helo all,
I am using xoom wifi stock 3.2 . I am not rooted. I have an USB otg cable but when I plug any USB mass storage eg 4/8 gb my xoom don't show any device. What should I do now?
raihankabir_1 said:
helo all,
I am using xoom wifi stock 3.2 . I am not rooted. I have an USB otg cable but when I plug any USB mass storage eg 4/8 gb my xoom don't show any device. What should I do now?
Click to expand...
Click to collapse
I believe that you must be rooted to use the Xoom in USB host mode. I've been rooted from a couple of days after I bought my Xoom, so I don't remember.
You do have external sd card (read only) right?
Make sure that 'USB Debugging' is disabled.
i'm afraid you need custom rom for this.
okantomi said:
I believe that you must be rooted to use the Xoom in USB host mode. I've been rooted from a couple of days after I bought my Xoom, so I don't remember.
You do have external sd card (read only) right?
Click to expand...
Click to collapse
I have 32 gb SD card that xoom can mount but it can't joint USB drives
raihankabir_1 said:
I have 32 gb SD card that xoom can mount but it can't joint USB drives
Click to expand...
Click to collapse
Then as I thought, you need to be rooted and install a custom kernel or rom (Tachi kernel or Hammerhead rom for HC3.2) that says it enables usb OTG host mode in the releas notes. Then you can use your OTG cable (and the free app USB Mass Storage Watcher OTG) to mount and use thumb drives and newer HHDs (that don't require much power to run).
okantomi said:
Then as I thought, you need to be rooted and install a custom kernel or rom (Tachi kernel or Hammerhead rom for HC3.2) that says it enables usb OTG host mode in the releas notes. Then you can use your OTG cable (and the free app USB Mass Storage Watcher OTG) to mount and use thumb drives and newer HHDs (that don't require much power to run).
Click to expand...
Click to collapse
Thanks for the reply. Where can I get the steps for rooting? Is it possible to go back to custom rom after rooting?
raihankabir_1 said:
Thanks for the reply. Where can I get the steps for rooting? Is it possible to go back to custom rom after rooting?
Click to expand...
Click to collapse
Yes you can flash a custom rom.
For the correct rooting guide for your Xoom model (3G or WiFi-only, country of origin) check out the Xoom Heaven thread in General section 1st, to see if your Xoom model is addressed there.
Related
Hello all,
I am not sure if i connect a 500 gb usb external hard disk to my xoom through micro usb otg cable. Can anyone answer this? IF positive, I will buy a 500 gb instantly.
That depends.
I am running Tiamat manta ray 2.0.1 on UK MZ601 3g xoom and I can mount an external WD usb powered 500Gb drive over otg with no problems.For stock 3.01which I came from it didn't work.
I use usb otg watcher (available in market place) to mount and es filemanager to move, and copy and browse etc
Regards,
wendell7 said:
That depends.
I am running Tiamat manta ray 2.0.1 on UK MZ601 3g xoom and I can mount an external WD usb powered 500Gb drive over otg with no problems.For stock 3.01which I came from it didn't work.
I use usb otg watcher (available in market place) to mount and es filemanager to move, and copy and browse etc
Regards,
Click to expand...
Click to collapse
I have a new WD Passport Essential 750GB HDD that works fine with the Moto OTG adaptor and the USB Mass storage Watcher OTG app. My Xoom's configuration is in my sig.
okantomi said:
I have a new WD Passport Essential 750GB HDD that works fine with the Moto OTG adaptor and the USB Mass storage Watcher OTG app. My Xoom's configuration is in my sig.
Click to expand...
Click to collapse
If i use stock 3.2 rom would it be possible then to use?
raihankabir_1 said:
If i use stock 3.2 rom would it be possible then to use?
Click to expand...
Click to collapse
You could try but that app I mentioned requires root and I'm not sure if stock 3.2 provides usb host mode support.
I'm still on Tiamat 1.0 and can read my WD 1TB HDD (NTFS) without issue.
I'm still in stock 3.0.1 uk and I can use my 500, 750 and 1T WD passports fine by mounting through terminal emulator.
Sent from my HTC Desire using Tapatalk
Hi to all!
Here's the problem that I have.
