so i was trying to flash kg4 kernel with odin and it got stuck and my phone powered off. When try to enter recovery or download mode i get this message "firmware upgrade fail! try using recover". any help would be greatly appreciated thanks.
nav200 said:
any help would be greatly appreciated thanks.
Click to expand...
Click to collapse
Give us more info. What are you flashing from (FROYO or GB)? Why KG4 kernel? Are you trying to change your modem?
This.. charge your phone to full then try and enter dl mode if its not letting you in you may need a USB jig if your on a Samsung device. I'm only assuming because Odin usually uses Samsung stuff from my experience.. otherwise need a lot more info
lumin30 said:
Give us more info. What are you flashing from (FROYO or GB)? Why KG4 kernel? Are you trying to change your modem?
Click to expand...
Click to collapse
Sent from my SPH-D710 using XDA App
i was following the steps from this http://forum.xda-developers.com/showthread.php?t=1215748. I was on stock 2.2.1 and i was trying to flash cm hybrid gb. i was also using odin.
Will your ROM load?
i loaded the md5 on pda then i started it but it got stuck and my phone powered off, that's it.
So you have a galaxy s4g? Can you get into recovery with a full battery?
Sent from my SPH-D710 using XDA App
yup i have a gs4g but when i try to enter recovery the same message appears firmware upgrade fail
Will you ROM load?
nope it won't load
Even though you can't get into recovery... plug your phone in and see if ODIN recognizes it.
You should try starting ODIN again obviously with your phone plugged in. See what happens.
nav200 said:
i was following the steps from this http://forum.xda-developers.com/showthread.php?t=1215748. I was on stock 2.2.1 and i was trying to flash cm hybrid gb. i was also using odin.
Click to expand...
Click to collapse
If you are able to get Odin to recognize your phone, i would redo the whole thing again, maybe it was just a bad flash.
If it happens again, try re-downloading the kernel, and redoing it again.
What step were you on in the guide? IF you flashing the kernel should be step 11. Sounds like your phone ran out of battery. If you plug it into the wall charger does it charge?
i was in step 11 and my phone was 80% charged before i entered download mode. When I plug in charger the same screen pops up and odin doesn't recognize it now.
are you entering DL by the battery pull method? Odin should see it that way. I've had to try a lot of times in the past to get odin to recognize the phone but it always does.
yup the battery pull method, i've tried like 6 times but no luck
plug into a different usb port on the computer. close odin reopen it and try six more times.
nav200 said:
yup the battery pull method, i've tried like 6 times but no luck
Click to expand...
Click to collapse
Plug your phone in and restart ODIN. Try it. Make sure all your settings are correct.
wow it actually recognizes my phone now lol. So what do I do now?
nav200 said:
wow it actually recognizes my phone now lol. So what do I do now?
Click to expand...
Click to collapse
restart ODIN. Reread the thread you were using and check and double check the settings.
If you can boot your ROM. And still on stock. Use this thread.
Related
Hi
I may have bricked my phone.
So I did what everyone did this morning and flashed ep1q via cwm.
I got the boot loop.
Then I tried via odin.
Odin gets stuck at Initialization.. I waited for 30 mins before yanking and trying again.
I have now tried just to get a working phone using PIT file and stock roms.
When I turn on the phone I do not get the samsung splash screen. I get a computer and phone icon with a line connecting them.
Anyone have a suggestion?
trackie said:
Hi
I may have bricked my phone.
So I did what everyone did this morning and flashed ep1q via cwm.
I got the boot loop.
Then I tried via odin.
Odin gets stuck at Initialization.. I waited for 30 mins before yanking and trying again.
I have now tried just to get a working phone using PIT file and stock roms.
Anyone have a suggestion?
Click to expand...
Click to collapse
mods please move to general...
now did you get it to work with a stock rom?
get your file from another source.
if you are on a desktop try putting the usb in the back of your tower.
make sure you have the correct drivers installed
maybe try a diff usb cable?
just a few ideas. hope it helps
Follow these instructions. Use files below.
http://forum.xda-developers.com/showpost.php?p=16587971&postcount=493
ED1 - http://www.multiupload.com/LNTF3IKJ21
PIT - http://www.mediafire.com/?kk62yxpp8b8x918
trackie said:
Hi
I may have bricked my phone.
