Hey guys,
I'm going to try to make a long story short.
I have two routers in my home and decided to run the second one as a wireless repeater bride. Both routers run DD-wrt.
I successfully setup the second router as the repeater bridge and proved that it works by browsing wifi connected to this router with my Original Droid, Ipod touch, and laptop computer.
However my DC will not.
It will connect to the router, obtain an IP, and report that it's connected, however it cannot access the internet. Mac filtering is not enabled at all.
I was initially running Gummy 1.9RC2 GB with EP1Q, Then wiped and flashed Gummy 2.0 Froyo with EE4, both with the same results.
Any idea's guys?
It's probably confuzzled. I would set them as independent routers with different AP names and just have them both saved.
Sent from my Droid Charge running GummyCharged 2.0
tsitalon1 said:
Hey guys,
I'm going to try to make a long story short.
I have two routers in my home and decided to run the second one as a wireless repeater bride. Both routers run DD-wrt.
I successfully setup the second router as the repeater bridge and proved that it works by browsing wifi connected to this router with my Original Droid, Ipod touch, and laptop computer.
However my DC will not.
It will connect to the router, obtain an IP, and report that it's connected, however it cannot access the internet. Mac filtering is not enabled at all.
I was initially running Gummy 1.9RC2 GB with EP1Q, Then wiped and flashed Gummy 2.0 Froyo with EE4, both with the same results.
Any idea's guys?
Click to expand...
Click to collapse
can't you connect to the main router is it n if so your signal should be good
Sent from my SCH-I510 using XDA App
That's what's so weird, it will still connect to the 1st router and browse...
How can all my other gadgets connect to either router and browse, yet my DC can't?
It's gotta be something on the DC, but I don't even know where to start on Android. LOL
that is wierd although I had a similar issue with the droid x3 it wouldnt connect to my home router which was n but connected to my work router which was b/g try forget network in the wifI settings then restart the router and try again
Sent from my SCH-I510 using XDA App
but wait for more opinions before you take my advice
Sent from my SCH-I510 using XDA App
Yeah, Already tried that too! but thanks!
I should of mentioned, both routers are set for G only.
tsitalon1 said:
Yeah, Already tried that too! but thanks!
I should of mentioned, both routers are set for G only.
Click to expand...
Click to collapse
welcome and I debt know then I normally try every method I can and things get fixed its a process
Sent from my SCH-I510 using XDA App
Not many routers support wrt, what equipment are you using? Airport devices? Hawking tech? Other? Reason I ask is, in my experience, apple equipment will perform this task the best.
It may sound odd but there can be a few things causing this problem.
What I would do first is connect the DC to the second router, then try to ping the router. There is a free app on the market to ping. If you can ping the router then you might have a dns issue, if you can't ping the router, then the second router is probably limiting the dhcp pool, on which you can log into the router and open this up.
If you MUST user a wireless repeater bridge, please test with a laptop instead of the phone to see if the problem is isolated.
If you need to boost wireless signal, I highly suggest getting a third router and setting it up as an AP and wire to the 2nd router (configured as client bridge) OR set up WDS. WDS is much better than wireless repeater mode, but setup is a bit trickier. There is a ton of help on WDS on the net. Wireless repeaters are problematic; I urge you not to use wireless repeater mode.
What kind of router is it? I had to return a new fancy dual channel N Netgear router due to compatability issues with some devices.
Related
What routers do you all use with your G tablets? Are there any to completely avoid?
Thanks, WAD
I dont think routers will be a problem. I have tested mine with linksys and d-link and so for so good. Those are the only two I have. Having an N router would be nice for the distance.
Any n1 router. I don't even waste my time with less. I like netgear
WantADroid said:
What routers do you all use with your G tablets? Are there any to completely avoid?
Thanks, WAD
Click to expand...
Click to collapse
I am using Trendnet wifi router with WPA PSK; works fine without any issues.
Apple Extreme Base Station, no probs...
I'm using the one Verizon Fios gave me which is wireless N. My gtab flies with wireless N. If I didn't have one already, I would go for any wireless n router that isn't made by Belkin. Those are the only routers I ever had problems with.
Thanks
Thanks for the replies, I bought a netgear n router to replace my old netgear b. Now I just need to go pick up my G tab.
darkness77 said:
I dont think routers will be a problem. I have tested mine with linksys and d-link and so for so good. Those are the only two I have. Having an N router would be nice for the distance.
Click to expand...
Click to collapse
Ditto. I have a mix of Linksys (WRT610N) and DLink (DIR-825 and DAP-1522) routers and APs. No issues with connectivity or speed.
One little annoyance. The gtab doesn't recognize that I moved from one router to another in the house like my Nexus One does (where it automatically switch to the most powerful signal even though there is a signal present on the existing WIFI connection). I have to manually reconnect the WIFI connection to the other router.
