Database Info

AC discharges instead of charging

Hello to all XDA-Developers and mortals
After years of using this forum and always being helped by just using the search function, this time I need to make this Post to hopefully get some help.
I have right now a touch Pro, with the original rom from HTC support site on my tPro. (Before it was several different Energy roms)
since a week my only chance to get my tPro charged is, using a USB connection cable since the original charger won't charge furthermore it discharges my device in less than e few minutes. I can actualy watch it sucking it out.
hase anybody an Idea what might fix this problem.
I want to (miss)use this post to thank all the chefs and developers that have worked on improving our everyday experience with our devices.
thank you all.

just go to start-->settings-->system-->battery and should say something about not charging on pc and you should be set from there

XERO_Racer said:
just go to start-->settings-->system-->battery and should say something about not charging on pc and you should be set from there
Click to expand...
Click to collapse
there is the option that says [do not charge over USB if conected to PC]
if I uncheck this one it won't even charge over USB, but my problem is that the battery is not charged with the original charger.

s.zamani said:
there is the option that says [do not charge over USB if conected to PC]
if I uncheck this one it won't even charge over USB, but my problem is that the battery is not charged with the original charger.
Click to expand...
Click to collapse
have u shut off the phone properly and take out the battery for like 30 seconds and putting it back in and connecting the charger? if that doesnt work, look for a spare USB cable sometimes USB cables give in at times, or look for a usb ac charger

[Q] Atrix 2 soft brick

Hi all,
I have an Atrix 2, where the phone wont boot up without a charger. And even if its connected with charger, it only boot to motorola logo, and shows battery level before goes completely blank.
I heard flashing the firware again using RSD lite, with phone connected to PC with fast boot mode will fix this, but I can't disconnect the charger from the phone, and booting the phone while its connected to USB wont work.
I can boot into the OS when going to bptools in recovery mode tho. Can any one help?
Thanks in advance.

angelflames1337 said:
Hi all,
I have an Atrix 2, where the phone wont boot up without a charger. And even if its connected with charger, it only boot to motorola logo, and shows battery level before goes completely blank.
I heard flashing the firware again using RSD lite, with phone connected to PC with fast boot mode will fix this, but I can't disconnect the charger from the phone, and booting the phone while its connected to USB wont work.
I can boot into the OS when going to bptools in recovery mode tho. Can any one help?
Thanks in advance.
Click to expand...
Click to collapse
the thread about soft brick is just above your thread so please search before creating new thread...
anyway here it's:
http://forum.xda-developers.com/showthread.php?t=1937112
for more easier tutorial check this video..it really helped me at my first brick
http://www.youtube.com/watch?v=AHaEHjSzvQQ

رامز said:
the thread about soft brick is just above your thread so please search before creating new thread...
anyway here it's:
http://forum.xda-developers.com/showthread.php?t=1937112
for more easier tutorial check this video..it really helped me at my first brick
http://www.youtube.com/watch?v=AHaEHjSzvQQ
Click to expand...
Click to collapse
Hi there, thanks for replying. As I mentioned in my first post, my phone wont boot up when connected to the PC. It can only boot when connected to the wall charger. So I cant really flash it using RSD Lite. Is there anyway to work around this problem? When in fast boot mode (and connected with wall charger), it says battery low cannot program. Does this means something?

angelflames1337 said:
Hi there, thanks for replying. As I mentioned in my first post, my phone wont boot up when connected to the PC. It can only boot when connected to the wall charger. So I cant really flash it using RSD Lite. Is there anyway to work around this problem? When in fast boot mode (and connected with wall charger), it says battery low cannot program. Does this means something?
Click to expand...
Click to collapse
in the youtube video..it's mention that you must have about 60% battery or above so fast_boot will tell you "battery OK" but in your case you've a low battery that's why fast_boot tells you "battery low".
The only solution to recharge it is to take battery off from phone and charge it using another atrix or a generic battery wall socket or any other method as phone itself will never charge the battery in Soft Brick...
.
Don't worry I had the same issue before but I used a small trick to charge my battery..I've an Arduino board "small development board" came with an adapter 7V 1amp so I take 2 wires from the arduino and connect that adapter "inner is + and outer is -" to the battery "look at the battery back it's mention where is + and where is -" and waited for an hour then put battery back in phone and enter fast_boot mode then voila! it said battery OK which means it has been charged successfully then FXZ normally.
Note: be sure to connect positive+ at adapter to positive+ at battery and same connect negative- to negative- DON'T reverse the signs.

