Related
Can someone point me to where I can learn how to use set cpu and set voltage properly. Just installed superotimized kernel and wondering how to take full advantage of it
p4ranoid4ndroid said:
Can someone point me to where I can learn how to use set cpu and set voltage properly. Just installed superotimized kernel and wondering how to take full advantage of it
Click to expand...
Click to collapse
overclocking is pre-enabled, under volting can be done through an app the link is in the thread. there are 2 settings. try about -50v each if that works fine bump one down to -75mv at a time. test the phone over a day or two and see how it runs, see if it has sleep death after a few periods of inactivity, especially extended periods, see if it has sleep death while charging, which seems to make a difference that will test the low setting.
see if the phone shuts down without freezing, and see if it shuts down without freezing while charging, the heat in the battery makes a big difference, play some 3d games. if you have freezing issues you can disable overclocking under different situation with set cpu or se t the volts to a more conservative setting.
Dani897 said:
overclocking is pre-enabled, under volting can be done through an app the link is in the thread. there are 2 settings. try about -50v each if that works fine bump one down to -75mv at a time. test the phone over a day or two and see how it runs, see if it has sleep death after a few periods of inactivity, especially extended periods, see if it has sleep death while charging, which seems to make a difference that will test the low setting.
see if the phone shuts down without freezing, and see if it shuts down without freezing while charging, the heat in the battery makes a big difference, play some 3d games. if you have freezing issues you can disable overclocking under different situation with set cpu or se t the volts to a more conservative setting.
Click to expand...
Click to collapse
I've been told that undervolting can improve the battery time. Of course, lots of varying opinions of how good/bad it may be to overclock.
If I want to just undervolt, is that possible with SetCPU?
Dani897 said:
overclocking is pre-enabled, under volting can be done through an app the link is in the thread. there are 2 settings. try about -50v each if that works fine bump one down to -75mv at a time. test the phone over a day or two and see how it runs, see if it has sleep death after a few periods of inactivity, especially extended periods, see if it has sleep death while charging, which seems to make a difference that will test the low setting.
see if the phone shuts down without freezing, and see if it shuts down without freezing while charging, the heat in the battery makes a big difference, play some 3d games. if you have freezing issues you can disable overclocking under different situation with set cpu or se t the volts to a more conservative setting.
Click to expand...
Click to collapse
ewingr said:
I've been told that undervolting can improve the battery time. Of course, lots of varying opinions of how good/bad it may be to overclock.
If I want to just undervolt, is that possible with SetCPU?
Click to expand...
Click to collapse
Interesting stuff...
I too would like to know if it is possible to simply under-volt. Does anyone know the optimal settings for SetCpu with the Captivate...or does it vary depending on each users profile/ phones?
So Ive been playing around with various settings for set cpu and voltage control and all has been well so far. The only problem im having is voltage control seems broke. I try to open the all but it just black screens. I tried to clear the memory and unistall and reinstall and still have the same problem. Any ideas?
http://forum.xda-developers.com/attachment.php?attachmentid=432086&d=1288709102
^you can under volt setirons kernel and disable overclocking with this app.
i find my battery life to be less than stock with this kernel, i need to see if it is a common issue, maybe because it is not a captivate kernel. but in the past with unhelpfuls kernel for 2.1 battery life was awesome.
spartan062984 said:
Interesting stuff...
I too would like to know if it is possible to simply under-volt. Does anyone know the optimal settings for SetCpu with the Captivate...or does it vary depending on each users profile/ phones?
Click to expand...
Click to collapse
It's going to depend on the individual CPU in your phone. Your best result is to start at a given clock speed and begin lowering voltage in the smallest step possible, test for stability, repeat until you begin to notice instability (or you just run out of voltage options). You can just undervolt without increasing clock speed any, or you can not undervolt yet raise clock speed, or you can overclock and undervolt, depending on how your particular chip reacts. Some might need additional voltage to stabilize the snapdragon at 1.2Ghz while others (mine for example) is stable Able @ -100mV and 1.2Ghz. Overclocking silicon is the ultimate in YMMV.