I have an Asus WT500gP v2 running DD-WRT and I've had no issues either.
I use a D-link 625 at home, no issue, also at varrious homes of friends and family as well as public hotspots...i.e. barnes and noble,starbucks,culvers...Some with encryption, others open, or mac filtering, no issues on any of them.
I have Edimax BR-6324nL router which is Wifi-N tecnology capable, But my Inspire is unable to connect to this router if I set it up to N only. It just connect to the previous tecnologies like G at 54MBps.
When the router is set up to N only my network appear in my inspire but it just say connecting and then disconnected.
Just with this router or you don't see other N wifi neither? What radio do you have?
Sent from my HTC Inspire 4G using XDA App
elbermu said:
Just with this router or you don't see other N wifi neither? What radio do you have?
Sent from my HTC Inspire 4G using XDA App
Click to expand...
Click to collapse
I haven't tried with another router, all router I have access to around here are B/G only. I have a Wireless USB adaptar that is N, So I will connect it in AP Mode, and will try with it.
I Have the Android Revolution HD 6.3.1 with the 12.65.60.29_26.14.04.28_M Radio recomended by mike1986.
Problem solved. I tried with my USB adapter and it wasn't able to connect in N only mode. I sent an email to Edimax and they give me a solution. It was password encryption problem. N standard need the WPA2-AES to work fine. I just set the password to this standard and problem solved.
Wifi-N standard is working fine, but I just get 65/72Mbps. and signal coverage is not what I expected. it is less as what I got with my Aspen which is just B/G standard.
if anything else is connected to this router via b or g it will scale the speed down to them. Also how are you testing the speeds of your connection?
I have my N router setup for backwards compatibility and the best I connect at is 65mbps. With wireless N, speed is faster, but range is shorter, it does not penetrate walls as well, and it is more susceptible to interference. I had to move my router to a more centralized location and I have not had problems since.
Sent from my HTC Inspire 4G using Tapatalk
Darunion said:
if anything else is connected to this router via b or g it will scale the speed down to them. Also how are you testing the speeds of your connection?
Click to expand...
Click to collapse
Nothing else with backward standard is connected, since I have it set up to N only. But the thing is that I have more or less the same signal coverage than before when I had my Aspen which is B/G only. In any case I should have more coverage that what I had with the G standard with my Aspen, and it is practically the same or less. According with Edimax website in N standard the speed is up to 6 time and coverage up to 4 times.
The speed is showed in the Wi-Fi connection in the device. Just go to wi-fi settings and hit the active wi-fi connection and a pop-up windows will appear with the info.
But according to my research, the speed limitation to 72MB is due to the 20mhz of channel width of the Inspire. I connected a USB Wi-Fi adapter and it is at 40mhz and it connect at 135MB.
Anyway my major concern is not about connection speed is about signal coverage that is not what I expected. Anyway I will try with another wireless device to see if the speed range issue is the router or my Inspire.
Sent from my Inspire 4G using XDA App
fernandezhjr said:
I have my N router setup for backwards compatibility and the best I connect at is 65mbps. With wireless N, speed is faster, but range is shorter, it does not penetrate walls as well, and it is more susceptible to interference. I had to move my router to a more centralized location and I have not had problems since.
Sent from my HTC Inspire 4G using Tapatalk
Click to expand...
Click to collapse
uhh. It is not supose that the N standard range be shorter. As far as I am aware of, this is in the 5GHZ signal, but my router only work at 2.4ghz
Sent from my Inspire 4G using XDA App
what channel is your WiFi running on? for some strange reason if i run mine on a channel >10 my Inspire doesn't pick it up...any other channel and it's good
nehrou said:
what channel is your WiFi running on? for some strange reason if i run mine on a channel >10 my Inspire doesn't pick it up...any other channel and it's good
Click to expand...
Click to collapse
Channel 11
So I know it's been asked a few times but not with an airport extreme.
I have a 4g LTE phone (Galaxy Nexus) and I am paying a lot for my phone bill and my cable modem bill.
Has anyone tried this?
Galaxy Nexus ----> Airport Extreme Router -----> PC/Mac clients
If so how? I tried to do extend network but it wasn't able to be extended.
Thanks in advance.
Not really ... but what you can do is that get a wireless bridge and do It that way
Sent from my Galaxy Nexus using Tapatalk 2
Considering that AP is made by Apple, I think it's pretty safe to say in the words of bender "you're boned", but..
I run a Linux router on amd64 hardware as my fileserver/webserver/NAT/proxy/vpn "home office gateway extrodinare"... It has one interface going to a cable modem, and when that goes down (which luckily is almost never) I just grab a droid, plug it in via USB, tether, and switch the WAN interface to usb0, call the cable folks, and forget about it for a while. As openvpn is going to tunnel my traffic to a datacenter regardless, it's completely transparent -- Not like the path to the DC matters
Yes you can, depends on what flavor of android and what phone you have..
