Database Info

Huawei Ideos Super FAQ

This is an FAQ for the Huawei Ideos as there have been many questions on how to do the same things. Hopefully this should help. There are other FAQs but this one tries to compile as many as it can into one FAQ.
Feel free to reply to this if there are any questions or if you want me to make any additions. The FAQ won't be complete to begin with but I will add as I get time.
One thing I will say is that I WON'T TAKE RESPONSIBITY IF YOU DAMAGE YOUR PHONE. I AM PROVIDING THE INFORMATION AND WILL TRY TO HELP YOU IF SOMETHING BAD HAPPENS BUT I CAN'T TAKE ANY RESPONSIBILITY
1. How to root the IDEOS
This can be done quite simply by adapting what quail wrote:
There is a couple away you can go about gaining root access with this phone I have tested all 3 ways but only had success with 2 of them.
a) You can download 'z4root' from here (WORKS)
b) Search the XDA forums for 'SuperOneClick' which requires mono to work on Linux. I have read people that have had success with 'SuperOneClick' but that was not the case for me. (HAVEN'T CHECKED)
c) My preferred method: (HAVEN'T CHECKED)
Prerequisite:
knowledge of Linux and Terminal
knowledge of ADB (guide available in forums)
I did all this using Debian (testing) 64bit, Android SDK.
Creating correct permissions to access the phone via USB:
i) create
Code:
/etc/udev/rules.d/51-android.rules
ii) in the file put
Code:
SUBSYSTEM=="usb", ATTR{idVendor}=="12d1", MODE="0666"
iii) then
Code:
chmod a+r /etc/udev/rules.d/51-android.rules
iv) restart udev or reboot
Downloading and/or Installing required software:
1) Downloading and installing the android-sdk from: developer.android.com/sdk/index.html
2) Downloading and extracting 'SuperOneClick' (you will only need these 5 files: rageagainstthecage, sqlite3, su, busybox and superuser.apk)
3) Copy rageagainstthecage, sqlite3, su, busybox and superuser.apk into the platform-tools directory of android-sdk. Put phone in debug mode.
4) From a terminal (command line) change to the android/platform-tools directory and carefully do these steps.
Check to see if adb can see your phone properly:
Code:
./adb devices
You should see the serial number of you device, if you see bunch of '?' you have done something wrong.
Now for the fun part rooting the phone: <= no phun intended hehe
Code:
./adb push rageagainstthecage /data/local/tmp/rageagainstthecage
Code:
./adb shell
Code:
cd /data/local/tmp
Code:
chmod 0755 rageagainstthecage
Code:
./rageagainstthecage
5) Now wait until you get kicked out from adb before you do the following:
Code:
./adb shell
If everything worked now you should see a "#" instead of the "$" you saw previously in the adb shell which means you shouldn't get "permission denied" in the following steps:
Code:
mount -o rw,remount /dev/block/mdtblock4 /system
Code:
exit
Code:
./adb push su /system/bin/su
Code:
./adb push busybox /system/bin/busybox
Code:
./adb push sqlite3 /system/bin/sqlite3
Code:
./adb push Superuser.apk /system/app/Superuser.apk
Code:
./adb shell
Code:
cd /system/bin
Code:
chmod 4755 su
Code:
chmod 4755 busybox
Code:
chmod 4755 sqlite3
Code:
./adb reboot
Now you should be able to use apps like 'Cache Cleaner NG', 'Root Explorer', 'SetCPU' etc that require root access to work correctly.
Enjoy​
2. How to flash the Ultrakiller Recovery Image
Now this has been covered many times but there have been a lot of problems with the BSOD on the IDEOS. A few days ago Ultrakiller came up with a solution that works regardless of the LCD type. Now this was distributed as an IMG file so many people were confused so here is a link to one with everything you need included. All I did was remove the amon'ra image and copied the Ultrakiller recovery IMG to the folder and edited the scripts to point to the new file.
After you download the file:
* Put your device in bootloader mode - turn it off, then press the power button while holding the 'Volume Down' and 'End (Red)' keys (Yes, bootloader is just the IDEOS logo) WHILE YOUR DEVICE IS PLUGGED IN
* WINDOWS - double click 'install-recovery-windows.bat'
* MAC - Open a terminal window to the directory containing the files, and type 'chmod +x install-recovery-mac.sh' followed by './install-recovery-mac.sh'
* LINUX - Open a terminal window to the directory containing the files, and type 'chmod +x install-recovery-linux.sh' followed by './install-recovery-linux.sh'​
See Q3 if you have Windows and the prompt hangs on "Waiting for Device"
3. How to solve problems with drivers on Windows in bootloader mode?
1. Unplug your phone
2. Download and install PDANet from here - at the end of the setup it will tell you to plug in your phone - do that
3. Put the phone into bootloader (See Q2 above)
4. Go to device manager and right click on "Android 1.0" and click "Update drivers"
5. Click "No, not this time" and Next
6. When it asks you where to look for drivers point it to PDANet's install location
7. Hopefully it should find the driver and prompt you to install it - it will take some time
8. You can now access your device in bootloader!​
Thanks to the following people:
Quail for the base of the guide and the ROM I'm using - it's amazing BTW
Ultrakiller for the recovery image
Changelog:
21/01/2010: Initial writeup
22/01/2010: Added Q3 and made some minor changes​

i unfortunately deleted a system app and upon restarting my phone it wont boot.....it keeps hanging at the startup and reboots.. help me how to system restore...

Hi - the Ultrakiller recovery IMG in the ZIP from the Link above is "Ultrakiller.img.img". Dunno if it didnt work cause of this - sry didnt test, just downloaded new Ultrakillers "UltraJack-Recovery_v4.6.2.img", saved into that folder and changed the .bat to "fastboot-windows.exe flash recovery UltraJack-Recovery_v4.6.2.img" and it worked for me Even superuser.apk didnt work for usb-root but z4root does it perfect and DroidExplorer showing files now .
Thanks so far to all investing their time here
P.S.: the HUAWEI background of Ultrakillers recovery is very delicious

General guide to Flash ROM
Can you please provide a detailed guide for flashing Huawei Ideos. Because it is super guide. So it must contain this topic also.
I want to flash official ROM on following link:
http://forum.xda-developers.com/wiki/index.php?title=Huawei_U8150_IDEOS
Waiting for your response

yrnehukuht said:
i unfortunately deleted a system app and upon restarting my phone it wont boot.....it keeps hanging at the startup and reboots.. help me how to system restore...
Click to expand...
Click to collapse
Dear have u find out the solution of this problem?? COZ im also suffering from this if u find it then plz tell me [email protected]

I have downloaded a rom from xda-developers wiki from this link
http://forum.xda-developers.com/wiki/index.php?title=Huawei_U8150_IDEOS
then updated my device software by going in to update mode(press vol up + end key + power button) .
This step returned me my original recovery.
But I am not going to recommend it bcoz i am facing problems like my cd drive which is automatically displayed has become inaccessible.
I am having problem to copy files to sd card.
My upgrade mode is not working now.
all these things were working immediately after the above mentioned process but I am now stuck with these things.
I think it is because i have flashed lower version number of rom on phone.
If you want to recover recovery mode only then I have successfully flashed UltraJack-Recovery 5.2.1 from this link
http://forum.xda-developers.com/showthread.php?t=860189&page=24
Inform about your progress

Thanx. Very useful

Hi guys. I am in a lot of trouble with my ideos.
Tried installing a custom ROm using ROM manager and it failed, although the original ROM is still there and its booting up and working perfectly.
However, when i try to boot into recovery, only the lit blackscreen shows.
I have tried everything from running ULTRAjack recovery on windows(which only shows 'waiting for device' on cmd, with the pdanet drivers installed) to ubuntu(which shows 'waiting for device' on Amon-ra recovery and permission denied on ULTRAjack).
Could it be i didnt root the device properly since i used z4 root?
Any more ideas?

