Related
Hello,
I have an Evo Shift stuck in the boot loop. As soon as I put the battery in all it does is reset itself to the screen with the white background and green "HTC" logo, and will keep restarting until the battery dies.
If I hold volume down and turn it on, it does go into the bootloader, but picking ANYTHING, such as recovery or factory reset, does nothing but sending it back to the HTC screen.
I have tried flashing the RUU.exe (2.27.651.2) through Fastboot USB and it completed successfully, but it just restarts right back to the HTC screen. I have also put PG06img that I found on here on the root of my card, and it will never load it up.
Are there any other solutions anyone can think of? They would be much appreciated. I see a lot of these threads for regular Evos, but not for Shifts.
The only other thing I really know about the phone is that it is:
S-On
Hboot- 0.98.0001
Radio- 1.08.00.0506
Thank you so much for all of your help!
Seems to me you aren't rooted and that's more than likely your problem, boot into fastboot and use the ruu application for gingerbread.
Sent from my PG06100 using Tapatalk
Rooster85 said:
Seems to me you aren't rooted and that's more than likely your problem, boot into fastboot and use the ruu application for gingerbread.
Sent from my PG06100 using Tapatalk
Click to expand...
Click to collapse
While I am pretty sure I am not rooted, if you are talking about the early RUU release; 1.17.651.1, the application starts and then ends up failing in the beginning of the process. Is this what you are talking about? The drivers should be all good, the application starts to flash and then dies though. Thanks!
samcrac said:
While I am pretty sure I am not rooted, if you are talking about the early RUU release; 1.17.651.1, the application starts and then ends up failing in the beginning of the process. Is this what you are talking about? The drivers should be all good, the application starts to flash and then dies though. Thanks!
Click to expand...
Click to collapse
Use the new RUU. But make sure your SD card is formatted to a FAT32 partition. (Stock 2gig sd card and some other store boughts are not)
You can format on your computer and then place the RUU on the root of sd card again
(Bootloader won't recognize the ruu zip if not partitioned)
Sent from my Supreme Shift
notsointeresting said:
Use the new RUU. But make sure your SD card is formatted to a FAT32 partition. (Stock 2gig sd card and some other store boughts are not)
You can format on your computer and then place the RUU on the root of sd card again
(Bootloader won't recognize the ruu zip if not partitioned)
Click to expand...
Click to collapse
Ok, I just did this, everything updated fine and all completeted on the bootloader. It then said "press power to reboot." I did so, and went right back into the same boot loop. Any other ideas. I figured running this, and the RUU.exe on the computer were the sure fire ways to get this thing working again???
samcrac said:
Ok, I just did this, everything updated fine and all completeted on the bootloader. It then said "press power to reboot." I did so, and went right back into the same boot loop. Any other ideas. I figured running this, and the RUU.exe on the computer were the sure fire ways to get this thing working again???
Click to expand...
Click to collapse
So just a little information.
you said your not rooted?
So that means you have no ability to flash anything because you have no custom recovery and the bootloader isnt unlocked (S-on)
So what DID you do before it bootlooped? there had to have been something you were trying to do.
Not trying to blame anything on you at all just want to make sure we are helping the most accurate way possible
notsointeresting said:
So just a little information.
you said your not rooted?
So that means you have no ability to flash anything because you have no custom recovery and the bootloader isnt unlocked (S-on)
So what DID you do before it bootlooped? there had to have been something you were trying to do.
Not trying to blame anything on you at all just want to make sure we are helping the most accurate way possible
Click to expand...
Click to collapse
No I hear ya. I was sold the phone fairly cheap and was told "all you need to do is to reinstall the RUU, that is all that is wrong." Obviously I was skeptical, but when I checked everything out, everything looked good, and again, for the price, I knew it was a gamble. That being said, I'm sure something was tried in order to modify the phone and this is how it got like this.
I have soft bricked my old Evo 4g a handful of times and an RUU or Rom flash would always solve the problem.
Anyway, there is no custom recovery, and I'm pretty sure theres no root because it is still "S-ON," I am just trying to see if anyone here has any more info before it goes in for repair.
The only last thing I would guess you MIGHT be able to do is to install a custom recovery, but is there ANY way to do this by just being in the bootloader and using FASTBOOT USB? Any more help is greatly appreciated. Thanks!
samcrac said:
No I hear ya. I was sold the phone fairly cheap and was told "all you need to do is to reinstall the RUU, that is all that is wrong." Obviously I was skeptical, but when I checked everything out, everything looked good, and again, for the price, I knew it was a gamble. That being said, I'm sure something was tried in order to modify the phone and this is how it got like this.
I have soft bricked my old Evo 4g a handful of times and an RUU or Rom flash would always solve the problem.
Anyway, there is no custom recovery, and I'm pretty sure theres no root because it is still "S-ON," I am just trying to see if anyone here has any more info before it goes in for repair.
The only last thing I would guess you MIGHT be able to do is to install a custom recovery, but is there ANY way to do this by just being in the bootloader and using FASTBOOT USB? Any more help is greatly appreciated. Thanks!
Click to expand...
Click to collapse
It shouldn't have a custom recovery if it shows s-on.
I don't see why the RUU wouldn't work.
Honestly it doesn't sound like a softbrick- sounds like its just bricked (Which ive only heard of 1 Shift getting bricked completley)
notsointeresting said:
It shouldn't have a custom recovery if it shows s-on.
I don't see why the RUU wouldn't work.
Honestly it doesn't sound like a softbrick- sounds like its just bricked (Which ive only heard of 1 Shift getting bricked completley)
Click to expand...
Click to collapse
Make it 2! Thanks for your help though!!!
Also Stuck In A Bootloop
samcrac said:
Hello,
I have an Evo Shift stuck in the boot loop. As soon as I put the battery in all it does is reset itself to the screen with the white background and green "HTC" logo, and will keep restarting until the battery dies.
If I hold volume down and turn it on, it does go into the bootloader, but picking ANYTHING, such as recovery or factory reset, does nothing but sending it back to the HTC screen.
I have tried flashing the RUU.exe (2.27.651.2) through Fastboot USB and it completed successfully, but it just restarts right back to the HTC screen. I have also put PG06IMG that I found on here on the root of my card, and it will load it up (I'll see the blue loading bar and then the brown loading bar in the top right hand corner of the screen), but it then checks it again, and then goes back to the original screen for the bootloader.
