Database Info

[Q] Dead Phone

Hi all, I just tried to update my phone via LGMobile update software, and it strangely died never to power up.
The software went through the usual checks and started to download over 400mb file, it was about 80 percent when I last looked, but because the file was large and was taking time I was doing something else, when I returned back the phone was off and I had this error message
Code:
Updating is not possible any longer
due to a fatal error while the LG Mobile Phone Software Update
on the update software.
I tried to switch the phone on to no avail, I tried recovery phone method and that also fails with above error message.
Also when I have phone plugged in usb I don't see battery charge screen, so can't press upvol+power.
Any help would be appreciated.
Thanks

coolfi said:
Hi all, I just tried to update my phone via LGMobile update software, and it strangely died never to power up.
The software went through the usual checks and started to download over 400mb file, it was about 80 percent when I last looked, but because the file was large and was taking time I was doing something else, when I returned back the phone was off and I had this error message
Code:
Updating is not possible any longer
due to a fatal error while the LG Mobile Phone Software Update
on the update software.
I tried to switch the phone on to no avail, I tried recovery phone method and that also fails with above error message.
Also when I have phone plugged in usb I don't see battery charge screen, so can't press upvol+power.
Any help would be appreciated.
Thanks
Click to expand...
Click to collapse
Well, do not worry much. Follow the steps as if you turn on, bone, run the LG Update, installing the drivers (make) when your computer is ready, connect your phone to the USB, wait about 20 seconds, now press volume up and power and has about 10 seconds , loose, wait two seconds and you press volume up and power again. If all goes well will recognize your mobile LG Update to reinstall now.
I hope everything goes well, because otherwise you just have the service technician.
a greeting
Español (Spain)
Bueno, no te asustes mucho. Sigue los pasos, como si te encendiera, osea, ejecuta el LG Update, instala los drives (asegurate), cuando tu ordenador este preparado, conecta tu telefono al USB, espera unos 20 segundos, ahora pulsa volumen+ y power y cuenta unos 10 segundos, suelta, espera dos segundos y vuelve a pulsar volumen+ y power otra vez. Si todo va bien LG Update reconocera tu movil y ahora a reinstalar.
Espero que todo salga bien, porque si no, solo te queda el servicio tecnico.
Un saludo

Thanks for the reply m8, I had been trying that but it was not working before.
Left the battery out for 20mins, and I can at last go in to debug mode, but the update hangs at 16% and stops with error "Problem with communication between cell phone and pc". I think it may be the new lg software fault.
Does anyone have an old version of software I can try? Also is there a way to download and restore from pc rather then download each new time the large file.
Update: I had to try a different PC, with windows xp sp2 compatibility and it flashed fully.

Keep trying
I think the problem you have in your PC drivers. Reinstall LG pcsuite and the drivers for the LG Update. The problem is not on the phone.
a greeting
Español (Spain)
Yo creo que el problema lo tienes en los drivers del PC. Reinstala LG PCsuite y los drivers del LG Update. El problema no esta en el telefono.
Un saludo

[Q] moto g died / bricked help!

hi, i'm sorry, but i need help urgently. I unlocked the bootloader and flashed an international firmware so i can update to 4.4.2, since kitkat is not available in my country yet. then i tried to root my phone using superboot-windows.bat, and when the phone restarted it showd the moto logo, but it faded to black. so i turned it off, but now it doesn't turn on. is there a way to turn it on via adb or fastboot from windows?
please help i'm panicking.

cancheritos said:
hi, i'm sorry, but i need help urgently. I unlocked the bootloader and flashed an international firmware so i can update to 4.4.2, since kitkat is not available in my country yet. then i tried to root my phone using superboot-windows.bat, and when the phone restarted it showd the moto logo, but it faded to black. so i turned it off, but now it doesn't turn on. is there a way to turn it on via adb or fastboot from windows?
please help i'm panicking.
Click to expand...
Click to collapse
plug in the pc and show me what says the pc

solved
hi, i conected the moto g to the computer and while holding on/off button i run adb-windows.exe and it rebooted instantly. i don't know what hapenned exactly, but now i have mi cel back. sadly, i don't have root acces, but after this i don't know if i will try it again. thanks for your time!