Another thing to bear in mind is that increasing clock speed necessarily increases power consumption. There is no way around this. So a chip at 1.2Ghz will use more juice than 1Ghz even with the same voltage. It's difficult to say at this point whether, say, the Snapdragon @ 1.2Ghz and -100mV uses more or less power than the same chip @1Ghz and stock voltage. It's absolutely possible that the former uses more power, which would explain why you see at least one claim here of battery life decreasing even when voltage settings are left untouched.
hawkeyefan said:
It's going to depend on the individual CPU in your phone. Your best result is to start at a given clock speed and begin lowering voltage in the smallest step possible, test for stability, repeat until you begin to notice instability (or you just run out of voltage options). You can just undervolt without increasing clock speed any, or you can not undervolt yet raise clock speed, or you can overclock and undervolt, depending on how your particular chip reacts. Some might need additional voltage to stabilize the snapdragon at 1.2Ghz while others (mine for example) is stable Able @ -100mV and 1.2Ghz. Overclocking silicon is the ultimate in YMMV.
Another thing to bear in mind is that increasing clock speed necessarily increases power consumption. There is no way around this. So a chip at 1.2Ghz will use more juice than 1Ghz even with the same voltage. It's difficult to say at this point whether, say, the Snapdragon @ 1.2Ghz and -100mV uses more or less power than the same chip @1Ghz and stock voltage. It's absolutely possible that the former uses more power, which would explain why you see at least one claim here of battery life decreasing even when voltage settings are left untouched.
Click to expand...
Click to collapse
Thanks for clarifying Hawkeye! I will report back on in a few days once i have tested out a few profiles. In my opinion, I feel that it is best to leave Over-clocking at default and maximize battery utilization with setcpu. However, the thought of over-clocking the Dragon beast is VERY tempting. Who wouldn't? I will definitely check out the differences when playing games and such.
spartan062984 said:
Thanks for clarifying Hawkeye! I will report back on in a few days once i have tested out a few profiles. In my opinion, I feel that it is best to leave Over-clocking at default and maximize battery utilization with setcpu. However, the thought of over-clocking the Dragon beast is VERY tempting. Who wouldn't? I will definitely check out the differences when playing games and such.
Click to expand...
Click to collapse
I have to tell you, I'm not personally very fond of SetCPU on this device, even though I paid for the app (ugh). With raspdeep's voltage control app and SetIron's OC/UV kernel, the CPU defaults to 1.2Ghz at stock voltage, which for a basic setup is fine. Voltage Control app is phenomenal for adjusting in increments of 25mv at a time...one setting is for high clocks (1Ghz - 1.2Ghz) and the other is for < 1Ghz. It's probably best actually to start with the lower clock setting in Voltage Control, as your phone will spend the lion's share of it's time at those clocks and so that is where you should see the most gain in battery life. My only gripe is that I can't get the boot settings to stick on the Captivate so I have to go in and adjust them each time I reboot the phone. no biggie there.
SetCPU, on the other hand, has caused me loads of problems in the past, including causing the phone not to wake up from sleep and just atrocious battery life, I assume from constantly polling the CPU clock to measure clock speed. I have not experienced any of that with Overclock Widget, but I also don't use any of the independent clockspeed controls in the app...basically it's just a widget to display clock speed the way I use it. Otherwise, Setiron's kernel gives the 200mhz overclock and I just let the Hummingbird deal with changing clocks on its own. Jmo, but it works for me with no resulting battery drain beyond the additional I expect as a result of the extra 200mhz.
edit: whoops, long day. hummingbird in my post from above, not snapdragon. I need a drinky poo.
hawkeyefan said:
I have to tell you, I'm not personally very fond of SetCPU on this device, even though I paid for the app (ugh). With raspdeep's voltage control app and SetIron's OC/UV kernel, the CPU defaults to 1.2Ghz at stock voltage, which for a basic setup is fine. Voltage Control app is phenomenal for adjusting in increments of 25mv at a time...one setting is for high clocks (1Ghz - 1.2Ghz) and the other is for < 1Ghz. It's probably best actually to start with the lower clock setting in Voltage Control, as your phone will spend the lion's share of it's time at those clocks and so that is where you should see the most gain in battery life. My only gripe is that I can't get the boot settings to stick on the Captivate so I have to go in and adjust them each time I reboot the phone. no biggie there.
SetCPU, on the other hand, has caused me loads of problems in the past, including causing the phone not to wake up from sleep and just atrocious battery life, I assume from constantly polling the CPU clock to measure clock speed. I have not experienced any of that with Overclock Widget, but I also don't use any of the independent clockspeed controls in the app...basically it's just a widget to display clock speed the way I use it. Otherwise, Setiron's kernel gives the 200mhz overclock and I just let the Hummingbird deal with changing clocks on its own. Jmo, but it works for me with no resulting battery drain beyond the additional I expect as a result of the extra 200mhz.
edit: whoops, long day. hummingbird in my post from above, not snapdragon. I need a drinky poo.