900/2100 or 850/1700/1900/2100
Hello, How do I tell which sub-model my U8150 is please? Either HSDPA 900 / 2100 / AWS or HSDPA 850 / 1900 / 2100 / 1700. baseband = 22201003; build no.= U8150V100R001C183B825; IMEC = 355093040562676; IMEC-SV = 39.

Check out your fcc id suffix. I have heard there is a b version and a d version.

hi do flashing many roms affects my ideos mobile?

netskink said:
Check out your fcc id suffix. I have heard there is a b version and a d version.
Click to expand...
Click to collapse
All I got is a U8510-1, no letter... any thoughts?

Unlock u8150
Hello.
i have a T-Mobile Ideos u8150, also known as Comet.
it is locked to T-Mobile and requests a pin code when using another sim card.
is there a way to unlock the phone?
please help me...
thank you.

Enable USB Debugging & One Click Root with Unlock Root Tool

[REF] Axioo Picopad QGN (Root, Busybox, CWR, etc)

Axioo PICOPAD QGN
Android OS, v2.2 Frozen Yogurt
Qualcomm MSM7227 (App: ARM11 600MHz)
This wont work on PICOPAD 9
This is a very unpopular device from Indonesia. Although it is very easy to Root using "Superoneclick". As more people got hold of this free set(via Singapore old Starhub Internet plans), more people are also starting to ask about the steps on rooting this device. I thought I should start a guide here where I've followed from different places, piece them together here.
Feel free to comment and share if there are other ways to root, flash and install custom roms or android version. More importantly over clocked kernels. (remember seeing a link at kwbr's thread)
There are similar sets "CSL Spice Mi700 DroidPad", "Viewpad 7", etc
Alternatively you could research more by heading on to Viewpad 7's thread as I found out that device is very much similar and more developers are active there. I've also tried flashing kwbr's rom and it works for me.
Well if you are going to follow this thread to root, then read on...
WARNING! You warranty is now VOID & I will not be responsible if you brick your device.
Click to expand...
Click to collapse
Sections:
1. Rooting your device (wiki)
2. Installing Clockwork recovery (wiki)
3. Setting up ADB (optional)
4. Setting up partition on SDcard to free up device main space (WIP)
1. ROOT & Busybox (comes in a package)
Use these steps to root with "SuperOneClick". (Thanks to SuperOneClick)
Download and install "SuperOneClick"
Alternatively, download older version (some say works better) 1.6.5 1.7.0
Make sure you have .NET Framework v2.0 for Windows XP(win update)
On picopad, Unmount your SD card. From settings -> sd card -> unmount
Enable USB debugging, Setting -> Applications -> Development -> tick USB Debugging
Connect picopad to Pc via usb, ignore pctools if popup.
Goto Windows Explorer, Picopad will appear as "CD-ROM", explore CD-ROM and run SETUP.exe, ignore pctools
Open "SuperOneClick"
Change the option from "psneute" to "rageagainstthecage"
Click Root.
Rooted , Superuser & Busybox installed
Mount back your SDcard if u wish and reboot your device at least twice.
Congrats! Your device is rooted!
If you are satisfy with only root and superuser access, then you can stop here.
If you would like to install(flash) Clockworkmod recovery so you can backup your device(nandroid) and flash rom/kernel/stuff easier, proceed to step 2. (Highly Recommended)
If you want to set up ADB proceed to step 3 (optional, may come in handy and good for other android devices.)
2. ClockworkMod Recovery 5.0.2.6
2a. Preparing to installing CWR
Download CWR 5.0.2.6 and Flash_Image
Unzip, then copy "flash_image" and "cwm5026.img" to the root of your sdcard. (if you don't know how.. take your SDcard out and use a card reader)
Power on the device and install a terminal app so you could type commands in, try Android Terminal or Terminal Emulator
Once installed, open the app and start typing:
Gain superuser access type
su (once in superuser, you will see "#")
Click to expand...
Click to collapse
copy flash_image to system/bin
cp /sdcard/flash_image /system/bin
Click to expand...
Click to collapse
Install the flash_image
chmod 755 /system/bin/flash_image
Click to expand...
Click to collapse
Backup your original Recovery
cat /dev/mtd/mtd3 > /sdcard/orirecovery.img
Click to expand...
Click to collapse
And if you ever want to restore back for warranty issues
flash_image recovery /sdcard/orirecovery.img
Click to expand...
Click to collapse
2b installing ClockworkMod Recovery 5.0.2.6
The previous ver 2XXX is pretty outdated, thanks to mb-14 for sharing 5026.
Now you are ready to flash ClockworkMod Recovery
Assuming the file name that you download from CWR is "cwm5026.img" Type
flash_image recovery /sdcard/cwm5026.img
Click to expand...
Click to collapse
Done!
Now to run Clockwork Recovery:
First, turn off your device.
Now, hold down both volume button and press the power button at the same time, when you see recover on the corner of the screen, you can let go as you will boot up in Clockworkmod Recovery.
How to use 5.0.2.6 CWR?
Use the device vol+ and [/b]vol- to move up and down or the soft keys menu for "down", home for "up"
Select options by pressing the power button or , use the soft keys search for "enter"
back is for "back".
When you load into CWR, you could do many stuff, some simple info on the main options,
Wiping data is resetting your device to factory default, but CWR remains as long as you do not flash a stock recovery or a rom with a different recovery inside.
You could do stuff like formatting and partitioning SDcard to prepare for Apps to be install in SDcard to save space in device. Other than that, you could do a Backup for your entire device which is also known as nandroid backup, but it doesn't backup the bootloader and radio, so take note if you are going to flash custom radio or bootloader.
If you have a backup, you could restore back to that backup, this is good if you accidentally flash something bad or dislike a rom
Fixing permission is good if you always have FC.
You can mount SDcard to your pc from here and manage files with from your PC.
You could use ADB to push / pull files in and out of your device from PC.
you could install other roms, kernel and files using the "install zip" option.
If you want to set up ADB proceed to step 3 (optional, may come in handy and good for other android devices.)
3. Installing ADB on your windows
Download and install Latest JAVA SE Development kit "JDK" and Android SDK.
Follow the steps here on installing ADB, Android Debug Bridge.
3a. SET PATH for ADB: Check if you had set the path to sdk platform tools folder, this is to run adb command from any path. Steps for Windows XP:
Right-click ‘My Computer’ and click ‘Properties’.
In the ‘System Properties’ window, click the ‘Environment Variables’ button on the ‘Advanced’ tab.
Find ‘Path’ in the ‘System variables’ section and double-click it to edit it.
Make sure NOT to delete the existing entry in ‘Variable value’.
Just add the following string to the end of it, including the semi-colons:
;c:\android-sdk-windows\tools;c:\android-sdk-windows\platform-tools;C:\Program Files\Android\android-sdk-windows\platform-tools
Click to expand...
Click to collapse
Start ADB shell to command picopad from your pc:
Make sure Picopad is connected to pc via USB and sdcard is mounted.
From PC, Goto command prompt (Start -> Run type "CMD")
Type "ADB devices" from command prompt ( to see if path is set and picopad is connected, you should see 1 device attached, not more, not less)
C:\Documents and Settings\tish>adb devices
List of devices attached
FM88888888888 device
Click to expand...
Click to collapse
Troubleshooting:
If you can't get the adb command to work, probably you didn't set the path correctly, refer back to SET PATH or go to your adb actual folder to type the command which should be here C:\android-sdk-windows\platform-tools\
3b. Using ADB
At recovery or booted up device, on Pc Type:
adb shell (you will see "$")
Click to expand...
Click to collapse
now access superuser type
su (allow superuser access from Picopad and you will see "#")
Click to expand...
Click to collapse
Here you can copy files using (push/pull), I recommend you google for ADB commands to have a better understanding.
4. More sections to come eg: The space problem on the device, so alternative is partitioning sdcard to install apps as to free up space in device........
You could buy me a beer if you really appreciate my work here.
Updates from Fri the 21th April 2012
Reorganizing error section
Adding missed out steps here and there
Placing direct link for faster downloads
Added 2 older ver. SuperOneclick which works better
Removed CWR 2.5.1.2 details since it's outdated.
Added some details on 5.0.2.6 CWR
Updates from Fri the 13th Jan 2012
Added CWM 5.0.2.6 and soft keys steps.
Added possibility to explore Viewpad 7's dev forum.
Included some wiki info on root and CWR(Clockworkmod Recover)
Added troubleshoot for Set path to android sdk adb folder.
Included ADB set and using step
I first rooted my Picopad using guides from hucqim80, however they are not meant for Picopad and I've gather the info and posted them here.

