hi all
help me please , i was using ADB to turn the S-ON , the phone restarted and never came back ....
even when i press the start button nothing happens , i tried the press sound down and open ... nothing
i tried to connect it to the pc , nothing , please help me as HTC EGYPT say they dont have the sw to fix it and wants to replce the motherboard !!!!!
Does your PC detect phone? Try writing command "adb devices", if not try to remove battery and let it for 5minutes and try again, also was your battery full charged before you tryed this?Try let it charge a bit if none of above helps.
But if nothing of that helps i dont see what else could you do..its dead and you need to service it..
nope , ADB doesn't detect it
Before you did the command for S-On did you flash back to stock with the original RUU that came with the phone?
You have corrupted your device and are now in QHSUSB download mode (used by Qualcomm to flash drivers and such to the cpu) and yes you are bricked.
ouch. that sucks lol
Look at the bright side of things. Use this as a learning experience. Now you know what NOT to do with your phone the next time.
Sent From My Pocket
then since i am offically bricked , what is the way out
nope i didnt i did these steps
6.enter the command "fastboot oem writesecureflag 3" (Thanks Dazweeja)
7. Reboot into bootloader using "fastboot reboot-bootloader" or remove & reinsert the battery and press power on while keeping hold of volume down.
ehaballam said:
then since i am offically bricked , what is the way out
Click to expand...
Click to collapse
Call your carrier or HTC and hope they take pity on you, but you'll likely be on the hook for this one.
Related
So I've been trying try to install ARHD, and in the process, I went to boot my phone into bootloader.
Cue, phone not turning on.
Hold down the power button, nothing
Hold down the power+vol down, nothing.
The only glimmer of hope is that when I plug it in, windows says "Hey, there's a device here!" But I think that could just be the generic sound it plays when it realises something is plugged in, whether it works, or not.
I apologise for making *another* brick thread, but it seems most of the "bricked" threads I could find say "My phone just has infinite boot animation, am I bricked? :<" or things similar.
If there's any way, any way at all, to fix this, I would be... appreciative, to say the least.
Prior to possible brickage -
I was following this which in turn linked me to this, I got to "7. enter the command "adb reboot-bootloader". (nothing further required device WILL reboot in bootloader)"
That's it. Nothing else, other than the build up to it, such as plugging it in and moving the files to the C drive and such and such. And then I just did "adb reboot-bootloader", and... it didn't like it.
Any way to undo a brick if I am, or is it completely dead? Off to the phone graveyard?
Thanks in advance.
Valk
Valkorian said:
So I've been trying try to install ARHD, and in the process, I went to boot my phone into bootloader.
Cue, phone not turning on.
Hold down the power button, nothing
Hold down the power+vol down, nothing.
The only glimmer of hope is that when I plug it in, windows says "Hey, there's a device here!" But I think that could just be the generic sound it plays when it realises something is plugged in, whether it works, or not.
I apologise for making *another* brick thread, but it seems most of the "bricked" threads I could find say "My phone just has infinite boot animation, am I bricked? :<" or things similar.
If there's any way, any way at all, to fix this, I would be... appreciative, to say the least.
Prior to possible brickage -
I was following this which in turn linked me to this, I got to "7. enter the command "adb reboot-bootloader". (nothing further required device WILL reboot in bootloader)"
That's it. Nothing else, other than the build up to it, such as plugging it in and moving the files to the C drive and such and such. And then I just did "adb reboot-bootloader", and... it didn't like it.
Any way to undo a brick if I am, or is it completely dead? Off to the phone graveyard?
Thanks in advance.
Valk
Click to expand...
Click to collapse
of all things you tried i think you havent tried this
can you try it and reply
rebooting to bootloader manually:
To reboot to bootloader remove your battery, reinsert, hold volume down and press power button. Do not release Vol down until booted into bootloader
if you got into bootloader and then your phone is not bricked..you can bring back your mobile to life completely
if that didnt helped you..click on IRC HELP CHANNEL in my signature and join it and express your grievance there ?
ganeshp said:
To reboot to bootloader remove your battery, reinsert, hold volume down and press power button. Do not release Vol down until booted into bootloader
Click to expand...
Click to collapse
Doesn't look like that worked. I shall go and have a look at the channel now, thanks anyway.
Valkorian said:
Doesn't look like that worked. I shall go and have a look at the channel now, thanks anyway.
Click to expand...
Click to collapse
Helo try to connect all the pins in the phone (battery place) for 10 seconds at least with power button pressed without battery then try to start it again
Good luck
Hey if its still not working just use the emmc_recover method to fix hboot.
http://forum.xda-developers.com/showthread.php?t=1522351"
follow these steps to fix it. I had the same problem and fix it with this method but please search for the revolutionary 1.27.1100 hboot whicht is s-off from here http://forum.xda-developers.com/showthread.php?t=1459767 use the one from the 32.xxx firmware and all should be fine
Would the RUU help ?..
