Related
Hello everyone. It has been a year since i bought my Captivate and i just put my hands on this awesome device (Infuse 4G).
I feel a little retarded as i completely forgot who i donated to on this forum for helping me to unlock my captivate when there was no soft for it in the market yet. I would like to thank you again whoever it was.
Anyway, I would like to ask you to help me to get rid of At&T crapware and get a nice clean fast rom. I will also need instruction for a total retard. Flashing a phone is not an everyday business for me.
Thanks
4biddenskill said:
Hello everyone. It has been a year since i bought my Captivate and i just put my hands on this awesome device (Infuse 4G).
I feel a little retarded as i completely forgot who i donated to on this forum for helping me to unlock my captivate when there was no soft for it in the market yet. I would like to thank you again whoever it was.
Anyway, I would like to ask you to help me to get rid of At&T crapware and get a nice clean fast rom. I will also need instruction for a total retard. Flashing a phone is not an everyday business for me.
Thanks
Click to expand...
Click to collapse
Super One Click for root and Infused for ROM.
http://forum.xda-developers.com/showthread.php?t=1105413
Also, this belongs in the General Forum.
* Download and extract the .zip = done
stuck at:
* Use a terminal emulator or ADB Shell and mount system as read/write.
unfortunately this is where i have no idea what terminal emulator is and how to use it, nor what ADB shell is.
Download root explorer, go into your base dir and click the "mount as r/w" button at the top
4biddenskill said:
* Download and extract the .zip = done
stuck at:
* Use a terminal emulator or ADB Shell and mount system as read/write.
unfortunately this is where i have no idea what terminal emulator is and how to use it, nor what ADB shell is.
Click to expand...
Click to collapse
Which zip have you downloaded and extracted?
Have you read any instructions that are all over this site and many others?
There are literally video tutorials that go step by step from stock out of the box, to rooted and installing a ROM.
Search is your friend. Your best bet is to do some reading before you attempt to install a custom ROM. It's actually quite simple to do, hell I have upgraded my ROM while driving from the hanger at work over to the airport terminal.
However, if you don't know what you are doing, and aren't familiar with the concepts, you can and most likely will end up with a nice shiny brick. (soft brick most likely)
So, find the INFUSED rom thread and start reading and looking at the tutorials he has posted before you take another step. Then, and only then, if you still have questions, people will be very happy to help you out.
Also, as for unlock - if you read through the various threads on this forum, there are two methods covered for obtaining the SIM unlock code for our phones. One requires your phone to be rooted already, one is a script that roots the phone, extracts the code, and then optionally undoes the rooting.
Thanks a lot guys. I really should slow down and read stuff properly. Will let u know how im doing. Thanks again for being there.
Sent from my SAMSUNG-SGH-I997 using XDA App
4biddenskill said:
Thanks a lot guys. I really should slow down and read stuff properly. Will let u know how im doing. Thanks again for being there.
Sent from my SAMSUNG-SGH-I997 using XDA App
Click to expand...
Click to collapse
Good insight.
Closed.
Greetings,
I am looking for an easy to understand method of root.
I have read the new user thread. I am afraid with this so called "easy" method for beginners, there is a lot of jargon used that I simply don't understand.
For example in the thread for easy root, I am lost at step #2 where I am instructed to:
"Note that adb is required.
Push misc.img, busybox, and psnueter using the following commands:"
I don't know what adb is let alone how to push misc.img, busybox and psnueter.
Can someone please point me to the instructions for absolute morons to this process like me.
Thanks in advance.
priapos said:
Greetings,
I am looking for an easy to understand method of root.
I have read the new user thread. I am afraid with this so called "easy" method for beginners, there is a lot of jargon used that I simply don't understand.
For example in the thread for easy root, I am lost at step #2 where I am instructed to:
"Note that adb is required.
Push misc.img, busybox, and psnueter using the following commands:"
I don't know what adb is let alone how to push misc.img, busybox and psnueter.
Can someone please point me to the instructions for absolute morons to this process like me.
Thanks in advance.
Click to expand...
Click to collapse
Android adb http://developer.android.com/guide/developing/tools/adb.html
which is in the sdk http://developer.android.com/sdk/index.html
You dont really need to know what the other tools are listed do, you just need to do what it says with them and the tools are linked in the thread you're reading to download I assume. If they aren't, then read through the manual method that is stickied in the developer's forum. A link for the tools (misc.img, busybox, and psnueter) can be found there.
I was a little nervous at first myself. I read over the directions several times and then found some information on how to get adb installed and working. Once I got that step understood the actual rooting process was super easy. You can cut and paste all the commands to ensure you don't typo. Just make sure to validate your checksums to save any potential headaches. My first attempt at it took about 20 minutes and I had absolutely ZERO issues.
It is well worth your time and effort. It is also far better to use this method than the easy root 1 steps as you will gain a slightly better understanding of how your phone works and what steps you can take when you inevitably mess something up flashing ROMS, mods and radios
Thanks for the quick reply.
I am not nervous, I just don't understand what any of this is.
I don't know what adb is or how to use it.
I don't know what copy and pasting the commands means.
I certainly don't know what "validate checksums" are.
I realize I am coming across as a comlete shmo, but explaining how to do this with more computer jargon doesn't clarify the process.
I really need instructions for dooshbags like me.
Thanks in advance.
There are also videos on YouTube showing JCases method and adb setup. I would link but I'm on my phone but it shouldn't be to hard to find.
Sent from my ADR6400L using XDA App
priapos said:
Thanks for the quick reply.
I am not nervous, I just don't understand what any of this is.
I don't know what adb is or how to use it.
I don't know what copy and pasting the commands means.
I certainly don't know what "validate checksums" are.
I realize I am coming across as a comlete shmo, but explaining how to do this with more computer jargon doesn't clarify the process.
I really need instructions for dooshbags like me.
Thanks in advance.
Click to expand...