Original recovery image provided by jax79sg here
This is to recover original recovery and replace clockworkmod recover.
This step is done because you need to send your set for warranty repair probably.
Remember to do a factory reset first before replace with original recover.

tishfire said:
Wonder if anyone had backup their Picopad's original recovery? "orirecovery.img" Accidentally erased mine thinking I had already backup in my pc.
Hope you could put up for me to download thanks .
Click to expand...
Click to collapse
I will upload mine somewhere after i try your steps above.

sure, thanks

axioo picopad.
Hi tishfire , thanks for the guide, i got the same device as yours but when it always stuck at the below lines , can anyone help ? thanks in advance.
[/I]Killing ADB Server...
OK
Starting ADB Server...
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
OK
Waiting for device...
OK
Pushing psneuter...
677 KB/s (585731 bytes in 0.843s)
OK
chmod psneuter...
OK
Running psneuter...[/I]

did u go to cd-rom folder and execute setup.exe before u click superoneclick?

No , I did not run the setup.exe from the cdrom drive cos when i plugin the device it automatically ask me to do the PC syncing. Actually i tried that before but that din work either.
I ran both PC running win7 and winXP, both also stuck at Running psneuter ...

Hi,
I ran into this error which puzzles me greatly.
# flash_image recovery /sdcard/cwrecovery.img
flash_image recovery /sdcard/cwrecovery.img
flash_image: permission denied
Do you know how to resolve this?
Thanks in advance.
Warmest Regards

eagleen said:
Hi tishfire , thanks for the guide, i got the same device as yours but when it always stuck at the below lines , can anyone help ? thanks in advance.
[/I]Killing ADB Server...
OK
Starting ADB Server...
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
OK
Waiting for device...
OK
Pushing psneuter...
677 KB/s (585731 bytes in 0.843s)
OK
chmod psneuter...
OK
Running psneuter...[/I]
Click to expand...
Click to collapse
same with me....anybody can give another tips ?

try to turn on picopad usb first. then try to ru he setup in picopad identified as " cd-rom" try again
Sent via Picopad

is there any custom ROM compatible for this device ?

help
Please help me when i type cp /sdcard/flash_image /system/bin and press enter i got something like this : cp /sdcard/flash_image /system/bin: not found
I'm a wrong.?

can this Stock ROM modified for support with App2sd by Trkton ?

Vuska said:
can this Stock ROM modified for support with App2sd by Trkton ?
Click to expand...
Click to collapse
It supports without any modification in the first place.
Roms, probably the MI700's custom rom will work, get to hucqim80's signature, the link is there.

nhasir said:
Please help me when i type cp /sdcard/flash_image /system/bin and press enter i got something like this : cp /sdcard/flash_image /system/bin: not found
I'm a wrong.?
Click to expand...
Click to collapse
probably ur file is not in that directory for this error message to appear.

eagleen said:
Hi tishfire , thanks for the guide, i got the same device as yours but when it always stuck at the below lines , can anyone help ? thanks in advance.
[/I]Killing ADB Server...
OK
Starting ADB Server...
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
OK
Waiting for device...
OK
Pushing psneuter...
677 KB/s (585731 bytes in 0.843s)
OK
chmod psneuter...
OK
Running psneuter...[/I]
Click to expand...
Click to collapse
Okay, i know your problem... just change the option in superoneclick from psneuter to rageagainstthecage... and then root it...
when the superoneclick start to not responding, just re root it using the same method....
then to enable your superuser, install z4root to your device

I managed to root the picopad and flashed as stated.
When i boot up pressing both power and vol button, i was brought into this FTM mode. And from there i can't do anything...... the screen looks as follows.
Hmm....the cwrecovery didn't get flashed?
SWVer=3.240
MODEL: FM6-0001
HWVer:106
Power on with pressing VOLUME_DOWN keys to leave Auto FTM.
[Resolved]
Try holding both up and down volume buttons instead of just one of them

tishfire said:
Wonder if anyone had backup their Picopad's original recovery? "orirecovery.img" Accidentally erased mine thinking I had already backup in my pc.
Hope you could put up for me to download thanks .
Click to expand...
Click to collapse
This is many months late, here's the stuff if anyone needs it.
http://www.megaupload.com/?d=PKMW1ODU

jax79sg said:
This is many months late, here's the stuff if anyone needs it.
http://www.megaupload.com/?d=PKMW1ODU
Click to expand...
Click to collapse
Im still using my picopad.
Thanks!
Sent from my Nexus S using XDA App

can anyone help me with original backup for the splash and welcome screen axioo pico pad?
my pico pad splash and welcome screen change to viewsonic because i install viewpad 7 ROM in to my pico pad.....
somebody....help me please !!!
thankyou

