Related
ok..recently aquired this phone...
I've discovered that there is no sound from the speaker at all, no mp3 alarm ringtones .... I've used the slider on the side with no luck, and also tried changing the profile, volume control ect...no luck
Does anybody fancy talking me through any possible fixes for this...
Somebody suggested a hard reset?.... Any suggestions on doing this?...
Is this likely to be a software / registry change to fix this, or is it likely to be a case of sending it back for repair?... I'm sure its under warranty... but if its not, any suggestions on where I could take / send for repair?.... I'm in the Beckenham, bromley, south London region....
I have a basic understanding of pc's, but am not confident of doing registry changes without step - by - step instructions....
Anybody fancy a challenge?.... Thanx in advance...
PS.. just curious...any reason why this forum site is very simular layout to AV Forum site?....
Bump......
Try a Hard Reset first :
festermania said:
To perform a hard reset :
Press and hold the GPS/MESSAGING and INTERNET EXPLORER buttons, and at the same time, use the stylus to press the RESET button at the bottom of your device.
Release the RESET button, but continue pressing the GPS/MESSAGING and INTERNET EXPLORER buttons until you see this message on the screen:
"Release the buttons, and then press SEND on your device to perform the hard reset, or press any other button to cancel the reset."
To see bootloader page :
Hold power button + Camera button and push reset button with stylus wait 3 seconds and then release the reset button but keep pressing the power button + camera button u will be then in bootloader page
Click to expand...
Click to collapse
...did you go to Start Menu->Settings->Personal Tab->Sounds & Notifications to make sure that you've Enabled Sounds for Programs? a Hard-Reset certainly seems to be the option of choice here if nothing else is working. you can perform the Hard-Reset by selecting Start Menu->Settings->System Tab->Clear Storage and then follow the prompts to complete the process.
Nope...hard reset didnt work...just to say... I can hear through the earpeice when speaking in a phone conversation...just no other sound at all... even tried the option for beeps or clicks when using the keypad and still no sound... Also...that bootloader option...It just takes me to a screen with 4 different coloured stripes and some writing..I'll try it again and post what it says, but basicly it just freezes, then I have to do a soft reset to get the phone back on....
Bumpity bump....
m3uch4 said:
Press and hold the GPS/MESSAGING and INTERNET EXPLORER buttons
Click to expand...
Click to collapse
Please remember that the Orbit II does NOT have these buttons!
Update...
I've done another hard reset using this method....
1) Get your stylus and place it in the hole next to the USB port, BUT DONT PUSH! Just get it ready but dont actually push the button inside the hole.
2)Place your fingers on the Windows and OK buttons
3)Press and hold the buttons, dont let go.
4)Stright away push the stylus into the hole and press the button inside. You can let go of the stylus once the button inside has been pushed
5)Keep holding onto the Windows and OK buttons
6)After 5 seconds let go of the Windows and OK buttons
7)If asked to press SEND, just press the green pickup call button.
....
And still no sound!....
Any ideas?
Yes that's the correct procedure, strange about that sound though.
What ROMs it running?
Any clue about what it might be?....
hang on I'll find out........
ROM Version. 1.25.206.3 WWE
Is that the latest Rom..Would it be worth updating if there is a newer version?....
Is that an official ROM or cooked?
I think its official...
you could have a hardware problem...i would have sent it back for a replacement 3-4 days ago!
I cant, bought it second hand. Will take it back for refund if I cant get it fixed...just thought it might be a common problem with a easy fix!...
i believe you've tried most options without any success. the only other options are to open it up and see if maybe the speaker has been dislodged. not sure how easy that would be. good luck!
OK.... thanx anyway!... Damned tiny little screws inside...cant get to the speaker... Ok...off to the shop it goes!
No sound
I had this problem on another HTC device 'the Kaiser' and was informed some specific Roms are not compatible with the radio on the device ( does your device have the original Rom? ) Flashing a new may have caused this problem.
