Database Info

urgent help needed

hi there
i am using imate jamin da problem with my cell is
i upgraded my rom to qtek 2.20000 it was working absolutely fine with 8 icons in my comm manager then i upgraded to RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-b1 and it has severely damaged my cell as my phone my phone hangs white booting it shows me the colour screen with
IPL 1.00 and SPL 2.20.0001
on the Screen
OS and GSM is not displayed
I tried rom update several times but its not working
i tried to update my rom through boot loader mode but again failed
i even tried to format my phone but it gives FAT16 format failed
I even tried to upgrade to jesters RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1 but still its not working and givng same problem
now i dont understand what to do
guys please give me Advice and solution for this g3 g4 Problem
i even tried sending my phone to service center but stupid people dont know how to solve it and they returned me back
Thanks in Advance

You have bricked your phone... You just can't install a G4 rom on a G3 phone... Different chipsets are the cause of the problem... Sorry

you mean to say its over ?????????????
there should be any way

You'll have to wait to see if Jesterz manages to produce a goldcard...
BTW a goldcard it's basicly a mem card with a rom in it that autoinstalls itself thus no need for the usb connection... This fits your case cause you don't have an active usb conection because of the driver/chip conflict...

wrong software
I have the same problem i tried to flash my g3 with jesters RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1 by mistake and it was ok until the end of process when i finich it with congratulations and bla bla my device stills in the bootloader mode all the time. I can now connect and start to flash but when it comes to 80% of the process it stops with error 360 wrong command. Pleas is there any help for some kind of downgrade flash or so because it can only get boootloader but never start with software. When I try with jesters RUU-Prophet-g3-AKU2.2-2.20-2.47.21-Jester-r1 the whole process finish ok but the phone stills in bootloader. The same thing is also with RUU-Prophet-g4-AKU2.2-2.20-2.47.21-Jester-r1 I can not execute step2

that's why you should read the "sticky" first before you do it.
I have a Dopod 818Pro from a friend of mine but in Chinese ROM, so I have to read a whole nite the sticky and found out what is my Dopod version, finally I found it is G3, so I did all the steps, from unlocked the CID till upgrade to Jester latest ROM for G3 and skip the G4.

please help
Yes i realy know that it was my fault and my big mistake so i vould not do it again but now i need help because it stills in bootloader i i can even start flashing the device that gives me hope that some kind of recovery is maybe possible.

Yes i also commited this mistake its my fault but i really need help my device still enters into bootloader mode.

ur problem
there is nothing to do anymore u have to wait u CANT DO ANYTHING ITS OVER

how do you mean it is over. Do you think that could not repair it. Is it possible with sd card or jesters gold card and how. Help me please if somebody knows

there must b some way to overcome this problem

jesterz's gold card isn't working yet, and for now it's only for G3...

My hardware is G3 but flashed by mistake with G4 and now is in bootloader mode so i can start flashing but i do not know with what and how. Could you please explain me how and where can i find and use goldcard for g3 if possible Thanks

have u tried holding the camera button while softreset and then flash rom again

Yes sure i tried to flash rom from jesters for g3 which is for my device instead jesterz g4 what i used by mistake and it passed ok but when i restart it stills in bootloader mode only, so i could flash but do not know which firmware should i use

i've the same symptomes as mjankovic and aarif_ziaee, (bricked my phone)
but the only things i think i've forgot, is to cid unlock my device before doing the step 2
i have a question.
i have the rom PDAMobiz_Prophet_WM5AKU3.3_v3301
(witch is not an auto installable tile, it's a folder containing exe, dll, bat and nb file)
is it possible to install it by using teraterm pro or mtty? (connected and install bats and cabs by thoses software)
ps : i'm sorry for my bad english, i'm french not going to my languages faculty since i'have bricked my phone. need to fix it soon !

dopod 818pro dead?

when i flashing my dopod , my house suddenly blackout.
So what happened to my dopod is that i stuck at IPL, SPL , GMS , OS page, and it didnt load windows anymore.
I tried to hard reset it , but it helpless
I can go in bootloader.
Is their any possible way to install a fresh rom into it?
Searched around , but found nothing. Pls help up

try this
1) hold your communication button and soft reset *keep holding comm-button until see the RGB color bar,
2) plug-in your USB cable, u will see a 'USB' appear at your bottom left,
3) install the flash ROM from your window.
well I tried install WM6 once fail, so I do the above step, and 2nd time successfully upgrade to WM6, you can use back your original ROM download form dopod site.
goodluck

feiyee said:
when i flashing my dopod , my house suddenly blackout.
So what happened to my dopod is that i stuck at IPL, SPL , GMS , OS page, and it didnt load windows anymore.
I tried to hard reset it , but it helpless
I can go in bootloader.
Is their any possible way to install a fresh rom into it?
Searched around , but found nothing. Pls help up
Click to expand...
Click to collapse
It's easy, mail your dopd to me.