Flash cwm 6.0.4.6 in development thread and download latest supersu from chain fire website
Sent from my XT1034 using xda app-developers app

cancheritos said:
hi, i conected the moto g to the computer and while holding on/off button i run adb-windows.exe and it rebooted instantly. i don't know what hapenned exactly, but now i have mi cel back. sadly, i don't have root acces, but after this i don't know if i will try it again. thanks for your time!
Click to expand...
Click to collapse
As long as your bootloader works, your phone will always be recoverable. Also, it's almost impossible to kill your bootloader, since the phone prevents you from downgrading it. Moto loves the community, and this is a way to show it; a hardbrick proof phone.

tatazeuz said:
As long as your bootloader works, your phone will always be recoverable. Also, it's almost impossible to kill your bootloader, since the phone prevents you from downgrading it. Moto loves the community, and this is a way to show it; a hardbrick proof phone.
Click to expand...
Click to collapse
yeah, i got scared because it didn't turn on or boot in any way, i tried everithing: torn on botton, log press turn on button, vol- and turn on, lon press booth, and it didn't response... if only the bootloader, but nothing. also the pc didn't recognice it, and i checked the usb power suply, it wasn't receiving any voltage... i was going to send it to the dealer and try my luck, but then the miracle happenned, and now im happy!

cancheritos said:
yeah, i got scared because it didn't turn on or boot in any way, i tried everithing: torn on botton, log press turn on button, vol- and turn on, lon press booth, and it didn't response... if only the bootloader, but nothing. also the pc didn't recognice it, and i checked the usb power suply, it wasn't receiving any voltage... i was going to send it to the dealer and try my luck, but then the miracle happenned, and now im happy!
Click to expand...
Click to collapse
It sounds like it ran out of battery during the procces, and then recovered part of it via usb.

tatazeuz said:
As long as your bootloader works, your phone will always be recoverable. Also, it's almost impossible to kill your bootloader, since the phone prevents you from downgrading it. Moto loves the community, and this is a way to show it; a hardbrick proof phone.
Click to expand...
Click to collapse
Sorry but the other day i kill the bootloader, i flash the .mbn files on the firmware and my phone don't work, only appears qusb-bulk when i connect on the pc, but i have a tool for blank-flash the bootloader and make im work again, seems the tool directly writes the emmc

Boss442 said:
Sorry but the other day i kill the bootloader, i flash the .mbn files on the firmware and my phone don't work, only appears qusb-bulk when i connect on the pc, but i have a tool for blank-flash the bootloader and make im work again, seems the tool directly writes the emmc
Click to expand...
Click to collapse
So, is your phone dead, or you recovered it?

tatazeuz said:
So, is your phone dead, or you recovered it?
Click to expand...
Click to collapse
I can recover with a tool from moto, because the phone doesnt turn on and only have a "special qualcomm download mode"
Enviado desde mi XT1032 mediante Tapatalk

tatazeuz said:
So, is your phone dead, or you recovered it?
Click to expand...
Click to collapse
Boss442 said:
I can recover with a tool from moto, because the phone doesnt turn on and only have a "special qualcomm download mode"
Enviado desde mi XT1032 mediante Tapatalk
Click to expand...
Click to collapse
O sea, sigue muerto? Ya lo intentaste recuperar?
So, its still dead? Did you already tried to recover it?

tatazeuz said:
O sea, sigue muerto? Ya lo intentaste recuperar?
So, its still dead? Did you already tried to recover it?
Click to expand...
Click to collapse
Ya esta recuperado, con una herramienta que escribe directamente en la eMMC del dispositivo y los drivers de la Riffbox.
Is already recovered, with a tool what directly writes the eMMC and the Riffbox drivers. Maybe later make a post

Boss442 said:
Ya esta recuperado, con una herramienta que escribe directamente en la eMMC del dispositivo y los drivers de la Riffbox.
Is already recovered, with a tool what directly writes the eMMC and the Riffbox drivers. Maybe later make a post
Click to expand...
Click to collapse
Definitivamente deberías compartir la herramienta, podrías salvar muchos Moto G en el futuro. Me hace sentir mas tranquilo que puedes reflashear un bootloader corrupto.
You should definitely share that tool, you could save a lot of Moto G's in the future. I feel a lot better knowing that you can reflash a corrupt bootloader

cancheritos said:
hi, i'm sorry, but i need help urgently. I unlocked the bootloader and flashed an international firmware so i can update to 4.4.2, since kitkat is not available in my country yet. then i tried to root my phone using superboot-windows.bat, and when the phone restarted it showd the moto logo, but it faded to black. so i turned it off, but now it doesn't turn on. is there a way to turn it on via adb or fastboot from windows?
please help i'm panicking.
Click to expand...
Click to collapse
If you read this thread you can reflash and ota to 4.4 then root, it contains everything you need,use the cooptx root method when your on KitKat,its the UK ROM but its the same as all other ROMs. Use the link to modaco to flash back to complete stock 4.3 then upgrade to KitKat ota the ln root , read the thread it has everything you need
http://forum.xda-developers.com/showthread.php?t=2616362

