Related
Bonjour
I upgraded to WM6 (pdaviet) 2 months ago (I guess..), and problems started to appear a few weeks ago. First it just was hard to boot sometimes, had to reboot several times to get it up and running, but when it could start everything was fine. Then since yesterday, it became harder. And today, couldn't start it at all. Tried several times, and everytime the screen went melted, corrupted, like if it couldn't stand an o/c, but it always runs at normal speeds. I guess it has something to do with the battery and the way WM6 handles it (or at least the implementation we have on our prophet).
I tried to hard-reset, I left it a long time on the format screen (before the actual HR) and it handled it for long enough, but the same thing started while setting up WM.... too bad !
While writing this message I tought I could try to downgrade, and I did using AKU3.3-Jester-b1.
I had no problem while the phone was in guest mode after the HR.
Everything went nice during first step upgrade, but on final reset it did the same thing, and now..... it cannot start at all !!!!
Someone has an idea ? I own a G4 and it has the following roms :
IPL 2.10, SPL 2.20, GSM 2.47 (or something like that)
It won't charge (but my batteries are full, I've got an external charger), it won't start from battery nor from power, even if the battery is removed.
Damn, at least I guess I can return it like that to orange, since it cannot start one can't see the modified rom...
If anyone has a suggestion, it is more than welcome ^^
Thanks !
Niko
huh !
back to semi-life ^^
After a few hours left alone without battery or sim card, it started again...
but it still resets every few minutes, or the screen goes melted (actually its like white scanlines that fulfill the screen).
I'll try to leave it shutdown for the night, see if I can at least put the orange splash screens and rom back for warranty purpose.
But it now has serious HW problems, for sure. And my opinion is WM6 has something to do with that. BEWARE !
Another strange thing is that I now have to keep the reset button pressed for half a second to reset, where it reseted instantly before. Those devices really have unstable hardware.
FYI, it was almost brand new, as it was warranty-replaced about one week before I installed WM6.
lastnikita said:
back to semi-life ^^
After a few hours left alone without battery or sim card, it started again...
but it still resets every few minutes, or the screen goes melted (actually its like white scanlines that fulfill the screen).
I'll try to leave it shutdown for the night, see if I can at least put the orange splash screens and rom back for warranty purpose.
But it now has serious HW problems, for sure. And my opinion is WM6 has something to do with that. BEWARE !
Another strange thing is that I now have to keep the reset button pressed for half a second to reset, where it reseted instantly before. Those devices really have unstable hardware.
FYI, it was almost brand new, as it was warranty-replaced about one week before I installed WM6.
Click to expand...
Click to collapse
Hey LastNikita,
I had the same problem ! The white scanlines thing just after re-updating a WM6 version (pdaviet), because I was tired of the constant reset issue.. suddenly, the update went wrong, and I stupidly followed the "recovery" process, which tells u to remove the battery... bang ! screen went corrupted !
Like you, I tought it was over... but I noticed that if you connect your phone and PC with USB, and keep pressed power (ON/OFF button on side) + camera after reseting (little hole on bottom - press during 5 sec!), the PC recognizes a USB device (not the usual phone drivers...) at this moment, I launched the Jester 3.3 (step1) update, in order to downgrade from the ugly WM6 pdaviet... My phone was not yet fixed (still with white scanlines), but at least, I could hear again the WM "start" sound, the scanlines would also "move" across the screen borders when I touched the screen, which made me imagine I was on the calibrating process... also, while connected to PC, after a while, ActiveSync would launch, asking for 1st time synch... this kept me confident as the phone (software) seemed to be reacting fine although HW prob...
I completely charged the phone again (till green light) then kept on reseting the phone (until I hear the WM sound) hoping the lines would finish scanning and come back with the normal .. and guess what, it did !!! Of course, PIGHEAD as I am, I wasn't totally happy it recovered with WM5, so i digged for a better rom, and I can tell you I'm very happy with the smart1 (wizard version) which works fine, but still has some minor bugs as Live Messenger not working... but runs fine (specialy when pressing the ON/OFF button !