Click to collapse
reading through this might help http://forum.xda-developers.com/showthread.php?t=1143188
There is no "easy", reliable way to root sans ADB and command lines. You will need to know this stuff before you try to root. You're going to need ADB in any event. If learning it isn't knowledge you desire, you shouldn't root your phone. For terms, you should refer to the dictionary stickied at the top of the forum. The best way to learn is to get the Android SDK, set it up, make sure your drivers are there, then play with ADB. Do simply stuff like check your serial number, the md5 of files on your SDcard, and harmless stuff like that. If you've got any questions along the way, feel free to PM me any time. I'm here often. And I'm usually faster than hunting through forums or the internet.
priapos said:
Greetings,
I am looking for an easy to understand method of root.
I have read the new user thread. I am afraid with this so called "easy" method for beginners, there is a lot of jargon used that I simply don't understand.
For example in the thread for easy root, I am lost at step #2 where I am instructed to:
"Note that adb is required.
Push misc.img, busybox, and psnueter using the following commands:"
I don't know what adb is let alone how to push misc.img, busybox and psnueter.
Can someone please point me to the instructions for absolute morons to this process like me.
Thanks in advance.
Click to expand...
Click to collapse
From what i think if u dont want the adb command line ****s you should try the software named "z4root". It automatically roots your phone.
Worked for me. And i think itz the easiest method available.
After installing the apk.
Open the application, click PERMANENT ROOT,
Then dnt let your phone sleep or lock itself, wait for about 10 minutes,
After the process reboot ypur phone.
Voila, you are rooted ..
Am new to the forums. please guide me..
Thanks and sorry for my poor english. Hope you like this.
Cheers!
__________________________________________________________
MODEL : LG Optimus GT540 (Rooted)
MOD : SwiftDroid v2.0 M6 (Based on CyanogenMod v7.1 RC0)
KERNEL : 2.6.29 (VirtualBox #309)
BUILD : GRJ22
RECOVERY : ClockworkMod Recovery v4.0
___________________________________________________________
BusyBox v1.19
SuperUser v2.3
SetCPU v2.2
I would not recommend "easy" root methods, since there is greater room for error. Understanding ADB will help you in the long run
MeAt.HoOk said:
From what i think if u dont want the adb command line ****s you should try the software named "z4root". It automatically roots your phone.
Worked for me. And i think itz the easiest method available.
After installing the apk.
Open the application, click PERMANENT ROOT,
Then dnt let your phone sleep or lock itself, wait for about 10 minutes,
After the process reboot ypur phone.
Voila, you are rooted ..
Am new to the forums. please guide me..
Thanks and sorry for my poor english. Hope you like this.
Cheers!
__________________________________________________________
MODEL : LG Optimus GT540 (Rooted)
MOD : SwiftDroid v2.0 M6 (Based on CyanogenMod v7.1 RC0)
KERNEL : 2.6.29 (VirtualBox #309)
BUILD : GRJ22
RECOVERY : ClockworkMod Recovery v4.0
___________________________________________________________
BusyBox v1.19
SuperUser v2.3
SetCPU v2.2
Click to expand...
Click to collapse
Don't think z4root works on the Thunderbolt just search youtube for Thunderbolt root and watch the tutorials. Links are provided for everything that needs to be downloaded.
Sent from my ADR6400L using XDA Premium App
I know z4root doesn't work for any modern HTC. You can have permanent root without s-off. The only way to do that is through ADB, using an engineering hboot, and applying various exploits. All the "easy" root methods are just scripts that do what jcase's guide lays out. And unlike the guide, if something goes south, you're lost and screwed. I think it would be safe to say "easy" roots have probably bricked more phones than anything else.
loonatik78 said:
I know z4root doesn't work for any modern HTC. You can have permanent root without s-off. The only way to do that is through ADB, using an engineering hboot, and applying various exploits. All the "easy" root methods are just scripts that do what jcase's guide lays out. And unlike the guide, if something goes south, you're lost and screwed. I think it would be safe to say "easy" roots have probably bricked more phones than anything else.
Click to expand...
Click to collapse
Is that u dbzfanatic? Looks awfully similar, lol.
Sent from my ADR6400L using XDA Premium App
nerogold said:
Is that u dbzfanatic? Looks awfully similar, lol.
Sent from my ADR6400L using XDA Premium App
Click to expand...
Click to collapse
Nope. Just a pieced up, inked up, "I been everywhere, man", freak of many talents and interests. Android phones are just one of them.
loonatik78 said:
Nope. Just a pieced up, inked up, "I been everywhere, man", freak of many talents and interests. Android phones are just one of them.
Click to expand...
Click to collapse
Sorry man I just wanted to say thanks to the other user I mentioned ,his method of rooting was and still is a great help to me already rooted 5 bolts and currently on #6 as I'm typing.
Sent from my ADR6400L using XDA Premium App
Do a google search for thunderbolt auto root. There is one posted in the Thuderbolt forums. I can't link directly to it because I don't have enough posts yet. I tested it on my wife's thunderbolt without a problem.
Greywolf66 said:
Do a google search for thunderbolt auto root. There is one posted in the Thuderbolt forums. I can't link directly to it because I don't have enough posts yet. I tested it on my wife's thunderbolt without a problem.
Click to expand...
Click to collapse
Yep, and the past guy to go that route, after being warned it was highly prone to failure, had it fail. Then he came back looking for help, but nobody could because what went wrong wasn't at all clear. Just not wise.
Ive used the one click root four times with no issues. Four diffrent tb's from 3 diffrent states. 2 of them had alrdy takin the ota's. Dont have the link handy but if was a time saver. Though a half arse understanding of the method helps avoid issues. Ill post the link when i get home.
Sent from my ADR6400L using XDA Premium App
loonatik78 said:
Yep, and the past guy to go that route, after being warned it was highly prone to failure, had it fail. Then he came back looking for help, but nobody could because what went wrong wasn't at all clear. Just not wise.
Click to expand...
Click to collapse
I rooted mine manually first. As you said in a previous post most "easy" roots are just scripts. That's what the one I used on my wife's was. I was following along the text of the batch file as I was running it so that if something happened I would know at what part of the script I was at. I had no problems with it though.