Boss442 said:
Sorry but the other day i kill the bootloader, i flash the .mbn files on the firmware and my phone don't work, only appears qusb-bulk when i connect on the pc, but i have a tool for blank-flash the bootloader and make im work again, seems the tool directly writes the emmc
Click to expand...
Click to collapse
Could you share this tool, please? I think I kill the bootloader too. After I did a command from terminal emulator (I’m using CM11), my Moto G shutdown and now it doesn’t power on… I tried a lot of “solutions”, but nothing can make it power on again…

danilocps87 said:
Could you share this tool, please? I think I kill the bootloader too. After I did a command from terminal emulator (I’m using CM11), my Moto G shutdown and now it doesn’t power on… I tried a lot of “solutions”, but nothing can make it power on again…
Click to expand...
Click to collapse
I do a post on original development
Enviado desde mi Moto G mediante Tapatalk

Boss442 said:
I do a post on original development
Enviado desde mi Moto G mediante Tapatalk
Click to expand...
Click to collapse
Ok. I found it.
I'm trying on a pc with Windows XP, but I can't install the Riffbox drivers... I'll try on a pc running Windows 8 soon. Is there any tip to install the drivers on Windows XP?

PLEASE HELP. MY POCOF2PRO DIED. It does not enter recovery or fastboot.

I hope someone can help me,
The other day I tried to install the rom.eu, but I got an error in recovery, what I did was wipe it and restart to try again to flash the rom with miui.eu. But oh surprise! It no longer turned on, it stayed dead, and when it was connected to the computer it only turned its led red but it did not recognize it, not even to revive with fastboot.
Investigating I found the "Deep Flash Cable" method, I did exactly everything but my pc does not recognize the phone anyway, so I can flash it with my flash. Someone please help me, do I need another specific driver for that?
Is there another way to revive my phone?
Thank you for reading.
SOLVED !!
The solution is in answer # 5:
PLEASE HELP. MY POCOF2PRO DIED. It does not enter recovery or fastboot.
I hope someone can help me, The other day I tried to install the rom.eu, but I got an error in recovery, what I did was wipe it and restart to try again to flash the rom with miui.eu. But oh surprise! It no longer turned on, it stayed dead, and...
forum.xda-developers.com

Poldark Hkenny said:
I hope someone can help me,
The other day I tried to install the rom.eu, but I got an error in recovery, what I did was wipe it and restart to try again to flash the rom with miui.eu. But oh surprise! It no longer turned on, it stayed dead, and when it was connected to the computer it only turned its led red but it did not recognize it, not even to revive with fastboot.
Investigating I found the "Deep Flash Cable" method, I did exactly everything but my pc does not recognize the phone anyway, so I can flash it with my flash. Someone please help me, do I need another specific driver for that?
Is there another way to revive my phone?
Thank you for reading.
Click to expand...
Click to collapse
Which twrp did you use?
With this method (EDL) you will need to use the Xiaomi Flash tool software (with qualcomm drivers) and the authorization to flash the rom. Only xiaomi repair centers and some developers have this authorization.
Try to charge it to 100% and to enter fastboot mode you will be able to flash with Miflash tool.

NOSS8 said:
¿Qué twrp usaste?
Con este método (EDL) necesitarás utilizar el software de la herramienta Xiaomi Flash (con controladores qualcomm)y la autorización para flashear la rom. Solo los centros de reparación de Xiaomi y algunos desarrolladores tienen esta autorización.
Trate de cargarlo al 100% y para entrar en modo fastboot usted será capaz de parpadear con la herramienta Miflash.
Click to expand...
Click to collapse
Thank you very much for answering.
Use the only one there is at the moment (I think so): https://forum.xda-developers.com/t/...l-twrp-poco-f2-pro-redmi-k30-pro-lmi.4241707/
I discard the battery since the phone was 100% when I used twrp but I still put it to charge and it still does not turn on and does not enter recovery or fastboot mode.