I'm trying to find out if anyone knows how to hard reset this phone with the physical keys. My phone has stopped booting all the way and the screen doesn't respond. I need to wipe it before returning it, but cannot get into it enough to clear storage.
Thx
Hard Reset with physical buttons
rsamson said:
I'm trying to find out if anyone knows how to hard reset this phone with the physical keys. My phone has stopped booting all the way and the screen doesn't respond. I need to wipe it before returning it, but cannot get into it enough to clear storage.
Thx
Click to expand...
Click to collapse
I need the same advice
See enclosed page from Incite manual.
Lg incite hard reset
To perform a hard reset
• A Hard Reset should only be performed after all other trouble shooting options have been exhausted.
After a hard reset, the device is restored to its default settings - the way it was when you first
purchased it and turned it on. Any programs you installed, data you entered, and settings you
customized on your device will be lost.
1. Power the device ON
2. Tap Start > Settings > System tab > Clear Storage.
3. Enter 1234 for the password twice.
4. Press Enter.
5. Select what to reset.
You have to enter your password and confirm again for hard reset. However when you forget your
password, the only way to hard reset the device is via the hard key sequence.
1. Power the device OFF.
2. Press and hold the following hard keys in sequence.
left side - down rocker button - right side camera button - front right phone button
Keep pressing keys until your LCD screen turns on.
Align screen will appear if you success hard key reset.
1. Remove & replace the battery 1st
2. Hold down at the same time:
Volume Down + Camera + Power until the Windows Mobile screen appears.
DONE
dwny said:
1. Remove & replace the battery 1st
2. Hold down at the same time:
Volume Down + Camera + Power until the Windows Mobile screen appears.
DONE
Click to expand...
Click to collapse
Fail. Any other ideas?
Used it today, worked fine.
Works...
brogrimm said:
Fail. Any other ideas?
Click to expand...
Click to collapse
Confirm it works....Make sure the sequence of keys is ...volume....camera....power key. Hold till WM 6.1 screen comes on.
Don't forget to put battery back before reset
i am also unable to perfor m a hard reset doing the key sequence..please help!!
Another solution
If you followed the steps above and the phone is still not hard resetting, you can try to enter Emergency Download mode and update the ROM. My phone would not hard reset and just kept getting stuck at the AT&T logo screen. I downloaded the V10X ROM update from the LG website and followed the instructions contained in the update. After the update, the phone works perfectly.
chappatti said:
Confirm it works....Make sure the sequence of keys is ...volume....camera....power key. Hold till WM 6.1 screen comes on.
Don't forget to put battery back before reset
Click to expand...
Click to collapse
and until green right goes off. (while WM green screen on)
The process works without flaw unless you are not properly holding the buttons or for the right amount of time. I have posted the directions in a tutorial and you are welcome to take a look, try it and I am sure if you follow it, it will work for you.
1. Resetting Device
2. Flashing Original ROM
I have been hard reset my phone!
I now,Align Screen not working.And i can't continue setup my phone!
Help me!!
niindark said:
I have been hard reset my phone!
I now,Align Screen not working.And i can't continue setup my phone!
Help me!!
Click to expand...
Click to collapse
i am in the same situation. how do you get the incite in emergency download mode?
ditto
josefcrist said:
i am in the same situation. how do you get the incite in emergency download mode?
Click to expand...
Click to collapse
me to, just got mine yesterday
Hi all,
Perhpas this has been answered before, but I couldn´t find any related thread.
My Rapahel is turned on but can´t see anything on the screen! is totally black.
I know it´s turned on because I can up or down the volume key and I hear the sound and feel the vibrate.
Yesterday was ok, nothing new installed but today I just pressed the power button and nothing!!
This happened me before on Universal, problem was that in some way the phone change itself the brightness to cero.
If I conect to wall charger nothing happens also, not any sign that device is charging.