I'll agree that I could see where if someone where to run into a problem using script without any knowledge of what the script was doing they would probably end in a very bad place.
I think the obvious was missed in this thread: The OP is not a candidate for rooting. It's a risky task for experienced users and a non-task for noobs. He hasn't even stated a valid need for rooting the phone.
TabGuy said:
I think the obvious was missed in this thread: The OP is not a candidate for rooting. It's a risky task for experienced users and a non-task for noobs. He hasn't even stated a valid need for rooting the phone.
Click to expand...
Click to collapse
Come on, cut him some slack. Everyone was new once. He has already been warned.
Sent from my ADR6400L using XDA App
priapos said:
Thanks for the quick reply.
I am not nervous, I just don't understand what any of this is.
I don't know what adb is or how to use it.
I don't know what copy and pasting the commands means.
I certainly don't know what "validate checksums" are.
I realize I am coming across as a comlete shmo, but explaining how to do this with more computer jargon doesn't clarify the process.
I really need instructions for dooshbags like me.
Thanks in advance.
Click to expand...
Click to collapse
ADB "Android Development Bridge" Simply put just helps you develop apps and fix bugs. (In this case, you will use this to reinstall Android without a locked bootloader (a.k.a. S-Off) (the bootloader is code that is run when you first turn on your device that tells Android to run).
You don't have to know how to use ADB, but you must install it on your computer.
As far as copying and pasting commands go, the tutorial that you choose to visit will tell you to type this command ex: cp image.zip/sdcard/
You will just copy this code out of your browser (FireFox/Internet Explorer/Chrome/etc.) and paste it into a command line.
Your command line will depend on what operating system you use on your pc. Ex for Windows, you will use "Command Prompt" or on Linux/MAC you will use "Terminal".
As far as validation checksums goes, it is used to make sure that the file that you downloaded is 100% the same file that the developer made.
Basically, open up your command line and type (without quotes) "md5 image.zip" also, make sure you change to "image.zip" with whatever/where you file is at.
I would be more specific with these instructions I'd I knew what OS (operating system) you are using on your computer is.
After you type in the command and hit enter, it will spit out a long string of gibberish. Just make sure this "checksum" is the EXACT same as whatever the devolver put in the tutorial you are following.
As far as putting together an idiot proof guide, you will have to forgive us, but I don't think the people here want to have a bunch of people here flooding the forums with very basic questions that have been answered already on the internet. However, don't let that stop you from asking questions. Just make sure you help yourself first (Google what you don't understand) and then ask for clarification.
P.S. I claim touchscreen amnesty for any typos.
Sent from my ADR6400L using XDA App
Hey xda. Sorry if this post has been misplaced, but I noticed there is no device forum for the tablet I am asking about today, and that is understandable. My girlfriend recently got an eMatic eGlide Pro II XL tablet for her birthday and it is running Android Ice Cream Sandwich 4.0.3. I noticed that it had a lot of bloatware and no google play store on it, and she wanted the play store, so I rooted the device for her and installed the play store and it works like a charm. The only problem I seem to have run into is this read only folder called "oem". The path for this partition is /oem/ and there are a few bloatware apps in there. For some reason though, I cannot edit or delete anything in that partition as it says it is read only even though i am using the root functions of ES File Explorer. I am able to modify other system apps though root explorer. I even tried using terminal emulator commands to remove the items but it still didn't work. Is there a way I can mount this folder as read/write? If I can, that would be a blessing, as I could delete the crapware that came with the tablet and the old version of YouTube that is buggy and not updateable thanks to being placed in the oem folder. Thanks for reading all this guys, I know it's a wall of text, haha.
Ematic: What is the browser?
What is the browser that is install from factory.. on Ematic devices ..as it is not "Chrome" [It almost looks like Dolphin], when I tried to do a regular .apk install of "Chrome" from the Google store it dies which almost tells me that it need to be pushed into the device. So am I correct that I need to find a downloadable .apk of "Chrome" for Android 4.0.3 ?
bfrench1990 said:
Hey xda. Sorry if this post has been misplaced, but I noticed there is no device forum for the tablet I am asking about today, and that is understandable. My girlfriend recently got an eMatic eGlide Pro II XL tablet for her birthday and it is running Android Ice Cream Sandwich 4.0.3. I noticed that it had a lot of bloatware and no google play store on it, and she wanted the play store, so I rooted the device for her and installed the play store and it works like a charm. The only problem I seem to have run into is this read only folder called "oem". The path for this partition is /oem/ and there are a few bloatware apps in there. For some reason though, I cannot edit or delete anything in that partition as it says it is read only even though i am using the root functions of ES File Explorer. I am able to modify other system apps though root explorer. I even tried using terminal emulator commands to remove the items but it still didn't work. Is there a way I can mount this folder as read/write? If I can, that would be a blessing, as I could delete the crapware that came with the tablet and the old version of YouTube that is buggy and not updateable thanks to being placed in the oem folder. Thanks for reading all this guys, I know it's a wall of text, haha.
Click to expand...
Click to collapse
How did you root the tablet? it seems there are several Ematic tablets being sold at wal-mart and I think people would like to know how you rooted it. (I know I would.)
fsuinnc said:
How did you root the tablet? it seems there are several Ematic tablets being sold at wal-mart and I think people would like to know how you rooted it. (I know I would.)
Click to expand...
Click to collapse
I used a tool called Root with Restore by Bin4ry. It took me a couple times. The first time I did it, all it managed to do was slow the tablet down, then i just performed a factory reset and tried again using the same process until it worked. It didn't take all that long. The hardest part is getting the adb drivers to recognize the tablet. I will attach my adb drivers so you don't have to go through all the rigamarole.
Navigate to wherever your android sdk folder is. Mine is at C:\Program Files (x86)\Android\android-sdk
Within the android-sdk folder, look for extras, then google, then usb_driver. Make a backup of everything in your usb_driver folder, just in case.
Next just extract the contents of the zip I attached to this post. Make sure USB debugging is on, and plug it in. It should be recognized assuming there isn't some other problem i haven't encountered or forgot to mention.
