Related
so I'm beginning to accept the fact that there's not much I can really do about my loose hinge. the truth is, it doesn't really hinder me in during regular use at all. however, its frustrating that I know it could have been better.
I might be satisfied if there was some case or something that secured the screen when open a bit more. maybe something involving magnets. anybody heard of anything like this? anybody wanna brainstorm on how to improvise it?
j.books said:
so I'm beginning to accept the fact that there's not much I can really do about my loose hinge. the truth is, it doesn't really hinder me in during regular use at all. however, its frustrating that I know it could have been better.
I might be satisfied if there was some case or something that secured the screen when open a bit more. maybe something involving magnets. anybody heard of anything like this? anybody wanna brainstorm on how to improvise it?
Click to expand...
Click to collapse
Dude... forget about it. If its really that bad... return it. Magnets will ruin the built in compass and god knows what other parts. Bad idea. Its supposed to be floatly. Trust me... its a welcom addition compared to the mytouch slide keyboard. The g2 is pretty smooth and as long as it doesn't fall when you hold it in a normal position, who cares...
This is my first post, hehe
bought my G2 on the 6th from Tmo store, mine is pretty solid, not loose at all, upside down, 45 degree angle, the screen doesnt go nowhere, closed or open, if i dont push it, it doesnt move, not even if i forcefully flick it!
im sure you could get a new one from tmobile/htc if it really bothers u, but looking at videos on youtube of the faulty screen, it would sure as hell bother me! good luck!
I'm in the same boat as j.books here. I'm LOVING the phone and while the wiggly hinge isn't an issue in how I use my phone it is just annoying knowing that it could/should have been better. I don't think I'm going to go through the hassle of returning the phone; it runs so well, I'm really afraid to spit in it's eye. :S
I'd contact whoever you got the phone from. If it is terribly loose and wiggly it's either a factory defect, packing fault. Possibly also fault of carrier. Either way if it's that much of an issue you may as well take the time to get to the bottom of it and figure out who to contact for a replacement or where to send your back to get it fixed. It's inconvenient for the user so make that clear when you contact them and demand some compensation.
I called t-mo last week and went to a t-mo store. it wasn't a 'known issue' at that point, and the t-mo store was absolutely worthless in terms of advice. one person was rude, one was nice, but both told me to call customer support, even though I already had.
the more I use the phone, the less of an issue it is. but it still bothers me. esp now that I know some people don't have the loose hinge. my 2 weeks is up on monday so I'm gonna call today and see if I am able to exchange it. problem is, I really don't want to go the whole weekend without it :\
j.books said:
.....maybe something involving magnets. anybody heard of anything like this?
Click to expand...
Click to collapse
I heard of magnets but I have no idea how they work....
....trollface.jpg
Take it apart, find the springs, and replace them with stronger ones. Other than that, your choices are replace it or live with it. Personally I'd replace the springs since I like to take things apart
Tell me how it goes don't see a G2 dis-assembly vid anywhere around
linkmaster_6 said:
I heard of magnets but I have no idea how they work....
....trollface.jpg
Click to expand...
Click to collapse
effin magnets, how do they work?
SuperDave81 said:
effin magnets, how do they work?
Click to expand...
Click to collapse
effing miracles
j.books said:
so I'm beginning to accept the fact that there's not much I can really do about my loose hinge. the truth is, it doesn't really hinder me in during regular use at all. however, its frustrating that I know it could have been better.
I might be satisfied if there was some case or something that secured the screen when open a bit more. maybe something involving magnets. anybody heard of anything like this? anybody wanna brainstorm on how to improvise it?
Click to expand...
Click to collapse
If you wanted to do this you need self adhesive magnet tape, thinest available less than 1mm or I don't think this mod will help.
Disclaimer. I haven't tried this but am sure it will work.
Cut tape to 2 1/4" x 1/2"
Cut 1/8" wide notch @ 1" to the right of left/rear edge.