But still can see something. Now on my Rapahel I cant see anything?
Any help would be much than apreciated please!!
Thanks,
I would
1 softreset
2 hardreset
3 rma
Rudegar said:
I would
1 softreset
2 hardreset
3 rma
Click to expand...
Click to collapse
thnaks,
soft reset done: nothing
hard reset done: nothing
sorry, what is rma?
Any other advice?
help please!
Hey masters!
A light would be great here!
Sorry to insist!
orb3000 said:
thnaks,
soft reset done: nothing
hard reset done: nothing
sorry, what is rma?
Any other advice?
help please!
Click to expand...
Click to collapse
Not a master, but still try to help:
What happend during the soft or hardreset, is the screen showing during the booting ?
How did u do the hardreset, by holding keys ?
After the hardreset u have to get the screen aligned how did u get after that point ?
Help!
Ok this is what I did:
When sof reset not any screen was appearing during the process.
Yes tryed the hard reset presing volume down the center button and the hole behind the charging usb and nothing happened
Snince then I can just hear the sound but nothing on the screen at all
Thanks for any advice!
orb3000 said:
Ok this is what I did:
When sof reset not any screen was appearing during the process.
Yes tryed the hard reset presing volume down the center button and the hole behind the charging usb and nothing happened
Snince then I can just hear the sound but nothing on the screen at all
Thanks for any advice!
Click to expand...
Click to collapse
Hard Reset the device:
This will wipe all the storage (not the sd card) and your device will be reset to default settings.
Hard reset (option 1)
1. Pull out the stylus.
2. With the device turned on, press and hold the VOLUME DOWN and CENTER buttons, then press the RESET button with the stylus tip.
3. Continue pressing the RESET, VOLUME DOWN and CENTER buttons until you see this message on the screen:
This operation will delete all your personal data, and reset all settings to manufacturer default. Press ?VolUp to restore manufacturer default, or press other keys to cancel.
Hard reset (option 2)
You can also use Clear Storage to reset your device back to factory default settings.
1. On the ?TouchFlo3D Home screen, slide to the Settings tab and then tap All Settings or goto Start and press Settings.
2. On the System tab, tap Clear Storage.
3. Enter “1234” and then tap Yes.
Hard reset (option 3)
1. Pull out the stylus.
2. Turn device OFF.
3. While pressing the CENTER button, turn the phone on with the POWER button.
4. Continue pressing the CENTER button until you see this message on the screen:
This operation will delete all your personal data, and reset all settings to manufacturer default. Press ?VolUp to restore manufacturer default, or press other keys to cancel.
This works on at least some Verizon CDMA phones on which option 1 will not work.
Hard reset (option 4)
1. Pull out the stylus.
2. With the device turned off, press and hold the VOLUME DOWN and CENTER buttons, then press and hold the POWER button.
3. Continue pressing the POWER, VOLUME DOWN, and CENTER buttons until you see this message on the screen:
This operation will delete all your personal data, and reset all settings to manufacturer default. Press ?VolUp to restore manufacturer default, or press other keys to cancel. (works with Alltel touch pro)
Click to expand...
Click to collapse
Ok this is out of the wiki, u see that all methods let u press the vol up button to really start the hard reset than. So on either method do the key presses, wait a while and then press the vol up to start the process.
Its a little try and error because u are not seeing the the actual message to press the vol up. but mybe thats worth to try until u get the point. I think option 3 is a good and easy one.
hopefully the hardreset works, maybe u can try to take a torch or bright sun light to get the display information, if the display itself is not broke u should see a slight shadow of what is written on the display. I had that problem with my wifes phone once and the information was the but its not a reflective display so it was very faint to see.
Finally tho, if all that fails:
RMA = Return merchandise authorization
It means a warrenty return.