Poldark Hkenny said:
Thank you very much for answering.
Use the only one there is at the moment (I think so): https://forum.xda-developers.com/t/...l-twrp-poco-f2-pro-redmi-k30-pro-lmi.4241707/
I discard the battery since the phone was 100% when I used twrp but I still put it to charge and it still does not turn on and does not enter recovery or fastboot mode.
Click to expand...
Click to collapse
The TWRP you used is in development.
This onehttps://androidfilehost.com/?fid=17248734326145679747 is stable unfortunately too late.

maybe the solution https://forum.xda-developers.com/t/poco-f2-pro-bootloop-bootloader-locked.4235445/post-84516371

NOSS8 said:
maybe the solution https://forum.xda-developers.com/t/poco-f2-pro-bootloop-bootloader-locked.4235445/post-84516371
Click to expand...
Click to collapse
I was able to uncover the phone and enter EDL test point, I already connect to my computer at com 9008, but when flashing with my flash it asks me for EDL AUTHENTICATION.
Please, how can I solve that problem, can any XDA user help me with EDL AUTHENTICATION please?
Edit: already solved my problem. And thanks for your help anyway.

Poldark Hkenny said:
I was able to uncover the phone and enter EDL test point, I already connect to my computer at com 9008, but when flashing with my flash it asks me for EDL AUTHENTICATION.
Please, how can I solve that problem, can any XDA user help me with EDL AUTHENTICATION please?
Edit: already solved my problem. And thanks for your help anyway.
Click to expand...
Click to collapse
could you share the solution?

NOSS8 said:
could you share the solution?
Click to expand...
Click to collapse
Yeah right.
I contacted a staff that has EDL AUTH.
You should have everything ready:
OPEN PHONE READY TO TESTPOINT, ROM FASTBOOT, install TEAMVIEWER, and give the staff your TeamViewer id and password. Ready, he will do the rest.
Edit: You are going to have to deposit money to the staff.

Poldark Hkenny said:
Yeah right.
I contacted a staff that has EDL AUTH.
You should have everything ready:
OPEN PHONE READY TO TESTPOINT, ROM FASTBOOT, install TEAMVIEWER, and give the staff your TeamViewer id and password. Ready, he will do the rest.
Edit: You are going to have to deposit money to the staff.
Click to expand...
Click to collapse
Ok, the solution provided in post #5.

NOSS8 said:
Ok, la solución proporcionada en post #5.
Click to expand...
Click to collapse
Exactly.

Poldark Hkenny said:
Exactly.
Click to expand...
Click to collapse
I asked the question in case you had to find another solution.

Poldark Hkenny said:
Yeah right.
I contacted a staff that has EDL AUTH.
You should have everything ready:
OPEN PHONE READY TO TESTPOINT, ROM FASTBOOT, install TEAMVIEWER, and give the staff your TeamViewer id and password. Ready, he will do the rest.
Edit: You are going to have to deposit money to the staff.
Click to expand...
Click to collapse
Hello can you PM where did you hire someone to do it via teamviewer?

I'm having problems with my infinix zero 8

I tried for a gsi ROM and now my phone won't turn on and the sp flash doesn't work could someone help me?

Witcher rr said:
I tried for a gsi ROM and now my phone won't turn on and the sp flash doesn't work could someone help me?
Click to expand...
Click to collapse
Not much descriptive: "sp flash doesn't work", anyway you want to read this: https://www.xda-developers.com/bypass-mediatek-sp-flash-tool-authentication-requirement/

SubwayChamp said:
Not much descriptive: "sp flash doesn't work", anyway you want to read this: https://www.xda-developers.com/bypass-mediatek-sp-flash-tool-authentication-requirement/
Click to expand...
Click to collapse
when I go to put the stock rom file it says that the file is not compatible

Witcher rr said:
when I go to put the stock rom file it says that the file is not compatible
Click to expand...
Click to collapse
Then download the exact version that is for your device, add some screenshots here, also I guess you backed up something.

SubwayChamp said:
Then download the exact version that is for your device, add some screenshots here, also I guess you backed up something.
Click to expand...
Click to collapse
I already downloaded the version for my cell phone not I understand why you won't

Witcher rr said:
I already downloaded the version for my cell phone not I understand why you won't
Click to expand...
Click to collapse
It's hard, someone can help you without important info. You need to share some things like:
- How did you try to flash that GSI? Using which method?
- Is your device unlocked?
- I mentioned previously something like a backup, what about?
- If you are trying to flash the same version that was already onto your device (a downgrade is not allowed)
- If you really put the device in download mode?
- In SP Flash tool, which option you are trying? And if the tool detected device?
- How is your device listed in device manager from Windows PC?
- What exactly the message from SP Flash tool was?