Depth of notch [email protected] 1/4" ( the notch is for the small microswitch that senses the phone is closed, this switch also creates the limiting factor of magnet thickness. Bend the hoop upward you say? )
Test fit before you remove the backing ( magnet tape is placed between ribbon cable on left and 3rd hinge on right with notch around the microswitch. )
Good Luck!
PS this mod will hold the screen open and closed with no effect in between. I don't think it'll effect the compass because there is already tons of EMI in these devices, also you can recalibrate the compass and since the magnet is static it should compensate. Again good luck! And post pics if anyone is brave enough to attempt.
.
SuperDave81 said:
effin magnets, how do they work?
Click to expand...
Click to collapse
This thread is going places
kgold708 said:
If you wanted to do this you need self adhesive magnet tape, thinest available less than 1mm or I don't think this mod will help.
Disclaimer. I haven't tried this but am sure it will work.
Cut tape to 2 1/4" x 1/2"
Cut 1/8" wide notch @ 1" to the right of left/rear edge.
Depth of notch [email protected] 1/4" ( the notch is for the small microswitch that senses the phone is closed, this switch also creates the limiting factor of magnet thickness. Bend the hoop upward you say? )
Test fit before you remove the backing ( magnet tape is placed between ribbon cable on left and 3rd hinge on right with notch around the microswitch. )
Good Luck!
Click to expand...
Click to collapse
thanks dude. I was thinking of something like that, but I wasn't sure any magnetic tape would be thin enough. I looked it up and they never seem to specify the thickness, but there are products described as 'extra thin,' such as this: http://www.amazon.com/Extra-Flexible-Adhesive-Magnetic-Dispenser/dp/B000NNQ1CK ...think it would work?
SuperDave81 said:
effin magnets, how do they work?
Click to expand...
Click to collapse
hahaha. you just blew my f***ing mind
j.books said:
thanks dude. I was thinking of something like that, but I wasn't sure any magnetic tape would be thin enough. I looked it up and they never seem to specify the thickness, but there are products described as 'extra thin,' such as this: http://www.amazon.com/Extra-Flexible-Adhesive-Magnetic-Dispenser/dp/B000NNQ1CK ...think it would work?
Click to expand...
Click to collapse
Umm.... yep that looks like it'll do. When you get it stick some on wax paper, flip upside down,get one of those 6" metal "machinist rulers" , do your layout with a sharp pencil,and cut with exacto knife or new utility blade, test fit before removing wax paper(also compass,gps,etc function). Maybe use some cardboard pieces to hold the hinge open, getting the magnet into position will be the hardest part. Good luck and post pics/review.
This idea really appeals to my inner hacker.
keenerb said:
This idea really appeals to my inner hacker.
Click to expand...
Click to collapse
Do It!!! I would do it myself but I'm actually happy with my hinge and have to many other projects in the pipeline at the moment.
Apart from magnetic tape, we can also consider velcro/hook & loop
just stick a little at the back of the screen and the upper part of the keyboard
not too much to avoid noise/falling hair/forceful push
just the amount that keeps the screen in position anytime will do
just been using google skymap and I've noticed there is something rattling inside my transformer!!!!!!
is the back removable? anyone spotted a way something could have got inside? or is it something broken inside?????
its not been dropped or anything ........ and I've only just started noticing the noise .....
you sure it isn't edge creak? if it really is ratteling return it.
not a creak. something moves inside the unit from one end to the other. only started tonight. thing is I have no light bleed no sharp edges ....... don't know if its just something got in through a gap somewhere or something snapped off inside
My opinion would be return it, sure it could be harmless but it's still a faulty product. It could also **** up your device later on or be a sign of more ominous things.
I know you are right .... but I bought it from comet and it took long enough to arrive so god knows how long a replacement will take
and sods law ill get light bleed or gaps or sharp edges next time
ill ring comet tomorrow
wilbur-force said:
just been using google skymap and I've noticed there is something rattling inside my transformer!!!!!!
is the back removable? anyone spotted a way something could have got inside? or is it something broken inside?????
its not been dropped or anything ........ and I've only just started noticing the noise .....
