I am trying to find out why my phone is doing this? Could it be a rom or kernel issue? I am running asop+ 2.2 rom and glados 2.7. Or could it be a radio issue?
Sent from my Nexus S using Tapatalk
Glados has a problem with rebooting while calling
It's a known issue in GLaDOS thread. However, some users get a lot of reboots, some never get one.
If you want a quick fix then try flashing another kernel.
Thanks any suggestions on kernals? I have had nothing but issues with matr1x and now it seems glados is giving me issues.
Sent from my Nexus S using Tapatalk
Known issues with GLaDOS. If you want to stay with GLaDOS, you can try:
-Up the voltage a bit if you are using liveoc (or disable liveoc)
-Don't overclock at all
-Disable deep idle
Or you could try matr1x again and maybe up the voltage 25mV across the board (except for 100 and 200mhz) as it is underclocked by default which your phone may not like. Otherwise i'd be trying netarchy, eugene's icup or francos kernel.
Harbb said:
Known issues with GLaDOS. If you want to stay with GLaDOS, you can try:
-Up the voltage a bit if you are using liveoc (or disable liveoc)
-Don't overclock at all
-Disable deep idle
Or you could try matr1x again and maybe up the voltage 25mV across the board (except for 100 and 200mhz) as it is underclocked by default which your phone may not like. Otherwise i'd be trying netarchy, eugene's icup or francos kernel.
Click to expand...
Click to collapse
Matr1x was a nightmare....but I will try some of the others.
Sent from my Nexus S using Tapatalk
djwyman said:
Thanks any suggestions on kernals? I have had nothing but issues with matr1x and now it seems glados is giving me issues.
Sent from my Nexus S using Tapatalk
Click to expand...
Click to collapse
I'd suggest you start with Eugene's kernel (ICUP) because I have used it for a week without a single reboot
Disable deep idle, fixes most problems.
99 problems but a deep idle ain't one.
I switched to icup and it seems to be doing good. Thanks guys. I never had deep idle enabled so that was not my issue
Sent from my Nexus S using Tapatalk
djwyman said:
I am trying to find out why my phone is doing this? Could it be a rom or kernel issue? I am running asop+ 2.2 rom and glados 2.7. Or could it be a radio issue?
Sent from my Nexus S using Tapatalk
Click to expand...
Click to collapse
I'd try to upgrade to ICS or reinstall the ROM. Also check your battery. It it heats abnormally, that might be the issue as well...
Aosp+ 2.2 is ics... but regardless changing kernels fixed the issue.
Sent from my Nexus S using Tapatalk
has anybody had this problem with the CM9 20p1 alpha? My phone rebooted twice just now. Really annoying!
zyrill said:
has anybody had this problem with the CM9 20p1 alpha? My phone rebooted twice just now. Really annoying!
Click to expand...
Click to collapse
I'm on cm9 a20p1 and glados 2.7 and not a single reboot in 1.5 days now. Still testing though.
Sent from my Nexus S using xda premium
djwyman said:
Matr1x was a nightmare....but I will try some of the others.
Sent from my Nexus S using Tapatalk
Click to expand...
Click to collapse
Couldn't handle the Matrix eh?
Haha
Is this v14.0?
Sent from my Nexus S using XDA App
Pretty ironic, considering if you read my thread most people are happy with 14.
Sent from my Nexus S using XDA App
Yeah idk why you would be having problems with matrix, I doubt it's the kernel.
flodb113 said:
I'm on cm9 a20p1 and glados 2.7 and not a single reboot in 1.5 days now. Still testing though.
Click to expand...
Click to collapse
Did you try to have prolonged phone calls as well? That's when it crashed... Every 3 minutes or so. The rest is perfectly fine...
Related
I have skyics 7.4 running great. I just flashed faux 10m kernel and bam my auto rotation is reversed. I meant when I hold phone in portrair, it display landscape and vice versa.
Anyone know how to fix this issue? I tried to search but couldn't find a definitive answer. BTW, I have ATT skyrocket phone.