It sounds to me like the lcd has croaked. If you dont have suitable warrenty / insurance i'd suggest ebay! i've just found a screen & digitiser for less than £25 (thats for a Raph 100, i honestly dont know if parts are the same on different raph models but i suspect they are)
Good luck!
Thanks a lot guys but nothing worked
I cant do any hard reset option but sound stills hearing perfect
I can understand why one day was perfect and next no screen!!
Can anyone confirm that the LCD Display+Touch Screen For HTC Touch Pro T7272 form the last link will work on my At&t version?
Any other advice?
Thanks in advance
orb3000 said:
Thanks a lot guys but nothing worked
I cant do any hard reset option but sound stills hearing perfect
I can understand why one day was perfect and next no screen!!
Can anyone confirm that the LCD Display+Touch Screen For HTC Touch Pro T7272 form the last link will work on my At&t version?
Any other advice?
Thanks in advance
Click to expand...
Click to collapse
Sorry to hear that nothing worked.
Not shure but if the phone fails to hard reset it is not only the screen that is broken ! Take this into account, do u still have warranty, maybe it is better so exchange the whole phone.
Well that is the problem
I live in other country so warranty is not valid here, and there is not a single place where I can take it to repair here
Very strange as one day was perfect ant the next day no screen!!
I took the battery out and then place it again, all works normal, it starts (vibrations feels) then nothing!, I know its turned on because I can move volume up or down and I hear the sound and vibration, if open the keyboard not any light turns on on it.
I´ll wait patient till some member can recomend more options in order to make it work again.
I´m so frustrated...
Thanks anyway for your kind help!
orb3000 said:
Well that is the problem
I live in other country so warranty is not valid here, and there is not a single place where I can take it to repair here
Very strange as one day was perfect ant the next day no screen!!
I took the battery out and then place it again, all works normal, it starts (vibrations feels) then nothing!, I know its turned on because I can move volume up or down and I hear the sound and vibration, if open the keyboard not any light turns on on it.
I´ll wait patient till some member can recomend more options in order to make it work again.
I´m so frustrated...
Thanks anyway for your kind help!
Click to expand...
Click to collapse
Dont give up, hope that I not get on ur nerves. But still I think a hard reset must be possible.
When u turn ur device of how do you do that ? When u turn it OFF with the power button you have to answer a question on the screen, u do not see the question but is the touchscreen working or how do you know where the YES/NO field is ??
So another way is take the batt out, and when u insert the batt than turn it on with one of the mentioned hardreset procedures.
There is than a question also but this is answered with the Volume UP button.
Maybe u need a second person for helping with the buttons,
The hardreset must be possible somehow, it cant be a broken touchpro
OK I tried with my phone and procedure 1.
VOL DOWN and CENTER with Phone ON
Then Push RESET with the Stylus and hold all three until:
After 5 seconds the Bootscreen showed, after that the message to press VOL UP for Restore.
You do not see the boot screen but just wait the time
You are so kind my friend!
I have tested all the hard reset options but none seems to work
Aparently I can´t do a hard reset
as every time I follow any process and wait 5 sec, then press vol up and it seems that nothing has happened, not even a soft reset!
Pressed center button and vol down, then press the rest button located behind the usb port (the one with a symbol for headphones....)
But nothing happens.
I´lll upload a small video with me doing the process, hope it helps in anyway
Here the link of the video I took with my problem
https://www.yousendit.com/download/ZW9DQ3QxeWFEbUx2Wmc9PQ
Hope this helps in any clue to solve my mysterious problem
Thanks a lot!!
Ok will wait for the video.
Inbetween another option, did u try to flash the ROM.
Can u get a rom to download from ur provider, to do so ?
After the flash the device more or less does a hardreset.
Update:
saw the video, it seems that the phone is not reacting to the center or the reset button. Because when u push reset, even if it is not in hardreset mode, it should do a soft reset right away.
But ur phone is straight reacting to the Vol keys, very strange.
Is the mentioned ROM update an option ??