SubwayChamp said:
It's hard, someone can help you without important info. You need to share some things like:
- How did you try to flash that GSI? Using which method?
- Is your device unlocked?
- I mentioned previously something like a backup, what about?
- If you are trying to flash the same version that was already onto your device (a downgrade is not allowed)
- If you really put the device in download mode?
- In SP Flash tool, which option you are trying? And if the tool detected device?
- How is your device listed in device manager from Windows PC?
- What exactly the message from SP Flash tool was?
Click to expand...
Click to collapse
I managed to fix the sp flash but I can't put the cell phone in download mode because I put the twrp what do I do??

Witcher rr said:
I managed to fix the sp flash but I can't put the cell phone in download mode because I put the twrp what do I do??
Click to expand...
Click to collapse
Usually download mode works with device off and connecting to the PC, TWRP doesn't matter here, you have to read a sound that reveals if PC is detecting and then if you tap on download option in SP Flash tool and connect device you will see the progressing bar down.

SubwayChamp said:
Normalmente o modo de download funciona com o dispositivo desligado e conectado ao PC, TWRP não importa aqui, você tem que ler um som que revela se o PC está detectando e então se você tocar na opção de download na ferramenta SP Flash e conectar o dispositivo, você verá a barra de progressão para baixo.
Click to expand...
Click to collapse
my cell phone doesn't turn off, it continues to fast start and gives an error

Witcher rr said:
meu celular não desliga, ele continua em inicialização rápida e dá um erro
Click to expand...
Click to collapse
English is required here.
To completely power off the device you should have to press the three buttons simultaneously per about 10 seconds and keep it connected to the PC, press the Download option in the tool in a way that while device power off at least for a second the tool will detect it, and it will proceed with the installation of the firmware.

SubwayChamp said:
O inglês é obrigatório aqui.
Para desligar completamente o dispositivo, você deve ter que pressionar os três botões simultaneamente por cerca de 10 segundos e mantê-lo conectado ao PC, pressione a opção Download na ferramenta de forma que enquanto o dispositivo estiver desligado por pelo menos um segundo a ferramenta irá detectá-lo e ele prosseguirá com a instalação do firmware.
Click to expand...
Click to collapse
thanks

SubwayChamp said:
English is required here.
To completely power off the device you should have to press the three buttons simultaneously per about 10 seconds and keep it connected to the PC, press the Download option in the tool in a way that while device power off at least for a second the tool will detect it, and it will proceed with the installation of the firmware.
Click to expand...
Click to collapse
I'm facing the problem sp flash tool error status brom cmd send da fail​

Witcher rr said:
I'm facing the problem sp flash tool error status brom cmd send da fail​
Click to expand...
Click to collapse
Then you need this https://forum.xda-developers.com/t/...d-flash-in-edl-with-no-auth-for-free.4229683/ read carefully the thread, replace the files from the Redmi Note 9 for those that are for your device, if you do it correctly, for sure this will solve your issue.

SubwayChamp said:
Then you need this https://forum.xda-developers.com/t/...d-flash-in-edl-with-no-auth-for-free.4229683/ read carefully the thread, replace the files from the Redmi Note 9 for those that are for your device, if you do it correctly, for sure this will solve your issue.
Click to expand...
Click to collapse
thanks I'll try

SubwayChamp said:
Then you need this https://forum.xda-developers.com/t/...d-flash-in-edl-with-no-auth-for-free.4229683/ read carefully the thread, replace the files from the Redmi Note 9 for those that are for your device, if you do it correctly, for sure this will solve your issue.
Click to expand...
Click to collapse
I couldn't ): my computer didn't start python and everything I tried gave an error

Witcher rr said:
I couldn't ): my computer didn't start python and everything I tried gave an error
Click to expand...
Click to collapse
Well, you have there the solution, it's up to you keep it trying till you finally can achieve it, probably you need to uninstall Python and then reinstall it, probably you need even run it in other Windows version, maybe install Windows from fresh.
Other people could do it and my self I had solved the issue with my bricked RN9 so just depends to get it work from checking every part is needed on the process.

Ami
SubwayChamp said:
Well, you have there the solution, it's up to you keep it trying till you finally can achieve it, probably you need to uninstall Python and then reinstall it, probably you need even run it in other Windows version, maybe install Windows from fresh.
Other people could do it and my self I had solved the issue with my bricked RN9 so just depends to get it work from checking every part is needed on the process.
Click to expand...
Click to collapse
And I won't be able to because my computer is windows 7): But my cell phone has the pitch Black, will it be possible to put a gsi on it??