Click to expand...
Click to collapse
LOL. No Worries. I myself made the same mistake. I thought something was odd with my post. SnapDragon...Hummingbird....Bulbasaur.....I knew what you meant. lol
Still not having any luck with the voltage control app. Ive tried flashing different roms to see if it would work. I undervolted it to 100/75 the first time i did it and now i cant change. Only a little worried
i guess there was an issue with the set on boot scripts not working. supposedly that is fixed, i dont know for sure though, i haven't updated.
From what I'm gathering, in order to undervolt, you must have a kernel to su pport that, for example Setirons.
I'm not necessarily interested in overclocking, as it performs well as is. Of course there are arguments that overclocking may ultimately harm the phone, and arguments that by the time that happens, you'd be ready for a new phone. In any event, if I start getting slower, I may interest in overclocking.
Does anyone know if dramatic improvement in battery performance with underclocking?
I've noticed quite a bit of a difference, just pretty difficult to tune it precisely. (Coming from a person who enjoys overclocking computers a little too much). I just wish there was an app that would test each frequency and then let you know which one failed (without having to manually set it).
Does anyone else think the CPU running at 480Mhz-800Mhz screen on is a bit too high? It's more than capable running at a 122Mhz minimum - heck, even 19Mhz, although it doesn't spend much time at 19Mhz. Also, if perflock is enabled, it locks itself to 245Mhz only when screen off - still seems a bit too high for me, considering there's lower selectable frequencies.
Anyone who's temprooted their device: Are you using SetCPU to change the CPU frequencies/disabling perflock? I have my Chacha running at 800Mhz max / 122Mhz min perfectly fine (running my battery down for a while to see if the battery life benefits) - although occasionally, it still locks itself to 122Mhz even after turning the screen on for about a minute, which I believe is a kernel issue
For reference, the frequency options are: 19Mhz, 122Mhz, 128Mhz, 245Mhz, 480Mhz and 800Mhz.
128Mhz doesn't actually work, and if it's selected, it uses 245Mhz instead even though SetCPU says "128 min"
Unfortunately I can't help you, but I'm totally interested on the subject!
As far as I know and tested on other android devices, setting the CPU freq too low will cause some unwanted behavior like being unable to power up the screen. Happened on a Galaxy S, where I've set the freq to 19Mhz (or something similar) and I've locked the screen. Pressing the power button did nothing so I had to re-flash the rom.
really need low cpu frequency?
low frequency is certainly not good. For chachar, I just hope 600 frequency could be done the hardware itself(not by setcpu). I hate the power consumption is too big, and the machine is easy to get hot.
Alex C. said:
As far as I know and tested on other android devices, setting the CPU freq too low will cause some unwanted behavior like being unable to power up the screen. Happened on a Galaxy S, where I've set the freq to 19Mhz (or something similar) and I've locked the screen. Pressing the power button did nothing so I had to re-flash the rom.
Click to expand...
Click to collapse
True, setting the frequency too low is bad for some devices, but in my personal experience with my Chacha, I can actually run mine at 19Mhz min/800Mhz max and have little to no problems, since it doesn't spend much time at 19Mhz anyways. (I use no SetCPU profiles, as I feel they have little to no benefit on battery life.)
All of this is just a thought though, since HTC set the minimum to 480Mhz with the screen on which seems way too high to me :/
Also, locking the CPU to a single low frequency was actually a bad thing on one of my old devices, a Desire Z, which usually caused wake problems, etc.
semanty said:
low frequency is certainly not good. For chachar, I just hope 600 frequency could be done the hardware itself(not by setcpu). I hate the power consumption is too big, and the machine is easy to get hot.
Click to expand...
Click to collapse
600Mhz is possible indeed - the MSM7227 processor that the Chacha uses is actually rated at 600Mhz, but HTC factory overclocked it to 800Mhz. It would require a custom kernel to have 600Mhz added back in
anyone thought of a way to undervolt???? i mean use less voltage for each frequency..am trying to search for kernels to flash but cudnt find any
This is a question I've never seen asked, but it's an important one. What are you phones CPU Freqs? What Govs do they have, and what Profiles do you use?