Once your computer recognizes the adb interface for your tablet, use the Root with Restore tool until it works.
bfrench1990 said:
I used a tool called Root with Restore by Bin4ry. It took me a couple times. The first time I did it, all it managed to do was slow the tablet down, then i just performed a factory reset and tried again using the same process until it worked. It didn't take all that long. The hardest part is getting the adb drivers to recognize the tablet. I will attach my adb drivers so you don't have to go through all the rigamarole.
Navigate to wherever your android sdk folder is. Mine is at C:\Program Files (x86)\Android\android-sdk
Within the android-sdk folder, look for extras, then google, then usb_driver. Make a backup of everything in your usb_driver folder, just in case.
Next just extract the contents of the zip I attached to this post. Make sure USB debugging is on, and plug it in. It should be recognized assuming there isn't some other problem i haven't encountered or forgot to mention.
Once your computer recognizes the adb interface for your tablet, use the Root with Restore tool until it works.
Click to expand...
Click to collapse
Thanks, that's great info. I will try it out. (I have a Ematic egs005 7" on it's way to me. they seem to be very cheap right now at under $60)
fsuinnc said:
Thanks, that's great info. I will try it out. (I have a Ematic egs005 7" on it's way to me. they seem to be very cheap right now at under $60)
Click to expand...
Click to collapse
I'll bet that you can get it rooted. You may have to edit those drivers though since I don't think my girlfriend's tablet isn't the same as the one you mentioned.
If the drivers I posted don't work for you, then open up "android_winusb.inf" from that zip file in your favorite text editor.
Somewhere under the "[Google.NTx86]" and "[Google.NTamd64]" sections, add this:
;eMatic egs005
Remember where you put those, cause what goes under those entries is the hardware ID of your tablet. You can get that by going under device manager and right clicking on your tablet, if it is unrecognized it should have a yellow triangle on it or something like that. Go to properties and go to the details tab, then from the drop down menu, select hardware IDs. In my case, two came up. Just pick one. If that one ends up not working later, use the one you didn't try.
Now, your entries should look like this:
;eMatic egs005
%CompositeAdbInterface% = USB_Install, (your hardware ID)
Next, try to update the drivers on your tablet via device manager. Right click on your tablet like we did last time, and click properties. Go to the driver tab, and hit the update driver button. You'll have to manually navigate to where your drivers are. Select the folder where you extracted the zip to (make sure you have the edited file in there!) and follow the procedure to update the driver.
Next, open up an adb window and type in adb devices. If you have something showing up, congrats! You should be able to try the root tool now. As always, be careful!
eglide pro ll xl
I just bought the eglide pro ll xl also. From what I have read and done to my tab so far, it is already rooted from the factory. It sounds like a lot of the ematic tabs are. I've been researching different operating systems to put on my tab but there isn't anything that says it is specifically for mine. They pretty much just list the types of tablets the ROMS will work for. The question I have is what type of tablet is this. Allwinner a10? LY F1? TREQ? I would really like to know this and a good way to back up my current system so if I screw it up I can go back and try again.
-Z
Livinbad said:
I just bought the eglide pro ll xl also. From what I have read and done to my tab so far, it is already rooted from the factory. It sounds like a lot of the ematic tabs are. I've been researching different operating systems to put on my tab but there isn't anything that says it is specifically for mine. They pretty much just list the types of tablets the ROMS will work for. The question I have is what type of tablet is this. Allwinner a10? LY F1? TREQ? I would really like to know this and a good way to back up my current system so if I screw it up I can go back and try again.
-Z
Click to expand...
Click to collapse
I didn't add most of those entries in the drivers file, it originated as a sort of "fix all" driver that was posted on xda to connect many many types of different devices to adb without hassle. I added a few of the entries using the hardware ID method I described above to accommodate some less popular devices that my friends and family asked me to root.
I think I heard talk somewhere about custom roms for the eGlide, but I have no clue how to flash them, and seeing as how that tablet wasn't mine, I did not want to try to flash one and brick it, lol. I couldn't find any recoveries or any other tool to flash things to it. If you do find a way, all I can say is be careful.
As far as backing up goes, root with restore supports unrooting as well. I never performed that function though, since root hasn't done anything bad for the tablets I put them on, haha. I'm not certain there is an easy backup method since as I said a second ago, no custom recoveries. To be safe, I would recommend a factory data reset before attempting any rooting/unrooting of this tablet.
I hope I helped with my feedback.
bfrench1990 said:
I didn't add most of those entries in the drivers file, it originated as a sort of "fix all" driver that was posted on xda to connect many many types of different devices to adb without hassle. I added a few of the entries using the hardware ID method I described above to accommodate some less popular devices that my friends and family asked me to root.
I think I heard talk somewhere about custom roms for the eGlide, but I have no clue how to flash them, and seeing as how that tablet wasn't mine, I did not want to try to flash one and brick it, lol. I couldn't find any recoveries or any other tool to flash things to it. If you do find a way, all I can say is be careful.
As far as backing up goes, root with restore supports unrooting as well. I never performed that function though, since root hasn't done anything bad for the tablets I put them on, haha. I'm not certain there is an easy backup method since as I said a second ago, no custom recoveries. To be safe, I would recommend a factory data reset before attempting any rooting/unrooting of this tablet.
I hope I helped with my feedback.
Click to expand...
Click to collapse
I actually installed CWM 6.0.1.2 by Flowish on to my tab and it works great except for the process he has to get in to the recovery. I have to use the terminal emulator to launch it. That's why I am leery about installing a different ROM. If I can't get the thing to boot up properly I then can't get to the terminal emulator to get to recovery to restore my backup. I'm still searching and learning though. I'll figure it out eventually.
Livinbad said:
I actually installed CWM 6.0.1.2 by Flowish on to my tab and it works great except for the process he has to get in to the recovery. I have to use the terminal emulator to launch it. That's why I am leery about installing a different ROM. If I can't get the thing to boot up properly I then can't get to the terminal emulator to get to recovery to restore my backup. I'm still searching and learning though. I'll figure it out eventually.