Are there any other solutions anyone can think of? They would be much appreciated. I see a lot of these threads for regular Evos, but not for Shifts.
The only other thing I really know about the phone is that it is:
S-On
Hboot- 0.98.0001
Radio- 1.08.00.0506
Thank you so much for all of your help!
Click to expand...
Click to collapse
I'm trying to resolve a very similar problem as him, but I know of the history of my phone (since I'm the only owner), so hopefully an answer for me can assist him also.
The Story: One day, I'm playing Uno HD (downloaded from Android Market). I toss out a Draw 4, and then I see: "Google Infrastructure Failure" and a Triangle with an exclamation mark. I reset the phone, and it starts up fine. Then a few hours later, my phone randomly restarts itself into the bootloader screen after trying to reload the home screen (because the memory manager is overly aggressive).
I see no HTC Screen. It goes straight to the bootloader without any input. If I plug it to the charger from an off state, the amber light comes on, and 10 seconds later, bootloader screen. With a battery, it appears automatically after 45 seconds.
Fastboot can read my memory card just fine. It's already been re-formatted as FAT32 in my pitiful attempt to try to repair it. It's checked and read a PG06IMG file I placed on the SD Card's root, went through the entire process of reading it, but it doesn't ask me if I want to upgrade. It takes me back to the original screen. (Maybe I'm loading the wrong file).
Recovery and Factory Reset immediately restarts the bootloader after showing me the skateboarding android splash screen.
I've also tried to flash the newest stock RUU for it. (2.76.651.4), but after the RUU sends the command to start up in bootloader mode, the phone shuts off. Thus giving me the connection error.
(Maybe if someone could rewrite the .exe file to not send out the command to begin loading as if it was in the bootloader screen, it could work. I'd pay for that.)
Other Stuff:
ROM: Stock Sprint Gingerbread OTA ROM. I've been living the vanilla life. No root access. No funny stuff. Just a stock phone with apps (Third Blade, Uno HD, ASTRO File Manager, ect...)
Directly from bootloader screen:
SPEEDY XA SHIP S-ON
HBOOT-0.98.0001
RADIO-1.08.00.0506
eMMC-boot
April 11 2011, 22:32:34
Is there a way we can flash a file from the SD Card which will turn off the security and/or temp/perm root it? (forgive my noobness for such a question)
EDIT: I'm referring to a way that's outside of the adb push method. My device can't be found, and the device won't get past the bootloader screen, so that method doesn't help me too much. However, I do have the ADK Installed and the ADB Command Line works fine.
Ok .. HERE'S THE SOLUTION:
First off all if your S- ON it means you are NOT rooted
If you get stuck in a bootloop .. don't worry it can be fixed.
What you need to do is download PG06IMG.ZIP and place it on your sd card, you can access your sd card by going into recovery then mount section, then usb. This will allow you to move the file from your computer to the root of your sd card.
Once you do this be sure you back up any info you don't want to lose. Once you have the file in place, go back to fastboot ( hold vol down and power) it will read file and when it asks you to update press vol up. It will take a few minutes to update this will revert your phone back to stock but if you have an old recovery it will not do a full restore, it will only update the rom.
Once you get your phone back to working, I recommend updating your recovery by downloading Rom Manager and flashing the latest clockwork recovery. This problem happens usually due to an old recovery.
One other thing you can try if you do NOT want to reset your phone, you can try flashing a new kernal.
Sent from my PG06100 using Tapatalk
RUU won't work if your stuck in bootloop ..
Sent from my PG06100 using Tapatalk
If you want to root your phone use visionary to temp root then use shift rr .. you can then flash a custom recovery which is essential to avoid this from happening again
flylike2kites said:
I'm trying to resolve a very similar problem as him, but I know of the history of my phone (since I'm the only owner), so hopefully an answer for me can assist him also.
The Story: One day, I'm playing Uno HD (downloaded from Android Market). I toss out a Draw 4, and then I see: "Google Infrastructure Failure" and a Triangle with an exclamation mark. I reset the phone, and it starts up fine. Then a few hours later, my phone randomly restarts itself into the bootloader screen after trying to reload the home screen (because the memory manager is overly aggressive).
I see no HTC Screen. It goes straight to the bootloader without any input. If I plug it to the charger from an off state, the amber light comes on, and 10 seconds later, bootloader screen. With a battery, it appears automatically after 45 seconds.
Fastboot can read my memory card just fine. It's already been re-formatted as FAT32 in my pitiful attempt to try to repair it. It's checked and read a PG06IMG file I placed on the SD Card's root, went through the entire process of reading it, but it doesn't ask me if I want to upgrade. It takes me back to the original screen. (Maybe I'm loading the wrong file).
Recovery and Factory Reset immediately restarts the bootloader after showing me the skateboarding android splash screen.
I've also tried to flash the newest stock RUU for it. (2.76.651.4), but after the RUU sends the command to start up in bootloader mode, the phone shuts off. Thus giving me the connection error.
(Maybe if someone could rewrite the .exe file to not send out the command to begin loading as if it was in the bootloader screen, it could work. I'd pay for that.)
Other Stuff:
ROM: Stock Sprint Gingerbread OTA ROM. I've been living the vanilla life. No root access. No funny stuff. Just a stock phone with apps (Third Blade, Uno HD, ASTRO File Manager, ect...)
Directly from bootloader screen:
SPEEDY XA SHIP S-ON
HBOOT-0.98.0001
RADIO-1.08.00.0506
eMMC-boot
April 11 2011, 22:32:34
Is there a way we can flash a file from the SD Card which will turn off the security and/or temp/perm root it? (forgive my noobness for such a question)
EDIT: I'm referring to a way that's outside of the adb push method. My device can't be found, and the device won't get past the bootloader screen, so that method doesn't help me too much. However, I do have the ADK Installed and the ADB Command Line works fine.
Click to expand...
Click to collapse
Sent from my PG06100 using Tapatalk
Also if your phone can't be found its b/c you need to put it into diag mode .. ##DATA .. if you need more help google
tech-9 said:
If you want to root your phone use visionary to temp root then use shift rr .. you can then flash a custom recovery which is essential to avoid this from happening again
Sent from my PG06100 using Tapatalk
Click to expand...