[How to] Everything I know about the Gooapple 3g and Gt-6

Hi Everyone,
Sorry for the discombobulation of this post, but I have been adding to it non stop.
This thread covers all I have learnt from this model phone;
Root procedures for both Gooapple and iorange GT-6
ADB access (no USB adb so need to use over WiFi), - ADB WORKING NOW!!
Secret reset button location,
Recovery mode,
Download mode,
Drivers,
How to (and not to) theme framework-res.apk with uot kitchen
Flash tool
Change Boot animation
Upgrade External storage.
GPS server change.
Battery Info.
Serial No. Location
Quick access to the Camera
Mayiandjay on the Gooapple 3g on Youtube
Creating an extracted system.img
Dump recovery.img / boot.img
Alternate ROM dumping method (Thanks Dastin1015)
Flash a recovery image (Thanks Dastin1015)
Full Market on the Goo
ROOT;
I have purchased one of these and they are quite easy to get root using Visionary+ for temporary root option to push su and Busy Box, then use Z4root for permanent # works quote well and easy and
Checkout the rooting video here (http://www.youtube.com/user/mayiandjay) for an easier way just using z4root.
ADB OVER Wi-FI;
once you can get adb to recognise it (using terminal emulator on the phone
"setprop service.adb.tcp.port 5555"
then
"stop adbd"
"start adbd"
from there you can use your pc to run
"adb connect *insert IP address here*"
UPDATE: I found how to get ADB access over USB... I just insta;;ed the PdaNetA302.exe file from http://www.alcatel-mobilephones.com/global/content/view/full/25287
and then disconnected when advised to, reconnected when advised to, then BAM!!! working ADB..
I wish I had known about this a week ago...
From here you can have access to all supported adb commands including shell for # access, also for pushing and pulling files from the goo,
UOT KITCHEN; (Be careful dangerous)
I used the "ADB PULL" command to pull "/system/framework/framework-res.apk"
from the device, I then used the UOT Kitchen to modify it to my liking once I got the uot .zip file, I extracted the framework-res.apk file and used "adb push" to overwrite the one inside /system/framework/ dir.
(use a pc to push, not the phone explorer copy paste... Lol I bricked mine by using the file explorer, see the rest of the post for more info....)
RECOVERY MODE, DOWNLOAD MODE and BOOT ANIMATION;
some other usefull info is that you do not have to wait for the phone to run dead if you use the wrong key combo whilst booting ( trying to get into recovery hold home button whilst turning on then 5 seconds after "gooapple" appears let go of home and then press it again) you will get recovery console, where you can change the boot animation to the static apple or the gooapple animation, you can also do a factory reset or clear cache, from here you can also run an "update.zip" file but unfortunatly after i 1/2 bricked mine i stupidly did a factory reset and lost rw on /system (loosing bus box and su) (CRAP!!!) i was using the above mentioned method to use the "uot kitchen" to retheme the framework-res.apk file of the goo, and it was working fine when pushing the framework-res.apk to the phones /system/framework/ dir using a pc, but I got lazy and stupidly did a copy / paste using the phone to return to the original framework-res.apk (i know dumbass right) and then she rebooted to infinate bootlooping (F#@K!!!) I can now get into recovery mode and unfortunatly I cannot get my update.zip that pushes busybox and su etc to sign properly so that I can copy via update.zip the backed up version of framework-res.apk back to the now read only /system/framework dir.... (possible Brick anyone?)
SECRET (hidden) RESET BUTTON;
So... continuing on... to reboot the phone if it locks up and stops responding, you need either the original simtray pin or something like a multimeter probe and stick it down the headphone jack, down there there is a hard reset button, (get a torch and look for yourself if you don't believe me) hope this helps people...
DRIVERS;
Also I downloaded the qualcomm MSM drivers from 4shared and can now connect to the phone cos I noticed that if you boot the phone using the down volume key (i think) with the USB connected you can get nothing come up onscreen on the phone but the PC picks up a new device, the 4shared drivers worked but unfortunately that's where my knowledge stops...
FLASH TOOL;
I downloaded the flash (or google translated "brush") tool from mobileuncle but untill I find someone sharing the rom, or system.img it is usless to me...
UPGRADING EXT. STORAGE;
Something interesting for the rest of you is that the Gooapple 3g ( shows as A4-3G) and the preproduction iOrange Gt-6 (also shows as A4-3G) seem to look the same on the inside, I have both ( but liked the good ol F#@K you Apple, with the apple eating an android boot animation and apple in a android symbol on the back of the device ) I have opened both of them up (use a very small screwdriver on the screws between the speakers and 30pin dock connector on the base, remove these screws and slide the back plate up towards the power button (gentle no to break the retaining nuts on the back plate), from here you can undo the bit of tape and lift the battery up out of the way ( its soldered in so be careful, seeing as its always powered and easyier to short something out ) then next to where the battery sits you will see the back of a micro SD card (this is you external storage) if you get your nail and press on the back of it you will notice it is held by a spring retainer and will pop out a bit, from here press it in half way again with your nail and slip your nail off it, releasing the spring tension, flicking the micro sd card out into the casing (and hopefully not across the room)
you should now find either a 4GB, 8GB, 16GB or possibly a 32GB micro SD card came out depending on the model you chose, if you chose a 4GB or 8GB like i did you can replace it with an inexpensive 16GB Micro SD card put it back together and reboot, This is how I have tried copying my "update.zip" with Busybox and Su files (see above, that wont sign!!! GRRRR) the recovery console recognises the file but says signature authentication fail....
I could sign my "update.zip" for my framework-res.apk file but without Busybox or system RW it is useless.. it passes authentication but without rw on system it is useless....
GPS SERVER CHANGE;
Also, using faster fix off the market (need root) you can change the GPS server for better GPS performance.
BATTERY INFO;
Stamped on the Battery is
PL402874 1000mAh
3.7V 3.7WH
SERIAL NO. LOCATION.
Under the back cover there is a Version (mine is v2.3) and Serial number sticker
QUICK ACCESS TO THE CAMERA
Double click Home on the unlock screen to have quick access to the Camera.
USEFUL YOUTUBE VIDS
Check out mayiandjay on youtube (http://www.youtube.com/user/mayiandjay), he has done videos covering the stuff I am trying to explain, Thanks deepakpitrola333 for pointing this out
CREATING A EXTRACTED SYSTEM AS SYSTEM.IMG
for windows pc,
Go to http://db.tt/GAyvuDE (thanks Dastin1015) download and extract to your sdk/platform-tools folder
Rename mkfs.yaffs2.arm to mkfs.yaffs2 (delete the .arm extension)
open up command prompt (if you don't know how to do this in your current windows environment by now then just give up now)
change dir to the platform-tools dir in the sdk,
TYPE: adb push mkfs.yaffs2 /data/misc/mkfs.yaffs2
then pick up your shinny gooApple device;
open root explorer and navigate to mkfs.yaffs2 select and hold, change to have execute permissions
Back on the PC;
adb shell
su
# cd /data/misc
# ./mkfs.yaffs2 /system /sdcard/system.img
# exit
adb pull /sdcard/system.img ./system.img
I got a 176Mb system.img with "Build ok."
DUMP RECOVERY and BOOT IMAGES
you'll need dump_image from http://db.tt/9EANtEX (Thanks Dastin1015)
copy to your platform-tools folder in your androidsdk dir
do the same as above and push to /data/misc
then as before, change permissions of dump_image in root explorer to have execute. reboot device
Then you can run command prompt
go to your sdk platform-tools directory
run;
adb shell
cd data/misc
./dump_image boot /sdcard/boot.img
./dump_image recovery /sdcard/recovery.img
exit
adb pull /data/misc/boot.img ./boot.img
adb pull /data/misc/recovery.img ./recovery.img
ALTERNATE ROM DUMP METHOD (Thanks Dastin1015);
To do any flashing to the phone you must be rooted.
Rooting:
1) Download z4root and hit the permanent root option: http://db.tt/Bltsa73
2) Once rebooted you will have root.
Dump ROM:
~Prerequisite is that you have root~
{Non ADB method}
1) Download romdump and place it on the root of your SD card: http://db.tt/kXTaCDF
2) Download Terminal Emulator from the Market if you haven't already.
3) Open Terminal Emulator and issue these commands:
Code:
$ su
# cp /sdcard/romdump /system/bin
# chmod 747 /system/bin/romdump
# romdump
4) Now on your SD card under the romdump folder you will find you recovery.img, boot.img and system.tar. Backup these files to your computer for safe keeping.
{ADB method (Must have Android SDK installed)}
1) Open up command prompt and issue these commands:
Code:
C:\Users\Your_Name> cd ..
C:\Users> cd ..
2) Navigate to your installed Android SDK (Mine is under the Program Files (x86) folder):
Code:
C:\> cd Program Files (x86)
C:\Program Files (x86)> cd Android/android-sdk/platform-tools
3) Connect your device to your computer and make sure you have USB Debugging enabled on your phone.
4) Issue this command to verify that your computer recognizes your phone:
Code:
C:\Program Files (x86)\Android\android-sdk\platform-tools> adb devices
5) If you see your phones serial then it is connected.
6) Download romdump and place it in the platform-tools folder: http://db.tt/kXTaCDF
7) Issue these commands:
Code:
C:\Program Files (x86)\Android\android-sdk\platform-tools> adb push romdump /system/bin
C:\Program Files (x86)\Android\android-sdk\platform-tools> adb shell chmod 747 /system/bin/romdump
C:\Program Files (x86)\Android\android-sdk\platform-tools> adb shell
# romdump
you should get the following;
Android ROM dumper v0.82b
(c)2011 Sebastian404
Device : GOOAPPLE 3G QUALCOMM-Android2.2.3-IOSUI-eng.autobuild.20110729.144151
Creating required files... done.
Opening mtd table... done.
Dumping kernel config... done.
Dumping boot partition... done.
Dumping recovery partition... done.
Dumping system partition... done.
Creating Checksums... done.
Cleaning up... done.
8) When done your ROM dump will be in the romdump folder on your SD card.
/sdcard/romdump
boot.img
checksum.md5
config.gz
recovery.img
system.info.gz
system.tar
DONE.
INSTALL CLOCKWORK RECOVERY (orange lantern recovery) ( Tested on my GT-6, that is basicly the same as the gooapple but has the apple symbol on the back, and now my Gooapple 3g,both successfully)
Flashing custom recovery image:
{Non ADB method}
1) Download flash_image and place it on the root of your SD card: http://db.tt/flHRxiG
2) Download recovery.img to the root of your SD card: http://db.tt/uy56zhj
3) Open Terminal Emulator and issue these commands:
Code:
$ su
# cp /sdcard/flash_image /system/bin
# chmod 747 /system/bin/flash_image
# flash_image recovery /sdcard/recovery.img
4) If you see a bunch of successful on your screen then it has flashed properly.
{ADB method}
1) Open up command prompt and issue these commands:
Code:
C:\Users\Your_Name> cd ..
C:\Users> cd ..
2) Navigate to your installed Android SDK (Mine is under the Program Files (x86) folder):
Code:
C:\> cd Program Files (x86)
C:\Program Files (x86)> cd Android/android-sdk/platform-tools
3) Connect your device to your computer and make sure you have USB Debugging enabled on your phone.
4) Issue this command to verify that your computer recognizes your phone:
Code:
C:\Program Files (x86)\Android\android-sdk\platform-tools> adb devices
5) If you see your phones serial then it is connected.
6) Download flash_image and place it in the platform-tools folder: http://db.tt/flHRxiG
7) Download the recovery.img and place it on the root of your SD card: http://db.tt/uy56zhj
8) Issue these commands in command prompt:
Code:
C:\Program Files (x86)\Android\android-sdk\platform-tools> adb push flash_image /system/bin
C:\Program Files (x86)\Android\android-sdk\platform-tools> adb shell chmod 747 /system/bin/flash_image
C:\Program Files (x86)\Android\android-sdk\platform-tools> adb shell
# flash_image recovery /sdcard/recovery.img
9) If you see a bunch of successful on your screen then it has flashed properly.
boot into recovery, hold home whilst powering on, after 5 long seconds, let go of home and then push home again, you will need to put the volume/menu-back toggle to "volume" mode and according to deepakpitrola333, you need to cycle the list 3 times using volume to allow selection.
Video by mayiandjay;
http://www.youtube.com/watch?v=B_dX9Ruoljo
ENABLE FULL MARKET ON THE GOO
Thanks to Smith, we can have the full google market on our Goos
http://forum.xda-developers.com/showthread.php?t=1133702
IF I OR ANYONE ELSE EVER HELPS YOU, PLEASE CLICK THANKS... Its not that hard....
Done.
CHEERS!!! - KEG.

