSD is quite simple to use

Hey y'all. I was going to go back to one of my early backups on the stock ICS and then take the OTA JB update but my backup from January keeps loading my most recent twisted asanti backup instead. Needless to say, my JB update keeps failing saying signature verification failed. Any quick fix or should I just push it via RSD at work tomorrow?
TIA

arrrghhh said:
Flash ASA-14 from the FXZ's, then force check for a system update.
Looks like the FXZ for Sprint's 4.1.2 is released. Just use RSD lite and flash straight to it.
Thanks Skrilax_CZ.
Click to expand...
Click to collapse
Thank you for alerting me to the new FXZ. It wasn't there when i checked yesterday. This new one did the job for me. I have backed it up using TWRP and I am uploading to my server for download, but I can't post external links yet.

Okay:
- I have /sdk-tools/ in my c:/ drive.
- I downloaded the Jellybean file
- I downloaded RSDlite and edited the xml file
My device doesnt show in RSD or anything.
Now what?

Wesley12 said:
Okay:
- I have /sdk-tools/ in my c:/ drive.
- I downloaded the Jellybean file
- I downloaded RSDlite and edited the xml file
My device doesnt show in RSD or anything.
Now what?
Click to expand...
Click to collapse
Sounds like you don't have the drivers. Go to motorola.com and make sure you have the latest / correct drivers. RSD is a moto program so with Moto drivers and RSD lite you should have no problem. You also need to have fastboot on both your phone and the computer.
Then you may need an xml editor to remove those files (I have to every time) and after that its really easy.
Open RSD Lite
Connect Phone
Select File
Decompress and Flash
RSD Instructions: http://wiki.howardforums.com/index.php/How_to_flash_with_RSD_lite