Hey !
I had something similar happen to me. Since Windows could see the device, I tried flashing a stock RUU (...) .exe from it and... back to life it came !
Good luck !
quietmoth said:
Hey !
I had something similar happen to me. Since Windows could see the device, I tried flashing a stock RUU (...) .exe from it and... back to life it came !
Good luck !
Click to expand...
Click to collapse
Something like this, since windows is finding it, you may be able to reset it into bootload through ADB.
"ADB reboot bootloader"
If you can get that, you can get back into recovery.
Sent from my Sensational LeeDroid Beater.
PHONE STATUS
MODEL SENSATION XE
WARRANTY YES (in warranty)
S-OFF/ON OFF
Rooted YES
SUPPER CID YES (I Know the original CID)
RECOVERY Installed
PROBLEM SCREEN DEAD
REQUIREMENT Want to restore original status (S-ON, Unroot, original CID, Relock the bootloader, remove recovery etc.) for warranty claim.
DESCRIPTION:
Well screen is completely dead, it displays nothing but a whitish backlite, I can hear startup up sound and touch sounds, can also receive calls, power button and bottom buttons are working normally but display is dead for sure.
Yesterday i successfully restored the Original RUU (I can hear the new staurtup sound), now I cannot detect my phone in Adb list (maybe debugging mode is OFF) neither I am able to start it in boot loader. HELP REQUIRED BEYOND THIS.
there was a similar thread by another person long back..do a search for it ..i have given detailed instructions there
hmm it seems like you did done the ruu thing
now you need to go to bootloader ...
remove battery ..reinsert it... then press power button + voulme down together ..after some time you will get a small vibration ..then connect the phone to pc
there fastboot works
you can check it using
fastboot devices command
then use the fastboot to restore the cid to original one
fastboot oem writecid xxxx
then do the SON finally but before that ..check all the existing details of the phone using
fastboot getvar all (post it here except imei so that i can verify them...)
then atlast
fastboot oem writesecureflag 3
ganeshp said:
now you need to go to bootloader ...
remove battery ..reinsert it... then press power button + voulme down together ..after some time you will get a small vibration ..then connect the phone to pc
[/B]
Click to expand...
Click to collapse
it tried it about 20 times but phone is booting to OS (i can listen startup sound after viberation) instead of bootload.
makhane said:
it tried it about 20 times but phone is booting to OS (i can listen startup sound after viberation) instead of bootload.
Click to expand...
Click to collapse
removing battery and reinserting the battey is the main part ..are you doing it ?
also while the phone is trying to boot...type "fastboot devices" and then see whether the device is being shown or not
if not showing ..press power button once ....then try fastboot devices again
ganeshp said:
removing battery and reinserting the battey is the main part ..are you doing it ?
also while the phone is trying to boot...type "fastboot devices" and then see whether the device is being shown or not
if not showing ..press power button once ....then try fastboot devices again
Click to expand...
Click to collapse
well something else worked for me, i ran the RUU.exe while it starts searching the phone, i got it listed under "adb devices"
Now i'hve PM you all the detials (bit too many), please review them and reply.
Thanks
K got this HTC from a friend of me, was working before, had it rooted and fixed with custom rom
It was S-on on v1.27
k now gonna try to explain what's going wrong:
When i shut down the phone, put battery out, back in, connect to usb, i get the phone recognized by ADB (my HTC phone)
when i type adb reboot-bootloader, device responds and boots into fastboot mode
when i use vul up i get Fastboot usb on screen
from this point i can't get any further, device doesnt respond from any button action except for vol up.
Device is not recongized in windows now (windows 8 64bit) got the famous error 43
So in ADB everything is fine, but in fastboot nothing is working/responding
when i pull battery out, then put it back in, i can succesfully boot with volup en power, then i get everything running (custom rom from before) but it says safe mode
Any ideas what i can do to get this thing back on it's feet?
regards,
Robin
robin-sips said:
K got this HTC from a friend of me, was working before, had it rooted and fixed with custom rom
It was S-on on v1.27
k now gonna try to explain what's going wrong:
When i shut down the phone, put battery out, back in, connect to usb, i get the phone recognized by ADB (my HTC phone)
when i type adb reboot-bootloader, device responds and boots into fastboot mode
when i use vul up i get Fastboot usb on screen
from this point i can't get any further, device doesnt respond from any button action except for vol up.
Device is not recongized in windows now (windows 8 64bit) got the famous error 43
So in ADB everything is fine, but in fastboot nothing is working/responding
when i pull battery out, then put it back in, i can succesfully boot with volup en power, then i get everything running (custom rom from before) but it says safe mode
Any ideas what i can do to get this thing back on it's feet?
regards,
Robin
Click to expand...