Htc s710,help needed

Hey guys,Yesterday i wanted to update my rom.I have windows mobile 6.1.Apperently with the new rom it makes it faster.I unlocked my device and tried loading the softawre on.Everytime i try loading it ,the computer says it lost the connection with the pc.Today i tried using my phone and when i switch my phone on ,the phone does not respond and the screen has three colour(blue,red etc).How do i get into my phone or reset it so that i can use my existing rom and windows?e-mail me anytime

You're stuck in Bootloader
Hi
Your phone is stuck in Bootloader Mode. You may find that by removing the battery and re-inserting it you will get to a position of loading Windows Mobile. The Bootloader is the software on the phone that is used to install a new operating system. If you search for "Stuck" and "Bootloader" on the forum or the section of your device you will probably come up with some threads about this problem.
The worst case scenario is that the "flash" of the new operating system has gone wrong so the Windows Mobile operating system can not load. If this is the case, the phone will automatically revert to the Bootloader as it can't "see" any system installed. Think of a PC reverting to the BIOS and giving you the message "Operating System Not Found" if you remove or disconnect the hard drive.
If you can't boot simply be doing a soft reset using the stylus in the hole you need to successfully flash a new Operating System or ROM. Check out the Encyclopedia at the bottom of the main forum page if you don't understand any of the words I've used here. If you can be more specific about your device and the ROM you tried to flash others may be able to help.
Cheers
andrew-in-woking

Help
Hi,how do i flash when i dont have excess to windows itself?The colourful screen comes on immidiately when i start my phone!!

XZ5J4H said:
Hi,how do i flash when i dont have excess to windows itself?The colourful screen comes on immidiately when i start my phone!!
Click to expand...
Click to collapse
Welcome to the forum
Please READ the Wiki: http://wiki.xda-developers.com/index.php?pagename=HTC_Vox
Over there you´ll dind a way to flash your device
Good luck,

Stuck windows
Hi,I managed to load mono lisa windows 6.1 on my phone.I did this by justing loading utility update file.Followed all the intructions.After the rebooted it just goto stuck.I tried taking the batery out and inserting it back in the phone after 10 seconds.The problem is when i start my phone it gets stuck and the everything in unresponsive.Help me please!!1

Hard Reset or Reflash
Hi
After flashing a ROM you always need to perform a manual Hard Reset. Read the Wiki page on your device for info on how to do this. If that doesn't help then you may have a bad flash. If this is the case then flash the ROM again but as soon as it's done perform a manual hard reset.
If you still can't get it working flash an official operators or HTC ROM to your device.
G'luck!
andrew-in-woking

Rom Wanted
Hi Guys,what is the latest and best rom for a htc s710 today?I want to upgrade.Please help!!Want something that also makes my phone faster.Currently have the VOXrOMwM6.1 cLEAN_V1.3

XZ5J4H said:
Hi Guys,what is the latest and best rom for a htc s710 today?I want to upgrade.Please help!!Want something that also makes my phone faster.Currently have the VOXrOMwM6.1 cLEAN_V1.3
Click to expand...
Click to collapse
Enter to Vox forum and READ a little about all ROM´s there.
The best way is to test severals till you get the one fits your personal needs
Good luck,

Do You have Problem downgrade fr ROM 2.03 TX WWE

Hi all,
I'm Indonesian. My Device is XDA II Mini. A few weeks ago I have upgrade the ROM to 2.03 TX WWE, used it for about week. A problem appear when I tried to downgrade the ROM to the original one from seeo2.com site the PC tell the error 150 (I think its about the connection).
when I read this forum, i know the many people have the same problem with me.. and still not found yet the solution for solving this problem.
With this situation I made this new thread to share our problem in this thread. Its about the history from ROM 2.03 TX WWE, about the maker of this ROM and for the warning massage for anyone who wish to write this ROM to their device so they will think 100 times to use this ROM.
Lets join this thread and hope there be a nice guy who can solve our problem.
regards
Eric
Jakarta-Indonesia

Hello,
I have the same problem with my magician. I flashed so many times some ROMs on my Magician before without any problems. But since I flashed the 2.03TX ROM, there is no way to flash any ROM. I also can't reflash the 2.03TX ROM. It always says, that there is an Connection Error.
I tried to flash with the official Setup and also with the No_ID.exe, but there is no chance to do something.
The 2.03TX is a very nice Rom, but i want to use the programm "Phone Extender" on my Magician and it doesen't run with 2.03TX...
Please help us someone, I want an other Rom on my Magician!