Click to expand...
Click to collapse
If you enable and disable the camera it makes a sound. Try activating camera ....is that the same noise you hear?
wilbur-force said:
just been using google skymap and I've noticed there is something rattling inside my transformer!!!!!!
is the back removable? anyone spotted a way something could have got inside? or is it something broken inside?????
its not been dropped or anything ........ and I've only just started noticing the noise .....
Click to expand...
Click to collapse
If you enable and disable the camera it makes a sound. Try activating camera ....is that the same noise you hear?
I know there are 2 openings right under the LCD itself cover. On the left hand side there is tow half inch hole under the LCD, if you take a piec of paper and insert it at the left hand edge and sort of drag it down...you'll know where the gaps are, but this is too small for anything to go through...maybe these are air vents.
its not the camera. I'm sat here web browsing and if I rotate landscape and portrait it hear something moving.
not sure I follow what you mean about the holes. wondering if something has got in through the keyboard dock points???
It's probably baby teeth. I hear they're good luck.
stuntdouble said:
It's probably baby teeth. I hear they're good luck.
Click to expand...
Click to collapse
Or the hamster fell out of the wheel
Sounds like another asus QC story, i wonder what crazy stories will come next?
Good luck with getting it resolved.
Photo cameras have mechanical orientation sensors that are making a noise when going from landscape to portrait but they are very quiet and I doubt they are used in phones and tablets which have accelerometers.
this was something definitely moving about..... ie traveling the length and width of the unit.
its stopped now though so I haven't got a hope in hell of persuading comet that "my unit was rattling, honest! "
don't worry about persuading comet...just give them a call and they'll replace it...
I asked for a replacement yesterday..and I believe the support guy had no idea what a light bleed is, and he tole me parcelforce will come my home with a new TF on Monday..
damn.... after a week of no rattling its started again. I'm convinced its just a fragment of plastic or something and apart from that the unit is perfect .... no light bleed or dead pixels or dust ....
do I risk exchanging?
I wonder how easy it is to get the back off?
wilbur-force said:
damn.... after a week of no rattling its started again. I'm convinced its just a fragment of plastic or something and apart from that the unit is perfect .... no light bleed or dead pixels or dust ....
do I risk exchanging?
I wonder how easy it is to get the back off?
Click to expand...
Click to collapse
You might try a magnet and see if you can move the fragment within the case. Of course, it could use aluminum screws but metal will have more mass than plastic. If it tends to roll easily, I would suspect a metal fragment.
levenite said:
You might try a magnet and see if you can move the fragment within the case. Of course, it could use aluminum screws but metal will have more mass than plastic. If it tends to roll easily, I would suspect a metal fragment.
Click to expand...
Click to collapse
That's a good way to screw up other components inside your device. I wouldnt do that if I were you.
lol, no, i think i will avoid the magnets thanks
.... sent from my shiny new keyboard that arrived this afternoon by the way
im trying to crack the transformer open and do u think the back is glued on or is it screwed on? im thinking theres probrably some screws behind the lable but cant seams to find anything here that wont scratch it to remove it. hit me up with ideas and hopfully I can post some kind of video on how to dissacemble the transformer.
It will most likely be fastened with screws. I think if it had been glue peoples cases wouldnt be 'creaky'. There were some pics on a Chinese site showing it open. I saved them to my pc, If I find them I'll upload.
Edit: Well I found them but they're not really showing the case. I'll attach them anyways and you can see if they help or not. It looks like once you get the bezel off the back just slides clean off.
Ok well scratch screws under the asus logo, thanks very much for those pics. I already have the screws out from the bottom. I'm guessing the back seals with some type of clips
Looking at there tools in second picture seams they used a guitar pic to losses it from its edges
cowballz69 said:
Looking at there tools in second picture seams they used a guitar pic to losses it from its edges
Click to expand...
Click to collapse
Maybe try a credit card?