Thanks for info on the gooapple, its good stuff.
Any idea on how to do any of the following:
- restore original recovery screen
- get a clockworkmod recovery image to work
- do a nandroid backup
i have managed to get the applestyle home apks and the keyboard and stuff and so want to install another rom. I flashed a random clockworkmod image but now i dont get any recovery screen at all, its gets stuck on apple every time on every button combo/method.
if its not too much to ask, could you check if you can run fpse the psx emulator on your gooapple, it crashes to home straight after loading a game even tho i have a bios. psx4droid works but is choppy, similarly specd phones like the wildfire s and legend can play fpse games like ff7 very well.

Gooapple GPS
Do you now how to acivate the GPS on the gooapple.
Have this phone a GPS chip like SiRF III chip?
Is it possible to use it with navigation software?

Did you purchase it? If you did that, please, send me link to rom dump after you dump it or you know already existing link?
Sent from my IDEOS S7 Slim using XDA App

this phone has a sirf III and installing a gps program makes the gps work.
i cant dump the rom without getting a clockworkmod recovery image that works for this phone, unless you know of a way jon2555.

Hey guys, the best way I found to toggle gps on (because it does not show up in networks) is by installing go launcher so you get a shortcut to it in your apps, the press home and set applestyle as default again, then go through your drawer and select the go launcher shortcut, from there add the power control widget, from there you can toggle gps...

Also I have been nagging the people at the gooapple factoryand they advised they may add a downloadable firmware upgrade soon...., fingers crossed as mine is currenly half bricked, I got access to the fastboot by downloading the microsoft mobile drivers update, that lets fastboot recognise it when you reset with the vol down button, but need to read up on how to use it....
I had a quick readup on fastboot commands, and I have written an update script (The one that I cant sign), and I'm going to try to run it with fastboot as my limited and unexperienced understandung is that through fastboot you dont need signed updates...., unfortunatly I left my goo at work on wednesday and I was in Sydney all day today, so i wont be able to try it out untill I return to work in freezing Canberra tomorrow... Fingers crossed, and if I can successfully get it working again I will try to find a way to dump the partitions and make an update.zip that rewrites all of /system (if possible), so next time i kill it, I may have a better chance recovering from my mistakes (or pure lazyness....)

jon2555, no rom yet, but Hat007 did previously do an app dump of all the apps on gooapple 3g here,
http://forum.xda-developers.com/showthread.php?t=1245655
(thanks hat007)
and as deepakpitrola333 said, until somebody can put a working clockwork on it, we are out of luck regarding nandroid backups.... and my goo is currently bricked so i cant do much with it, and i gave my gt-6 to my daughter already, so no chance of getting that back......

Gooapple Firmware ROM Update
Hi All,
I'm New to this. Is there going to be a ROM or Firmware Update? if so how is it going to be done? Which Website??
I've bought mine from Android-Sale.
Has anyone else bought there's from Android Sale?
Also Is there a FIX to Make the Unlock Slider Back to English without the Stupid Chinese Symbol TXT??
Also Is anyone having Trouble with there Built-In GPS?? I cant get mine to Work??
I Look Forward to your Comments.
Cheers.....

hey spookie,
kegatron has said to toggle the gps from go launcher, which enables an android style interface with power options for bluetooth, gps, wifi etc by widget or otherwise. I assume you can do this with the stock froyo launcher too.
Home key can select the launcher after a third is installed.
I got mine from fastcardtech as they gave a discount over android sale, however it will be gooapple themselves releasing the update and or rom in the future.
With so many units sold, there is gonna be stuff up soon.
If someone knows how to make thier own clockworkmod recovery, the rom can be uploaded by anyone with the phone. I have no clue who to ask to do this tho.
The chinese in the lock screen is not something i know how to change but as i said a stock froyo launcher and lock screen can be used instead. Helps with the long icon name problem too.
If its not too much to ask can you check if fpse, the psx emulator, works on your phone. It crashes straight away on mine but all psx4droid versions work but as it is known, psx4droid is considerably slower, like 10-20 fps slower making final fantasy games run 50fps max and 35-40 normally which is too choppy.
I hope what i have said helps, gps isnt on all the time so try to toggle it like keg said and if you know anyone who can write custom recovery images, get them over here
i also assume you have rooted to get rid of all chinese from system icons/folders

Hey Spookie,
With the GPS, I was still using the applestyle launcher but one of the good things about go launcher is the fact that it has a app link in your app drawer, meaning you can select the applestyle launcher as the default and still have access to go launcher without too much hassle (just select it in the apps on your home screen)
So with that said I assume you have root?, if not... get it... Lols..
from there you can get rid of the standard Chinese crud that I cant read like baidu input or whatever its called, QQ (whatever that is...) etc. using Titanium backup (CAREFUL FOR WHAT YOU UNINSTALL, and batch backup everything first!!!), I'l put up a list of what can be uninstalled safely once I get mine working again. and you can fix the server your GPS is looking for by using FasterFix from teh market (you need root for this)
And the gooapple webpage is quite easy to find.... I just googled gooapple and funnily enough the webpage's name wasn't too cryptic (its www.googapple.com lol) just use the google chrome browser to automaticly translate the Chinese and for most of the bad translations you can still work it out..
Hope this helps...
BTW, I'm looking into rewriting my update.zip file for my framework-res.apk file as the scripting is different using fastboot and I need to read up on it.. give me time
I need to work out what needs to be in the android-info.txt and android-product.txt files....