Many thanks
It sounds like you don't have the correct kernel for the Skyrocket. Is this the Kernel you are using?
http://forum.xda-developers.com/showthread.php?t=1437563
If so, that is the same combo I am using with no issues.
rac2max said:
I have skyics 7.4 running great. I just flashed faux 10m kernel and bam my auto rotation is reversed. I meant when I hold phone in portrair, it display landscape and vice versa.
Anyone know how to fix this issue? I tried to search but couldn't find a definitive answer. BTW, I have ATT skyrocket phone.
Many thanks
Click to expand...
Click to collapse
You flashed the wrong version
Dimarini said:
It sounds like you don't have the correct kernel for the Skyrocket. Is this the Kernel you are using?
http://forum.xda-developers.com/showthread.php?t=1437563
If so, that is the same combo I am using with no issues.
Click to expand...
Click to collapse
No doubt, that is where I got the kernel file. I re-downloaded again using your link, but this time I'll use the 10u.
rac2max said:
No doubt, that is where I got the kernel file. I re-downloaded again using your link, but this time I'll use the 10u.
Click to expand...
Click to collapse
You can use the 10m, but use the one for the skyrocket and not the t989
Now I'm doubtful. I might have downloaded a wrong version. I re-downloaded from link above and now works like butter.
Deep sleep helps so much in lessening battery consumption. Any other good benefits from faux kernel?
Many thanks esp seanz and faux for awesome ROM n kernel.
Sent from my SAMSUNG-SGH-I727 using XDA App
rac2max said:
Now I'm doubtful. I might have downloaded a wrong version. I re-downloaded from link above and now works like butter.
Deep sleep helps so much in lessening battery consumption. Any other good benefits from faux kernel?
Many thanks esp seanz and faux for awesome ROM n kernel.
Sent from my SAMSUNG-SGH-I727 using XDA App
Click to expand...
Click to collapse
Underclocking and undervolting
Could anyone suggest me best rom and kernel combo for Nexus S? Im pretty new in this. Hope tofind help here Thanks
Cyber is a good rom.
Sent from my Sexy Sexy Nexus S
cyberGR ? and whats best kernel for it ?
Bugless Beast Pixel Edition + Franco Kernel.
As a noob who has tried many combo, this is most stable and fast.
air kernel
I use Brainmaster's CM9 with Matrix 19.0
Its very stable, and pretty smooth.
I've used CyberGR v10, but i prefer Brainmaster's Rom over his. (had a lot of issues with his Rom)
Will try these. You can suggest more combos and links please. Thanks alot
Sent from my Nexus S using XDA
Me always use bugless beast...with pete alfonso kernel..very smooth
Sent from my GT-I9100 using xda premium
Trinity kernel and Rascream combo is pretty awesome
RasCream and any Trinity kernel
Rascream rom http://fitsnugly.euroskank.com/rascream/?id=crespo
Trinity kernels http://www.derkernel.com/ics-crespo.php
Currently using the latest cm9 skankwich with Trinity, loving the speed and battery. Gaming works wonderfully.
Sent from my Nexus S using Tapatalk 2
simms22 said:
RasCream and any Trinity kernel
Rascream rom http://fitsnugly.euroskank.com/rascream/?id=crespo
Trinity kernels http://www.derkernel.com/ics-crespo.php
Click to expand...
Click to collapse
what version of trinity kernel?
wuggy said:
what version of trinity kernel?
Click to expand...
Click to collapse
this version of t144 http://goo.gl/SWiSR
simms22 said:
this version of t144 http://goo.gl/SWiSR
Click to expand...
Click to collapse
thanks alot
should i use any scripts? what app should i use for OC and how much should i OC?
simms22 said:
this version of t144 http://goo.gl/SWiSR
Click to expand...
Click to collapse
When I OC to 1.44 why do I get reboots while antutu bench test. When those knights with swords appears?
Sent from my Nexus S using XDA
wuggy said:
When I OC to 1.44 why do I get reboots while antutu bench test. When those knights with swords appears?
Sent from my Nexus S using XDA
Click to expand...
Click to collapse
it means that your phone cant handle the 1.44ghz cpu oc and 240mhz(20%) bus/gpu oc. not many phones can. every phone is different. some can oc high, some not so high, and some not at all. unfortunately, even though its the same phone, they can vary widely in performance.
aokp + matr1x
+1 derek.