So I did what everyone did this morning and flashed ep1q via cwm.
I got the boot loop.
Then I tried via odin.
Odin gets stuck at Initialization.. I waited for 30 mins before yanking and trying again.
I have now tried just to get a working phone using PIT file and stock roms.
When I turn on the phone I do not get the samsung splash screen. I get a computer and phone icon with a line connecting them.
Anyone have a suggestion?
Click to expand...
Click to collapse
Odin a pit file also and repartiton. dont give up and also next time u have to post this in the general section
thanks for the ideas.
I will try them when I can
to clarify phone is not working.
Can get to the download screen but using odin 1.82 I get stuck at initializing part.
Turning on the phone normally I get phone and computer icon with a line connecting them.
trackie said:
thanks for the ideas.
I will try them when I can
to clarify phone is not working.
Can get to the download screen but using odin 1.82 I get stuck at initializing part.
Turning on the phone normally I get phone and computer icon with a line connecting them.
Click to expand...
Click to collapse
No clarification needed. We have all seen that screen. It means your recovery is broke, you need to ODIN a stock image and start over. Check out the thread entitled "How to Fix Your Phone"
Can someone please help me?
Every time I try to flash a ROM using ODIN, it gets stuck on the movinand.bin.
My phone also says, "RX_TIMEOUT" in red.
I can't get past this. I'm stuck. Can someone please give me some assistance.
Make sure you put the battery back in after you get it in download mode. And use the stock ee4 and the pit file when you flash.
Sent from my SCH-I510 using Tapatalk
I've done both. I use a PIT file, and a stock EE4 to return the phone back to factory state.
Everything seems to load up fine, then gets stuck on factoryfs.rfs.
Phone again shows RX_TIMEOUT.
Is it possible that it has something to do with running it in bootcamp on a macbook?
sushi_stalker said:
I've done both. I use a PIT file, and a stock EE4 to return the phone back to factory state.
Everything seems to load up fine, then gets stuck on factoryfs.rfs.
Phone again shows RX_TIMEOUT.
Is it possible that it has something to do with running it in bootcamp on a macbook?
Click to expand...
Click to collapse
Could be. You might try a windows machine.
Sent from my SCH-I510 using Tapatalk
hoppermi said:
Could be. You might try a windows machine.
Sent from my SCH-I510 using Tapatalk
Click to expand...
Click to collapse
AKA a real computer
Sent from my GT-P1000 using XDA App
Please help me. My Infuse 4G doesn't boot. All I see was light on the button. This what happened. I want to go back to stock and use [ODIN][UCKE3] Return to stock (Updated 06/08/11) by gtg465x . I right click on Odin and run as Admin. Odin see my phone on a download mode. I select infuse.pit on PIT, PDA in Pda, and Phone in Phone. then click Start. It got stuck at factory.fs (don't remember the name actual name). It stuck there for so long, maybe like an hour. Then I decide to unplug and pull battery out. close the Odin and redo the step again. This time the status bar went half way and then got stuck again. I left it overnight just to see if it's actually finish and it never did. Just stuck there. Turn the phone on and i only see light on the button. Is my phone dead? I can still able to get to download mode but the phone won't boot.
I done return to stock so many times and was successful. This was the first encounter I had where Odin stuck and never complete it flashing.
Try things like reinstalling the drivers, another pc, another usb cable etc.
Thanks. Will try that and also i will try this [ODIN][UCKD5] Odin - Stock (100% or Root+3e) - (Update 06/05/11) since on FAQ #4 seem to be in my case. But if members had other recommendation, please post. thx in advance
cat2115 said:
Thanks. Will try that and also i will try this [ODIN][UCKD5] Odin - Stock (100% or Root+3e) - (Update 06/05/11) since on FAQ #4 seem to be in my case. But if members had other recommendation, please post. thx in advance
Click to expand...