رامز said:
in the youtube video..it's mention that you must have about 60% battery or above so fast_boot will tell you "battery OK" but in your case you've a low battery that's why fast_boot tells you "battery low"...the only solution to recharge it is to take battery off from phone and charge it using another atrix or a generic battery wall socket or any other method as phone itself will never charge the battery in Soft Brick....don't worry I had the same issue before but I used a small trick to charge my battery..I've an Arduino board "small development board" came with an adapter 7V 1amp so I take 2 wires from the arduino and connect that adapter "inner is + and outer is -" to the battery "look at the battery back it's mention where is + and where is -" and waited for an hour then put it back in phone and enter fast_boot mode then voila it said battery OK which means it has been charged successfully then FXZ normally.
note: be sure to connect positive+ at adapter to positive+ at battery and same connect negative- to negative- DON'T reverse the signs.
Click to expand...
Click to collapse
As he says you are going no where if you dont have at least 60% battery charge, to make sure better be fully charge. Or your risk to hard-brick your phone.

Why won't my tablet start?

Sorry if this is the wrong board but I'm new to XDA :/
So one day I left my Versus touchtab to charge and then when I came back it wouldn't turn on. The problem is that sometimes when I plug it in the tablet would act as though it's charging but it wont so I run out of charge. My theory is that it didn't charge properly and it's completely out of juice. Please could anyone tell me why they think it's not working and how to fix the issue. Thanks in advance!
P.S It doesn't charge via micro USB and I've already been told to charge it via USB and it's actual charger many times!

[Completed] [Q] nook color charging

i broke my factory charger im using micro usb its just blank no battery low sign just blan nothing been charging for hours im clueless can anyone help me please:confuse

johnphonegeek316 said:
i broke my factory charger im using micro usb its just blank no battery low sign just blan nothing been charging for hours im clueless can anyone help me please:confuse
Click to expand...
Click to collapse
What is blank? Do you mean your device is not turning on, or that your battery is not charging?
Try using another charger. Maybe the current one is busted or there may be a problem with the USB cable. Give it a try.

J700p Fixable or Dead?

So a coworker asked me to help out with his phone, said someone failed a flashing or something, ok cool I can check it out for ya...
Wont turn on unless plugged into a wall charger.
Wont charge on pc usb, battery screen loops when on wall charger, can power on while on wall charger but is bootlooping samsung boot screen and can get into download mode but that is it.
Cant connect to pc since it dies as soon as wall charger is unplugged.
I have tried leaving it on the charger for 12 hours, tried it in battery screen and download mode, wont power on without being on the wall charger...
Idk what to do guys, I'm decent at flashing things and tweaking with stuff, but this one has me stumped. I got the stock files for it ready to flash, just gotta find a way to be able to have it power on when connected to my PC
It is a sm-j700P boost mobile.
Any advice would be nice, thanks.

mortj19 said:
So a coworker asked me to help out with his phone, said someone failed a flashing or something, ok cool I can check it out for ya...
Wont turn on unless plugged into a wall charger.
Wont charge on pc usb, battery screen loops when on wall charger, can power on while on wall charger but is bootlooping samsung boot screen and can get into download mode but that is it.
Cant connect to pc since it dies as soon as wall charger is unplugged.
I have tried leaving it on the charger for 12 hours, tried it in battery screen and download mode, wont power on without being on the wall charger...
Idk what to do guys, I'm decent at flashing things and tweaking with stuff, but this one has me stumped. I got the stock files for it ready to flash, just gotta find a way to be able to have it power on when connected to my PC
It is a sm-j700P boost mobile.
Any advice would be nice, thanks.
Click to expand...
Click to collapse
Have you tried replacing the battery?