Click to collapse
Sent from my PG06100 using Tapatalk
For the thread starter, the person that sold you the phone probably tried writing to the system partition with s-on. Since you can get to the bootloader, see if you can get into recovery. If you can, recovery can be seen in adb, even the stock recovery. From there, gingerbread root, plenty of guides out there, make sure you flash the misc.img, download the froyo downgrade zip (that pgimg09.zip or something like that, just search for it, but not with the numbers I just gave, those are made up.)
From there either flash the gingerbread zip or ruu, and goon with a unrooted life. Or follow one of the many guides to froyo root, and live the life of the rooted. Your choice.
For the second person with a similar issue, the same method will work for you (assuming you can get to recovery), gingerroot, froyo downgrade, and since you like being unrooted, just ruu or zip back to gingerbread.
Solution found enjoy, and just think, if root hadn't been discovered for gingerbread, you would be screwed right now, make sure to thank otaking.
I have the same boot loop problem. I tried using the PG06IMG.zip file and fastboot/bootloader screen says I have the wrong image. It's most likely because it's for 2.2 and I have 2.3. I also don't have any recovery. Is there a PG06IMG.zip for 2.3 or the like?
similar problem here
i'm fairly certain i tried recovery with the wrong or corrupt or incomplete PG06IMG.zip on my first attempt. i got the right one from here http://forum.xda-developers.com/showthread.php?t=1255474
i ran it, says update installed, but when i reboot i still get the loop
from bootloader
SPEEDY XE SHIP S-ON
HBOOT-0.93.0001
RADIO-1.07.00.1129
eMMC-boot
Nov 15 2010, 13:19:54
zdavidzz said:
i'm fairly certain i tried recovery with the wrong or corrupt or incomplete PG06IMG.zip on my first attempt. i got the right one from here http://forum.xda-developers.com/showthread.php?t=1255474
i ran it, says update installed, but when i reboot i still get the loop
from bootloader
SPEEDY XE SHIP S-ON
HBOOT-0.93.0001
RADIO-1.07.00.1129
eMMC-boot
Nov 15 2010, 13:19:54
Click to expand...
Click to collapse
Try downloading the zip again and re run it. Possibly a bad download?
Sent from my PG06100 using Tapatalk
also adb is telling me device not found. i think i might have to factory reset. is that crazy?
---------- Post added at 01:31 PM ---------- Previous post was at 01:27 PM ----------
and... that didn't help
i'm downloading the zip again right now.
since i have s-on, will i be able to install it though?
i can get the file on the root of the sdcard with an adapter since i can't push from adb. and i can't temp root the phone because if i try a normal reboot i get this stupid boot loop. is there a way to get s-off through hboot on the phone?
i don't know why i didn't notice that first file was messed up, it was only 6MB.
So I've tried to get S-On back for warranty purpose. I've used this tutorial:
S-ON
You may want to put your phone back to S-ON after following the rest of this guide, for example if you have reflashed your original rom and want to return it for warranty repair. Thanks to ikhzter thread, we have a way to do this!
1. Open Command Prompt, either Run "cmd" or go to Start, Accesories, Command Prompt
2. Enter the command: "cd C:\platform-tools" (Or whatever location you copied the folder to earlier)
3. Ensure your phone is switched on (regular home screen) and connect it by USB in charging mode (Ensure usb debugging is on settings > applications > development)
4. Enter the command "adb devices". It should come back with list of devices attached and then your serial number.
5. Enter the command "adb reboot bootloader". (You device will restart and boot into fastboot USB)
6. Enter the command "fastboot oem writesecureflag 3". (Thanks Dazweeja)
7. Reboot into bootloader using "fastboot reboot-bootloader" or remove & reinsert the battery and press power on while keeping hold of volume down.
8. Bootloader should now read Pyramid PVT Ship S-ON RL.
9. Remove and reinsert the battery. Press power on as normal
You should now have S-on back and you can return your device or do whatever it is covered again under warranty.
10. IF IT DOESN'T REBOOT and bootloader says ***Security Warning**
Remove and re-insert the battery and go back into bootloader and holding Volume Down +power button select fastboot
11. Run RUU_Pyramid_***.exe to reflash stock rom. (the one you downloaded earlier) and then reboot. It should work now
Now my phone is dead. When I connect it to my laptop I get a driver notification.
QHSUSB_DLOAD
Is there a way to fix this?
Thanks
Up HELP!? Someone??
I found the driver for QHSUSB_DLOAD. Now what?
Does it boot in bootloader ( Vol- + Power ) ?
No. It's dead. No led blinking.
Now it shows up in device manager unknown device when I connect it to my laptop.
Hi, stylus1828
I have similar prob.
My htc Sensation it's bricked. NO screen, NO lights, NO nothing
Qualcomm HS-USB QDLoader 9008
download mode waiting
how to start normal phone mode
please help me
I had the same problem once, I pulled the battery for a couple of hours.
After a few hours I placed it again and it just booted.
Don't know what to say but I think I'm screwed. I'm gonna send it to HTC, maybe they will not see what I've done and get a replacement. MAYBE!
A friend of mine had a full brick to because of bad rooting and got a new one without any probs. I hope you"ll be lucky aswell.
Let's hope so. Today I sent my phone back to warranty. Tomorrow I will get my answer.
stylus1828 said:
Let's hope so. Today I sent my phone back to warranty. Tomorrow I will get my answer.
Click to expand...
Click to collapse
Did you hear back from HTC? What did they say? I feel that unless you totally fried the phones internals they can probably tell that you rooted it when they try to diagnose the problem. What you are describing is the main reason I am so hesitant to root this phone. For your sake, I really hope they fix it for you! Let us know how this develops.
I sent my phone back to the online store from were I bought it. They seem to have an authorized gsm service and I'm waiting for a good answer from them.
I hope that I will get a new one without the dust issue. That was the reason I wanted to get S-ON back.
I just used those exact instructions to get back S-ON and my sensation appears to be bricked as well! someone should change those instructions! any way to fix this?
Instructions work fine if you actually follow them. I've done it. You skipped the most important part! You didn't flash stock ruu BEFORE doing anything else. Then you writesecure flag, then flash ruu again. It clearly states in the instructions to flash the ruu no matter what. Whether you're on stock already or not to make sure that nothing gets fouled up when s-on is set.