Click to expand...
Click to collapse
Check if there's fastboot for this tablet. There's a fastboot command to boot into the recovery. If not, then I would just not flash a Rom
This guide assumes that you are on a stock Pantech Flex P8010 running either ICS (v4.0.4). or the updated JB (v4.1.2) Please note that rooting a ICS phone has been known to cause issues when trying to run the over the air update. If you have already rooted and are looking for a way to update to JellyBean please skip to the section on updating, if this isn't you keep reading.
So at this point you have decided to continue. You shouldn't run into any issues if you follow the directions and you shouldn't mess your phone up even if root doesn't take. However, in the spirit of covering ones back side....
I am not responsible for anything that goes wrong.
Jelly Bean 4.1.2 or ICS 4.0.4
This method was found by LuneBear and has not been tested by myself so I cannot personally verify its effectiveness. I did check and it seems to work with both ICS and JB but your mileage may vary. You will need to download SRSroot and install it on a Windows machine.
SRS ROOT
SRS Homepage
Make sure that USB debugging is enabled on your phone. Connect your phone via USB and run the program. Select the button for all root methods. Then you will need to select the Legolas exploit. Once everything is done (may take some time) just reboot the phone and you should be good to go.
Ice Cream Sandwich 4.0.4 ONLY
Windows Option
This method has been tried on a number of Windows versions and some work some don't so your mileage may very. This method uses Bin4ry's Root method and was orgnially discovered by aaki_rocker and is WAY LESS COMPLICATED. However please note that some users have had issues using this method with Bin4ry's latest version of the root script. It is recommended that you download an older version if you run into any issues or the root doesn't take.
First lets get some drivers on your Windows box. To do this you will need to download the Pantech PC Suite and install it.
http://c724062.r62.cf2.rackcdn.com/PantechPCSuite_1.1.1.3437.exe
Next you will need to download and extract Bin4ry's root script.
http://ul.to/z7krermj
Once you have these two files you will need to plug your phone into the PC via USB and enable the USB type as Data Mode.
Next run the Bin4ry's script and follow the directions when in doubt about what to choose select the simplest option in all cases.
If everything goes well you will have a nicely rooted phone.
Linux Option
This is not a point and click root and is not for the faint of heart. This method of rooting is based off of Bin4ry's root for ICS/JB. Changes have been made to the srcipt to allow it to work with the Flex please follow the steps below and you will have root in just a few minutes. It will probably take you longer to download the files you need than to actually root the phone.
This method has been performed successfully using Ubuntu 12.10 64bit it may work with other versions of linux but it will not work with Windows due to the driver issues and the fact that I didn't alter the windows batch file, in fact I removed any windows related files from Bin4ry's original package.
First you will need to set up the linux machine if you don't already have it. This can be done in one of a few ways you can run a live copy using a Live CD/USB boot (this will not install linux on your computer unless you tell it to) or you can install it in the standard manner or using WUBI, the third option us setting up linux in a virtual machine. If you don't know how to do this google it, there is a wealth of information out there on these subjects and probably some you can even understand without a degree in astro-physics.
Second you will need to set your phone up so that USB debug mode is turned on [settings>developer options]. Make sure you phone isnt plugged into the USB or it won't let you change the setting.
Now plug your phone into to the (linux) computer with the USB. Next you will need to set the USB computer connection type to Media Device(MTP)
In order for the computer to communicate with the phone we will need to install Android Debug Bridge (ADB) and create a couple of files.
These files will basically trick the computer into thinking it has actual drivers for the phone.
Open a terminal window, and enter the following (this will install ADB):
sudo apt-get install android-tools-adb
Once this is done enter the following
sudo gedit /etc/udev/rules.d/70-android.rules
Gedit will open at this point copy the the following into it and then click save and close the window.
SUBSYSTEMS=="usb", ATTRS{idVendor}=="10a9:6055", MODE="0666"
In the terminal window enter this (yeah I know it looks the same just go with it)
sudo gedit /lib/udev/rules.d/70-android.rules
After the window opens paste the same line of code into the file that you did in the previous files, save and close.
Test your connection by issuing the following command in the terminal window:
adb devices
Should see something similar to:
OSCAR01111112010204 device
Your adb is now recognizing your phone and you can now move on to the next step if you are not getting this don't even bother moving to the next step it wont work. If you don't see this check your settings and go again.
Ok so you are now ready to actually root the phone. The first thing your going to need to do is download my modified Bin4ry script. See the attached file.
After you have it downloaded you will need to extract it you can do this by opening the file manager (click on the home folder icon) and going to download. Find the file called Root_Flex.zip. Right click on it and select EXTRACT HERE. After its done extracting you should see a directory called Root_Flex. In a terminal windows enter the following:
cd Downloads/Root_Flex
Your prompt should now look something like
[email protected]_name~/Downloads/Root_Flex$
From here just enter the command:
bash RunMeFlex.sh
At this point you should see a bunch of junk come up and a menu asking which way you want to try to root. Type 1 and press enter. It will give you 3 errors, ignore them. It should copy a bunch of files and ask you to press restore on your phone, do it. It should ask you to press Enter to reboot the phone, do so and the phone will reboot. It should be waiting on you to press enter again dont press enter until the phone is completely rebooted and for good measure give it an extra few seconds. The script should finish and the phone will reboot again this time you should see a little box with an update appear on the phone. At this point you should be rooted. If not try the script again.
I hope this helps out a lot of folks out there. Let me know if I need to change anything in this How to or if I made any mistakes along the way.