PS: Make sure the ALWAYS completely switch off your phone (ON/OFF for 3 secs) before removing the battery... it did happen again... when I stupidly trusted the "recovery" process, again !
DUHHHH !!!!
PS: at least, now you ALL know !
Kokiri
Finally ok for warranty )))
Thanks for sharing mate
I finally managed to downgrade to my original Orange rom, and I'm in the process of putting the original Orange splash screens back (I made the nk.nbf but I can't find the right utility to upgrade... "Update utility cannot open the requested file").
BUT I still have that HW problem afterall.... so I guess it still has to go back to warranty right ? This isn't a big deal since Orange is VERY prompt (I guess I'll get it tomorrow or monday morning, the delivery guy brings a new one and goes back wiv my phone, quite nice !), and I have a button which is stucked (from the begining) anyway ^^
While I'm writing this my phone is docked and synced, and it seems fine.... but, I guess, as soon as I will reset it will start over again.... I'll keep you posted.
Anyway, I'm no longer desesperate and that's good news (for me ^^)
++
niko
yip
ok, everything's back to original.
Actually, it works well when docked, but it freezes/melted screen as soon as I tried to use it on battery, so that I'm quite sure it has something to do wiv WM6.... I'll post that on some crossbow threads this weekend if I have time enough (there are so many of them now !)....
But once more, if YOU read this, keep that in mind.
Hope you guys won't have that kind of failure while trying it.
++
niko
confused
I am having the same problem except the screen showing white scanlines everything else is working on the handset. Could it be a LCD Problem?
Me too...
I have the same issue (black/colored vertical lines and a white screen). I think it has to do with upgrading to WM6 or with overclocking with batteryStatus, not sure. This are the suspects in my opinion....
Now I downgraded to WM5 but the problem seems to persist, I disabled batteryStatus and will see if the situation improves... crossing fingers
Uhm ... possible Overclocked!
I have read 3 threads with same errors!
how much was your highes clock? do you use it for navigation? long time on highest clock or only for speed up?
i dont have a problem with scan lines but with my prophet i use the scaling option and go max to 234 i also set to 234 when using certain apps.
is this damaging to my prophet?
at the moment trying to upgrade to PDAViet 4.0.0.0.3 with a world of pain but thats another topic!
I have a 4155 that has developed the following problem: most of the times it doesn't turn on correctly. I press the power button, I see the backlight coming on but the screen stays grey (blank). Eventually I can get it back on, but only after performing a hard reset, then many, many soft resets (anywhere between 10 and 30). Then it works again for a little while, and the whole thing happens again.
The only way to avoid it is to have the screen stay on all the time, i.e. keep it plugged in and have it not turn off while on AC. If I allow the screen to turn off, chances are I'll have to do the whole reset procedure again, and it takes up to 30 minutes each time. It doesn't matter at all how well charged the battery is, and it even does it if I allow the screen to turn off while plugged in.
Of course in its present state it's just a little more than a paperwewight, not a PDA. I know that underneath it works correctly, just the display has this weird bug. I opened it up and poked inside, put it back together - no change. Does anyone have any idea? I'd really, really like to make this work again.
Thanks for any help!
(I should mention that I flashed the ROM once: I got it cheap off eBay because it was the French language version, and I flashed it with the English ROM. Worked like a charm for many months, then it developed the problem above. Don't think it's related to flashing, but thought I'd mention it anyway)
Bump. .
Hey guys,
Oh i dunno whays happened. Everything worked fine yesterday then i went to sleep. Next day the side buttons stopped working. The touch screen still works but the side capacitive buttons stopped.
It doesnt even work when i boot into clockwork mod
I have so far tried:
Reboot did nothing
Put calibration.ini file in root directory
Put calibration.ini in sdcard2
Put calibration in sdcard root
Reboot
Didnt fix it.
I got it ebay as i live in australia so warranty may be difficult.
I am using button saviour to get by for now but until i can get the side buttons to work i can no longer navigate clockwork mod because the home button is the select button.
I'm usibg vegantab b5.1 at the moment.