Behold_this said:
Instructions work fine if you actually follow them. I've done it. You skipped the most important part! You didn't flash stock ruu BEFORE doing anything else. Then you writesecure flag, then flash ruu again. It clearly states in the instructions to flash the ruu no matter what. Whether you're on stock already or not to make sure that nothing gets fouled up when s-on is set.
Click to expand...
Click to collapse
For what it is worth, I did flash back to stock rom before following these steps and I still got bricked.... has anyone actually followed these exact directions and not been bricked? I'm just thinking that for a stickied post with information in it that appears to have bricked several user's phones, it might need to be re-worded....
Even i used the exact same thing to get S-ON back and now my phone is bricked!!
Did htc replace or repair your handset?
I used the same instructions and it worked flawlessly, I also sent my phone because of the dust issue. I did follow it by the letter, maybe you forgot to boot the RUU when you installed it, or didn't have superCID?
Yes I have done the method without being bricked
I have a Htc Sensation running on the Tmobile network
i decided to go with a different rom and tried to install the rom from COREDROID SENSATION XE & 4G v5.1.
after installing it was stock on the boot screen.
I tried to SCID and install PG58DOAG.
at this point my phone will not boot.
I can get into the the recovery mode after i select "recovery" it goes to a screen with a red triangle and an exclamation mark.
I the volume up and power and the try to install a update...but non has worked
can get one help??
download this file http://www.filefactory.com/file/c19...00U_10.14.9035.01_M_release_223976_signed.exe
and run it with your phone plugged in your pc, it should do a stock recovery on your phone.
I faced the same issue with another ROM.
The only way I found to reboot was to reinstall the firmware while connected via USB with the PC.
And after that, I reinstalled the ROM.
I couldnt even boot.
primekrieger said:
I couldnt even boot.
Click to expand...
Click to collapse
Okay, first off stop digging up multiple 1 and 2 year old threads to post about your problem.
Second, be MUCH more specific about what the issue is. What happened before it stopped booting? Was it dropped or something or was it working fine?
Is it rooted?
Is it S-Off?
Skipjacks said:
Okay, first off stop digging up multiple 1 and 2 year old threads to post about your problem.
Second, be MUCH more specific about what the issue is. What happened before it stopped booting? Was it dropped or something or was it working fine?
Is it rooted?
Is it S-Off?
Click to expand...
Click to collapse
Sorry about that.
Here are the full details:
I have a Sensation XE, it was running ARHD 7.2, rooted, Bootloader Unlocked, S-OFF
I was playing subway surfers when all of a sudden the phone froze, no buttons nothing worked. After a while it itself restarted and got stuck on the white HTC boot screen. When it didnt progress for some minutes, I removed the battery, reinserted it and tried turning it on. But nothing, no signs of life were shown. Even on connecting the wall charger there was no charging LED.
Only thing is that windows can detect it as QHSUSB_DLOAD or something.
I checked out the Unbricking Sensation forum at: http://forum.xda-developers.com/show....php?t=1522351
but they say it works only for devices bricked while turning to S-ON, but as I mentioned mine is S-OFF. So, can I still use their method or is there some alternative?
Thanks
primekrieger said:
Sorry about that.
Here are the full details:
I have a Sensation XE, it was running ARHD 7.2, rooted, Bootloader Unlocked, S-OFF
I was playing subway surfers when all of a sudden the phone froze, no buttons nothing worked. After a while it itself restarted and got stuck on the white HTC boot screen. When it didnt progress for some minutes, I removed the battery, reinserted it and tried turning it on. But nothing, no signs of life were shown. Even on connecting the wall charger there was no charging LED.
Only thing is that windows can detect it as QHSUSB_DLOAD or something.
I checked out the Unbricking Sensation forum at: http://forum.xda-developers.com/show....php?t=1522351
but they say it works only for devices bricked while turning to S-ON, but as I mentioned mine is S-OFF. So, can I still use their method or is there some alternative?
Thanks
Click to expand...
Click to collapse
Can you get into recovery?
Sent from your phone. You should be careful where you leave that thing.
Skipjacks said:
Can you get into recovery?
Sent from your phone. You should be careful where you leave that thing.
Click to expand...
Click to collapse
No, I can't get to recovery. The phone doesn't start up at all. But windows detects something like QHSUSB_DLOAD when connecting through usb.
primekrieger said:
No, I can't get to recovery. The phone doesn't start up at all. But windows detects something like QHSUSB_DLOAD when connecting through usb.
Click to expand...
Click to collapse
Is the battery charging when you connect it to USB like that? If so I'd say to try an ruu to return it to completely stock. You will lose all user data on the internal memory when doing this. And it will return the phone to s-on and stock ROM. You will have to start over.
Do a search for ruu and you should find the thread that walks you through the process. Its really easy. You basically just run an .exe file from windows and it does everything else.
Sent from your phone. You should be careful where you leave that thing.
Skipjacks said:
Is the battery charging when you connect it to USB like that? If so I'd say to try an ruu to return it to completely stock. You will lose all user data on the internal memory when doing this. And it will return the phone to s-on and stock ROM. You will have to start over.
Do a search for ruu and you should find the thread that walks you through the process. Its really easy. You basically just run an .exe file from windows and it does everything else.
Sent from your phone. You should be careful where you leave that thing.
Click to expand...
Click to collapse
No, the charging LED doesnt glow.
Phone is detected on USB connection after i remove the battery. And moreover windows doesnt detect it as a phone i think.
PS: Losing data, S-OFF, ROM is not a concern. I just want it working, bought it just 6 months ago :crying:
primekrieger said:
No, the charging LED doesnt glow.
Phone is detected on USB connection after i remove the battery. And moreover windows doesnt detect it as a phone i think.
PS: Losing data, S-OFF, ROM is not a concern. I just want it working, bought it just 6 months ago :crying:
Click to expand...
Click to collapse
Do you have access to another battery just to make sure your battery isn't fried? If there is physical damage to the battery it will neither charge nor will it power on.
Also, try doing the ruu thing anyway. Worst its going to do is not work.
Sent from your phone. You should be careful where you leave that thing.
Skipjacks said:
Do you have access to another battery just to make sure your battery isn't fried? If there is physical damage to the battery it will neither charge nor will it power on.
Also, try doing the ruu thing anyway. Worst its going to do is not work.
Sent from your phone. You should be careful where you leave that thing.