Updating If you're already rooted
So you rooted your phone and now you want JellyBean but when you run the update you get the dead droid image and the update fails OR you live in an area that isn't covered by AT&T and you want the update, what do you do? Well thanks to some hard work by Attn1 we have a solution and its pretty simple. First off you will need to have CWM running on the phone. Now there are a few ways to go about this but the method I used was here:
http://forum.xda-developers.com/showthread.php?t=2133857
You only need to go as far as getting CWM up an running on the phone you do not need to install it as the the update by Attn1 will take care of a full install of a better version. You will need to have a copy of Fastboot.exe and some img files. Below is a rar file that has all the necessary files to get CWM running (not installed) on the phone using windows (sorry I don't have the linux files for this one). Just unpack them into a convienent folder somewhere and follow the instructions on the link above.
http://tinyurl.com/oa2p48f
I recommend using the boot_external.img but if you do not have an external SD card and only have the internal storage just use boot_internal.img instead. This method relys on you being able to get into fast boot. If you do not have access to fastboot for what ever reason I suggest you jump ahead in the thread and read Attn1 methods for installing CWM:
http://forum.xda-developers.com/showthread.php?t=2008888&page=44
Next get the update files from this link (second post)
http://forum.xda-developers.com/showthread.php?t=2008888&page=47
Once you have all the files downloaded and copied everything to the appropriate SD cards on your phone your ready to go. If you don't know how to do this don't even think about anything else till you learn this. After this is all done follow the directions below (copied from Attn1's post)
Procedure if you ARE NOT running baseband JYUS06032013 (ICS Basebands) :
boot ICS CWM
flash FLEX-JB-JYUS06032013-FIRMWARE.zip from CWM
format system in CWM (will NOT wipe data, but makes sure old rom does not flash back stock recovery)
restart start recovery/adb reboot recovery (JB CWM is installed - do not try to fastboot boot ICS CWM)
flash FLEX-JB-JYUS06032013-ROM.zip from CWM.
reboot
Procedure if you ARE running baseband JYUS06032013 (JB Baseband) :
get root (Instructions HERE - use GANDALF)
install CWM (Instructions HERE)
flash FLEX-JB-JYUS06032013-FIRMWARE.zip from CWM
format system in CWM (will NOT wipe data, but makes sure old rom does not flash back stock recovery)
reboot to CWM
flash FLEX-JB-JYUS06032013-ROM.zip from CWM.
reboot
This ROM is Pantech stock with no mods other than CWM installation protection and all stock permissions and symlinks carefully maintained and consistent with the product of a successful OTA.
The firmware is also stock, with the exception of the open aboot allowing fastboot boot <bootimage>, and installation of JB CWM with nothing else added or changed. It runs well with nothing broken. You MUST be on JB firmware (below) to run it properly.
You can let the new CWM root it if you like when you exit - it will prompt you. It will also prompt you to disable CWM on reboot make sure this gets disabled or the phone will keep booting to CWM rather than the ROM.
Downloads:
md5: 1a0ca5f177bce2f4c428931616e0ecd1 FLEX-JB-JYUS06032013-FIRMWARE.zip
md5: 17c0e611ab6dfbca230571c1e40f3d14 FLEX-JB-JYUS06032013-ROM.zip
Make sure you check the md5sum on the files before you flash them if there wrong download them again this is vital.
If you need a program to check md5sums copy this .exe file to your c:\windows\system\ and run it from the command line.
http://tinyurl.com/l74wl9q
Thanks go to Bin4ry for the original script and all the technical help provided.
Check out the thread and give a thanks and donate a few bucks if you can.
http://forum.xda-developers.com/showthread.php?t=1886460
Thanks to Atadres for getting me going in the right direction and help testing along the way.
Thanks to Esau Silva for this post that helped get the drivers working for us in Ubutnu.
http://esausilva.com/2010/05/13/setting-up-adbusb-drivers-for-android-devices-in-linux-ubuntu/
Thanks to Aaki_rocker for coming up with the Windows version of this root method you can find his original post here.
http://forum.xda-developers.com/showthread.php?t=2141538
Thanks to LuneBear for finding the root method for JellyBean.
Thanks to Attn1 for the JellyBean update and CM 10.2 version of CWM Recovery.
jist a quick memo guys when you issue the command adb devices please cd to proper android sdk platform tools folder or else youll get an error like no command did you mean..... heres the proper way do this step before you do the adb devices step type in cd ~/android-sdk-linux/platform-tools press enter then type in ./adb devices
i am now trying to contact team win for help with porting the recovery image team win recovery so we can start roming this device and adding ports and roms
atadres said:
jist a quick memo guys when you issue the command adb devices please cd to proper android sdk platform tools folder or else youll get an error like no command did you mean..... heres the proper way do this step before you do the adb devices step type in cd ~/android-sdk-linux/platform-tools press enter then type in ./adb devices....
Click to expand...
Click to collapse
Acutally this assumes you are on a completely fresh install and did not have adb installed through the platform tools if that is the case everything I typed up will work. However you are correct too. Let me know if you think I should go ahead and rework the stuff to be a little more universal if so please PM me an update of the commands.
your right my apologies but one thing i noticed that i would like to say idk if its my experiance or universal after successfully rooting the flex the lockscreen fails to resize itself leaving a black space where the onscreen dock is usualy located no big issue though and the rooting was easy and painless once adb was set up correctly 100000+ points thanks so much
Good job guys. Respect! I have a Pantech Flex, which is an awesome device with the same specs (things that matter to me) as S3, but without big name. I like Pantech Flex because it's size is much better for me than.
The only thing now is to create a ROM! Is it difficult to make a pure Android ROM? Nothing additional, just a pure Android like in Nexus?
Again, thank you guys for your dedication! I'll definitely donate as soon as I have Jelly Bean loaded on my Pantech Flex!
Thanks, this worked great. I am gonna start on a ROM. Hope I don't get bricked.
Sent from the new Pantech Flex. Nominated best lowest priced new smartphone. U jelly I paid nothing, for a phone almost as good as the Galaxy S3?
HighCommander540 said:
Thanks, this worked great. I am gonna start on a ROM. Hope I don't get bricked.
Sent from the new Pantech Flex. Nominated best lowest priced new smartphone. U jelly I paid nothing, for a phone almost as good as the Galaxy S3?
Click to expand...