What is the reaction when u hock the phone to the pc, is active sync working ?
Do you see the internal memory of the phone ?
Remove the SIM and any memory card, maybe they are causing trouble ?
Exactly, Raphael is not reacting to a hard reset and dont know why?
I´ll keep trying all methods.
Yes, I´ll try to reflash to the original AT&T ROM for Fuze tomorrow as today I am not close to a computer.
If you have any link for that mentioned ROM would be great, if not no problem I´ll find it.
Once again thanks a lot and I´ll keep looking this thread in case someone else have another recommendation
Cheers,
orb3000 said:
Exactly, Raphael is not reacting to a hard reset and dont know why?
I´ll keep trying all methods.
Yes, I´ll try to reflash to the original AT&T ROM for Fuze tomorrow as today I am not close to a computer.
If you have any link for that mentioned ROM would be great, if not no problem I´ll find it.
Once again thanks a lot and I´ll keep looking this thread in case someone else have another recommendation
Cheers,
Click to expand...
Click to collapse
Here ya go:
http://wiki.xda-developers.com/index.php?pagename=HTC_Raphael_WM6.1_ROMs
Take the one matching ur cell phone. Check the thread links for more Info.
Thanks, downloading
Tomorrow I´ll try to reflash and post results later
Cheers,
(Anyone? another idea?)
UPDTATE: I conected raphael to my computer and using pocket controller I can see that all is working ok inside but nothing on the screen, or keyboard lights.
I´ll try to hard reset now...
Hope this can help in order to solve my problem
Thanks
Attached the picture
UPDATE 2: I performed the wipe data from the device, this must be exactly as a hard reset I pressume, and nothing....
So now is there anything I can check to see if there is something loose in the connection from device to screen?
Any recommendations on how to do this?
signal from device working perfect simply does not come to screen or even to turn on light on keyboard
Any help is GREATLY apreciated!!!
What rom did you have? I had a similar problem and just had to rma it.
Hi guys,
I have a little problem where my phone's power button will not function in any way, long presses, short, almost embedding my thumb in it, all to no avail. This is doubly dissapointing as I have just installed the latest dexter plus patch to fix the problem. I still had the problem on the previous version and I thought a clean start may fix it. The only way I can get the screen on is to press the media play button! Which of course isn't doing anything on dexter.
Hunches:
I have been playing with a light sensor program and using a 3 second press to turn the phone off, I am only thinking this is related as when I re-installed then turned off the phone using a battery pull, that now the media gallery button will now not work at all, so that is a change.
Second, the power button is buggered. Seems unlikely as everthing feels normal, no big drops have occurred from heights, and the button is travelling in and out as usual.
I have also noticed that as soon as I re-insert a battery that the phone starts immediately, the M pops up as if it is already posting. So maybe it is stuck down?? Again, I don't think so, as the mechanism is working per usual.
If anyone can help it would be fantastic, you guys haven't let me down yet, and this thing is purring, but unfortunately I cannot use it lol. Just my luck.
Thanks in advance
another thing, still not solved
Another thing is happening, the phone screen turns on "after" pressing the power button, it may be once or a few times, and then pressing the gallery button.?!?!
Also, at random times it plays a podcast on my phone, the exact same podcast, and from the start, though the duration may be a few seconds then repeat, or it may go for ages, its quite a rude podcast too which has caused me to throw my phone under the car seat to shut it up when people have been trying to talk to me, as you can imagine its quite embarassing.
There are no services or apps running that I can find related to music, it may happen after pressing the camera button, or opening a website.
It is still going really fast though. And I have also reinstalled the light sensor program so I can turn it on and off without causing damage to the power button.
Thanks again everyone.
pisceanblue said:
Another thing is happening, the phone screen turns on "after" pressing the power button, it may be once or a few times, and then pressing the gallery button.?!?!
Click to expand...