AOKP build33 with Matr1x
AOKP B32 with air kernel. Runs quite nice. Although battery lasts only about 12h. On b31 with matr1x kernel I reached 15+h on my i9023 but it got unstable due to liveoc.
I like aokp a lot, but I am not sure about which is the best kernel. I think with the next milestone I will do a systematical test series.
Sent from Nexus S withTapatalk 2
I've download a couple of kernels like teuv, matrix, and air kernel. But I keep switching between them because I feel as if none of them are working....can someone suggest good solution?
Sent from my Nexus S
If your phone is like mine, you might want to make sure that the kernel you use is set for default voltages. Matr1x in particular won't run correctly unless I reset the voltages.
Eat at Joe's
Run the stock kernel.
Sent from my Nexus S using XDA
+1 on mathkid's suggestion. You're phone might be a stock-lover.
I attached the stock ICS kernel here, or you can check out the stockish kernels such as (click for download sites/link):
_thalamus
SimpleKernel
Franco's
Hope this helps!
I don't like the stock kernel either.
Sent from my Nexus S
sdhanjal15 said:
I don't like the stock kernel either.
Sent from my Nexus S
Click to expand...
Click to collapse
Maybe change handphone is the best option for you...
Sent from my GT-I9100 using Tapatalk 2
sdhanjal15 said:
I don't like the stock kernel either.
Sent from my Nexus S
Click to expand...
Click to collapse
trinity t132.. cant go wrong with that one http://goo.gl/q3CnT
well, unless your phone cant handle it. its great at 1.32ghz, and its great running at 1ghz.
Thanks for your suggestions!!! I think I'll try the stock kernels and see how it goes
Sent from my Nexus S
My phone only likes stock/simple, thalamus, and Pete's kernel. Every other one always gives me issues after a few days. Just stick with stock or modified stock, like thalamus as stated in another post.
Have you tried SimpleKernel by terryhau? Its the stock kernel with Voodoo and BLN added. Seems like a great solution for you.
http://forum.xda-developers.com/showthread.php?t=1420542
Sent from my Nexus S using xda premium
Is anyone using a different kernel with the new v21y baseband?
Faux's 14b 2.
buru898 said:
Faux's 14b 2.
Click to expand...
Click to collapse
14b2? I'm familiar with the g2x prior to baseband update but I've never seen that one...link?
Sent from my LG-P999 using XDA
Check on rootz, second to last post.
Sent from my LG-P999 using Tapatalk
Faux all the way.
http://forum.xda-developers.com/showthread.php?p=25924733
Sent from my LG-P999 using xda premium
I'm using the 14b2 faux123 kernel with v21y. It's a lot better than the stock kernel.
Sent from my LG-P999 using XDA
how's the battery life i don't want to loose my 3hrs screen on time using akop and faux
Sent from my LG-P999 using XDA
Sk8trfred said:
how's the battery life i don't want to loose my 3hrs screen on time using akop and faux
Sent from my LG-P999 using XDA
Click to expand...
Click to collapse
There you go.
Sent from my LG-P999
buru898 said:
Faux's 14b 2.
Click to expand...
Click to collapse
I'm using this kernel as well. I can confirm that it's much smoother and quicker than the stock kernel.
Sent from my Motorola StarTAC
andrewNY said:
I'm using this kernel as well. I can confirm that it's much smoother and quicker than the stock kernel.
Sent from my Motorola StarTAC
Click to expand...
Click to collapse
What about battery life?
Sent from my LG-P920 using XDA
cricketAC said:
There you go.
Sent from my LG-P999
Click to expand...
Click to collapse
Switch to a different browser if want to save more battery
Sent from my LG-P999 using xda premium
I the 014b2 kernel working with rc3? I can't get to load past the boot animation.
aaCotyaa said:
I the 014b2 kernel working with rc3? I can't get to load past the boot animation.
Click to expand...
Click to collapse
There are two threads/ variations of faux kernels. One is for GB like this one and the other is for cm7 based. Use the other kernel 050b1 i think.
cricketAC said:
There are two threads/ variations of faux kernels. One is for GB like this one and the other is for cm7 based. Use the other kernel 050b1 i think.