After upgrading my Xoom (US 3G) to Tiamat 2.1 Hammerhead USBOTG stopped to work. When I try to connect flashdrive via this cable it blinks only once and that's all. The folder USBOtg is empty -> nothing is shown (but I know that there are files). I tried to format flashdrive to various filesystems (NTFS, FAT32) -> no result.
Another strange thing after upgrade is with MicroSD folder. It shows me only old data. All new one that I copied to it via PC it doesn't show at all. AND!!! PC doesn't see the content of folder with name "external" on Xoom but when I copy there files from PC then Xoom can see them.
May anyone advice any steps to return usbotg and microsd in normal working state?
I tried to re-flash Xoom with previous various versions of firmwares (mods) -> the same situation.
BR, akadimka
akadimka said:
Hi to all!
Here's the problem that I have.
After upgrading my Xoom (US 3G) to Tiamat 2.1 Hammerhead USBOTG stopped to work. When I try to connect flashdrive via this cable it blinks only once and that's all. The folder USBOtg is empty -> nothing is shown (but I know that there are files). I tried to format flashdrive to various filesystems (NTFS, FAT32) -> no result.
Another strange thing after upgrade is with MicroSD folder. It shows me only old data. All new one that I copied to it via PC it doesn't show at all. AND!!! PC doesn't see the content of folder with name "external" on Xoom but when I copy there files from PC then Xoom can see them.
May anyone advice any steps to return usbotg and microsd in normal working state?
I tried to re-flash Xoom with previous various versions of firmwares (mods) -> the same situation.
BR, akadimka
Click to expand...
Click to collapse
Two different issues--if you read the release notes with the Hammerhead Rom, Team Tiamat removed the USB Mass Storage enabling that had been in earlier Rom, due to various difficulties. So that means you can no longer use your PC to copy files into the micro sd card in the Xoom, but you can cop files directly to the sdcard using an adapter or card reader. Your Xoom should still have access to the files on your micro sd card at mnt/external1.
The usbOTG works fine for me but it needs the help of an app like USB Mass Storage Watcher OTG or Drive Mount. Both will work. It also helps to reboot with the drive plugged in the first time if you are having a hard time getting the Xoom to recognize it.
Thanx! Drive Mount helped me with recognizing and mounting flash drive (but only after Xoom reboot with drive plugged in). USB Storage Watcher OTG crashes everytime when I start it with drive connected -> with disconnected it starts normally but won't see any after-connected drives. Ssems that I'll use Drive Mount program
As for MicroSD -> even connected directly to PC and copied some files to it Xoom still sees only old data. Any ideas?
BR, Dmitry
Sent from my Xoom using XDA Premium App
akadimka said:
Thanx! Drive Mount helped me with recognizing and mounting flash drive (but only after Xoom reboot with drive plugged in). USB Storage Watcher OTG crashes everytime when I start it with drive connected -> with disconnected it starts normally but won't see any after-connected drives. Ssems that I'll use Drive Mount program
As for MicroSD -> even connected directly to PC and copied some files to it Xoom still sees only old data. Any ideas?
BR, Dmitry
Sent from my Xoom using XDA Premium App
Click to expand...
Click to collapse
Actually, try checking the folder mnt/external1 (1) as this is HC3.2's official mount point. The Microsd mount point is an artifact of an older Rom.
i am using hammerhead rom with tachi kernel.
yup the usb otg not working.
tried both usb watcher and drive mount.
rohit3192 said:
i am using hammerhead rom with tachi kernel.
yup the usb otg not working.
tried both usb watcher and drive mount.
Click to expand...
Click to collapse
Make sure that you are using a REAL usbOTG cable.
A real USB otg cable? What needs to be special about the cable in order for it to work?
Sent from my Nexus One using xda premium
msavic6 said:
A real USB otg cable? What needs to be special about the cable in order for it to work?
Sent from my Nexus One using xda premium
Click to expand...
Click to collapse
This is where I will suggest that you do some research. Start with this forum and then search elsewhere. Just today I have answered this question 3 times. Search on my name and you will see my posts with your answer.
i am using micro usb male to normal usb female.
cable is gold plated and branded.
but others have also mentioned that usbotg not working after they updated to 3.2
though i never tested on 3.1
rohit3192 said:
i am using micro usb male to normal usb female.
cable is gold plated and branded.
but others have also mentioned that usbotg not working after they updated to 3.2
though i never tested on 3.1
Click to expand...
Click to collapse
Your cable will never work because it is not OTG. OTG has a different pin configuration to allow the Xoom to function in usb host mode. If you are handy with a soldering iron you could make one, but why not buy one, they are availble. Here is my Google search for USBOTG Xoom to get you started: http://www.google.com/search?hl=en&source=hp&q=usb+otg+xoom&aq=2s&aqi=g1g-s9&aql=&oq=usbOTG
Can u plug a full size USB stick into the xoom at all?
Sent from my DEFY running CM7 using XDA App
u need the host cable- by the Motorola one it will work, alot of the cheap ones won't.
http://www.ebay.com/itm/260879217802?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
that one works, i have several. The same guy sells an led-less version for $4 that works too.
how does it work? Does it show up as a new folder in the file manager?
slonn said:
how does it work? Does it show up as a new folder in the file manager?
Click to expand...
Click to collapse
You will probably need an app like USB MassStorage Watcher or Drive Mount (both free) to mount/unmount the drive. It will show up on the same directory level as sdcard (internal storage) and external1. It will be at usbOTG.
okantomi said:
You will probably need an app like USB MassStorage Watcher or Drive Mount (both free) to mount/unmount the drive. It will show up on the same directory level as sdcard (internal storage) and external1. It will be at usbOTG.
Click to expand...
Click to collapse
Thanks for the tip! I got the Drive Mount app and it did the trick. Was starting to worry that the cable I got on eBay was a fake.
Cool! Thx 4 all the posts...
Sent from my DEFY running CM7 using XDA App
okantomi said:
You will probably need an app like USB MassStorage Watcher or Drive Mount (both free) to mount/unmount the drive. It will show up on the same directory level as sdcard (internal storage) and external1. It will be at usbOTG.
Click to expand...
Click to collapse
i m in same boat. I have XOOM wifi USA version. It is NOT ROOTED.
does it work to read USB drive without rooting?
current OS version on my XOOM is 3.2.1 (HTK75D)
No, you must be rooted and running a custom kernel or Rom that support usb host mode.
okantomi said:
No, you must be rooted and running a custom kernel or Rom that support usb host mode.
Click to expand...
Click to collapse
Thanks for reply. I m totally new to rooting etc.
well is android 4.0 is going to release for this XOOM model soon? and does it resolve this issue?
I'm betting that our developers are making us an ICS Rom with usb host mode support...
will this also work with a usb gender like http://www.amazon.com/USB-Gender-Changer-Female/dp/B000BSN4UY/ref=pd_sim_e_2 in stead of a usb otg?
I have installed android 4.0 on my motorola xoom wifi usa version.
it is NOT ROOTED.
Can i read usb drive ( pen drive or external hard disk ) with this Or still rooting is needed?
I have following adapter.
http://www.amazon.com/Micro-USB-Mal...3?s=electronics&ie=UTF8&qid=1327371621&sr=1-3
is only rooted is Ok or it need to install other custom OS version?
it will be great somebody can reply ASAP.
So there is no other app that doesn't require root? I just want to hold on rooting the device..is USB OTG supported with 4.0?
I got a USB OTG cable but when i plug it in nothing happens. it looks all confusing, I am running build 17 of Team EOS ICS. What do i do?
Try downloading/running one of the apps that mount external USB drives.
slonn said:
Try downloading/running one of the apps that mount external USB drives.
Click to expand...
Click to collapse
I have tried about 3 of them but nothing happens.
Is there a certain format it needs to be ? (Fat32) etc.
Do i need a special kernel?
Which cable did you buy? I'm about to buy an OTG cable as well.
http://www.ebay.com.au/itm/260924502107?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
----DELETED----
hi there, i'm new user for MZ601 3G a few day still bussy about how to connect my usb storage to my mz601 with eos rom ics 4.0.4, i'm afraid is only me that failed to connect my usb storage to my xoom with ics from eos, cause everyone says they can connect usb storage to xoom
all thing i have done install usb storage watcher otg, install total commander until re-flash eos rom 2.0.0 or 77 build still my xoom cannot detect my usb storage already try with 3 different type of otg cable, looking under media/usb still empty folder and with usb storage watcher is say : No USB Connection..
Can someone help me with this, cause if usb storage can run normaly it will help me much for my dailly activities
Cheers