Click to expand...
Click to collapse
As you said I searched for RUU for my phone, but now the problem is I can't decide what RUU to download since the phone wont start and therefore I can't see software number or CID.
primekrieger said:
As you said I searched for RUU for my phone, but now the problem is I can't decide what RUU to download since the phone wont start and therefore I can't see software number or CID.
Click to expand...
Click to collapse
from bootloader connect the device in the pc via usb(it should say fastboot usb)
open a cmd in the folder where you have adb and fastboot files and do these commands
fastboot getvar version-main
fastboot getvar cid
rzr86 said:
from bootloader connect the device in the pc via usb(it should say fastboot usb)
open a cmd in the folder where you have adb and fastboot files and do these commands
fastboot getvar version-main
fastboot getvar cid
Click to expand...
Click to collapse
Hi there!
Even my device is facing similar sort of problems. Although the situation is not as bad as the op,but still the phone is still just a paperweight.
Now what I did- unlocked bootloader via HTC dev site( HBOOT Ver 1.27)
Decided to S-off by J.Bear method.
Everyhting went fine untill the phone restarted. Controlbear no longer recognised the device. It said check your drivers.
That was the time when everything messed up.
Now the phone would no longer boot ahead of the white HTC bootscreen. And sometimes it even powers on directly to recovery(even when i'm not pressing volume down).
And one more strange thing happening.."adb devices" command doesn't show any devices listed although i can check the firmware and cid version(via fastboot command). And the device is showing up in device manager(my HTC). But adb commands are not working.
Am i missing something?
Any help would be much appreciated.
walkermoon said:
Hi there!
Even my device is facing similar sort of problems. Although the situation is not as bad as the op,but still the phone is still just a paperweight.
Now what I did- unlocked bootloader via HTC dev site( HBOOT Ver 1.27)
Decided to S-off by J.Bear method.
Everyhting went fine untill the phone restarted. Controlbear no longer recognised the device. It said check your drivers.
That was the time when everything messed up.
Now the phone would no longer boot ahead of the white HTC bootscreen. And sometimes it even powers on directly to recovery(even when i'm not pressing volume down).
And one more strange thing happening.."adb devices" command doesn't show any devices listed although i can check the firmware and cid version(via fastboot command). And the device is showing up in device manager(my HTC). But adb commands are not working.
Am i missing something?
Any help would be much appreciated.
Click to expand...
Click to collapse
probably your hboot get locked after S-OFF.that's why adb commands don't work(i think)
check your bootloader details
if now you have S-OFF and locked hboot flash 3.33 universal from here
http://forum.xda-developers.com/showthread.php?t=1459767
it will give you also patched hboot which is unlocked
follow the instructions to the letter(important)
and before flashing check md5 sums(important)
rzr86 said:
probably your hboot get locked after S-OFF.that's why adb commands don't work(i think)
check your bootloader details
if now you have S-OFF and locked hboot flash 3.33 universal from here
http://forum.xda-developers.com/showthread.php?t=1459767
it will give you also patched hboot which is unlocked
follow the instructions to the letter(important)
and before flashing check md5 sums(important)
Click to expand...
Click to collapse
Appreciate your concern.
But the thing is my device is still S On. The JBear method didn't finish. It messed up in between.
I'm attaching a pic. Give a look.
walkermoon said:
Appreciate your concern.
But the thing is my device is still S On. The JBear method didn't finish. It messed up in between.
I'm attaching a pic. Give a look.
Click to expand...
Click to collapse
hmm,
probably you need to use the temproot remove.bat file to remove temproot
check for troubleshooting in this thread
http://forum.xda-developers.com/showthread.php?t=1661631
also refer you issue there
ganeshp will help you further
or you can install 4ext recovery
enable smartflash from it and flash a custom rom
Novice here.
Ran the All-in-One utility today and after the CWM installed I hit "Perm root" without reading the thing below telling me to boot to recovery first. It's now stuck in boot loop. Everything went off fine up until the Perm root. Even that said successful and then restarted. Only after the process was completed did the recovery loop begin. No HTC logo loop. Just reboots into CWM over and over no matter what technique I use (except for opening the case).
I've read this: http://forum.xda-developers.com/showthread.php?t=1599363
And am trying to install ADB to push ANY possible ROM over to the SD card. My recovery allows the toggle of /mount sdcard and /mount system, however adb fastboot push doesn't work. "error: device not found"
And I can't do this: http://forum.xda-developers.com/showthread.php?t=1644730 because my phone is stuck in the recovery loop. If I try volume down + power, it just comes back to recovery screen. I've tried factory reset, I've tried wiping cache, I've tried wiping Dalvik, and still nothing. I did flash the SuperSu.zip after I had used the Perm Root button on Haroon2000's app.
I'm incredibly flustered as I've rooted devices for years and this is my first problem. I've seen similar complaints all with ideas of breaking into the phone and unplugging it's battery so I can get to the bootloader etc, but I'm so very confused. So many posts telling me to do so many things.
Can someone please help break down a tangible solution here? I'm freaking out.
Cheers
EDIT: If someone can get my phone fixed, I'll Paypal them $50 USD. I really need my phone back ASAP :\
I don't know if this is your solution, but you did not mention it as one of your attempts.
Have you looked into running an RUU?
Sent from my HTC One S using xda premium
beats4x said:
I don't know if this is your solution, but you did not mention it as one of your attempts.
Have you looked into running an RUU?
Sent from my HTC One S using xda premium
Click to expand...
Click to collapse
I'll update this again once I try breaking the phone down and yanking the battery. But I have tried running the RUU. I can't get to the bootloader right now and it's not listing the device when I adb devices.
I'm going to go home from work since I've spent 7 hours on two machines (XP/7) trying to fix this PoS and redo everything from the ground up. Hopefully my anger will have overcome it.
Something I've noticed however, is that within the CWM recovery, I can use the All-in-one tool to reboot the phone. So it is reacting to ADB commands. Perhaps trying to use ADB fastboot (Right-click method) instead of full ADB installation could be a problem with trying to push a ROM zip. Also, as far as the RUU goes. I don't remember what happened there. I'll edit this when I get home.
nik.the said:
I'll update this again once I try breaking the phone down and yanking the battery. But I have tried running the RUU. I can't get to the bootloader right now and it's not listing the device when I adb devices.