Click to expand...
Click to collapse
That one works with the new bb?
aaCotyaa said:
That one works with the new bb?
Click to expand...
Click to collapse
I dont think so cuz at that time cm7 wouldnt work with new BBz, dunnno if he patched it up(his kernel) later on.
cricketAC said:
I dont think so cuz at that time cm7 wouldnt work with new BBz, dunnno if he patched it up(his kernel) later on.
Click to expand...
Click to collapse
Just looked into it. Apparently 050 is for Rc2 only.
---------- Post added 2nd June 2012 at 12:06 AM ---------- Previous post was 1st June 2012 at 11:49 PM ----------
OK, I got it working. I flashed my old favorite Trinity kernel. I really didn't expect it to work, but apparently it does.
The Eaglesblood ICS release 3 came with Trinity Kernel and had UMS support They just updated to Supporting the V21Y baseband. going to try Harsh and see what happens
jimmydafink said:
The Eaglesblood ICS release 3 came with Trinity Kernel and had UMS support They just updated to Supporting the V21Y baseband. going to try Harsh and see what happens
Click to expand...
Click to collapse
That would explain it then lol
I running T15-G2x-06022012 with CM7 RC3 OCed to 1400 with out issues
For Faux's 014b2 kernel, which do you recommend when running Kwes' modified stock ROM (v21y)? I see pre-UV and stock voltage versions. I'm leaning towards stock voltage, but is there a major advantage for the pre-UV? (I'm not even really sure what is meant by pre-UV -- pre-under voltage?)
Thanks!
EDIT: pre-UV is pre-under volted. From a little more reading, I found that pre-UV means the kernel has a -50mv UV already. So if using UV/OC tools and apps, you need to take into account that -50mv already.
http://forum.xda-developers.com/showpost.php?p=14887835&postcount=262
Hopefully this explanation helps anyone else with a similar question.
Anyone else still getting lockscreen freezing with sweep2wake? Is there any way around it besides disabling sweep2wake. I absolutely love it, but after my phone has been in my pocket for a while it'll freeze at the lockscreen and become unresponsive. No problems when its disabled. Currently running latest versions of viper rom and beastmode kernel.
Any help would be appreciated.
style2burn said:
Anyone else still getting lockscreen freezing with sweep2wake? Is there any way around it besides disabling sweep2wake. I absolutely love it, but after my phone has been in my pocket for a while it'll freeze at the lockscreen and become unresponsive. No problems when its disabled. Currently running latest versions of viper rom and beastmode kernel.
Any help would be appreciated.
Click to expand...
Click to collapse
Its a known bug, as far as I know there isn't any fix yet.
Not once i have experienced freezing on lockscreen. Using viperxl 2.2 with elemental kernel 2.0, been 2 weeks usage
Sent from my HTC One XL
I've been using the beastmode kernel and once in a while I have that issue, Display freezing when waking the phone. I can confirm all the buttons are working. ie volume up.down and power button.
I'll try the Elemental X 3.0 and will see if the issue is solved or not.
I get this issue with s2w on beastmode and rohans kernel. I ended up just going back to stock kernels
Sent from my HTC One XL using xda app-developers app
Hasn't happened to me. Been using ElementalX and it works great.
i had been experiencing this too, so I can confirm your issues. I have searched the forum and google and have not found a solution yet
Happened to me with beastmode 4.4 on viperxl 2.3.1
Went back to stock kernel
Sent from my HTC One XL using xda app-developers app
Only if I wipe screen with a damp rag, when cleaning it.
WR
Sent by WR's O/C'd One-XL on CR-V
What governor/kernel are you using? I would notice lag/freezing when using the more conservative kernels, also when undervolting to -75mv. So i switched to Intellidemand and -50mv undervoltage.
elsupermang said:
What governor/kernel are you using? I would notice lag/freezing when using the more conservative kernels, also when undervolting to -75mv. So i switched to Intellidemand and -50mv undervoltage.
Click to expand...
Click to collapse
I'm using intellidemand, and I think beastmode is stock UV -50, -12.5 more that I added, so thats 62.5UV total. I can try turning off UV
is s2w issue only with beastmode or is it with elemental too?