Witcher rr said:
Ami
And I won't be able to because my computer is windows 7):
Click to expand...
Click to collapse
probably it works too on W7.
Witcher rr said:
But my cell phone has the pitch Black, will it be possible to put a gsi on it??
Click to expand...
Click to collapse
If your device can enter to fastboot and its bootloader is unlocked you can, you also should need the USB debugging to have enabled.

SubwayChamp said:
probably it works too on W7.
If your device can enter to fastboot and its bootloader is unlocked you can, you also should need the USB debugging to have enabled.
Click to expand...
Click to collapse
I already managed to put the Black pitch but I don't know how to put a gsi

Witcher rr said:
I already managed to put the Black pitch but I don't know how to put a gsi
Click to expand...
Click to collapse
I even put one but the cell phone won't turn on

Question hard unbrick poco x4 pro

Hi, I need to know if someone knows how to unbrick (hard brick) the x4 pro. After the update it died. it is only recognized as Qualcomm HS-USB QDLoader 9008 via usb. thanks alot!!!
Nico

nordoqui said:
Hi, I need to know if someone knows how to unbrick (hard brick) the x4 pro. After the update it died. it is only recognized as Qualcomm HS-USB QDLoader 9008 via usb. thanks alot!!!
Nico
Click to expand...
Click to collapse
Hello,
bootloader is unlocked?

Fedon said:
Hello,
bootloader is unlocked?
Click to expand...
Click to collapse
Hello, unfortunately it is blocked.
I was able to access the fasboot and the assistance mode through pcsuite but it does not recognize it, neither does the xiaomiflash. I'm trying to do it through adb, but I can't find the steps, thanks

As i say to other member...
I mean its end for your phone.
I dont found working solution :/

Fedon said:
As i say to other member...
I mean its end for your phone.
I dont found working solution :/
Click to expand...
Click to collapse
I must tell you that the problem (mine) is that in order to turn it on you have to press on the back at the height of the lower cameras or where it says 108 mp. BY DOING THIS THE PHONE SWITCHED ON NORMALLY. since yesterday the phone works normally, so if someone has a cell phone that has frozen the screen and died, try. I did it with a roll of hard paper (make pressure). I hope it helps someone.
y gracias a esta comunidad por tener gente siempre dispuesta a solucionar problemas. (lo siento, es traductor de google)
PD: now we just have to see what the internal problem is

nordoqui said:
I must tell you that the problem (mine) is that in order to turn it on you have to press on the back at the height of the lower cameras or where it says 108 mp. BY DOING THIS THE PHONE SWITCHED ON NORMALLY. since yesterday the phone works normally, so if someone has a cell phone that has frozen the screen and died, try. I did it with a roll of hard paper (make pressure). I hope it helps someone.
y gracias a esta comunidad por tener gente siempre dispuesta a solucionar problemas. (lo siento, es traductor de google)
PD: now we just have to see what the internal problem is
Click to expand...
Click to collapse
How did u even figure out that u have to press at that specific spot? Can you record a video or something showing how to? Also does it boot normally now or you still have to press at that weird spot?

yash_patil2k5 said:
How did u even figure out that u have to press at that specific spot? Can you record a video or something showing how to? Also does it boot normally now or you still have to press at that weird spot?
Click to expand...
Click to collapse
I'm going to tell you.
the phone has about 2 months of use, over time it began to have problems, in different apk, camera, gallery until one day it died. I could only get it up through qualcomm, but no flashing tool could do the complete process to install the firmware again (believing that was the problem).
One day (here you will get to know my violent side) between connection and connection of the USB cable so that I could take the qualcomm, I hit it with my palm on the back of the phone at the height of the camera and it turned on but it turned off again and I could not pick it up. .. That got my attention. I kept trying by other means without hitting him again, but there was no way to get him up.
Yesterday, I put a roll of paper on the desk, put the phone on the roll at the height of the lower cameras and the phone picked up but turned off again, freezing as I have seen in several images of the little x3, then I put a bigger roll and in the upper part (front camera) I put weight on it, I put pressure on the lower part, so that it pressed well where it allowed me to lift the phone. Once it was up, I went straight to the configuration to be able to leave it in debugging and activate the oem unlock, in case it turned off again but so far it is not necessary, the phone has been on since yesterday and I have not had any problems yet, but it is clear that internally there are something lazy, I don't know what you think.
I can make you a video. Cheers,

Go

I have the new firmware 13.0.9.0
mmmm, download?