Click to collapse
Getting stuck on the factory.fs is pretty common here. You might try charging for a bit to see if you can get it to show signs of life. And that link up there^^^(UCKD5 Stock+Root+3e) has worked for me when gtg's didn't. Read the instructions for it carefully as you don't have to check as many boxes. You only need to load the file into the PDA slot. Also if you didn't have the drivers installed your phone wouldn't show up, so that's not your problem (although you could try re-installing them for **** and giggles)...
If THAT doesn't work try Adam's Heimdall one click HERE
If all else fails try a different PC. I had to and it worked like a charm.
Good Luck
Just my 2ยข
Sent from my SAMSUNG-SGH-I997 using XDA App
I had a similar problem last week I tried on my dads computer, nothing, then went to my computer since my computer had the drivers already on it cuz I used it to put music on my sd card it read it fine and they process went smoothly, so try on a computer that had had it
plugged it in before the problem and if it doesn't find threw phone restart they computer and re put the phone in download mode and try again and keep doing that till it recognizes the phone and it should work then
Sent from my SAMSUNG-SGH-I997 using xda premium
Some times just trying a different USB port on the same computer will help to. Not sure why but on my laptop the USB port on the right my Captivate did not like for flashing but the one on the left side always worked right.
Thank you all for helping me out. My infuse is now back in business. I use [ODIN][UCKD5] Odin - Stock (100% or Root+3e) - (Update 06/05/11) but this one got my phone to always boot in recovery mode no matter what i did. So i decide to try Heimdall One-Click Back-To-Stock UCKJ4 + Easy CWM install [2.3.6] (FOR AT&T USERS) and then flash LinuxBozo's Defuse 1.5 kernel. Successfully flash it . However after using Heimdall One-Click, ODIN did not see my phone when it's in download mode. Besides that, everything went well.
cat2115 said:
Please help me. My Infuse 4G doesn't boot. All I see was light on the button. This what happened. I want to go back to stock and use [ODIN][UCKE3] Return to stock (Updated 06/08/11) by gtg465x . I right click on Odin and run as Admin. Odin see my phone on a download mode. I select infuse.pit on PIT, PDA in Pda, and Phone in Phone. then click Start. It got stuck at factory.fs (don't remember the name actual name). It stuck there for so long, maybe like an hour. Then I decide to unplug and pull battery out. close the Odin and redo the step again. This time the status bar went half way and then got stuck again. I left it overnight just to see if it's actually finish and it never did. Just stuck there. Turn the phone on and i only see light on the button. Is my phone dead? I can still able to get to download mode but the phone won't boot.
I done return to stock so many times and was successful. This was the first encounter I had where Odin stuck and never complete it flashing.
Click to expand...
Click to collapse
I was stuck in Samsung logo. And cannot get into the Download mode. Could you help me with that? Or anyone?
pkayrat said:
I was stuck in Samsung logo. And cannot get into the Download mode. Could you help me with that? Or anyone?
Click to expand...
Click to collapse
What have you tried so far to get in to Download mode?
Sent from my SAMSUNG-SGH-I997 using XDA App
Galaxy Skyrocket phone was running custom rom
decided to return to samsung official rom. Connected the phone to odin was in process of bringing to factory rom thats when BY mistake i disconnected the cable from phone. I tried the process again would not work stuck at "firmware upgrade encountered ad issue. Please select recovery mode in Kies & try again. Message reads
I tried the power button volume up and down nothing is working. NEED HELP!
When you see that error screen your still in download mode. Plug back into computer and reflash the odon tar again. Be careful this time
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
Yeah it will say error select recovery mode in keys.
But your still in dl mode. I have pulled the cable during odin atleast ten times
Your fine just proceed
no. on the top screen says odin mode. product name:sgh-i727
custom binary download: yes (2 counts)
current binary:custom
and the rest message says, Please select recovery mode in Kies & try again
On the screen does not say downloading mode just the error message. will try the the odin and refresh tar.
dahraf said:
On the screen does not say downloading mode just the error message. will try the the odin and refresh tar.
