After trying to install odin GB i went back to stock using Odin and now my GPS stop working is there a way to find out if ODIN did this or did i do something my self
Which odin package did you use? It's very unlikely 99.9% sure that odin did not do this.
Related
Was trying to flash back from epf1 leaked to CI510_VZW_ED2_ALL_ONE-LTE-CP_REV03_user_CL986330.tar.md5 but now no matter what i do i cant fix the baseband unknown error.
These are the files i've tried flashing with odin and havent had any luck.
CI510_VZW_ED2_ALL_ONE-LTE-CP_REV03_user_CL986330.tar.md5
CI510_VZW_EG2_ALL_ONE-LTE-CP_REV03_user_CL199635.tar.md5
CI510_VZW_EP1F_ALL_ONE-LTE-CP_REV3_user_CL300919_Rooted_Debloated.tar.md5
gb_ep1f_bloated.tar.md5
tried installing these with battery on while using odin and battery off.... no luck
Have you tried PST to flash it?
mbaran said:
Have you tried PST to flash it?
Click to expand...
Click to collapse
yes, didnt work
i followed the following post
http://rootzwiki.com/showthread.php?481-LEAK-STOCK-ED2-Droid-Charge-FULL-ODIN!
Same thing is happening to me. Happened after the OTA EE4 update. Had signal just fine on ED1 before the update. Phone is wiped and bone stock right now, baseband unknown after the update, so I'm taking it to the Verizon store.
Here's something to try. (I didn't use PST since I'm only really familar with ODIN and it seemed to work for me).
1) ensure you are using ODIN 1.82. I was using ODIN 1.3 earlier and it seemed to have some issues. :-/
2) using the original ED1 tar file from here: http://forum.xda-developers.com/showthread.php?t=1087342 download and extract the .md5 file
3) Connect your phone, place in download mode and run ODIN 1.82, under "PDA"
select the .md5 file you downloaded and extracted.
4) Remove SIM card as the directions in the above link state (I dunno if required)... but put your battery back in. I think this is REQUIRED when flashing lte_modem.bin part or the files.
5) flash with ODIN and restart once completed.
This reset my phone back to ED1 completely, including writing ED1 modems, which... prior, had been stuck on the EP1F leaked versions. :-(
I suspect it will do the same for your lack of baseband, too.
shrike1978 said:
Same thing is happening to me. Happened after the OTA EE4 update. Had signal just fine on ED1 before the update. Phone is wiped and bone stock right now, baseband unknown after the update, so I'm taking it to the Verizon store.
Click to expand...
Click to collapse
thats exactly what happened to me. after i ran the ee4 update.
Strange issue, phone I have has been rooted and different ROMS installed since Froyo to GB many times without issues. Weird thing, up to the day I switched to iphone it was working. Decided to sell this phone and a week later wanted to get in to do factory reset, phone won't boot - all it does is Samsung logo flashes on and off forever. I've tried two different batteries, tried to enter recovery mode, won't work. I tried ODIN on two different ROMS also, including PIT option with PIT file, etc. Still phone won't boot.
What else to try? I don't understand why it won't work. Each ROM I tried, passed in ODIN with no errors.
use Samsung PST and the EP4P stock VZW file with the pit. You can find instructions laying around, and the file you're looking for is something like VZW_EP4P_bloated.tar or something
Sent from my SCH-I510 using xda premium
You could also try and re download the files maybe they got corrupt somehow. If you cant find the EP4P file you could do a EE4 or even ED2 and it would update from there.
http://forum.xda-developers.com/showthread.php?t=1111486
http://www.mydroidworld.com/forums/...harge-full-factory-tar-flashing-software.html
Ive had my samsung infuse rooted and something happened? had to reboot back to stock... superoneclick seems to get stuck and not root my phone!! does it not work anymore? even when i download it from shortfuse... Ive dissabled usb debug....ive enabled usb debug....nothing works help
yeah I had the same issue with super one click on stock stock from GTG's unbrick
you may want to update to UCKE5/one or two builds above the stock build.
thanks how do i get this? from where? I cannot seem to get my cwm to open in the red!
you could probably just run this in odin to get back to UCKE3 which was stock in North America if you bought the phone a month after it came out. (Was stock for my phone when I bought it a month after it came out anyway).
http://forum.xda-developers.com/showthread.php?t=1112555
This has the bonus of already being rooted btw.
Anyway, UCKD5 is the rom that doesn't work with superoneclick properly from what I can tell which was stock when it came out and is GTG's ultimate unbricker's rom.
Don't use the pit because you most likely won't need it (your phone boots and all that stuff, right. If so, don't bother with repartitioning)
From here you're rooted and can setup modified 3E with root explorer and CWM with whatever you wanna use to set it up.
I used "[ODIN][UCKD5] Odin - Stock (100% or Root+3e)" (from Super Thread) to get to stock.
Then went to market and loaded SGS Kernel Flasher.
Then I downloaded Infused GB Core A2 kernel.
After I flashed the kernel, I had red CWM and went from there. Worked really well!
issues still
Download? How? Multiupload no good! mega no good either
They've been mirrored. I think. Not near pc.. No mirrors from me.
Sent from my SAMSUNG-SGH-I997 using Tapatalk
Hi all,
As the title says I am currently unable to boot past (red) CWM recovery on my Infuse. I figure it might be easier to get help if I explain everything I've done:
The other day I tried to flash Uniporn build 37 only to soft-brick my phone because I didn't have the GB bootloaders installed (I had previously been on CM7). I managed to nandroid back to CM7 and decided I'd give it another go today.