Where is everybody.....
Please Help us hiek hiek hiek.... cry cry cry....
Does anyone can help us ?????
Pleeeeaaaaseeee......

The same problem, the 2.03TX WWE is a nightmare for me.

I haven't got any problem.
Flashed just last week tx203->TMobile112->wm61.
Very happy with everything, I am using XP and O2 mini

you should flash from bootloader.

I have problem after try flash wm6 from 2.03 TX WWE phone only boot mode ... any help .. I try to flash same rom but I give same error on country id

I have the same problem.
Solution is to enter to the bootloader mode somehow and downgrade to original not bigstorage rom and than flash new cotula rom.
If you can't enter to the bootloader mode with power+camera+reset buttons try to hold longer or rapidly press power+camera and then press reset a few times. I'm succeeded finaly...

to bootloader mode mean screen with serial or usb status ... my problem is I try more rom but any flash I don't have original rom ... what I do?

hello im from Indonesia too...
You can use magicianUpdt_NoID (or another name, i forgot)
you can search at xda-developers ftp..

I have no problem with mine.
When I flashed this ROM it got automatically flashed twice.. I don’t know what happen but it was successful

Hello
I was sucessfull.
There is a 2 step flash!!!
P-O

I try to use this too but nothing no flash ....

Try this rom: http://rapidshare.com/files/18876133/NL_11300_131_11200.exe
If this doesn't work tell me the error message...

ok this img of error the image 1 when start exe the other when stat update noid

jovan.asanin said:
I have the same problem.
Solution is to enter to the bootloader mode somehow and downgrade to original not bigstorage rom and than flash new cotula rom.
If you can't enter to the bootloader mode with power+camera+reset buttons try to hold longer or rapidly press power+camera and then press reset a few times. I'm succeeded finaly...
Click to expand...
Click to collapse
Mine keeps reseting everytime it should go into the bootloader screen.
I can force it, but then the update wont continue anymore.
How did you do it?
---Edit---
Nevermind, found the solution here, its the old vista driver bug... :/
http://forum.xda-developers.com/showthread.php?t=291723

I use xp ...

well... it worked on mine...
Try the driver thingy anyway and follow the instructions to the letter.

I try more and more but notuhing

Here's what I did step-by-step:
- Recharge the battery to at least 70% in a electric charger (not connected to the PC).
- Go into bootloader (press the power button +camera button without releasing and click the tiny little hole on the right bottom side of the device, next to the audio entrance).
- The screen goes black, that's normal, with the help of a bright light you can see its written on the screen "SERIAL" and "V1.02" (or something similar).
- Go into Active Sync on XP (or Windows Mobile Device Center on Vista) and uncheck the option "Allow USB Connections".
- Connect your pocket pc to the PC usb (its still in the bootloader screen, right?).
On Vista (I think XP can skip this step)--------------->
- Go to Control Panel > Administrative tools > Services and start the services "windows mobile device connectivity" and "windows mobile device 2003 connectivity", its they are already running thats ok.
- Now go to Control Panel > System > Device manager, find your mobile device and force the update of the driver attached here.
- Now, press Ctrl+Shift+Esc for Taskmanager and kill "WMDC.exe".
------------------------------------------------------------------->
- Download this rom (46mb): http://rapidshare.com/files/18876133/NL_11300_131_11200.exe (its in english WWE)...
- With Winrar, extract that EXE into a folder.
- Copy the MaUpgradeUt_noID.exe attached here into that folder, with the rest of the files.
- Run MaUpgradeUt_noID.exe.
- If all goes well the update will take a loooong time and pass thru three install bars, that's normal.
- After that it recommends a Hard-reset (Power button + reset at the same time).
Now your rom is official, and you should have no more problems.
Install the Cotulla WM6.1 rom: http://forum.xda-developers.com/showthread.php?t=492937
Based on: http://forum.xda-developers.com/showthread.php?t=291723

WM 6.5-Device doesnt boot anymore

Hello Guys,
yesterday i startet a backup-process with PIMBackup and i've chosen the wrong destination-path.
So it backed up all my Data to the root-Directory.
Now my Device doesnt boot anymore. It alwas hangs on IPL.
Radio an ROM-Version is shown.
Is there someone who got an idea, how i can delete files from my root-directory?
i have a htc touch Diamond.
Thank you very much!

Bootloader-Mode can be entered, i just dont want to flash the device again

I'm going to flash it again.
Thread can be closed/deleted