Take a look at this Youtube video
youtu.be/QD5VaRjLQqE
When they say you need a gtx600 or above and a wifi setup and that the streaming is local I assume we can run the pc through our router right? The connection doesn't have to be directly from the pc to the shield does it? I'd rather not have to buy a wireless card for my desktop.
Thats how I took it. They never mentioned needing a wifi card on your pc.
in general streaming uses specific paths within windows/pc and your router to get to other devices. normally just about anything network based is either/or. however it gets a lot more complicated when you are trying to share between more then one router. im pretty sure it will be both. but if one was to be restricted, i think it would be wired only, and wireless wouldn't work.
kieso said:
Thats how I took it. They never mentioned needing a wifi card on your pc.
Click to expand...
Click to collapse
Only need to share a router. So unless you have some really crazy home network setup, it'll work.
Oh, and I believe the requirement is GTX 650 or above, not 600.
Guess I have some crazy LAN setup then, because I don't have a router.
chevyowner said:
Guess I have some crazy LAN setup then, because I don't have a router.
Click to expand...
Click to collapse
If you're directly connecting all your machines straight to the internet with no NAT, that is a crazy (and fairly unsafe) network setup. These days, most internet providers have a built in router and often Wi-Fi access point in the device they provide you.
Sent from my HTC One using XDA Premium HD app
agrabren said:
If you're directly connecting all your machines straight to the internet with no NAT, that is a crazy (and fairly unsafe) network setup. These days, most internet providers have a built in router and often Wi-Fi access point in the device they provide you.
Sent from my HTC One using XDA Premium HD app
Click to expand...
Click to collapse
My DSL modem (one port) has NAT, a firewall, and dhcp. After that I have 2 switches, a wifi ap and computers.
chevyowner said:
My DSL modem (one port) has NAT, a firewall, and dhcp. After that I have 2 switches, a wifi ap and computers.
Click to expand...
Click to collapse
The DSL model is acting as a router (with NAT support), albeit a 2-port one (one on the DSL side, one on your network side). This is similar to my work setup.
So, I've just spent the last few hours watching football and reading through a bunch of threads regarding WiFi connection issues with the N5. Well, here's another thread about a specific issue. I'm not seeing anything over 54Mbps connection to my Netgear R6200 with firmware V1.0.1.48_1.0.37. I'm connecting to the 5GHz SSID, I'm getting a solid 300Mbps connection on 3 other 5GHz devices (my laptop, desktop with USB WLAN adapter and the wife's laptop), my freebie Samsung Galaxy Victory is even mocking me, connecting to the 5GHz SSID at 135Mbps! The N5 just refuses to connect at anything above G speeds, nevermind AC speeds. I've done a factory reset, not restoring backed up data, I've tried disabling mobile data when connected to WiFi, I've tried every 5GHz channel, I've restarted the device, I've even tried using the 2.4Ghz SSID. Nothing. I'm about 8 fee from the router, no walls between me and it. Actually, I'm staring right at it as it sits there, chuckling at me.
Anyone have any ideas? If it's the router, then fine...should I buy the Asus to get true AC speeds from my N5? It matters to me for internal video streaming from my HDHR, and ripped blue rays, moving large files back and forth and other bandwidth-critical activities. For basic web surfing, it's not a big deal at all.
Well my N5 right now is connected at 72Mbps (2.4GHz) and 150Mbps on 5GHz, so it's not limited to 54Mbps...though why yours is I have no clue.
Sent from my Nexus 5 using Tapatalk
beaver2233 said:
Well my N5 right now is connected at 72Mbps (2.4GHz) and 150Mbps on 5GHz, so it's not limited to 54Mbps...though why yours is I have no clue.
Sent from my Nexus 5 using Tapatalk
Click to expand...
Click to collapse
What router do you have?
That's strange sounds like you tried everything on top of my head did you try selecting 5 ghz only through advanced Wi-Fi?
Mine connects at 292 on Asus AC66u
Sent from my Nexus 5 using xda app-developers app
puska said:
That's strange sounds like you tried everything on top of my head did you try selecting 5 ghz only through advanced Wi-Fi?
Mine connects at 292 on Asus AC66u
Sent from my Nexus 5 using xda app-developers app
Click to expand...
Click to collapse
Yup, I tried 5GHz only. Hmmm, I may have to look into that router. The R6200 is a decent AC router though, but it would not be the first time that different manufacturers have taken different directions with a proposed standard.