I'm going to go home from work since I've spent 7 hours on two machines (XP/7) trying to fix this PoS and redo everything from the ground up. Hopefully my anger will have overcome it.
Something I've noticed however, is that within the CWM recovery, I can use the All-in-one tool to reboot the phone. So it is reacting to ADB commands. Perhaps trying to use ADB fastboot (Right-click method) instead of full ADB installation could be a problem with trying to push a ROM zip. Also, as far as the RUU goes. I don't remember what happened there. I'll edit this when I get home.
Click to expand...
Click to collapse
Okay, update.
I was able to get ADB working and detect my phone.
Next, I was able to push Venom Rom to phone. I factory reset, wiped cache, wiped Dalvik, and was able to install Venom.zip. It then asked to reboot (per Venom screen) and I said okay. It then returned to CWM Recovery. I was confused but left everything as is. I have now reset the phone by holding the power button for around 10 seconds. It then restarted to the HTC Quietly Brilliant screen. I have been looking at that screen for about 5 minutes.
Also pertinent: I did try to run the RUU, but it didn't connect through USB. (I forget what it said verbatim). So that didn't work. I also was able prior to this entire process get into the bootloader via dumb luck.
Any suggestions? I am staring at the HTC boot screen still. Do I try to restart and enter bootloader? If so, then what? It seems there is something wrong with CWM. Can I switch recoveries? Can I uninstall it?
Calm down we have all been there,
When you flashed venom did you flash the boot image? Also i use twrp instead of cwm i find twrp better .
To enter bootloader hold power button and down vol together .
As gazknight said, this seems like proper kernel not being flashed or having an issue. If you flashed the boot.img with fastboot, try again erasing cache from fastboot first. The commands are as follow:
fastboot erase cache
fastboot flash boot boot.img (where this boot.img is the one inside the zip from the rom you choose and must be left in the same folder than fastboot)
It happened to me a couple times when i was on hboot 1.14 that I had to flash the boot.img a second time sometimes, somehow it was not working the first time, randomly, even though the flash had completed ok on fastboot.
If still doesn't work try doing a factory reset from TWRP and flashing ViperOneS again.
If that still doesn't work, you might want to try another rom, like TrickDroid, you would then have to flash the boot.img from this other room with fastboot, remember that.
Try and let us know
Hold down volume down while you're trying to boot, that will get you in boot loader, go to fast boot by pressing the power key, connect your phone to your computer, run the flash viper boot img thingy and you're set!
Envoyé depuis mon HTC One S avec Tapatalk
Same issue with HTC One S bricked but in European version, Stock ROM
hello,
I did't want to start a new topic, as I'm experiencing a similar issue with my HOS. Briefly, yesterday morning I plug the phone from charger at 06.00 am. Play with it for a while and then go to work. Used it at work for a few phone calls until 10.00 am (so 4 hours on fully charge battery). Then at 10.00 am I went into a meeting and left the phone out of my sight for 20-30 minutes. When I came back from the meeting I realize that the phone was closed. I try to open it (power button) but nothing. Press power for 10-30 seconds with volume down - still no effect.
Then I took the charger (the original one that I always use to cherge it) and plug it, left it for 2-3 minutes and press power. The phone starts but all I have is the white screen with HTC logo and if I press the power button + volume down the phone goes into bootloader. That's all I can do with it for now.
I have stock rom, bootloader is locked and I never try to root the phone. Is it any chance to repair it by myself or I have to sent it to the repair shop.
many thanks in advance.
Alright so I feel like I'm getting closer.
Here's whats happening now. It's in the HTC boot screen loop. I can get it into bootloader whenever I want, but now it's not detecting /sdcard in recovery. Within the bootloader, fastboot won't detect my device and my computer (Windows 8) claims the device is malfunctioning. I can still use fastboot adb commands from my computer when it is in recovery. I have gone into bootloader and cleared storage, as well as factory reset after. Also, it used to reboot into recovery endlessly. Now it appears that isn't hte case and reboots from recovery into the OS, but will not work.
I'm going to try and flash using adb w/o sdcard the boot.img as suggested above. I'll keep updating so others can know the process if they soft-brick their phone (I'm assuming this is a soft brick because I can still run things etc).
Update: trying to do fastboot erase cache from within recovery gives me "Waiting for device". As I've said, for some reason, it says the device is malfunctioning/not detected when I'm in the 1.14 Hboot Bootloader. But again, I can issue adb devices from within recovery. Sdcard still not mounting.
Edit: I'm issuing adb commands through adbfastboot files. Do I need to have the Android SDK fully installed with the Manager thing, or does the basic adbfastboot work (From here: http://www.htconeforum.com/forum/ht...e-your-htc-one-s-back-100-stock-relocked.html). That adb fastboot has the following files: adb, fastboot, adbwinapi.dll, adbwinusbapi.dll.
I think the source of the current problem is that I can no longer access my /sdcard or mount it. One step forward, then two steps back -_-.
nik.the said:
Alright so I feel like I'm getting closer.
Here's whats happening now. It's in the HTC boot screen loop. I can get it into bootloader whenever I want, but now it's not detecting /sdcard in recovery. Within the bootloader, fastboot won't detect my device and my computer (Windows 8) claims the device is malfunctioning. I can still use fastboot adb commands from my computer when it is in recovery. I have gone into bootloader and cleared storage, as well as factory reset after. Also, it used to reboot into recovery endlessly. Now it appears that isn't hte case and reboots from recovery into the OS, but will not work.
I'm going to try and flash using adb w/o sdcard the boot.img as suggested above. I'll keep updating so others can know the process if they soft-brick their phone (I'm assuming this is a soft brick because I can still run things etc).
Update: trying to do fastboot erase cache from within recovery gives me "Waiting for device". As I've said, for some reason, it says the device is malfunctioning/not detected when I'm in the 1.14 Hboot Bootloader. But again, I can issue adb devices from within recovery. Sdcard still not mounting.
Edit: I'm issuing adb commands through adbfastboot files. Do I need to have the Android SDK fully installed with the Manager thing, or does the basic adbfastboot work (From here: http://www.htconeforum.com/forum/ht...e-your-htc-one-s-back-100-stock-relocked.html). That adb fastboot has the following files: adb, fastboot, adbwinapi.dll, adbwinusbapi.dll.