Click to collapse
please clarify
sure, so the only way I can get the screen to turn back on, after turning off as per display power saving preferences, is by pressing the power button, maybe a couple of times, then following that up by pressing the gallery button next to the shutter button, pressing the gallery button doesn't seem to be working to turn the screen on now, but this combo is.
I hope that helped.
Cheers.
EDIT:::
The gallery button alone is working again. sorry guys.
You might just want to reflash it to stock to see if this resolves the problem.
Yeah I think I may have to.
Before I do., I was reading a post on a different forum where another person was having a similar issue. They seemed to solve the problem by using rom manager to boot to a manual restore menu where there was a button tester section, after using it the power button worked for them. I tried but after resetting it displayed a triangle graphic then rebooted.
Is there any way to do this with our open recovery program or any other utility to test the functionality or maybe reset the button or apply a patch etc.
Thanks again :-D
Sent from my XT720 using XDA App
Getting Frustrating
Alright so I followed your advice on your videos on how to reflash to stock, so of course my bootloader does not show up the same as yours on the video. I can get to the bootloader fine, using the button combo or by using quick boot > bootloader, both have the exact same result, the boot loader screens as follows:
Bootloader Fastboot mode
80.89
and that is it....
Also, my computer using rsdlite does not acknowledge the phone, not omap drivers loading etc. Followed your instructions exactly.
This is frustrating me to no end lol.
I am guessing that because I can get to the bootloader with combo no problem, that the buttons physical connections are working.. At least thats a positive.
Can I flash to stock with openrecovery? Or maybe to an earlier version of Dexters froyo? Other ideas?
Any help would be much appreciated guys, trying to use this phone at work with light sensors to turn off screen is not as easy as they say. OMG....
Thanks so much
pisceanblue said:
Bootloader Fastboot mode
80.89
Click to expand...
Click to collapse
The fastboot bootloader isn't the right one. So... if you hold volume up + camera shutter while powering on you end up in fastboot? That's really weird.
Maybe your keys have been remapped somehow? Does anyone know a chord to boot fastboot? Perhaps check to see if your USB port is clean?
Lmao
Just my luck to have a weird problem. I thought it may have been remapped so I have been trying the program buttonremap. It doesn't seem to let me do anything except stop the buttons I re assign doing anything :'(
Does anyone have a proper key mapping file that I can replace with my faulty one to hopefully fix it?
Or any other ideas?
Cheers everyone
Sent from my XT720 using XDA App
Just checked my system / user / keylayout folder. How many files are supposed to be inside, there are a few. I checked the contents of some and they seemed to be the same. Just an idea.... thanks again.
Sent from my XT720 using XDA App
Ok installed anyunlock it allows you to use any physical button to unlock the screen. It doesn't respond when the Power button is pressed, it responded fine to volume rockers, gallery and shutter though.
Anyone know if this would mean for sure its a physical problem before I crack it open and try and fix it.
Thanks guys.
Sent from my XT720 using XDA App
No one has any solutions for me? Come on guys.
Sent from my XT720 using XDA App
Breakthrough!
I am pretty sure I have fixed the problem, I tapped the phone fairly hard on its sides and back, and lo and behold after a battery pull and replacement it didn't turn itself on, I waited, nothing, so then I held the power button and it started up!!!!
But....I have another problem that happened before that, I am stuck in the boot animation that open recovery uses before going into its program (i.e. where you can load nandroid, wipe dalvik cache etc).
I was about to load a new rom, and was in open recovery, had installed it and about to do the reset and the phone turned itself off, and thats when I got the problem with the sticking boot animation.
So just to be clear, I am stuck in a boot loop, but not with the M logo, the restore logo.
I hope the power button solution can help someone else, as random as it is.
If anyone could help me get out of this boot loop without flashing stock that would be great. ( i can get to the real bootloader now btw)
Thanks again everyone.
Solved it all
Just took the sd card out and rebooted. And the power is getting better after banging it.