Click to collapse
lets not get ahead of ourselves here guys in order to create a rom we would need to get a custom recovery on our phone this can be achived by mapping out the devices bootloader extracting an img file of it and using koushes clockworks mod recovery creator only when we achive a port of a custom recovery can we make roms and be able to flash them if any of you have knowledge of this as i am a noob when it comes to recoveries pleasae feel free to input we need all the help we can get guys
---------- Post added at 02:03 PM ---------- Previous post was at 01:58 PM ----------
ivansana said:
Good job guys. Respect! I have a Pantech Flex, which is an awesome device with the same specs (things that matter to me) as S3, but without big name. I like Pantech Flex because it's size is much better for me than.
The only thing now is to create a ROM! Is it difficult to make a pure Android ROM? Nothing additional, just a pure Android like in Nexus?
Again, thank you guys for your dedication! I'll definitely donate as soon as I have Jelly Bean loaded on my Pantech Flex!
Click to expand...
Click to collapse
lol right now we need knowledge donations unfourtunatly we cannot start working on roms till we have a custom recovery ported over either team win or clockworks mod recovery this will take a little bit of time and knowledge and to answer your question about the stock nexus rom your talking along the terms of a cynaogen mod port? or akop port looking into it i would say untill we have mapped the bootloader we wouldnt know how diffcult it would be because the simlinks maybe difcult for a phone that has not yet caught fire in the dev world
i wish i had the time to do a recovery myself and get cwm working but with my family and my fulltime job i barely get any time. Im going to spend all my time on this amazing little phone to do what i can. props to the root method it worked flawlessly!!!
Sent from my PantechP8010 using Tapatalk 2
Awesome I'm glad im getting some good feed back on the root. I wasnt sure if I did the rightup correctly and im glad its working out for everyone.
If I get some time I will start looking into a custom CWM and all that junk I have a contact that should be a pretty good help in this just have to find the time to do it.
Yeah after coming from the LG Nitro HD I was surprised at how easy this was to root.
If you want to get together on gtalk we can work on this together. Right now I'm in the process of getting a ROM dump so we can recover our phones from stock images if we happen to mess them up, which I'm sure we will, but that's the best part! Lol.
I can smell CM9 and CM10 calling to this phone!!!
Sent from my PantechP8010 using Tapatalk 2
jSterling said:
Yeah after coming from the LG Nitro HD I was surprised at how easy this was to root.
If you want to get together on gtalk we can work on this together. Right now I'm in the process of getting a ROM dump so we can recover our phones from stock images if we happen to mess them up, which I'm sure we will, but that's the best part! Lol.
I can smell CM9 and CM10 calling to this phone!!!
Sent from my PantechP8010 using Tapatalk 2
Click to expand...
Click to collapse
Yeah I love this phone but I have to say the Pantech launcher kinda pisses me off.
donavan01 said:
Yeah I love this phone but I have to say the Pantech launcher kinda pisses me off.
Click to expand...
Click to collapse
Agreed lol im using nova
I actually don't mind the launcher, its pretty nice compared to other brand launchers. I'm probably going to try launcher pro though that's been my favorite sense I had my prepaid optimus V
Sent from my PantechP8010 using Tapatalk 2
jSterling said:
I actually don't mind the launcher, its pretty nice compared to other brand launchers. I'm probably going to try launcher pro though that's been my favorite sense I had my prepaid optimus V
Sent from my PantechP8010 using Tapatalk 2
Click to expand...
Click to collapse
I had launcher pro and hated it ... check out APEX seems like the stock ICS but with a lot of extras and without the annoying bits of the pantech that make me insane
donavan01 said:
I had launcher pro and hated it ... check out APEX seems like the stock ICS but with a lot of extras and without the annoying bits of the pantech that make me insane
Click to expand...
Click to collapse
hey guys... is there a pantech flex forum????????
also is it possible to unlock the device if you forget the log in pattern????? thanks
I don't know anything about mapping the device. So I am just going to work on a ROM for my infuse.
I will help with anything for testing. A stock image would be awesome. =-)
No flex forum yet.
_______
Sent from the new rooted Pantech Flex. Nominated best lowest priced new smartphone. U jelly I paid nothing, for a phone almost as good as the Galaxy S3?
jSterling said:
I actually don't mind the launcher, its pretty nice compared to other brand launchers. I'm probably going to try launcher pro though that's been my favorite sense I had my prepaid optimus V
Sent from my PantechP8010 using Tapatalk 2
Click to expand...
Click to collapse
sense is my fav launcher and no no forum yet ive requested and gotten no reply smh
did this thread die guys?
atadres said:
did this thread die guys?
Click to expand...
Click to collapse
Wait till after Xmas I bet you a lot of people will get this phone as presents.
donavan01 said:
Wait till after Xmas I bet you a lot of people will get this phone as presents.
Click to expand...
Click to collapse
Yeah I can see that happening. This weekend I am going to work on it to see what I can come up with. I've been so swamped with work and life bs that I haven't had a chance.
No this thread didn't die.
Sent from my PantechP8010 using Tapatalk 2
Does anyone know if Z4Root will work on this tablet? Thanks!
I've been looking for one for 3 days now, I tryed onclickroot and z4root or something like that,, cant find anything Anyone please help!!
I'm still waiting for my tablet to be delivered...I'm gonna try SuperOneClick (crosses fingers)
I got one of these for my daughter for xmas. I spent a few days trying to root it with no luck. I'm not intimately familiar with android (some unix experience), but I tried all the options I could find for rooting Allwinner a10 devices. At first I ran into problems with adb unable to recognize the device for most one-click methods. I downloaded the android tools and was able to connect with the included adb. After studying the scripts, they all use the "adb root" command to gain root access on the device and copy the necessary files. Unfortunately, this command fails using adb from the tools. At first I thought this was due to my adb version, but after doing some research I think it is actually due to the device kernel. I believe it requires reflashing or some exploit to be able to gain root. I was able to install root explorer and I can browse all the necessary directories but I can't modify or copy the necessary files into them. Busybox told me there was an older version installed, but wouldn't let me install a newer version (again I think due to the permissions). Also, superuser would say it installed but the su binary did not show up on the bin directory. As the necessary directories are all owned by root, I couldn't figure out a way to modify the permissions...