Ha tore up my room looking for my guitar pic lol. Ill try my credit card
When in doubt use a hammer.
stuntdouble said:
When in doubt use a hammer.
Click to expand...
Click to collapse
Lol, tryed to use a credit card but its to thick, going to stop at the store tomorrow and pick one up
cowballz69, pm sent
If you have one, your best bet is a Stanley knife (boxcutter, I think you call them). Should be thin enough, you'll just have to be careful not to nick any internal crap.
If it were me, I'd use a scalpel, but I know most people don't have one handy.
ok well heres my mini review untill i get a guitar pick, i got the bottom half to crack open with a credit card(to thick but i did it), i was then able to slide the card from one end to the other. The plastic clips holding the metal are very very crappy. the metal was extreemly easy to bend and by just putting the card threw the bottom was enough to bend it. i was however; able to put it back together with out making it look as if i opened it, but u would need a ULTRA Thin piece of plastic to complete the mission(DO NOT USE ANYTHING ELSE BUT PLASTIC,,THE METAL AROUND THE EDGE IS SUPER FRAGLE). seams all ASUS does is pop the plastic backing in and screw the bottom and its off to who every buys it.
(Losining the bottom screws lowerd the light bleed that was there by 30% ( i was a full brightness and back screen and loosining the screwes made a big impact so the issue with the light bleed is to much pressure on those areas)
seams this is easy enough just need the right tools.
cowballz69 said:
(Losining the bottom screws lowerd the light bleed that was there by 30% ( i was a full brightness and back screen and loosining the screwes made a big impact so the issue with the light bleed is to much pressure on those areas)
seams this is easy enough just need the right tools.
Click to expand...
Click to collapse
Interesting. That seems to be the very spot where my screen has a little backlight bleeding. I'll try it out in a few minutes.
Youtube it
If this is the fix. A youtube vid would be awesome. Ready set go
paleridr said:
If this is the fix. A youtube vid would be awesome. Ready set go
Click to expand...
Click to collapse
thats not the only spot i have light bleed, i also have bleeding on the top portion and theres no screw to losen so must be on to tight from the inside. however this does prove that the bleeding is from pressure not the screen itself
You need these spudgers,
http://www.dealextreme.com/p/professional-premium-precision-phone-disassembly-tool-7-piece-set-23050
Get a few sets (if you're planning on opening up electronics on a regular basis). These are soft plastic, and will wear out after a few uses. You don't want to use anything harder like a knife, as then you will mar the 'lips' on the device shells. Aesthetics aside, that will show up as evidence of tampering, meaning goodbye warranty.
Most electronics use plastic snap-in clips to hold the shells, along with screws and possibly soft glue. Going slow will prevent the clips from snapping off, but not always.
You can find these same tools on Amazon and eBay. Just search on 'spudger', which is their name.
Use the guitar pick to get the initial crease, push one of the thicker wedges into the crease, and slide it along the seam. This assumes you've gotten all of the (hidden) screws.
e.mote said:
You need these spudgers,
http://www.dealextreme.com/p/professional-premium-precision-phone-disassembly-tool-7-piece-set-23050
Get a few sets (if you're planning on opening up electronics on a regular basis). These are soft plastic, and will wear out after a few uses. You don't want to use anything harder like a knife, as then you will mar the 'lips' on the device shells. Aesthetics aside, that will show up as evidence of tampering, meaning goodbye warranty.
Most electronics use plastic snap-in clips to hold the shells, along with screws and possibly soft glue. Going slow will prevent the clips from snapping off, but not always.
You can find these same tools on Amazon and eBay. Just search on 'spudger', which is their name.
Use the guitar pick to get the initial crease, push one of the thicker wedges into the crease, and slide it along the seam. This assumes you've gotten all of the (hidden) screws.
Click to expand...
Click to collapse
breaking a clip is def possible in this case
How did you get the screws on the bottom off? Do you have the right screw driver (any ideas where I can get one)?
jrac86 said:
How did you get the screws on the bottom off? Do you have the right screw driver (any ideas where I can get one)?