Thanks to all.
Sent from my XT720 using XDA App
pisceanblue said:
Solved it all
Just took the sd card out and rebooted. And the power is getting better after banging it.
Thanks to all.
Click to expand...
Click to collapse
So, is your conclusion is that the button was stuck and the banging freed it? It doesn't restick?
The Button is not perfect still. Sometimes over sensitive Occasionally it will not even work but it works most of the time. I am just wondering what cleaning solution I could use to free it some more.
It has certainly been a trying problem. Cheers for the help.
Now I need to figure out why I have this strange ghosting on the top of my screen.....
Sent from my XT720 using XDA App
Samsung Galaxy S2 Power Button Not Working
Hi Guys,
Any solution for the power button problem? Current latest Android 2.3.3 Samsung Galaxy S2 also having the same power button problem. Most of the time I can't use my power button to turn on/off the screen (wake/sleep) and there's no menu for long tap as well. Luckily it does wake when i press the only physical Samsung center button.
What i have already tried: Factory Reset, disable Power Saving Mode, Spare Part+ (apps), Screen Off and Lock (apps), and all won't help.
Is there any current updates or patches to allow the power button to work as usual?
Thank you.
take it to the samsung technical centre
Thats if you still have warranty
archer88 said:
take it to the samsung technical centre
Click to expand...
Click to collapse
won't help because this is the 3rd phone replacement from the shop with the same problem. 100% Android software problem.
Hey guys. I'm pretty desperate so i decided to make this thread.
Here is my problem:
I have changed screen on my phone today. Everything went without any problems since I tried to turn on the phone.
When I tried to turn it on I can see only MI logo on display ... Then after couple of seconds phone will restart automatically and goes into Recovery mode.
I tried to boot it from there without any results. Also tried to reset and wipe data without any results.
The biggest problem is that I cant even get into Fastboot menu by pressing Power button + volume down button. So I cant connect my phone with PC and try to flash new ROM.
Any suggestions? I would be really thankful for any advice.
Thank you very much.
roweruur said:
Hey guys. I'm pretty desperate so i decided to make this thread.
Here is my problem:
I have changed screen on my phone today. Everything went without any problems since I tried to turn on the phone.
When I tried to turn it on I can see only MI logo on display ... Then after couple of seconds phone will restart automatically and goes into Recovery mode.
I tried to boot it from there without any results. Also tried to reset and wipe data without any results.
The biggest problem is that I cant even get into Fastboot menu by pressing Power button + volume down button. So I cant connect my phone with PC and try to flash new ROM.
Any suggestions? I would be really thankful for any advice.
Thank you very much.
Click to expand...
Click to collapse
Did you follow a tutorial for replacing the screen on your device? Where did you get the screen from? Was your screen replacement just the Touch Panel or the full screen replacement with LCD + Touch Panel? Was it an actual Xiaomi part or an aftermarket part? I would take your device apart again and make sure you didn't leave something loose or disconnected.
Quick question. Was you old display still working where you could see what was going on? Like, was it just cracked or was it completely inoperable?
Sent from my Nexus 6 using XDA-Developers mobile app
Thanks for reply. Yes I followed complete tutorial on youtube. Screen is from ebay. It should be original. I replaced full screen ( lcd + touch panel ).
So found simillar problem as mine - due to improper installation of back cover volume up button was pressed which caused that phone went to recovery menu after start ... ( you have to hold volume up + power key to get to Recovery menu). So I tried to dismantle it again but it didnt help. Still have same problem.
Yes old display is alright. I can see everything just touch screen is broken so I cant do anything on it. But I cant imagine this would be problem of display ....
Give your craftsmanship and handiwork the benefit of the doubt and install your old LCD+Touch Panel and see what happens. If you have everything installed correctly with every cable connected to it proper location then you should be able to boot normally.
Sent from my Nexus 6 using XDA-Developers mobile app