I wound up returning the FileMate and got a Lenovo IdeaTab. Got that rooted in no time.
sorry i never saw this post i've bought 2 of these and i rooted them,
i wish i could get a better build for them though, too many app crashes and the internet connectivity sucks
i used a method by Bin4ry called root with restore, v17 worked any ways i have the zip if you would like it
ferny_dx said:
sorry i never saw this post i've bought 2 of these and i rooted them,
i wish i could get a better build for them though, too many app crashes and the internet connectivity sucks
i used a method by Bin4ry called root with restore, v17 worked any ways i have the zip if you would like it
Click to expand...
Click to collapse
Screw it, here it is for future reference.
How'd you do it!?!?
ferny_dx said:
Screw it, here it is for future reference.
Click to expand...
Click to collapse
FileMate Clear T720
Thank you very much for being the only person ever to have posted in regards to this tablet. I just got mine for christmas and have been trying to get it rooted. I've tried a lot of those one-click methods, and I've even tried this Bin4ary method. but it just hangs up on "daemon started sucessfully*"
Can you please direct me to the filemate drivers (if needed)
also, I have usb debugging endable, allowing 3rd party (not secure) files enabled. and pulling my hair out (enabled).
Thanks again.
Also, I'm running windows 7 and 8, (((maybe i should try win7))) hmm. i'll get back to you on that. Anyhow, any advice would be greatly appreciated, since returning it doesn't sound very fun.
jiberish05 said:
FileMate Clear T720
pulling my hair out (enabled)..
Click to expand...
Click to collapse
I laughed so hard. ok your going to have to install drivers by force,
first off do you happen to have android sdk installed? if you don't there is another way but its going to sound weird,
if you do have the android SDK installed:
1. go to your computer manager (by opening explorer, right click on the "computer" group on the left column and select manager)
2. look for any unrecognized item that appears, ( it will most likely be labeled "Clear" with a faded icon and a "?" sign on top
3. right click and choose "Update drivers", it will give you options, choose "Browse my computer for driver software", another option screen will show,
4. at the bottom of the window there will be an option that says "let me pick from a list of device drivers on my computer"
5. on the screen that appears there should be an option that says "ADB Interface", choose this
6. choose "Google, Inc.">"ADB Testing Interface version x.x.x.x" (I chose version 2.1.0.0)
that should do it next time you plug in the tablet try running ddms or open the cmd and type in "adb devices" (assuming you have adb installed) and it should show.
if this helps just hit the thanks button
[edit] I am running windows 8 btw [/edit]
ADB interface doesn't show up
Thank you very much for getting me farther, however I dont see ADB interface. I'm looking into it right now. I just re-installed the sdk drivers and will keep at it.
BTW, is it even worth doing this? the main reason I want to do it, is so i can connect my ps3 remote via bluetooth, and possibly a little overclocking. Have you had any luck OC it?
Thanks again Much appreciated:good:
jiberish05 said:
Thank you very much for getting me farther, however I dont see ADB interface. I'm looking into it right now. I just re-installed the sdk drivers and will keep at it.
BTW, is it even worth doing this? the main reason I want to do it, is so i can connect my ps3 remote via bluetooth, and possibly a little overclocking. Have you had any luck OC it?
Thanks again Much appreciated:good:
Click to expand...
Click to collapse
open up SDK manager and go to Extras>"Google USB Drivers"
also install everything in the "Android 4.0 (API 14)" section, I have other options installed if this still doesn't work.
its worth it just for the extra stuff that root comes with like titanium backup, but you cant over clock, if you go any higher than 1200 MHz it will lock up and you have to force it to reset.
cyberkeeper1 said:
HERE is the link to root as provided earlier
Click Here to download ADB universal drivers. they should work better than the google USB drivers.
---------- Post added at 12:20 AM ---------- Previous post was at 12:11 AM ----------
this seems kind of spammy. What backs up my claim is that you dont have more than 5 posts...
Click to expand...
Click to collapse
Thanks for the link to my post on android central, the link in that post just comes back the xda thread
Root MANY ANDROID! [Upd: 20.11.2013] - Added Z1 Root
Sent from my XT862 using Tapatalk
Rooted Filemate Clear
I just wanted to confirm I have also rooted the Clear with the Bin4ry v33 exploit using option 1. Although I received the following error:
remote object '/system/bin/ric' does not exist
.
Going to copy files to it's place
Rebooting again, please wait!
Could Not Find C:\Documents and Settings\Graham School\My Documents\Downloads\Ro
ot_with_Restore_by_Bin4ry_v33\ric
Restoring previous Backup! Please select the RESTORE MY DATA option now on your
device!
SuperSu installed and root apps working.
Rooted With Kingo
I just bought one of these cheap to play with and used Kingo to root it. Worked first time, no problem. The only issue I am having is that the SuperSu binaries are failing to update but root is still working. Titanium is working and Root Explorer so I can debloat. Hope that helps is anyone is still trying to use these
Jfender1005 said:
I just bought one of these cheap to play with and used Kingo to root it. Worked first time, lem. The only issue I am having is that the SuperSu binaries are failing to update but root is still working. Titanium is working and Root Explorer so I can debloat. Hope that helps is anyone is still trying to use these
Click to expand...
Click to collapse
please tell me where in the world you got the Kingo root?
As far as being unable to update binaries, try to find a custom recovery and install. From there, you can inject them via su-binary update.zip and bam!
Kingoroot
cyberkeeper1 said:
please tell me where in the world you got the Kingo root?
As far as being unable to update binaries, try to find a custom recovery and install. From there, you can inject them via su-binary update.zip and bam!
Click to expand...
Click to collapse
http://www.kingoapp.com/android-root.htm
That is the link for the Kingo site. The first time I saw it on here there was some question about whether it was safe becase it is not open source and used a Chinese SuperSu app. I felt safe using it on a tablet because I do no banking on it or anything, but the newest posts I have seen are that Kingo is safe. Hope that helps. And if you know where to find a custom recovery that will work with this app please let me know.