Click to expand...
Click to collapse
it's a torx.
jrac86 said:
How did you get the screws on the bottom off? Do you have the right screw driver (any ideas where I can get one)?
Click to expand...
Click to collapse
Use a Torx T6 bit.
When you opened it up, was there anything to suggest there was any way Asus would know you had opened it up please (if you hadnt bent the bezel ofc) if you needed to send it back under warranty for some reason?
opening is not recomended threw my experiance * I used the thinnest guitar pic today*,and the metal around the edge;any slight flex and it ends up staying that way and wont go back on straight no matter how carefull u are, also the clips that hold the plastic back to the bezil is ULTRA CRAPPY to a point u have a 50 50 chance of it not holding the plastic cover anymore. ON the plus side; if u loosen the bolts in the bottom, u can relieve the light bleed there. so reguarding the light bleed its best to just send it back to ASUS to get it fixed.
MY Next step is having ASUS fix my light bleed on my own tablet and not have them give me a replacement.
I will be posting a before picture of the light bleed when i send it out , and a After picture on when i recieve it back from them. good idea??
My battery cover is a little loose all of a sudden. at the bottom it now moves a little. When I squeeze (lightly, normal use amount) the phone at the bottom kinda clicks. Anyone else have this issue?
Yes. I called HTC and they're replacing it. But for now what you can do is put paper inside the case
Sent from my HTC Sensation 4G using XDA App
Yeah, several other people reported this problem on a Dutch forum. People should not open the backcover unless they really have to. After opening the cover a few times the cover is getting loose and starts to crack when you press it.
okay so I have the same problem, should I be worried or is it just the case with all sensation handsets ?
Take the cover off and press the battery. I think that's what it is...or maybe both.
Sent from my HTC Sensation 4G using XDA Premium App
secano said:
Take the cover off and press the battery. I think that's what it is...or maybe both.
Sent from my HTC Sensation 4G using XDA Premium App
Click to expand...
Click to collapse
I don't think that's it, the battery is fitted normally, and I've just tested it with battery removed, it does the same thing, I should mention that it isn't really that obvious, but it's an annoyance nonetheless, such an expensive phone to have a glitch like that.
can anybody confirm that it does loosen after some time of usage, I mean did it came like that out of the box or was it getting loose with time?
I just noticed this on mine this morning , will steal a new cover soon
****ttttt let me check mine lol
...same here, at the right bottom corner!!!!
...and I agree, tooooo expensive phone for such a glitch!
Spekko said:
I just noticed this on mine this morning , will steal a new cover soon
Click to expand...
Click to collapse
I went to a tmobile store to see if they'll let me switch. The rep told me thy they can't switch cuz its an htc problem. Then he got curious and pulled out his sensation to see if his had it...
He looked so sad lol I just got off the phone with htc and my replacement cover is shipping soon and if the second one is defective then I have to send in my whole phone so they can check it out. You guys should call htc I'd you already haven't
I fixed mine by adding some paper to the back.
http://forum.xda-developers.com/showthread.php?t=1215096
Hey first post here! Signed up just to have my say on this issue, just as i did with the android central forum.
Also posted this on the android central forums...
Got the creaking here also, definitely a design flaw. Being obsessive with my devices i couldnt live with it!
I do not recommend putting paper in the cover to fill the gap, as this is just expanding the cover further making it even MORE loose when the paper is not in there. Also i wouldn't recommend it because the paper pushes the back cover out a little more, you may loose a connection for the ground. Which is the little metal springy thing, half way up the right hand side. Obviously its not a good idea to 'push' the cover further away from this ground spot. I have heard that people have had issues with screen responsiveness due to a static build up from not grounding properly.
What i did to fix this problem was a bit of a kitbash of sorts.
Mine was creaking on the bottom right area, like most. The problem is there is too much play between the little black catches on the battery cover and the latch on the handset. Instead of filling up the gap between the phone and the cover (Ala paper, card in the cover) I closed it!