Hi Guys,
Thanks for all you Help & input.. However I'm Very Confused and Lost?? Yes I've installed Z4Root.
But Now That I've installed this App. How can I BACKUP the Whole ROM as it is before I Start to Uninstall all thoses Chinese APPs etc??
Also What Input Keyboard do I install? Which one is the Chinese Keyboard??
I'm Wanting to keep the Stlye of the Phone as it is when I bought it but wanting to Take Out the Chinese Junk, and Install just want I want in English.
As for the GPS, is there a Way to Keep it always Switch on From First turning on the Phone??
I do hope you dont think I'm a Stupid Person??
I dont want to Brick or Destroy this Phone?? Just want the Chinese Junk Out and GPS & the Unlock Slider Fixed?? Do hope they Bring out Firmware or ROM Update? I'm picking it's going to be on here once it's Relesed??
Look Forward to your Comments.
Regards
Spookie...

Gooapple Camera & YouTube
Hi Again,
I was meant to also ask in my Last Post
Can anyone if Possible post a Photo on here taken Directly off there gooapple device? Ans is it a True 3.2mb Camera? And Also is the Front Camera 1.3mb?? I'd be glad to have a look and you image....
I cant get youtube to work with the Youtube App? I've tried all sorts of Differnt Apps (apk files), and still NO Luck with youtube??
Any Thought's Or Comments??
Thanks...
SpookieNZL

Hey Spookie,
Sorry champ, if I misdirected you, what I ment by batch backup all the apps first was to do with "Titanium Backup" from the market, it requires root access
to test for correct root access, you should get # when you type su in a terminal emulator.
try this once you have it installed,
Download the Iphone keyboard from the market, the go to settings, keyboard, and enable the iphone keyboard (tick box) then, find any text box and press and hold the box untill "input method" comes up select iphone keyboard
Once you have the iphone keyboard working, you can then delete the baidu (or whatever it was called) keyboard, by opening Titanium backup, accept super user access, then go to "backup / Restore" then press the menu key (vol up) then select "Batch" then select "backup all user apps +system data", then once completed, you can then go back to "backup /restore" and find Baidu input and select it, and then "uninstall"
Congrats you have now deleted the Baidu input,
I would recommend NOT uninstalling anything that you don't know if it is crucial or not, as if you delete the wrong thing you can get major "Force close" issues and make the phone 100% unusable until a ROM has been released to re-write the partition and start again...
With the Camera, I will post a heap of photos up when I get mine working again, I have taken lots of photos of pulling it apart and upgrading storage etc. I am in the progress of putting all the info from this post into a full guide with photos of step by step how to do everything that I know of, as I can't find anything from anyone else posted on the net regarding most of the things i have covered, I might just step up to the plate and do it
With Youtube, I installed the tubemate app from market, worked fine for me.., try it an let me know
Hope this helps!!!
Also, for those who didn't know, when you have the slide to unlock screen, if you double click home you will get a camera icon pop up (on an Iphone / ipod this is to access the music menu) that way you can get quick access to the camera to take a photo

hey keg why are you telling him to uninstall baidu input, on its last setting it is a perfect iphone input keyboard completely in english, the one on the app market is not good looking or accurate.
also, on youtube this guy, mayiandjay, has good videos on some of the stuff your trying to explain so maybe skip this to save time.
lastly i hope you get your phone back to working, as i have the phone working and sort know what im doin, feel free to ask for anything from it.
spookie, ill get some daylight pics up in the morning, at night the camera looks more grainy but is still good.

Hi deepakpitrola333,
Sorry I never really gave the Baidu input a real go, I found it slow unresponsive, and sometimes would revert back to converting whatever I was trying to write into Chinese, so it got the ass, I did get swype working on it, but I'm used to my Galaxy S and didn't find it that good on this device.
I suppose my guide to deleting the Baidu input was reversable if you did it step by step, you can go into titanium backup, go to backup / resore, and go right to the bottom, select baidu input that should have a line through it, and select restore.
BAM!!! Bauidu is back, though you will have to enable it again through the keyboard s option in settings, then press and hold a text box and select it again....
Sorry for the confusion.

yea it took me a while to set it to how i like, iphone style full english with predictive, wild guesses from the options list when holding down the circle key.
it is faster than the 4-5 keyboards ive used and looks the best in caps with no numbers to ruin the look.
it wont help you keg because yours is unfortunately bricked but spookie, on baidu after getting the keyboard up (press home a few times), hold the circle (world?) key, then select last, (keyboard will close) then hold bottom left key after getting it back up then first option, then second to last for predictive or last for non predictive.

Got the Goo Going again!!!
WOOOO!!! I'm soo happy
here's how I did it, (and I will add this to the first post)
When my device was bootlooping (the gooapple animation was playing over and over) I connected it to my computer, noticed that once again I got the unknown devices (4x qualcomm HSUSB interface) pop upagain and after giving up trying to find the Qualcomm HSUSB Driver prviously I decided to go on the hunt as this was close to my last resort before giving up for the day, well guess what!! I found it!!
I downloaded a file called PdaNetA302.exe and it installed the correct drivers for me!!! from there I could finally see the device in the Android Debug Bridge (especially whilst it was was booting!!) from there I could push the framework-res.apk into the /system/framework/ dir on the goo!!! WOO HOO!!
I'l play with it for a while and start ripping everything off it tonight, see what I can do about making a backup of some sort.... or if anything a listing of all dirs and files in each partition.
Thanks everyone who is reading this for your support during these "goo-less" times

Hi! I am the youtube member "mayiandjay" that has been posting some videos on how to work around with the gooapple 3g.
Recently I tried flashing clockworkmod recovery but now I get stuck on the "gooapple" logo.
How can I restore the original recovery Image or get one that works for this unit. ANY HELP WILL BE GREATLY APPRECIATED!! THANKS IN ADVANCE.

Hi! I am the youtube member "mayiandjay" that has been posting some videos on how to work around with the gooapple 3g.
Recently I tried flashing clockworkmod recovery but now I get stuck on the "gooapple" logo.
How can I restore the original recovery Image or get one that works for this unit. ANY HELP WILL BE GREATLY APPRECIATED!! THANKS IN ADVANCE.

Full root for A700 and A701 tablets

WARNING. THIS is ONLY for tablets running ICS. If you are running Jelly Bean, You May Brick your device!!
Again, this is for ICS ONLY!
Running this root on a Jelly Bean OS can cause your tablet to stop functioning as it is designed for ICS only. If you have a Jelly Bean Operating system, then please use Vorbeth's or Moscow Desire's Easy Root Package located in the Development Forum. If you do not know which OS you currently have, then you should ask questions before rooting.
Method 1. Universal for A700 and A701 Tablet
1. Enable adb mode: Settings -> Developer options -> USB debugging - check it point.
2. Unlock your bootloader for fastboot, follow here. Then reboot a tablet.
3. Download arhive. Unpack it to any place.
4. Open the directory with the unpacked archive. Execute file:
for windows with the rights of administrator:
Code:
runit.bat
Your firmware is now rooted.
5. At first it is necessary to start the Superuser program, at least 1 time after receiving root. And only then programs that require root access.
ATTENTION!
Don't install Busybox! It is already installed and established! If you reinstall it, some programs will become unable to access root permissions!
------------------------------------------------------------------------------------------------------
Method 2. With the patched kernel from the A700 tablet
For ICS A700 firmware only!
1. Enable adb mode: Settings -> Developer options -> USB debugging - check it point.
2. Unlock your bootloader for fastboot, follow here. Then reboot a tablet.
3. Download this arhive. Unpack it to any place.
4. Open the directory with the unpacked archive. Execute file:
for windows with the rights of administrator:
Code:
flash-ICS-patchedBoot.bat
Your boot.img is now patched and firmware is now rooted.
5. At first it is necessary to start the Superuser program, at least 1 time after receiving root. And only then programs that require root access.
6. Now you will have to install the following programs:
BusyBox
Titanium Backup
7. Run BusyBox and go through the install steps. During this SU should ask permission to give BB root access, if it does, it worked!
------------------------------------------------------------------------------------------------------
Method 3. From CWM recovery for A700 and A701 Tablet - Not available due to problems in the work of CWM recovery!
1. At the tablet must be installed CWM recovery.
2. Download arhive ICS_Rooting_recovery.zip. Put it on SD-card. Insert the SD-card in the tablet.
3. Run CWM recovery on the tablet and flash ICS_Rooting_recovery.zip.
Your firmware is now rooted.
4. Now you will have to install the following programs:
SuperUser
Titanium Backup
At first it is necessary to start the Superuser program, at least 1 time after receiving root. And only then programs that require root access.
ATTENTION!
Don't install Busybox! It is already installed and established! If you reinstall it, some programs will become unable to access root permissions!
------------------------------------------------------------------------------------------------------
Method 1, in contrast to method 2, does not affect the core of the system. This makes it possible to receive future firmware update. But only if you do not forget to make backups before making changes to the system and restore it before upgrading.
PS: I tried to make a method 1 as safe as possible. But I have not had a chance to test it completely. So if it does not work, be sure to let me know in this thread and I modified it.