Click to expand...
Click to collapse
Your not reading what were trying to tell you. That is still download mode. Flash the odin tar again
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
It'll happen again and again if you flash often. It may not say download mode BUT IT IS. Simply unplug your phone. Open Odin. Flash. Wait. It will work I promise. If u were fully bricked you would have no screen.
Sent from my SAMSUNG-SGH-I727 using xda premium
Got the phone working. Tried flashing several time didnt work. I changed to another USB port and flashed with ODIN and all worked good. THANK YOU ALL FOR THE HELP.
dahraf said:
Got the phone working. Tried flashing several time didnt work. I changed to another USB port and flashed with ODIN and all worked good. THANK YOU ALL FOR THE HELP.
Click to expand...
Click to collapse
Sweet, glad you got her running
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
dahraf said:
Galaxy Skyrocket phone was running custom rom
decided to return to samsung official rom. Connected the phone to odin was in process of bringing to factory rom thats when BY mistake i disconnected the cable from phone. I tried the process again would not work stuck at "firmware upgrade encountered ad issue. Please select recovery mode in Kies & try again. Message reads
I tried the power button volume up and down nothing is working. NEED HELP!
Click to expand...
Click to collapse
Give this a try. It works great!
http://forum.xda-developers.com/showthread.php?t=1342348
My infuse was running aokpcb rom. i made a backup of my previous rom, AEON v1.3.1. i restored using nandroid back to AEON but when i reboot its stuck at the samsung screen. I tried GTGs Odin back to stock multiple times using different ports but it always gets stuck at factoryfs. i even rebooted the computer and tried it again but still no good. I've used Odin back to stock a couple times before so im used to the program. now ive ran out of ideas and i would greatly appreciate the help. THANKS
Try heimdall...
http://forum.xda-developers.com/showthread.php?t=1524081
If that doesn't work 'I' don't know what to tell you
Sent from my SAMSUNG-SGH-I997 using XDA
And don't restore with nandroid, just to a full restore back to stock with odin or hemdall and reflash the rom.
Im not 100% but i think with aeon the first boot will freeze up at the factory screen. Try pulling battery then reboot..
Sent from my SAMSUNG-SGH-I997 using XDA
isaiahe97 said:
Try heimdall...
http://forum.xda-developers.com/showthread.php?t=1524081
If that doesn't work 'I' don't know what to tell you
Sent from my SAMSUNG-SGH-I997 using XDA
Click to expand...
Click to collapse
+1 odin sux. it's funny how some independant guys can reverse engineer what it's doing and write something better.
Happens to my Infuse all the time now, even using Heimdall. I just pull the battery, get back into the alternate download screen, reload the drivers (if necessary) on the pc and re-run Heimdall. It always seems to get stuck twice, but works the third time. The last time I took it to stock & did a "factory data reset", just to see if that would clear up whatever the issue was. Unfortunately (?), I haven't tried going back to stock since.
Dani897 said:
+1 odin sux. it's funny how some independant guys can reverse engineer what it's doing and write something better.
Click to expand...
Click to collapse
Not sure if your being understood.
Sorry for not responding. I've been at a summer camp for the past week. Anyways, when i try to install drivers with heimdall it aborts the procedure and then freezes the program... and when i plug in my phone into the wall charger, the screen stays off..
Young_Khalifa said:
Sorry for not responding. I've been at a summer camp for the past week. Anyways, when i try to install drivers with heimdall it aborts the procedure and then freezes the program... and when i plug in my phone into the wall charger, the screen stays off..
Click to expand...