What you need to do is get some very thin plastic film. Like that on kids toy packaging etc. Not the thicker stuff though. This stuff would be under 1mm thick. It came as a viewing window in the box my new wallet came in. So you can sorta imagine what im talking about.
I cut a piece about 10mm long and as wide as one of the two little black catches. I applied a VERY thin coat of super glue to one end of the film. Just enough to cover the area under the catch. Then i carefully placed the film with the superglue on it under the catch, and then quickly applied some pressure to it with some tweezers. Then i carefully cut the excess off with a pair of finely tipped nail scissors.
The result is that it now PULLS the screen/phone INTO the cover more by making the little black catch thicker. Not the opposite (paper method), which pushes the cover out, creating a further problem of adding more paper under the cover over time as the cover expands/loosens to compensate. Not to mention a possible grounding loss and resulting damage.
Hope this helps some people that have had multiple replacements or could not be bothered replacing for such a cosmetic issue. (Like me). It definitely works, just got to get your surgeon on and be accurate with your placement of the film.
Apply this to what ever side creaks the most, and bam its gone. Nice. Solid phone... again.
If anyone wants more specific details etc, im all ears.
Regards,
Matt.
MrSoulSOng A video explaining this fix would be appreciated ^_^ cuz I didnt buy my phone from here and I still gotta wait for about a month to send it to the shop to fix or get a replacement
...just an update...after buying new back cover from no1tech (that was month and a half ago...) there's no loose spots, no creacking...!
Very satisfied now I am. Finally phone feels and looks like it should be - beast in compact housing!
I have the very same problem too. VERY annoying
well I had the same problem however what i did was that on the back cover inside of it I put some black electric tape on to the sides that creak (next to the sides and the clips) and when I put the cover back on there was no creaking at all. figured it wont interfere with the single because people put cases on the back all the time plus its electric tape meaning it'll prevent from short circuits and I don't think there should be any overheating issue as its a very small quantity.
I'm asking this because my GPS is frankly awful and I accidentally broke the GPS cover by melting it when solder was being put on the existing contacts.
Does anyone know where to get the Inspire 4G GPS covers? The Desire HD ones are nearly identical, but they lack the hole for the noise canceling microphone.
When the Inspire first came out there were issues with the covers and HTC was shipping them out for free. Do a search in the forum. Contact HTC and tell them your covers are trashed.
I have no experience with this supplier...
http://www.all4cellular.com/htc-inspire-4g-battery-door-and-sim-cover.html
Picsman said:
I have no experience with this supplier...
http://www.all4cellular.com/htc-inspire-4g-battery-door-and-sim-cover.html
Click to expand...
Click to collapse
Those are different. The cover I'm looking for is where the LED flash is. You have to pop it out with a tool reaching into the battery compartment.
I bought a set of the 3 covers on the phone, hopefully the GPS cover is the right one and has the hole for a noise-cancelling mic.
Hunt3r.j2 said:
has the hole for a noise-cancelling mic.
Click to expand...
Click to collapse
One word- dremel
try ebay you can get anything on there
kimtyson said:
One word- dremel
Click to expand...
Click to collapse
I'm frankly not even sure if the Desire HD variant of the GPS cover is made in such a way that permits this to be done.
Just did some looking around and some experimentation. I think this is going to be the best course of action for an OEM-looking hole:
1. Find a paper clip that will cleanly go through the existing noise canceling hole. It shouldn't be too thin, but just about right.
2. Straighten out the paperclip so you get a nice straight section to work with.
3. Get a lighter or a gas stove and heat up the paper clip for a few seconds to get the straight section heated up enough to let you punch through the plastic without melting it completely.
4. There's a hole in the clear plastic where the LED flash connects to the black plastic, where the Inspire has a hole that goes cleanly through for it's noise canceling mic. Try to drive the paper clip wire clear through the hole, and make it straight. Hopefully there's enough heat for you to get a clean, smooth hole that looks like OEM.
I've taken a look at the dremel tools I have, and they are all definitely way too big for making a hole like this.