Since I was told that flashing bootloaders is very risky I decided to flash something easier first with Heimdall to make sure everything was working right. I ended up flashing the ICS kernel in qkster's thread (one-click)... mistake #1. That bricked my phone once again and gave me rainbows in recovery.
So then I decided to try a Heimdall flash to stock 2.3.6 UCLB3 (once again, the one-click Heimdall from qkster's thread), which did give me a bootable OS despite some rainbows while booting up. However, here I made mistake #2 and tried to recover from the CM7 backup I made earlier today with the Infuse Toolkit. This completely soft-bricked my phone; I couldn't even get into recovery at this point.
So, I tried to reflash the stock 2.3.6 with bootloaders this time, only (and this may be important, not sure) it tried and failed to flash a PIT. At this point I flipped because I thought I had hard-bricked the phone. After I calmed down and came back a while later, I discovered the phone wasn't hard-bricked at all and I was able to get it into download mode after all!
I then flashed stock Froyo (I'd had enough of that rainbow ****) and it seemed to go fine... only now it wouldn't boot past 3e recovery, despite me wiping data and cache multiple times. So I flashed the community kernel... same problem, only now with red CWM instead of 3e.
So... what can I do now? I'm relieved I don't have a hard-brick on my hands, but this isn't that much better... could that PIT be the problem? I hope the info I gave is enough to help (and isn't too much either!)
Screw ICS, now I just want my CM7 back
EDIT: I should also probably note that after I managed to get CWM back I tried to flash the UCLB3 ROM in the Infuse toolkit; it said it installed but when I rebooted the phone still went straight to CWM.
EDIT 2: Another weird thing I just noticed: the phone apparently refuses to stay turned off while it's plugged into the wall to charge. If I plug it in, it turns on and goes into recovery mode. This also can't be good, since IIRC the battery won't charge while in recovery.
Just heimdall or Odin again...I've had this happen soo many time when I had my infuse...I just simply run heimdall again and its good...if you ever get recovery after heimdal or Odin...do not hit reboot...wipe everything then hit reboot...
And gingerbread bootloaders are not required for ics...I keep hearing people say they brick there phones because they don't have gb bootloaders...that is not the reason...yes with out the bootloaders you get rainbow recovery and boot up but that is it!!!
Remember if you are going to ics from gingerbread...YOU HAVE TO double flash...the first flash will not work...just three finger back to recovery and flash again from.blue/rainbow recovery depending whether or not you have.bootloaders...
Look at my infinitum port thread...it has great instructions on how to flash ics roms...as well as how I flashed gingerbread bootloaders when I had my infuse
Sent from my HTC PH39100 using XDA
Nah, I've tried that, it's more broken than that. I think I need to reflash the PIT, which Heimdall doesn't like for some reason. I followed qkster's advice in another thread but still no dice. I might have to try using a different computer.
All fixed now, I used the Heimdall one-click on a Windows machine; the PIT and everything else flashed without a hitch and I'm up and running again.
just keep trying flash different stable stock roms thru odin until u can boot..i had it happen twice nd even couldn't get computer recognize my phone for a bit thru odin but it finaly workd now I'm back on cm9
Samsung Infuse ICS 4.0.1(cm9)
Hi there.
I´m on a 6210. Was on 4.0.4 rooted.
Still wanted to update to 4.1.2. using odin for flashing stock 4.1.2.
Got stock
I have download mode available and running windows 7 on the other side.
Have tryied to flash but it fails and now I´m between "firmware upgrade encountered an issue" screen or "odin download" screen.
The tablet seems to comunicate with pc but fails every time.
Even tryied to flash cwm to try to wipe but odin wont let me.
using odin 3 1.85 and also odin3 3.04 that worked for rooting and flashing my S4 a few weeks ago.
Any ideas? Currently I´m downloading a stock 4.0.4. to try to flash back to it.
Ah, I also looked up and downloaded a PIT table for the 6210 and tryied a few more times with it.
danielvelez said:
Hi there.
I´m on a 6210. Was on 4.0.4 rooted.
Still wanted to update to 4.1.2. using odin for flashing stock 4.1.2.
Got stock
I have download mode available and running windows 7 on the other side.
Have tryied to flash but it fails and now I´m between "firmware upgrade encountered an issue" screen or "odin download" screen.
The tablet seems to comunicate with pc but fails every time.
Even tryied to flash cwm to try to wipe but odin wont let me.
using odin 3 1.85 and also odin3 3.04 that worked for rooting and flashing my S4 a few weeks ago.
Any ideas? Currently I´m downloading a stock 4.0.4. to try to flash back to it.
Ah, I also looked up and downloaded a PIT table for the 6210 and tryied a few more times with it.
Click to expand...
Click to collapse
Update:
:fingers-crossed:
I changed the data cable (have one long and one short non stock cables) from the long one to the short one... Now it seems to be flashing with odin... so anybody with a similar issue, try for a better communication between pc and tablet..
I´ll update on a sec if I´m successfull.
danielvelez said:
Update:
:fingers-crossed:
I changed the data cable (have one long and one short non stock cables) from the long one to the short one... Now it seems to be flashing with odin... so anybody with a similar issue, try for a better communication between pc and tablet..
I´ll update on a sec if I´m successfull.
Click to expand...
Click to collapse
Fixed.
Now on Deodexed XXMF1... about to root. :cyclops:
great