Rom: PyroIce
Main: 192 Min, 918 Max. OnDemand.
Screen Off: 192 Min, 384 Max. PowerSave.
InCall: 192 Min, 540 Max. Interactive.
Time 11pm-7am: 192Min/Max Powersave.
Sent from my HTC myTouch_4G_Slide using Tapatalk
that's cool, i might start using profiles again. from fiddling around i've noticed the difference between the ondemand and conservative governors- with ondemand, the processor seems to go from min. to all the way to max. and back down to min, and doesn't use the middle frequencies as much, while on conservative, the processor doesn't shoot up to max. as easily and seems to meander thru the middle frequencies a lot more. it makes sense too, because i've noticed that the phone seems snappier with ondemand.
i noticed you're using some of the others... i'll have to check them out as well.
ondemand
Available in most kernels, and the default governor in most kernels. When the CPU load reaches a certain point (see "up threshold" in Advanced Settings), ondemand will rapidly scale the CPU up to meet demand, then gradually scale the CPU down when it isn't needed. - SetCPU website
conservative
Available in some kernels. It is similar to the ondemand governor, but will scale the CPU up more gradually to better fit demand. Conservative provides a less responsive experience than ondemand, but can save battery. - SetCPU website
performance
Available in most kernels. It will keep the CPU running at the "max" set value at all times. This is a bit more efficient than simply setting "max" and "min" to the same value and using ondemand because the system will not waste resources scanning for the CPU load. This governor is recommended for stable benchmarking. - SetCPU website
powersave
Available in some kernels. It will keep the CPU running at the "min" set value at all times. - SetCPU website
userspace
A method for controlling the CPU speed that isn't currently used by SetCPU. For best results, do not use the userspace governor. - SetCPU website
Interactive
The 'interactive' governor has a different approach. Instead of sampling the cpu
at a specified rate, the governor will scale the cpu frequency up when coming
out of idle. When the cpu comes out of idle, a timer is configured to fire
within 1-2 ticks. If the cpu is 100% busy from exiting idle to when the timer
fires then we assume the cpu is underpowered and ramp to MAX speed.
If the cpu was not 100% busy, then the governor evaluates the cpu load over the
last 'min_sample_rate' (default 50000 uS) to determine the cpu speed to ramp down
to
so, I bought set cpu about 3 phones ago, but I never really saw a differnence, can it be used with the stock kernel?
yellowjacket1981 said:
so, I bought set cpu about 3 phones ago, but I never really saw a differnence, can it be used with the stock kernel?
Click to expand...
Click to collapse
Yeah Plus there's a huge difference with the Battery. I you use my CPU Settings, you should gain 3 hours Min on your phone. Also dropping the CPU in call is great, helps for longer calls and less overheating. If your S-Off you should use a custom kernel. UV Kernels are great.
AgentCherryColla said:
Yeah Plus there's a huge difference with the Battery. I you use my CPU Settings, you should gain 3 hours Min on your phone. Also dropping the CPU in call is great, helps for longer calls and less overheating. If your S-Off you should use a custom kernel. UV Kernels are great.
Click to expand...
Click to collapse
I actually just got an uv kernel, I am about to flash it, I will use your settings too, thanks.
yellowjacket1981 said:
I actually just got an uv kernel, I am about to flash it, I will use your settings too, thanks.
Click to expand...
Click to collapse
If you run a Sense 3.6 Rom, boost the CPU to 1Ghz. 918Mhz Lags.
Sent from my HTC myTouch_4G_Slide using Tapatalk
yellowjacket1981 said:
so, I bought set cpu about 3 phones ago, but I never really saw a differnence, can it be used with the stock kernel?
Click to expand...
Click to collapse
Yes.
You cannot use anything the kernel doesn't already serve as an option, though.
SetCPU doesn't create options - it allows you user-level access to the ones already existing.
Normally you have no control over your clock speed but with it you can...say... limit the maximum clock speed to only be two-thirds of the stock speed.
Since it doesn't ramp up all the way, it doesn't drain as much power.
If you are playing games and stuff that needs a lot of resources, then the slower clock speeds cost you battery since it takes more effort to get the same work done. But if you don't do much with your phone, and don't need a lot of high-end CPU ability, why let it run flat out?
You can also set it to be like that only sometimes, and maximize battery savings by telling your device to chill out when it doesn't have to be awesome.