great work ! Thank you for this :good:
BTW the the script is called "flashpboot.bat" and not "flash-ICS-patchedBoot.bat" in the archive.

Really great thanks for it.
Just a question, can it be unrooted/undone by flashing 028-stock rom?
Gesendet von meinem A700 mit Tapatalk 2

KruSan said:
Really great thanks for it.
Just a question, can it be unrooted/undone by flashing 028-stock rom?
Gesendet von meinem A700 mit Tapatalk 2
Click to expand...
Click to collapse
yes

the patch with Acer_AV043_A700_1.028.00_EMEA_FR doesn’t work after flashing the patched boot the tablet doesn’t boot it stuck at Acer logo

moom999 said:
the patch with Acer_AV043_A700_1.028.00_EMEA_FR doesn’t work after flashing the patched boot the tablet doesn’t boot it stuck at Acer logo
Click to expand...
Click to collapse
same problem here

moom999 said:
the patch with Acer_AV043_A700_1.028.00_EMEA_FR doesn’t work after flashing the patched boot the tablet doesn’t boot it stuck at Acer logo
Click to expand...
Click to collapse
Rename Acer_AV043_A700_1.028.00_EMEA_FR to update.zip and put it in an external sd card.
There's a startup mode that installs it automatically, you have to press the left volume+power buttons at startup if I remember well.

alx5962 said:
Rename Acer_AV043_A700_1.028.00_EMEA_FR to update.zip and put it in an external sd card.
There's a startup mode that installs it automatically, you have to press the left volume+power buttons at startup if I remember well.
Click to expand...
Click to collapse
you missunderstand, they mean, when you have 1.028 you cant flash the patched bootloader because they stuck onn boot screen

No problem to flash again Acer_AV043_A700_1.028.00_EMEA_FR or Acer_AV043_A700_1.025.00_EMEA_CUS1
The problem the patch doesn’t work with any of this two rom

moom999 said:
No problem to flash again Acer_AV043_A700_1.028.00_EMEA_FR or Acer_AV043_A700_1.025.00_EMEA_CUS1
The problem the patch doesn’t work with any of this two rom
Click to expand...
Click to collapse
The size of the patched bootloader seems wrong, I guess that's why it's faulty.

OK, so how do we fix this ??
Edit, reflashed with update.zip, so all OK, phew !

Cannot reproduce with Acer_AV043_A700_1.028.00_EMEA_FR !
Just stays at Acer logo with unlocked bootloader and forces me to re-install as update.zip which leaves me without root.

Which Firmware is working ?
Has anybody allready tested with which firmware this method is working and with which not ??

Be careful, same issue on NORMAL french firmware, not the crappy totally unknown one everybody seems to like, so i guess that's it : this patch STUCK YOUR TABLET ON ANY KNOWN FIRMWARE THIS FAR

Okay, so i just tried to push insert the superuser.apk into the Acer_AV043_A700_1.028.00_EMEA_FR file and flashing this, but as i was expecting, it didn't work out... it didn't even install.
edit: i can confirm, that it does neither work with the Acer_AV043_A700_1.028.00_EMEA_FR, nor the Acer_AV043_A700_1.025.00_EMEA_CUS1 !
so, i guess we have to wait for ZeroNull to come up with another way to get this to work.

Flashboot.bat not responding
I unlock my bootloader with Blackthund3r's A510 Bootloader Unlocker v1.0.0 and go the "unlocked" status. Rebooted the tablet, went into the patched-boot folder and ran as administrator "flashboot.bat". The screen displayed a bunch of what looks like gibberish and when I pressed the Enter key, the screen went to :
"Flashing patched boot.img
<waiting for device>
Then the process just sits there and doesn't go any further. Am I missing something in what I am doing?
---------- Post added at 02:27 PM ---------- Previous post was at 02:18 PM ----------
I used Root Checker Pro to verify root and here is what the app displayed:
"Root Access is not properly configured or was not granted.
Superuser Application Status:
Superuser application - version 3.0.7 installed!
(I had downloaded and installed this from the Market after the first attempt failed)
System File Properties for Root Access:
Standard Location
Check Command: ls -l /system/bin/su:
Result: /system/bin/su: No such file or directory
Analysis: File /system/bin/su does not exist.
Standard Location
Check Command: ls -l /system/xbin/su:
Result: /system/xbin/su: No such file or directory
Analysis: File /system/xbin/su does not exist.
Alternative Location
Check Command: ls -l /sbin/su:
Result: /sbin/su: Permission denied
Analysis: File system permissions restricted and denied access.
Alternative Location
Check Command: ls -l /system/xbin/sudo:
Result: /system/xbin/sudo: No such file or directory
Analysis: File /system/xbin/sudo does not exist.
Root User ID and Group ID Status:
SU binary not found or not operating properly
System Environment PATH: /sbin /vendor/bin /system/sbin /system/bin /system/xbin
ADB Shell Default User:
ADB shell setting for standard access, stored in default.prop, is configured as: shell (non root) user - ro.secure=1"
Anybody got any ideas on what to do next?
Thanks!

You have to reboot into bootloader for the script to work.
But if you had read the comments above, you might have seen, that the described method does not yet work and several people state, that after flashing the Boot.img the device is stuck in boot.
Gesendet von meinem A700 mit Tapatalk 2

Just to be clear : This method specific to A700 does not work at all yet BUT this WORKS PERFECTLY with the A701 patched rom ZeroNull released at the same time
check this post for the a701 patched rom, you don't need to put it on sdcard it includes BAT files to flash it all from bootlader
http://forum.xda-developers.com/showpost.php?p=27742776&postcount=39

Hello jpearn or doanb555,
With which release of the "update.zip" you can restore your Iconia Tab A700 ?
thx

spoque said:
Hello jpearn or doanb555,
With which release of the "update.zip" you can restore your Iconia Tab A700 ?
thx
Click to expand...
Click to collapse
i'm not jpearn or doanb555 but what kind of question is that ? you got only two roms, both are working. what's your point ?