I think the source of the current problem is that I can no longer access my /sdcard or mount it. One step forward, then two steps back -_-.
Click to expand...
Click to collapse
You might need to do it as administrator.
I think I've got it. One last tip. All of the above has been helpful, but I think the problem was trying to use my Windows 8 laptop. The second I got to work, I plugged it in on the bootloader to my XP machine and voila! it recognized fastboot and listed devices.
I have tried to run the RUU 2.35.531.7 but just like unrooting my old phone, I had issues because that update was already on this phone, so it goes through the entire process only to tell me on the windows XP utility that it had failed because it was the wrong update. When I did this to my old One S right before I sent it into Tmobile for warranty, it did the same thing with the 1.53 RUU, then when I found the 2.35, it worked like a charm.
So my last question (hopefully) then is, am I missing something as for installing an OLD or exact same RUU? Or is there a newer one than the 2.35.531.7?
I haven't tried on a Windows 7 machine, but I have one available here at work. I'm wondering if I should try to fastboot a ROM. Any suggestions what I can do to get it back to stock, or an old old stock version? I'd like to root it so I can use my Titanium Backup.
Update: Before ending this reply, I read that the RUU may be failing because the bootloader is unlocked/tampered still. I'm going to run it again to grab the error code to make sure of the issue, because it seems you should be able to revert or use any RUU (correct?).
nik.the said:
I think I've got it. One last tip. All of the above has been helpful, but I think the problem was trying to use my Windows 8 laptop. The second I got to work, I plugged it in on the bootloader to my XP machine and voila! it recognized fastboot and listed devices.
I have tried to run the RUU 2.35.531.7 but just like unrooting my old phone, I had issues because that update was already on this phone, so it goes through the entire process only to tell me on the windows XP utility that it had failed because it was the wrong update. When I did this to my old One S right before I sent it into Tmobile for warranty, it did the same thing with the 1.53 RUU, then when I found the 2.35, it worked like a charm.
So my last question (hopefully) then is, am I missing something as for installing an OLD or exact same RUU? Or is there a newer one than the 2.35.531.7?
I haven't tried on a Windows 7 machine, but I have one available here at work. I'm wondering if I should try to fastboot a ROM. Any suggestions what I can do to get it back to stock, or an old old stock version? I'd like to root it so I can use my Titanium Backup.
Update: Before ending this reply, I read that the RUU may be failing because the bootloader is unlocked/tampered still. I'm going to run it again to grab the error code to make sure of the issue, because it seems you should be able to revert or use any RUU (correct?).
Click to expand...
Click to collapse
The bootloader does need to be relocked for the RUU too work and the RUU you used before should work because I have used the same RUU a few times and it worked fine.
Darknites said:
The bootloader does need to be relocked for the RUU too work and the RUU you used before should work because I have used the same RUU a few times and it worked fine.
Click to expand...
Click to collapse
I'll try that. thanks.
Now on the same XP computer, it's not showing when I adb devices, however it does show in device manager. This changed after trying to do the RUU without relocking.
Yeah! Fixed!
After enough toggling, I changed the recovery to the T one and relocked my bootloader. It turns out detecting the device wasn't necessary somehow. Then I ran the RUU and voila!
nik.the said:
I'll try that. thanks.
Now on the same XP computer, it's not showing when I adb devices, however it does show in device manager. This changed after trying to do the RUU without relocking.
Click to expand...
Click to collapse
Not sure whats up with that, never had any issue on win7.
Windows 8 fastboot works on my laptop for some reason. I installed the drivers from the HTC Sync folder.
Sent from my HTC One S using Tapatalk 2
As the title says, RUU attempts booting my phone but it never comes back on. Even selecting restart boot loader in fastboot or a command it doesn't power itself back on. I have read through other forums and nothing has worked for me yet.
EDIT: I should probably clarify fastboot usb WORKS. Ruu must see my phone considering it detects the ROM version and turns the phone off in attempt to reboot. Anything that I do that requires a reboot doesn't work. I have tried unlocking the bootloader again, everything is fine until it comes to rebooting then I must turn the phone on myself and nothing changes...... IT DOESN'T REBOOT ITSELF therefore seemingly nothing wants to work. And the HTC boot screen is gone??
More background information: http://forum.xda-developers.com/showthread.php?p=39046436#post39046436
What we're your steps exactly? Did you relock your bootloader
a box of kittens said:
What we're your steps exactly? Did you relock your bootloader
Click to expand...
Click to collapse
Yes I did through fast boot with the oem lock command. I've tried installing RUU with a Windows 7 laptop (has HTC sync software) and Windows 8 desktop (basic drivers). Both failed, tried using Windows XP/Vista in compatibility modes and running as an admin with the same results.
Error 171 is a connection error, meaning the RUU can't connect to/find your phone.
Try uninstalling HTC Sync, rebooting your pc, and installing it again. If you've got the Android SDK installed, be sure it's also fully updated.
iElvis said:
Error 171 is a connection error, meaning the RUU can't connect to/find your phone.
Try uninstalling HTC Sync, rebooting your pc, and installing it again. If you've got the Android SDK installed, be sure it's also fully updated.
Click to expand...
Click to collapse
No luck. And I believe it does see the phone in the beginning of the installation. It makes it reboot to the boot loader and that's where it loses the connection. The phone just isn't booting itself back up. I appreciate the reply, if you have anymore ideas please let me know.
Could be something got corrupted. Try redownloading the ruu. Does adb see the phone?
iElvis said:
Could be something got corrupted. Try redownloading the ruu. Does adb see the phone?
Click to expand...
Click to collapse
Re-downloaded RUU and still no go. And adb doesn't see my phone, will it on the fastboot menu? I'm not to familiar with it.
Does anybody else have some more ideas?
Okkoto said:
And adb doesn't see my phone, will it on the fastboot menu? I'm not to familiar with it.
Click to expand...
Click to collapse
No. If adb doesn't see it, fastboot won't either. Does the command "adb devices" (no quotes) show the device as connected?
It sounds like the connection might be working for a few things (like rebooting the phone, as you mentioned). But I still think a connection issue is the main problem.
redpoint73 said:
No. If adb doesn't see it, fastboot won't either. Does the command "adb devices" (no quotes) show the device as connected?
It sounds like the connection might be working for a few things (like rebooting the phone, as you mentioned). But I still think a connection issue is the main problem.