Go to Wifi go to settings Uncheck Wi-Fi optimization
it will make it go faster (with a heavier battery drain)
markdapimp said:
Go to Wifi go to settings Uncheck Wi-Fi optimization
it will make it go faster (with a heavier battery drain)
Click to expand...
Click to collapse
Yup...forgot to mention...did that as well. It's maddening! Thanks though!
ghostlobster said:
What router do you have?
Click to expand...
Click to collapse
I have the netgear N600. So it's only N compatible, not ac
Sent from my Nexus 5 using Tapatalk
Look in your router for a WiFi power saving mode it shows when my device is idle for 5 mins the nexus 5 drops power slightly to the WiFi
Sent from my SCH-I535 using Tapatalk
Heres my Router
ghostlobster said:
So, I've just spent the last few hours watching football and reading through a bunch of threads regarding WiFi connection issues with the N5. Well, here's another thread about a specific issue. I'm not seeing anything over 54Mbps connection to my Netgear R6200 with firmware V1.0.1.48_1.0.37. I'm connecting to the 5GHz SSID, I'm getting a solid 300Mbps connection on 3 other 5GHz devices (my laptop, desktop with USB WLAN adapter and the wife's laptop), my freebie Samsung Galaxy Victory is even mocking me, connecting to the 5GHz SSID at 135Mbps! The N5 just refuses to connect at anything above G speeds, nevermind AC speeds. I've done a factory reset, not restoring backed up data, I've tried disabling mobile data when connected to WiFi, I've tried every 5GHz channel, I've restarted the device, I've even tried using the 2.4Ghz SSID. Nothing. I'm about 8 fee from the router, no walls between me and it. Actually, I'm staring right at it as it sits there, chuckling at me.
Anyone have any ideas? If it's the router, then fine...should I buy the Asus to get true AC speeds from my N5? It matters to me for internal video streaming from my HDHR, and ripped blue rays, moving large files back and forth and other bandwidth-critical activities. For basic web surfing, it's not a big deal at all.
Click to expand...
Click to collapse
It's certainly not the N5, I have a Netgear D6300 router and my N5 is connected at 433Mbps on the 5GHz band which seems to be the maximum link speed for the device (my HTC One also connects at 433Mbps max). My desktop and laptop connect with a max speed of 866Mbps.
rider5512 said:
It's certainly not the N5, I have a Netgear D6300 router and my N5 is connected at 433Mbps on the 5GHz band which seems to be the maximum link speed for the device (my HTC One also connects at 433Mbps max). My desktop and laptop connect with a max speed of 866Mbps.
Click to expand...
Click to collapse
What ISP?
Sent from my Nexus 5
PhilipTD said:
What ISP?
Click to expand...
Click to collapse
It's nothing to do with my ISP, those are the connection speeds between my devices and the router and nothing to do with the router connection speed to the outside world.
rider5512 said:
It's nothing to do with my ISP, those are the connection speeds between my devices and the router and nothing to do with the router connection speed to the outside world.
Click to expand...
Click to collapse
Well, my ISP has different plans with different maximum speeds. I have the fastest one they offer, and it's only up to 50Mbps.
Sent from my Nexus 5
PhilipTD said:
Well, my ISP has different plans with different maximum speeds. I have the fastest one they offer, and it's only up to 50Mbps.
Sent from my Nexus 5
Click to expand...
Click to collapse
The OP's question was about the link speed between his N5 and his router, it has nothing at all to do with whatever plan you have with your ISP
rider5512 said:
The OP's question was about the link speed between his N5 and his router, it has nothing at all to do with whatever plan you have with your ISP
Click to expand...
Click to collapse
Ah, correct. Sorry.
Sent from my Nexus 5
beaver2233 said:
Well my N5 right now is connected at 72Mbps (2.4GHz) and 150Mbps on 5GHz, so it's not limited to 54Mbps...though why yours is I have no clue.
Sent from my Nexus 5 using Tapatalk
Click to expand...
Click to collapse
Ditto. I get same results on same bands. Asus RT-N66U router.
Thanks for all the input folks. From what I'm hearing it looks like something screwy with the router and the N5 combo. Not surprising but disappointing. Was kinda hoping that some would see this and chime in with "oh, I have that router too and just changed this setting and bam!". Oh well....time to look for a new router. :fingers crossed:
Got same 433 mbps as rider Which He says should be max for our device. Thought I saw only 300 not that it makes any difference.
But Op is there a way to try connecting to some other 5ghz or same router some place else to see if it's because of the phone your router or combo of two
try 'FORGETTING' All your wifi settings, disable data, reboot
login 5g or maybe it's better to use WPS
test, good luck it worked for me
I have precisely the same problem using a Netgear R7000. My other devices connect at up to 450Mbps but my Nexus 5 won't connect above 54Mbps. Very odd. If anyone has found a solution or even an explanation I'd be happy to hear from them.