[ROOT] $99 Walmart Nextbook 8 (NX008HD8G)

The Nextbook 8 (NX008HD8G) is a $99 tablet available from Walmart. It sports a AMLogic AML8726-MX SoC (1.5Ghz dualcore Cortex-A9 w/400mhz dualcore Malli400 GPU), 1 Gb of DDR3 RAM, 8" display, and 8Gb internal storage. Its a nice little budget tablet for those who don't need a Nexus 7 or greater performance rated tablet. Not too long ago I discovered how to root it and apparently I'm the first to do it as far as I can tell. Now here's how.
What you will need is Bin4ary's One Touch Root App. This app will get you only partial root via the ADB Shell. My guess is the ADB exploit he uses does work to get basic root access for ADB, but some incompatibility prevents proper installation of su & SuperUser.apk. What we're going to do is finish the job manually.
First run Bin4ary's app and use the Normal Method. Be sure to ignore all errors. After your tablet reboots move su and Superuser.apk from Bin4ry's app folder to the root of the Internal SDCard. Next you will need ADB. If you don't have it you can get it either from Bin4ary's app folder you found su & superuser.apk in or you can install the Android SDK. At the command prompt enter the following:
Code:
adb shell
su
At this point you should see a # sign indicating root privileges. If you do enter the following commands.
Code:
mv /system/xbin/su /system/xbin/osu
cp /sdcard/su /system/xbin
chmod 6755 /system/xbin/su
The use Astro or your favorite file manager to navigate to /sdcard and install SuperUser.apk then reboot your tablet. From here on you should have full root on your tablet. Credit should definitely goto Bin4ry for his work on his One Touch Root App for getting us half way there.

Confirmed Working
Confirmed. Works as described.
Nice work!

Thank you for this information, works excellent.

Ron Overdrive said:
The Nextbook 8 (NX008HD8G) is a $99 tablet available from Walmart. It sports a AMLogic AML8726-MX SoC (1.5Ghz dualcore Cortex-A9 w/400mhz dualcore Malli400 GPU), 1 Gb of DDR3 RAM, 8" display, and 8Gb internal storage. Its a nice little budget tablet for those who don't need a Nexus 7 or greater performance rated tablet. Not too long ago I discovered how to root it and apparently I'm the first to do it as far as I can tell. Now here's how.
What you will need is Bin4ary's One Touch Root App. This app will get you only partial root via the ADB Shell. My guess is the ADB exploit he uses does work to get basic root access for ADB, but some incompatibility prevents proper installation of su & SuperUser.apk. What we're going to do is finish the job manually.
First run Bin4ary's app and use the Normal Method. Be sure to ignore all errors. After your tablet reboots move su and Superuser.apk from Bin4ry's app folder to the root of the Internal SDCard. Next you will need ADB. If you don't have it you can get it either from Bin4ary's app folder you found su & superuser.apk in or you can install the Android SDK. At the command prompt enter the following:
Code:
adb shell
su
At this point you should see a # sign indicating root privileges. If you do enter the following commands.
Code:
mv /system/xbin/su /system/xbin/osu
cp /sdcard/su /system/xbin
chmod 6755 /system/xbin/su
The use Astro or your favorite file manager to navigate to /sdcard and install SuperUser.apk then reboot your tablet. From here on you should have full root on your tablet. Credit should definitely goto Bin4ry for his work on his One Touch Root App for getting us half way there.
Click to expand...
Click to collapse
Did NOT work for me.
1-On first attempt, got pound sign....tried to push code resulting in cant find SD
2-On second attempts, would not let me be superuser su
3-Did a factory reset....same results as (2)
Im stomped!....please help

Amlogic Next8HD8G (NX008HD8G) Modified Recovery - Stock Rom - Root & Gapps
Modified recovery, stock rom, flashable root and flashable Gapps here: http://www.freaktab.com/showthread.php?7010-Amlogic-Next8HD8G-%28NX008HD8G%29-Modified-Recovery-Stock-Rom-amp-Flashable-Root
ShaunMT

Confirmed as well..
Ty... no fusses at all..

zenkillizen said:
Ty... no fusses at all..
Click to expand...
Click to collapse
I need someone to be more clear on rooting this device because I already bricked one using the method from tab freaks instructions aren't that clear and I don't want to brick another one ! Please thanks

andrew09 said:
I need someone to be more clear on rooting this device because I already bricked one using the method from tab freaks instructions aren't that clear and I don't want to brick another one ! Please thanks
Click to expand...
Click to collapse
this guide is like the clearest root guide I've seen Just sit down and read it, take your time Rooting my seem hard at first, but you catch on

Aiko0923 said:
this guide is like the clearest root guide I've seen Just sit down and read it, take your time Rooting my seem hard at first, but you catch on
Click to expand...
Click to collapse
Parts are missing from the guide like how to install the adb drivers the computer needs to recognise the tablet first before u try and root it I have read through it and I've already bricked one also I noticed if you go to recovery on this tablet it erases the system and factory reset doesn't fix anything there's no factory ROMs or anything to fix it if it messes up. If someone can't a sure me that the method is correct I'll do it I'll try it.

Does this method work on the newer models say model number starting with YFG12 and up?

I bought this today.
I am having problems here:
I did what you said to do:
Normal Mode enabled!
Pushing busybox....
4806 KB/s (1165484 bytes in 0.236s)
Pushing su binary ....
7134 KB/s (104576 bytes in 0.014s)
Pushing Superuser app
6792 KB/s (2139595 bytes in 0.307s)
Making busybox runable ...
Now unlock your device and confirm the restore operation.
Please look at your device and click RESTORE!
If all is successful I will tell you, if not this shell will run forever.
Running ...
Successful, going to reboot your device in 10 seconds!
RunMe.sh: line 222: wait: pid 10 is not a child of this shell
Waiting for device to show up again....
RunMe.sh: line 225: wait: pid 10 is not a child of this shell
Going to copy files to it's place
mount: permission denied (are you root?)
You can close all open command-prompts now!
After reboot all is done! Have fun!
Bin4ry
---
And then I copied the files su and the .apk to /sdcard
Then I try to run su, and it says:
su
/system/bin/sh: su: not found
so I do
[email protected]:/sdcard $ ./su
/system/bin/sh: ./su: can't execute: Permission denied
---
Other times, it just does this:
Now unlock your device and confirm the restore operation.
Please look at your device and click RESTORE!
If all is successful I will tell you, if not this shell will run forever.
Running ...
and it runs forever
what do I do?

http://www.cydiaimpactor.com/
Worked for me.

YES! use cydia impactor
H0wdy said:
http://www.cydiaimpactor.com/
Worked for me.
Click to expand...
Click to collapse
Yes, I used it also. worked for me too (my serial for the tablet is YF07... in case there is a problem with the newer versions)
Thanks, H0wdy
Steps to do it:
Download Cydia Impactor
Turn on USB debug in settings-> Developer options
Plug in tablet into PC (I used a 32 bit Windows 8.1)
Wait a while... a long while for me... for windows to download drivers, disconnect tablet, wait a few seconds, then reconnect.
you should see in the device manager (on the top) android phone and underneath Android Composite ADB interface
Unzip Cydia, run impactor.exe and just choose start for # drop SuperSU su to /system/xbin/su
Wait a bit, then you're done. (no reboot or anything else necessary).
Install supersu (or I guess any other superuser app) from the android market. It will tell you that you can update the su binary... your choice, I updated without a problem.
I had supersu installed beforehand, but I guess it has nothing to do with it, it wasn't working anyway)
Ranting, but maybe someone has this issue also:
One ( -- BIG --) problem I had was getting the connection between the tablet and my computer, and Not because I can't plug-in a cable
the tablet said it was connected, but on the computer, nothing showed up in device manager and the list of devices kept refreshing.
The PC was beep-ing just like it found a device. the device list would refresh once or twice, then again beep, all this till the end of my patience.
At first I thought it was the USB 3.0 port, then the cable, then the ESXi USB redirection (my desktop is actually a VM), then the windows version, then the architecture,
Then I switched to a laptop, nothing.. same story.
I can BET it's Sony's F***ed up drivers
So, I used a clean system (no other adb or phone drivers installed) and worked as a charm
I think I hat this much trouble because I had a lot of other drivers (for sony, samsung, universal adb, etc etc.)
So on the computer I had all this stuff installed, it looked like the tablet was connected, then disconnected in the space of 10-15 seconds, then repeat forever.
If this happens to you, use a clean windows.