Now, if you get into custom kernels where you or a dev has opened up more options, SetCPU will again give you user level control over them.
Especially once you get into overclocking beyond manufacturer(s) recommendations, not having some end-user level control over the processor like this is irresponsible.
If you think I run a 1.7 or 1.9 or 1.5+anything on the device flat-out balls-to-the-wall all the time, I would ask you if you drive your car with the gas pedal smashed to the floor all the time. (it's a fitting analogy)
No, again, that would be irresponsible abuse of the hardware for no good reason.
If not SetCPU, then there would be something else to use, but SetCPU is a great interface that not only works well but is maintaned within the XDA community by a member here.
I will always go for the XDA community member version of any app first - it's usually a problem solved from a perspective very near the way I am perceiving the issue, supports the community, and is always easier to find help on if necessary.
What's even cooler is SetCPU is given away free by the dev to XDA members.
I did go ahead and buy it anyway to support the dev. It is a fantastic tool at my disposal, and I have come to realize just how much time and energy goes into making this kind of stuff.
Beyond all that, though, there are a ton of crap apps and software out there slapped together by people who don't care or didn't put the right level of effort into their work. When I find something that actually works and works well after sifting through a sea of garbage, if there is a paid version of the app i'll usually buy it not only as a thank you but also to encourage that particular person to keep working. They - unlike many, many others (in my opinion) earned it.
I know i'm drifting off topic a bit, sorry for that - I just really appreciate quality work and SetCPU falls in with that crowd nicely.
Even without a custom kernel providing options beyond stock, there is still a lot of value this app can hold for anyone with root level access to their device.
Blue6IX said:
If you are playing games and stuff that needs a lot of resources, then the slower clock speeds cost you battery since it takes more effort to get the same work done.
Click to expand...
Click to collapse
Is this true? in my mind, I feel like it will take longer/not be as smooth, but wouldn't necessarily be worse for battery than a higher clock speed.
On a one-for-one comparison it leans more towards an even playing field, until you add that it's a dual-core processor and it very heavily skews the results towards less battery at higher clock speeds for complex operations.
Faster CPU speeds process the actions more quickly, and when you have to crunch a lot of numbers real quick like you do for most games the higher clock speed (especially on the dual core we are using) will complete the act with less power used. It is able to keep up with and/or outpace the flow of data being thrown at it.
If you are just using a notepad or browsing some forums maybe...sending a few texts? Then the higher clock speeds show a negative return on battery usage - you don't need it and it's wasteful.
But when the data has to stay buffered because the CPU is taking it's time working with it, not only is there more electricity consumed by keeping the processor alive longer but also the juice spent on keeping the data buffered.
The data computed is the same data computed at any speed (unless you lose data along the way...) but the power spent on completing that operation is not equal - not by a long shot.
On single core older processors where you are talking about a couple hundred megahertz one way or another the equation is much different, significantly diminshed returns on electricity invested, but with higher quality and multi-core processors especially they can cut through the data with significant ease when sufficiently powered.
But this is on processor intensive activities, and gaming is the first thing that comes to mind. For most other use of the device it's worth underclocking it and you will see battery gains.
So I have a few apps... Voltage Control, SetCPU, No-Frills CPU... but I've honestly been a bit weary to use them. I want the best battery life since I'm a heavy user, but I also don't want to overclock/set voltage to a point where I'll screw up my phone. I'll admit that I'm a novice user when it comes to voltage/overclocking, but not when it comes to ROMs, kernels, bootloaders, etc. I work with those all the time, but really trying to get the most out of the battery and CPU.
There's this thread I found that has someone's settings on it, but don't know if its good or how much this guy knows(no offense to him):
http://forum.xda-developers.com/showthread.php?t=1356211
Anyone got any insight or perhaps screenies of their optimally tested settings? VERY VERY appreciated to anyone that can help.
jgruberman said:
So I have a few apps... Voltage Control, SetCPU, No-Frills CPU... but I've honestly been a bit weary to use them. I want the best battery life since I'm a heavy user, but I also don't want to overclock/set voltage to a point where I'll screw up my phone. I'll admit that I'm a novice user when it comes to voltage/overclocking, but not when it comes to ROMs, kernels, bootloaders, etc. I work with those all the time, but really trying to get the most out of the battery and CPU.