Click to collapse
In bootloader(fastboot mode) no buttons will works except vol up,down and power..
If you want to flash a custom rom then
First goto bootloader
Now enter to recovery by using vol down and then power button to ok.
Place a Rom.zip in sdcard format cache/dalvik , all partition except sd and then flash rom..
ahsan64 said:
In bootloader(fastboot mode) no buttons will works except vol up,down and power..
If you want to flash a custom rom then
First goto bootloader
Now enter to recovery by using vol down and then power button to ok.
Place a Rom.zip in sdcard format cache/dalvik , all partition except sd and then flash rom..
Click to expand...
Click to collapse
problem was that none of the button's where responsive, i found the cause of this, volume buttons are damaged (the strip inside was broken)
So now i have a new problem much wurse i think
only power button works, so i did a complete reinstall with ruu, booted up fine, but always in safe mode for some strange reason,
Now after shutdown, i can't get the phone on anymore, only goes to Hboot, and there is nothing responsive, non eof the buttons work, can't use vol buttons because they are broken.
Adb is not responding either, only getting HTC Android USB device in my device list....
I think the phone is ready for trash? :S
robin-sips said:
problem was that none of the button's where responsive, i found the cause of this, volume buttons are damaged (the strip inside was broken)
So now i have a new problem much wurse i think
only power button works, so i did a complete reinstall with ruu, booted up fine, but always in safe mode for some strange reason,
Now after shutdown, i can't get the phone on anymore, only goes to Hboot, and there is nothing responsive, non eof the buttons work, can't use vol buttons because they are broken.
Adb is not responding either, only getting HTC Android USB device in my device list....
I think the phone is ready for trash? :S
Click to expand...
Click to collapse
in bootloader adb doesn't work only fastboot
so when you are in hboot screen try this command
fastboot reboot (in the hboot screen should say fastboot usb)
rzr86 said:
in bootloader adb doesn't work only fastboot
so when you are in hboot screen try this command
fastboot reboot (in the hboot screen should say fastboot usb)
Click to expand...
Click to collapse
can't get into adb anymore so i think the phone is dead unless we repair the volume buttons right?
robin-sips said:
can't get into adb anymore so i think the phone is dead unless we repair the volume buttons right?
Click to expand...
Click to collapse
since you are dealing with a hardware problem then yes
but try this
boot normally(even on safe mode)
connect it to pc and type
adb reboot bootloader
it will take you directly into fastboot mode
then type fastboot reboot
see how it goes and check volume button from there(to confirm the hardware issue)
otherwise repeat the procedure but instead of fastboot reboot run the ruu.exe again
Hey Guys I was flashed my i9003 (with partition) because i have 2 partition, and i wanted to combine the two partition, but my phone is dead
no mode download , no recovery , no boot ! i searched for get any solution i found two ways , change mainboard or use JTAG / riff BOX
but i can't do them ! have you got another solution please
botter75 said:
Hey Guys I was flashed my i9003 (with partition) because i have 2 partition, and i wanted to combine the two partition, but my phone is dead
no mode download , no recovery , no boot ! i searched for get any solution i found two ways , change mainboard or use JTAG / riff BOX
but i can't do them ! have you got another solution please
Click to expand...
Click to collapse
did you tried with FASTBOOT? it's the only thing that maybe can work for you but it's not easy. when you turn it on, does the screen light up (even in a very subtle way)? beacuse if it doesn't i'm afraid there isn't much to do.
but how Can do FASTBOOT + My Phone => No Boot ; No Mode Download ; no Recovery , But when i connect is with me Computer ; My computer seach Drivermap 3630
Articadrake said:
did you tried with FASTBOOT? it's the only thing that maybe can work for you but it's not easy. when you turn it on, does the screen light up (even in a very subtle way)? beacuse if it doesn't i'm afraid there isn't much to do.
Click to expand...
Click to collapse
botter75 said:
but how Can do FASTBOOT + My Phone => No Boot ; No Mode Download ; no Recovery , But when i connect is with me Computer ; My computer seach Drivermap 3630
Click to expand...
Click to collapse
Then i dont know how to help you you're only chanche is to restore the boot loader but the way to do that i'm sorry i can't suggest... When it happened to me, recovery was gone and screen black with backlight, only fastboot worked and i sent every single piece of rom via usb. I wish you good luck.
No modes usually means 1 thing...
"Hard Bricked".
What i would try:
See what happens if you plug the device into charger or USB Cable.
Also "fastboot" would fix it... But you got no modes and as far as i know there is no way to use fastboot manually on this device.
At least i couldnt find a way.
Try:
Remove your battery and plug it again.
Remove any cables connected.
Try some button combos to see if it boots anywhere.
If not install android sdk.
In your computer (under dos prompt / shell / command line) manually run adb.exe
I.e:
Adb start-server
Adb devices
(see if your device number is shown).
If it is: System is on. Your device is detected. A solution may be possible.
If it is not (probably): Device is Hard Bricked.
Either ways. If screen is on then theres a tiny hope you can revive it.
I would see if Odin could detect it and repartition it. Or even try to get it connected to my PC and manage the partitions manually. But... We go back to fastboot.....
So i guess jtagging; replacing board so on... Would be the only option.
Or i would sell it for parts and get a new one since that one is probably dead. (Sad...)
Sent from my GT-I9003 using XDA Free mobile app
rgxHost said:
No modes usually means 1 thing...
"Hard Bricked".
What i would try:
See what happens if you plug the device into charger or USB Cable.
Also "fastboot" would fix it... But you got no modes and as far as i know there is no way to use fastboot manually on this device.
At least i couldnt find a way.
Try:
Remove your battery and plug it again.
Remove any cables connected.
Try some button combos to see if it boots anywhere.
If not install android sdk.
In your computer (under dos prompt / shell / command line) manually run adb.exe
I.e:
Adb start-server
Adb devices
(see if your device number is shown).
If it is: System is on. Your device is detected. A solution may be possible.
If it is not (probably): Device is Hard Bricked.
Either ways. If screen is on then theres a tiny hope you can revive it.
I would see if Odin could detect it and repartition it. Or even try to get it connected to my PC and manage the partitions manually. But... We go back to fastboot.....
So i guess jtagging; replacing board so on... Would be the only option.
Or i would sell it for parts and get a new one since that one is probably dead. (Sad...)
Sent from my GT-I9003 using XDA Free mobile app
Click to expand...
Click to collapse
Fastboot command are not possible with samsung devices they has Download mode which is barely the same of bootloader in other devices.
acuicultor said:
Fastboot command are not possible with samsung devices they has Download mode which is barely the same of bootloader in other devices.
Click to expand...
Click to collapse
So No Solution ? ! So Thank You So much Brothers for gave me You opinion and a ways So Thank
You can try jtag solution, look for it in xda.
acuicultor said:
You can try jtag solution, look for it in xda.
Click to expand...
Click to collapse
but i don't have a jtag tools ,
Also can try usb-jig to enter download mode
acuicultor said:
Also can try usb-jig to enter download mode
Click to expand...
Click to collapse
Brother i used it but no work
Hello again.
There's one last method you could try then...
- Required tools: 2 Persons (lol)
- A thin Clip
Remove the back cover from your device. Note that between the camera and speaker (literally in the middle), you'll see a tiny hole. That hole is another button.
1st remove your battery and place it again after 30 seconds. (Time for the device clears the components power).
Then Just press:
That tiny hole button + Volume Down + Home Button + Power Button
Try it a couple of times until your device boots into forced Download Mode.
Please press Thank button if it helped you.
Sent from my GT-I9003
i have some problems with my htc, i sent the device for hardware fix and the device was working. After the fix ive lost my software and i cant go to recovery or do anything, i can see the red led and i can launch the device but the screen is black and the device keeps reseting please help me and thanks
(sorry for bad english)
phantomcj223 said:
i have some problems with my htc, i sent the device for hardware fix and the device was working. After the fix ive lost my software and i cant go to recovery or do anything, i can see the red led and i can launch the device but the screen is black and the device keeps reseting please help me and thanks
(sorry for bad english)
Click to expand...
Click to collapse
try to boot to the bootloader
then select recovery
if that doesn't work then use a ruu.exe
rzr86 said:
try to boot to the bootloader
then select recovery
if that doesn't work then use a ruu.exe
Click to expand...
Click to collapse
my computer (win8.1) cant see my device and i have htc sync and the drivers and i cant boot to bootloader should i use BOX or what ?
phantomcj223 said:
my computer (win8.1) cant see my device and i have htc sync and the drivers and i cant boot to bootloader should i use BOX or what ?
Click to expand...
Click to collapse
search here on xda how setup adb/fastboot on win8
also try this
remove battery and put it back
press and hold together power button+volume until it gets you to the bootloader
if it gets you select recovery to see if you have access
rzr86 said:
search here on xda how setup adb/fastboot on win8
also try this
remove battery and put it back
press and hold together power button+volume until it gets you to the bootloader
if it gets you select recovery to see if you have access
Click to expand...
Click to collapse
well my phone is with a guy that uses riff box and this is the only way ive tried everything but there is some files are missing so he cant recover the bootloader and it is lost so my htc is empty phone there is no boot loader or software