Any help would be really appreciated!
BAM
If you haven't, you might want to try this: http://forum.xda-developers.com/showthread.php?t=934500
Just tried it but still no joy. Looks like the side buttons are on a different touch interface to the rest of the screen. I guess it could be worse. Vegantab is a nice rom to be stuck on.
I wonder if there is a way to make clockwork mod work with a usb keyboard?
Woohoo! It's working again! Just in time for honeycomb too
I searched and searched for similar issues and finally read about either draining the battery or opening up to find the hidden reset button.
I opted to drain the battery.
Now I'm still not going to rubber stamp that draining the battery fixed it but when I did finally plug it in and fire it up I found the buttons worked again.
Another theory I have is that viewsonic might have some poor soldering. The reason I suggest that is because in Australia we've had some stinkin hot days here at 42degrees Celsius with high humidity. So it wouldn't surprise me for a dry solder to become temperamental under these conditions.
Anyways happy ending for now. Well hopefully it'll keep running until a reliable honeycomb rom turns up for gtab hey
I have encountered a similar problem. The side buttons stopped working after a few days of use. They do work sometimes randomly. Is there a reliable solution to this problem?
I tried calibration.ini, and the buttons worked once. They have stopped working again.
Hi guys
I have this strange behavior going on in my Sentation.
Out of nowhere my phone started to have strange screen behavior... Didn't light up after pressing the power button (had to phone my self in order to get screen on).
The next thing was that suddenly the screen goes to maximum brightness or goes to minimum without any explanation (tried both auto brightness or manual).
After that I noticed that the screen went off when I was using it but when I pressed the left side of it it lighted up and off again... making me think of some kind of bad contact underneath. As I already had changed a broken touch screen for t3 times, and let the phone fall for several times I thought it had to do with some plug out of line...
I disassembled the phone completely and mounted up back again. The thing is that the phone started to freeze every 5 minutes (screen on but completely freezed. I have to pul out battery). Sometimes it freezes even in the recovery menu. I've tried several rom's with full wipe and not installing anything and its all the same.
Some times I still not that the screen goes off during the freeze but when I touch the left side it goes on again, but that doesn't change the freezed state even that I let down the phone for several minutes.
I disassemble the phone again, tried different back cover and different battery (one stock and other extra strength) I tried also all the suggestion related to the small pin in the back not connecting well with the back cover (adding an aluminium foil, pulling the pin out, etc..)
Nothing seams to resolve anything so I have clearly an hardware problem... but I don't know what to replace or where to look the damage!!!
Can anybody help me please?!
Update
I have an update on my problem:
I noticed that when I leave the phone on top of some kind of metal part and don't touch it it works all day without any problem but, as soon as I start to touch the phone, it freezes within minutes!
Could it be some kind of static electrical problem? How to resolve it?
I would apreciate any help
Thanks
My z-flip3 5g has a strange problem. If i close it (by folding the screen closed), then after opening (unfolding) the screen and touching the right side button/fingerprint reader to unlock it, i hear the quiet "click" noise that indicates the phone is unlocked, but the screen stays black. i then have to repeatedly push the lock button on the right to lock the phone again and unlock it again. after several attempts the screen finally turns on. sometimes it will go black a few seconds later and the same issue continues. but other times the screen will stay on and work fine.
i have noticed that if i do not close the phone (folding the screen together) then i do NOT encounter this issue. the phone screen turns on when pushing the right side button (or touching the fingerprint sensor) and everything works fine.
this issue started yesterday, a system update installed yesterday as well, could it be related?
i already restarted many times, booted into recovery mode and wiped the cache. nothing has helped. the only way to avoid the problem is by not closing (folding the screen shut) the phone.
One UI v 5.1
Android 13
Security patch level Feb 1, 2023
fully stock/not rooted
I have same behavior. Did you solve this problem?
Unfortunately no. Did a factory reset, hoping that would help, but the issue persists
Mine has recently started doing the same. Last update was right before this started several weeks ago. I don't have mine set to require fingerprint, it should just turn on after opening. If I open it partway, it will turn on, then turn back off when fully opened.
hi,
i have same problem, it's software problem?
Not completely sure about that. They update this thing so often, it could be coincedence that it started shortly after an update. I want to try blowing out the hinges as I've got some dust under there that I hear when opening the phone. Definitely not a phone to put in your pocket after working in the wood shop!
Digital Dragon said:
Not completely sure about that. They update this thing so often, it could be coincedence that it started shortly after an update. I want to try blowing out the hinges as I've got some dust under there that I hear when opening the phone. Definitely not a phone to put in your pocket after working in the wood shop!
Click to expand...
Click to collapse
and don´t take it to the beach either!
What is also strange is that when I close the phone and open it a few seconds later, there is no issues whatsoever. However, if I leave it closed a few minutes, then when opening it, the problems with the screen staying off happen.
Yes, definitely don't take it to the beach!
@netridah , mine is doing exactly that. Which makes me wonder is it a wake issue, or a mechanical/sensor issue with the hinge.
one more to the bill
I checked the flexes and I warmed up the logic nothing works
I have the same issue: Flip 3 - 5G with OneUI 5.1 - 1 April Patch level
When I open the phone I eventually see for less than one second the lock screen, the goes black and unresponsive.
Then I have to press the button to turn the screen off (even if it is already) and then re-press the button or use the fingerprint to turn it on and it will work (eventually, sometime I have to do it a couple of times).
I already googled it on many forums but no solutions, I've tried to:
Disable the always-on display - no result, at first looked like it did the trick but the day after was having the same issue.
Check all the updates of the system components like always on-on display (settings --> lock screen --> always on display --> info), no help everything is up to date.
Hi,
I have the exact same problem, only difference is that I'm on the z flip 4.
I get the black screen and sometimes when opening or closing the phone the screen can flash in a bright yellow or green color.
I got a motherboard but the problem continued
Next step changing screen is very expensive at the moment
This is driving me crazy - also started the day I updated to OneUI 5.1.
Hoping for a solution soon!
I am also encountering this problem, I went to samsung repair shop 1 month out of warranty, sales person said it is a screen issue and needs to be replaced for 430$. Mine was before the update, i took mine near the pool, got wet maybe, as the alarm for usb charging mentioned unplug it immediately, day after it began randomly dark when phone is openned fully. Zflip 3
Oh just an update, i did some tinkering today, Good lock all updated, disabled clockface, sprayed some contact cleaner on power button, and hinges, fold close and open for a minute or two, fell asleep for 1 hour, and when I woke up, my screen works back to normal, it wakes up when unfolded, no more waiting or hitting the power button several times. hope this stays like this.
piper_indebt said:
Oh just an update, i did some tinkering today, Good lock all updated, disabled clockface, sprayed some contact cleaner on power button, and hinges, fold close and open for a minute or two, fell asleep for 1 hour, and when I woke up, my screen works back to normal, it wakes up when unfolded, no more waiting or hitting the power button several times. hope this stays like this.
Click to expand...
Click to collapse
How to disable the clockface? what would that contact cleaner be?
thanks
firstchris said:
How to disable the clockface? what would that contact cleaner be?
thanks
Click to expand...
Click to collapse
Hi, few days now, I still have occasional blacking out, I've tried putting my phone on safe mode, and this seems to solve the problem. I suspect it may not be hardware fault, but 3rd party software, "good lock" or something else that conflicts wit one ui, that makes the flipping open lag waking up. Contact cleaner used for electrical stuff
Didnt use my z3 for about a week let the battery drain.. then charged it too 100% without turning on the phone.. my phone back to normal now.. hope it works for you guys
Hello,
I am using Z Flip 4 and last night I started having this problem as well. I can confirm 100% that my phone has no hardware nor a history of impact of any sort that's why it's really frustrating having this kind of problem.
Has anyone already found a resolution for this problem?
Z flip 4 here also. Had the same problem with the screen. Took the phone to Samsung and they changed the screen, frame and back panel's for free under warranty.
They said it's a hardware issue.
So better to take the phone to Samsung.