There's this thread I found that has someone's settings on it, but don't know if its good or how much this guy knows(no offense to him):
http://forum.xda-developers.com/showthread.php?t=1356211
Anyone got any insight or perhaps screenies of their optimally tested settings? VERY VERY appreciated to anyone that can help.
Click to expand...
Click to collapse
there is no rule. every cpu is different. very different. my captivate took a lot of effort to get a meer 1300 mhz but my infuses get 1600 no problem at all. some infuses wont go to 1600 but more will go to 1500 than galaxy s's. they probably held out the best testing cpu's for the higher clocked phone.
for battery life try clocking @ 800 mhz and dont use screen off profiles just because it looks like a good idea to slow the cpu when you arent really using it(causes problems if the max freq is too low with some kernels) and test stability with your uv settings, go down a little at a time, for max frequency uv from the top down, for battery life go from the bottom up and disable the upper freqs if they become unstable. this is because rapid voltage changes can contribute to instability. too much differential will cause crashes if the uv is extreme or the oc is extreme.
at some point though the cpu settings will have a limited effect. the radios use battery as well. manage your screen brightness and try edge only with the screen off using any number of apps that manage the radio. try one of entropys kernels to avoid a feature of the wifi chip (or was it bt) from sucking power when in proximity of another device with the same chip. turn off sync if you dont need push emails from gmail or real time facebook updates and if you really need battery life get in the habit of togging wifi and bt and gps on and off depending on need. i do none on this because i always found the battery life adequate on samsung phones but on my aria, well it was a must and prolly why people hate android. htc and battery life dont go together unless you manually manage the phone functions.
That's a great bunch of information. I currently keep my Brightness at 0%, GPS off, Wifi only ON when I'm at work when the charger is plugged in.
I guess I'm more concerned with the undervolting than the overclocking. I'd rather preserve the battery life with undervolting... the overclocking isnt a HUGE concern, but it'd be nice to see. Regardless, if you have any "ideal" UV settings, or ones that have worked for YOUR Infuse(assuming you have one), then I'd love to see them.
at one point i had -200mv on every freq from 100-1600mhz and no crashes. i started manually editing the uv script (voltage control is only able to write -200 into the script unless you have the pay version) and forgot what i ended up with. but my first infuse was exceptional in that area. some infuses freeze above 1400 mhz no matter what voltage settings are used. about -50 seems to be safe 99% of the time with minor or no overclock across the board but you could probably go -50 down low and -100 from 400mhz up to 1200 and -50 or -75 on overclock freqs. with underclock or atleast no overclock it's probably safe to go -100 to -150. it may be safe to go much more than that as well but on a small number of phones that might be too far as it is. cpus are made on such a small scale that microns of inconsistency make large percentages of difference. many dont pass testing and qc. some are borderline for the application, some are exceptional. the smaller the architecture gets the more potential the design has for speed but the larger the variance in performance is given a manufacturing technique. obviously the manufacturing gets better and better combating this so that they can make smaller architectures they also have redundancy built in, but sometimes they just disable features of a chipset and market it as an economy version if they have a low pass rate. ever see a 3 core cpu for a pc? most are manufactured as 4 cores and on many motherboards the bios can unlock the 4th core with somewhat unpredictable results.
Again, some really great info for the technical guys such as myself. What is the best way to test the UV settings? The built in tools and stuff in SetCPU? Or is there another way that would be more effective and/or would get more realistic results?
This is my third time typing this... (This website should really have an auto-save draft feature)
I recently installed the application "CPU Tuner" because I've always wanted to utilize my newly rooted phone. The phone is running Cyanogenmod 7.2 Stable, and currently overclocked at 1.5GHz. My main concern is overclocking my phone that high. Now, I didn't really choose that option, SetCPU automatically set it to that when it loaded a configuration. I'm a beginner to overclocking, and this is my first time doing it for anything. I've heard rumors of people melting their processors from overclocking it, so I want to know if it's okay if its overclocked to roughly twice the stock frequency of 800MHz. If it IS safe, then why isn't the phone automatically set to 1GHz to compare to it's twin, the Evo 4G? Or perhaps even 1.2GHz to surpass it? I would definitely be satisfied with 1.2GHz, but I wouldn't mind having 1.5GHz if it was stable and didn't drain the battery. On to the next question, would an OC this high cause instability and/or would it drain my battery? I only overclocked an hour ago, so I haven't experienced any problems whatsoever... yet. On to the profiles... I'd like some suggestions for improving my triggers. Right now, it set everything up to the highest frequency, but looking at the help, it said to not touch the frequency, but experiment with thresholds. In the Help, it doesn't tell you what the thresholds are, and what they do, and more importantly, how they work. It just shows that the highest is the most battery saving. I would have thought the lower the better, but... Anyway, if you could tell me, I'd be highly appreciated it. Finally, the battery temperature... It has an option to enable a setting to change profiles if the battery gets a certain temperature, but I'd like to know what would be considered "Overheating". I get paranoid when the battery temperature gets a little warm at around 36 Celsius... but the profile it switches to is supposed to really slow down the CPU to preserve battery, so I'd really rather not use it unless it's necessary. So, would 45 - 50 Celsius do, or should I set it a bit lower? My battery is 4000+ mV, if that'd help at all. If you know any sources that you can direct me to that would answer my questions, it'd be highly appreciated.