Click to collapse
Heimdall is great when properly set up and WHEN IT WORKS. What I do, and this'll bring it back from pretty much anything, is use gtg unbrick, and if it doesn't boot from that flash, (and mine doesn't because its a rogers ) , i then flash the Odin stock lb3 pack, and boom back to normal no matter what I flashed. I imagine if you're running an at&t model , you shouldn't have to do the second step. Be sure to remove the battery and reinsert at least once on any from flash to be sure its not booting correctly before going to another step. Also be sure drivers are correctly installed through kies or kies mini. I find this is easiest with Odin because it clearly shows you in bright yellow that the download connection has been established.. many times i' very had to reinstall the kies drivers, I don't know why.. but try this , and like I say once you see yellow in Odin in phone download mode, you know you're set. Once again, like this kies/gtg/try booting/if no boot/pull battery try boot again/ if still no boot Odin lb3 stock and then flash a recovery kernel to regain cwm..
Sent from my SGH-I997 using XDA Premium HD app
ive been trying the odin lb3 from gtg and it gets stuck on dbdata.rfs instead.. im kinda flipping out...
Need some help. Step dad's Infuze is boot looing at the samsung logo. Searched and found qkster's thread about using heimdall 1 click to flash UCLB3. Got the phone into dl mode, loaded drivers and started flashing. Stopped at kernel upload failed. Ending session. Don't know what to do, can I just unplug and start over? Thanks in advance for any help.
Rebooted into dl mode, now it is showing firmware upgrade encountered an issue. please select recovery mode in kies and try again. Please help, is this still fixable?
I can get the phone recognized by Heimdall, just that it stops when loading the kernel. Is there another way to load kernel when in the dl mode?
merikgvr4 said:
I can get the phone recognized by Heimdall, just that it stops when loading the kernel. Is there another way to load kernel when in the dl mode?
Click to expand...
Click to collapse
use a different usb data cord
qkster said:
use a different usb data cord
Click to expand...
Click to collapse
Ok will do.
Got bootlloader installed no more rainbow now bootlooping at att rethink possible.
Sent from my SGH-I897 using xda app-developers app
still bootlooping at att rethink possible. I can get into e3 recovery. Can I just load any of the roms with this recovery to fix the bootlooping? Please help, wanna get done with this. Thanks in advance.
merikgvr4 said:
still bootlooping at att rethink possible. I can get into e3 recovery. Can I just load any of the roms with this recovery to fix the bootlooping? Please help, wanna get done with this. Thanks in advance.
Click to expand...
Click to collapse
Try running again and again if necessary until flashes and boots into ROM then Use one of the kernels in the same thread of qkster's that includes root and CWM recovery
Keep trying different ports, different USB cables, reboot computer,use different computer if available
elbscorp said:
Try running again and again if necessary until flashes and boots into ROM then Use one of the kernels in the same thread of qkster's that includes root and CWM recovery
Keep trying different ports, different USB cables, reboot computer,use different computer if available
Click to expand...
Click to collapse
Thanks will try different ports. I'll use the ones in the back next
Sent from my SGH-I897 using xda app-developers app
merikgvr4 said:
Thanks will try different ports. I'll use the ones in the back next
Sent from my SGH-I897 using xda app-developers app
Click to expand...
Click to collapse
either odin or heimdall works. you have to believe that. the frustration is getting a pc with usb port and a usb cord and your phone to align and work correctly. usually after a few driver install or java update or reboot..something works.
your other situation where you kinda had it recognized and almost completed a flash, try different usb cords. hold it steady, wipe the ports..etc..connection is prolly loose
qkster said:
either odin or heimdall works. you have to believe that. the frustration is getting a pc with usb port and a usb cord and your phone to align and work correctly. usually after a few driver install or java update or reboot..something works.
your other situation where you kinda had it recognized and almost completed a flash, try different usb cords. hold it steady, wipe the ports..etc..connection is prolly loose
Click to expand...
Click to collapse
Yeah frustrating it really is. Will fire up the old xp boxen and see if I get better results with that.
While reading up yesterday, I saw some posts about corrupted efs causing the att screen bootloop. Is there anything else?
I don't think it is a power button problem as the phone doesn't turn on when I insert the battery.
Finally, you think it is safe to use a custom rom if the stock one is bootlooping on the at screen?
Thanks again, will go back to reading and trying stuff after dropping off my son to daycare.
:good: