i have done a lot of searching and cant fing the answer, i just got a replacement 1.3 rev focus from at&t. reflashed 7004, dev unlocked, updated to mango and interop unlocked, deployed a few apps, samsung tools, root tools, ect. plugged in my old phone to get navigon data off. worked fine using WP power tools. opened my new phone in wp power tools and deployed navigon 4.0 successfully. now every time i try to connect to the new phone i get error message: Connection Error! unlock your phone and make sure it is paired with zune. i also get the same error message with wp7 sdk app deployer.. tried multiple pc/phone restarts checked my hosts file.. blah blah blah. any help would be greatly apreciated i dont want to have to factory reset and then have to reflash to 7004 to re-devunlock. i already put all 8 gigs of official apps back on... ugh i want my side loaders back!
Related
I finally got connect between my HTC Touch Pro and OSX (parallels + Activesync)
I am trying to run RaphaelHardSPL-Unsigned_190_1_3 and everything goes well, but when it trys to connect to the device to start the mod, i get Error [202] Connection. I have tried enabling/disabling Advaned Network Funtionality in Connection settings, but that did not help. I have tried manually going into bootloader (when the transfer is about to start, I hold VolDown, and reset, and wait for Bootloader to go into USB mode). That didn't work for me.
My question(s) are, how can I get the HardSPL running, or how can I get my deviced flashed in general (SD method didn't work)
AND: My version in HARDSPL is stated to be 1.95.502.5. Is it OK if I downgrade to 1.90.1.3 in order to allow custom ROMs?
Thanks in advance.
Parallels doesn't play nice with the USB bridge.
Try boot-camp (works for me).
I crashed my first Kaiser, flashing with Parallels. Couldn't recover it after the usb connection cut out mid flash. I sent it in for warranty exchange, telling them it crashed while doing an " official " rom update. luckily no one looked too close and they sent me a replacement.
Now I only use Bootcamp and xp. And after more flashes than I can count, I have never had a problem.
Hello, mates!
Today I've made hard reset. After that my phone stopped recognizing any sim-cards. It writes that sim card isn't inserted. I've tried 3 sim cards without any success. All of this sim-cards work just fine in another phone.
I've already tried to do one more hard reset. And I've already tried to take sim card from the phone and boot it without card. It wasn't helpful.
Have you got any ideas?
Sim module is connected to the maniboard with the help of flex cable.It may be partiarlly dissconected.
I've already checked it twice... It's conected, I'm sure.
p.s.: flashlight is working great.
Have you tried to reflash rom?
No, I haven't. I tried to download 7.0.7389 ROM that you've uploaded, but I still can't download it.
Can you give me some advice where can I get 7008 or earlier build, or re-upload 7389 to another file srver?
I found many ROMs for other HTC devices, but not for "7 PRO".
http://rapidshare.com/files/4546556....64.09.20_22.42.50.15_Signed_GOLD_RELEASE.exe
Ok, downloading it. But do you have any links to 7008 or earlier builds? I don't want to lose jailbreak...
Unfortunately,for HTC 7 PRO there are no older build available.
oops... RUU updater says that it can't connect to device, code 260.
And I unable to unlock it through Chevron WP7. It says that my device probably PIN-locked or Zune is switched off. Both are turned on.
I tried to do soft & hard reset my phone. And I tried to reboot PC. Hopefully that problem due to using Windows 7 through Virtual machine. I use Mac OS...
Tomorrow I will be able to test it at work, on a real PC with Win 7. I hope it would be a solution.
You can switch HTC 7 PRO to bootloader manualy,connect to PC, then run the exe ROM
Ok, I'm in SPL now, but when I mount it to PC there is no driver and there is sign at the white strip "Serial". I suppose that it should be changed to "USB" when I connect device to PC. But it is doesn't occur.
Got it. Trying to update.
Strange behaviour. I updated the device to 7389. I unable to update it through Zune to 7390 - no update available.
Upd: connected device to Win 7 notebook, installed Zune, and here was an update to 7390.
But the most terrible thing that my sim-card still can't be recognized...
So i tried flashing 7720 from 7712 and it failed to flash in the middle of the process.
I wasnt freaking out until 'Windows Phone Support Tool' says this:
The phone is not in the 'Connect to PC' state. Please, make sure that you follow the instructions and your phone shows the 'Connect To PC' image
I have that "connect to pc" image but its still not working.
I uninstalled zune 4.8 and put 4.7 hoping it will make a difference. I even launched 4.7 and tried to restore but failed because theres no backup file, 4.8 deleted it. But i still have the backup that windows phone support tool created.
I also tried fully restoring my phone(i know..) using the up and down keys. Now when it turns on, instead of seeing the downloading screen, it has the same "connect to pc" image.
Any ideas?
I also have the same phone with NoDo, can i copy the backup from that and try that? or no because different serial numbers ect?
Zune detects the phone but damm no backup....
Ok i flashed DFT Freedom Rom! Im soo glad that worked. I wonder if i can revert back to stock NoDo?
I tried about 15 times last night to update to mango. I make it to step 6 where it restarts the phone. It will sit there for a few minutes with a connect to the computer icon on my phone screen. When it powers back up the update fails with the code 801812C1. I tried updating the driver for windows phone 7 and had the same result. also tried doing the update in airplane mode. Can anyone help? I don't know what else to try.
anyone? 38 views no replies
Any help would be appreciated!
Have you made sure you are running the latest version of the Zune software? I don't remember the error code off the top of my head, but that look similar to the code you get when you need to update to accomplish the update.
Yes I am currently running the latest Zune software
I have the latest software on my computer. Which is windows XP. Would I maybe need to update the Zune software on the phone?
Probably a totally newbie question but when I hit install I get
MAKE SURE YOUR PHONE IS UNLOCKED
PLEASE MAKE SURE YOU ARE CONNECTED TO PC ZUNE OPEN
Well I am connected to PC, Zune open and lock screen unlocked, phone is unlocked as I sideloaded Screncapture V3 Via Deploy.
What am I doing wrong? Phone is LG E900?
Same problem here...
Tom's XAP Installer, 1.2, isn't working for me either. I even went through the ChevronWP7Labls unlock again and still get the same error.
Has same issue before
I had the same issue.
After chevronlab unlock,
connect phone to zune,
once phone is detected in zune and synced
unlock the screen and install the xap file then you wont get error.
Phone is locked or phone is pin locked means phone screen is locked.. just need to unlock screen