Wow ok . Well first off check out THIS thread. It will explain a lot about Governors, I/O Schedulers, and a bunch of the questions you have. As for people melting CPUs, I've never actually seen it happen, or know anyone who has had it happen on the Shift. That's not to say it's not possible. It may be, just not probable. The Shift processor compared to the OG EVO's is much better. The Shift even at the stock 800mHz out performs the EVO's processor at 1000mHz. That is in part because it is a 2nd Gen processor vs the EVO's 1st Gen Unit. The Battery Temp should try and always be kept below 115-120 Degrees Fahrenheit. I use SetCPU, and have a Profile that kicks in to lower the OC to around Stock should the Battery Temp every reach 110 Degrees Fahrenheit. My setting are 61mHz Min 1516mHz Max, Smartass V2 Governor, and SIO Scheduler. But every device is different, so your going to have to do a bit of experimenting till you find what works for you. If you get a lot of Random Reboots, lower your Max OC setting, or try a different Governor. BTW where did you get a 4000mAh Battery?
prboy1969 said:
Wow ok . Well first off check out THIS thread. It will explain a lot about Governors, I/O Schedulers, and a bunch of the questions you have. As for people melting CPUs, I've never actually seen it happen, or know anyone who has had it happen on the Shift. That's not to say it's not possible. It may be, just not probable. The Shift processor compared to the OG EVO's is much better. The Shift even at the stock 800mHz out performs the EVO's processor at 1000mHz. That is in part because it is a 2nd Gen processor vs the EVO's 1st Gen Unit. The Battery Temp should try and always be kept below 115-120 Degrees Fahrenheit. I use SetCPU, and have a Profile that kicks in to lower the OC to around Stock should the Battery Temp every reach 110 Degrees Fahrenheit. My setting are 61mHz Min 1516mHz Max, Smartass V2 Governor, and SIO Scheduler. But every device is different, so your going to have to do a bit of experimenting till you find what works for you. If you get a lot of Random Reboots, lower your Max OC setting, or try a different Governor. BTW where did you get a 4000mAh Battery?
Click to expand...
Click to collapse
Thanks for the response. It's pretty late, so I've bookmarked the link to read tomorrow. Alright, so 45 degrees Celsius should the maximum then. I've been thinking of switching over to SetCPU, since there are more comprehensive guides than for CPU Tuner (In which no one seems to have heard about), and it doesn't seem that the settings it set will be ideal for the long run. Although, before I switch over to SetCPU, I want to at least give it a shot. I'll change my settings so that the frequency decreases depending on battery level. Also, I don't have much but the basic governors and configurations on CPU Tuner, so I've never heard of Smartass V2 (Prior to skimming through the link you posted). Also, the battery came with it, I knew it seemed a bit different from most other batteries (From what I've seen in searches, most of them had around 2000), but I didn't know it meant that much.
The Governor settings available will depend on the Kernel, not on the CPU Controller. I've always been partial to SetCPU, but that's just me. I would again suggest doing a bit of reading, and experimentation to find your best settings. But defiantly the closer to normal the Battery temperature is the better. When the Battery heats up to much it will in most cases also drain faster. If you can post a Pic of the Battery I would really like to see it. I've never come across a 400mAh Battery for the Shift.
When I first rooted my shift 2 years ago I was very concerned of over-heating. I constantly checked the temperature. After a while I realized it is quite hard to over heat and cause damage, especially with the newest kernels the devs have put out. Just experiment with different settings and see what works best for your phone
Sent from my PG06100 using xda app-developers app