Click to expand...
Click to collapse
Fastboot does see it but adb does not. And what I mean by rebooting the phone in my last post is RUU attempts rebooting it from the boot loader which does turn the phone off but it stays turned off. I've used other commands to reboot the phone from the fastboot screen and those too turn off the phone then again it doesn't come back on like a reboot should do.
I have about completely gave up and going back to using a regular feature phone. I have watched a video about a jtag repair service and was wondering about that or just selling the phone as bricked on ebay.
Okkoto said:
I have about completely gave up and going back to using a regular feature phone. I have watched a video about a jtag repair service and was wondering about that or just selling the phone as bricked on ebay.
Click to expand...
Click to collapse
don't sell it as bricked since it is obviously not bricked. you could get more money just saying you dont wtf your doing and gave up on it. but ill buy it as a bricked phone =) ill give you 50 bucks.
DvineLord said:
don't sell it as bricked since it is obviously not bricked. you could get more money just saying you dont wtf your doing and gave up on it. but ill buy it as a bricked phone =) ill give you 50 bucks.
Click to expand...
Click to collapse
Well if it's not bricked then I sure wish somebody would lead me to the right direction. I have tried 5 different PCs (which all show as connected through fastboot) and they all came with the same error. I've tried everything I could possibly think of and I haven't seen anyone else with quite the same problem I'm having.
I still have not completely gave up and have already decided against selling it as "bricked". The bootloader still comes up so there is at least some hope.
i just had the same problem. the solution was simple - i switch usb-port from front one to the backside one which is directly on motherboard.
Okkoto said:
Well if it's not bricked then I sure wish somebody would lead me to the right direction. I have tried 5 different PCs (which all show as connected through fastboot) and they all came with the same error. I've tried everything I could possibly think of and I haven't seen anyone else with quite the same problem I'm having.
I still have not completely gave up and have already decided against selling it as "bricked". The bootloader still comes up so there is at least some hope.
Click to expand...
Click to collapse
when you say it shows connected through fastboot what do you mean?
how are you getting the device into fastboot - through recovery??
oh, and what was on your device before you tried loading the RUU?
kkm68 said:
i just had the same problem. the solution was simple - i switch usb-port from front one to the backside one which is directly on motherboard.
Click to expand...
Click to collapse
Yes this + if you're on a usb3 port try usb2. Also make sure you're using the cable that came with the phone as I understand other cables may cause issues like this. Also, avoid using a hub or usb extension.
Solution to error 171
I had the same problem and after many attempts I finally got it to work!
-Uninstall anything HTC related from your computer such as HTC Sync Manager and Drivers. Also delete any HTC folders from your program files.
-Make sure you leave the sdk and adb stuff that you downloaded.
-Connect your device via USB to your computer and let it recognize it. It will automatically install default drivers.
-A pop-up asking to install HTC Sync will appear, just ignore it.
-Make sure you set Fast Boot OFF on your phone, and Debugging ON.
-Leave your phone ON and run the RUU set up.
-Then follow the steps on the wizard and everything should work just fine!
diegoyabishh said:
I had the same problem and after many attempts I finally got it to work!
-Uninstall anything HTC related from your computer such as HTC Sync Manager and Drivers. Also delete any HTC folders from your program files.
-Make sure you leave the sdk and adb stuff that you downloaded.
-Connect your device via USB to your computer and let it recognize it. It will automatically install default drivers.
-A pop-up asking to install HTC Sync will appear, just ignore it.
-Make sure you set Fast Boot OFF on your phone, and Debugging ON.
-Leave your phone ON and run the RUU set up.
-Then follow the steps on the wizard and everything should work just fine!
Click to expand...
Click to collapse
I have a similar problem with my HTC One. I am stuck in the bootloader and any action I take leads straight into a boot loop. If I try to reboot, reboot-bootloader, go into recovery (twrp), or factory reset it goes into a boot loop. Also I can't lock the bootloader and flashing my recovery doesn't help, even though it says its a success. I've tried three computers and deleted and reinstalled drivers but still the computers only find my phone in fastboot usb and can't find it using adb.
This solution above won't help me since I can't get my phone on for the life of me. I tried running RUU and All-in-One Toolkit but no luck. RUU fails finding the bootloader since my phone gets stuck in its boot loop. I am fresh out of ideas so any other ways to fix this issue would be greatly appreciated.
BTW I found my phone is this condition when I pulled it out of my pocket. I never installed custom ROMs on it. It is unlocked and rooted though running 4.2.2 (3.05.651.6) hoot 1.55. The only thing I can think of is that an OTA update got pushed to my phone and bricked it. That or for some strange reason something went wrong with phone from the rooting process after two weeks of it working perfectly.
jondon156 said:
I have a similar problem with my HTC One. I am stuck in the bootloader and any action I take leads straight into a boot loop. If I try to reboot, reboot-bootloader, go into recovery (twrp), or factory reset it goes into a boot loop. Also I can't lock the bootloader and flashing my recovery doesn't help, even though it says its a success. I've tried three computers and deleted and reinstalled drivers but still the computers only find my phone in fastboot usb and can't find it using adb.
This solution above won't help me since I can't get my phone on for the life of me. I tried running RUU and All-in-One Toolkit but no luck. RUU fails finding the bootloader since my phone gets stuck in its boot loop. I am fresh out of ideas so any other ways to fix this issue would be greatly appreciated.
BTW I found my phone is this condition when I pulled it out of my pocket. I never installed custom ROMs on it. It is unlocked and rooted though running 4.2.2 (3.05.651.6) hoot 1.55. The only thing I can think of is that an OTA update got pushed to my phone and bricked it. That or for some strange reason something went wrong with phone from the rooting process after two weeks of it working perfectly.
Click to expand...
Click to collapse
Nobody here can help you as we don't have any experience with your device. You'd be much better off asking in the HTC One forum which you'll find here:
http://forum.xda-developers.com/htc-one
Sent from my Evita
Heisenberg said:
Nobody here can help you as we don't have any experience with your device. You'd be much better off asking in the HTC One forum which you'll find here:
http://forum.xda-developers.com/htc-one
Sent from my Evita
Click to expand...
Click to collapse
hi all..
facing same problem with HTC Desire 816 n 4g... have anyone got any solution??
plz pass it..
thank you