Please advise me, what settings are the best for HTC Desire S (SHADOW HAWK V2.0|Sense 3.0|Android 2.3.5[2.10.401.8] ROM)?
Or give me a link where I can read what mean: VOC1, VOC2, VOC3, UV1, UV2 pages?
It's really not hard to understand,
VOC 1 2 and 3 are 3 profile of CPU frequency tweakers :
Here you can chose the governor and the frequency of the CPU
You can set wake and sleep governors, low frequency and high frequency.
With Hyperion kernel, i set
ondemand
245000
1152000
conservative
245000
614400
I don't know if you can OC/UV with a stock kernel.. Maybe someone can answer you better than me.
And it's really fluid and low battery eater.
UV1 and 2 are profiles for CPU voltage tweakers
CPU voltage tweak can affect the stability of the system.
The lower the voltage is the greater the battery life is.
I advise a -25mv every where (ALL -25)
But not more, i had stability issues with -50 and more.
I know how to set a cpu clock but I don't understand those profiles onemand, virtuous, conservative etc. Could someone explain me the diffrence between them?
IT.Adviser said:
Please advise me, what settings are the best for HTC Desire S (SHADOW HAWK V2.0|Sense 3.0|Android 2.3.5[2.10.401.8] ROM)?
Or give me a link where I can read what mean: VOC1, VOC2, VOC3, UV1, UV2 pages?
Click to expand...
Click to collapse
if you are using stock kernel then you cant OC or UV
but if you use a custom kernel like Hyperion kernel you can OC /uv
VOC1 is for setting the frequencies
this is what i use
wake
governer: virtuous
min:384000
max:1228800(you can set it higher if you have any lag)
sleep
governer: conservative
min:245000
max:384000
press perm activate button
VOC2,VOC3 are like more profiles which you can switch to when needed
UV1 is for reducing/increasing voltage
if you are using hyperion v2.0 kernel you can uv by -50 (-25 if you have stability issues)
to do this press all -25 twice & then press perm activate
If you are going to change UV settings use the temp activate for a while cause if the phone freezes it will revert to stock settings on reboot
Sent from my HTC Desire S using XDA App
These are called governors. They control the way the CPU ramps up between the maximum and minimum frequency. Go to setcpu's website for a list of descriptions between all the different governor s
Right, setcpu homepage explained me everything.
kartkk said:
if you are using stock kernel then you cant OC or UV
but if you use a custom kernel like Hyperion kernel you can OC /uv
VOC1 is for setting the frequencies
this is what i use
wake
governer: virtuous
min:384000
max:1228800(you can set it higher if you have any lag)
sleep
governer: conservative
min:245000
max:384000
press perm activate button
VOC2,VOC3 are like more profiles which you can switch to when needed
UV1 is for reducing/increasing voltage
if you are using hyperion v2.0 kernel you can uv by -50 (-25 if you have stability issues)
to do this press all -25 twice & then press perm activate
Click to expand...
Click to collapse
Thanks Kartkk for the info. I am using the Endymion sense 3.5 ROM with the Endymion Kernel V2 on my Htc Desire S. Sorry for being such a noob at this but just wanted to ask you lot soemthing. Users on that forum somehow seem to get Quadrant Scores of over 2000, I only manage score upto like 1750 with the settings you have mentioned above. Please Advise.
Thanks in advance.
I'm running a pre-rooted, deodexed 2.3.5, and have now tried 2 different kernels (unity and hyperion) and while I can make changes in SetCPU, I'm unable to alter tin UV settings in UV/OC beater because the kernel doesn't allow it.
Does anyone understand why this might be? X
Default undervolt values
Can someone please post the default undervolt values for the respective frequencies. I want to set back my phone to the default voltage. Thanks allot
OV is risky business if you ask me
I have htcdev unlocked DS (after ics ruu) S-on,...
I guess that some kernels allow UC/OC and UV/OV but some don't. I only tried two diffident roms fallout v5 which allowed both, but now I running finnys JB 4.2.1 rom which allows only UC/OC but not UV/OV(according to pimp my rom app).
Benchmarks cores; fallout5 antutu score: 4600, JB antutu score: 4050 but JB runs faster, smoother, slicker
And if you cannot find default values just restore nandroid backup image, and then look for values there.
Read new informations in installation guide
Click to expand...
Click to collapse
Click to expand...
Click to collapse
IF YOU HAVE REBOOTS WHEN YOU ARE USING THE PHONE, IT'S BECAUSE YOU SET A UV TOO AGGRESSIVE, SO, YOUR CPU CAN'T BE STABLE. CHOSE A LOWER UNDERVOLTAGE
IF YOU WANT TO KNOW HOW VOLTAGE CAN REACH YOUR CPU, START STABILITY TEST (DOWNLODABLE FROM MARKET) AND USE IT FOR ABOUT 10 MINUTES, IF PHONE REBOOTS IN THAT TIME, THAT VOLTAGE IS TOO LESS FOR A STABLE CHIP
NOT ALL CHIP ARE THE SAME, IF YOU HAVE A LUCKY CHIP, YOU CAN REACH A LOWER VOLTAGE (AS MINE)
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Ok Guyz, since show creates the badass governor, i'd want to use it for a better one multicore configurtion
What's the advantages of multicore sistem?
Symply, more parallelization means more performance per second, as i can say, 2 core can compile at last the double quantity of threads than 1, so, 1 core at double frequency can't compile the same number of thread, but it do it faster..
ex..
if you have 2 thread (impossibile), 1 audo and 1 video, a single core @ 2ghz compile firstly the audio, than the video.. the dualcore architecture can compile on core0 the audio and on core1 the video!! this is the powerfully of multicore system.
Ok, since i say it, i create a MOD witch TRY to use this logically.. this MOD uses the limitate frequency of the badass governor, that's why, with ondemand, all of 2 core goes at maxFreq too fast, now, with this badass, the system will not grow up the first limitate frequency until the single core uses more than that frequency.. so.. we can limitate the "ondemand" issue in 3 freq phases..
thus, the actual MOD configuration is it:
Click to expand...
Click to collapse
SCREEN ON:
- dualcore with all cores TURNED ON (hope you understand now )
- governor badass for all of 2 cores
- min freq at 384mhz for all of 2 cores
- max freq at 1.566ghz for all of 2 cores
- first phase freq at 810mhz for bla bla bla
- second phase freq at 1.188ghz for bla bla bla
- third phase freq at 1.566ghz (is the maxfreq)
SCREEN OFF:
- only core0 is TURNED ON
- governor conservative
- minfreq 192mhz
- maxfreq 540mhz
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Badass governor has the same configuration as last show's ondemand governor
So, now, with this MOD we have a pure functional dualcore with the advantages of multicore system, with limitate frequency. The stock situation is 384-810mhz, if the single core (is the same, qualcomm uses asyncronic frequency) needs more than 810mhz, it increases the max freq to 1.188ghz (the sensation original frequency), if 1.188 isn't sufficently, it increeses at 1.566
remember, qualcomm has asyncronic frequency, so, one core can be run at 1.56ghz, the other at minimum mhz..
Click to expand...
Click to collapse
Click to expand...
Click to collapse
How to use it?
Click to expand...
Click to collapse
INSTALLATION:
-) flash a kernel witch has badass governor (i advise bricked 1.1) with NO GPU OC and what governor you want, the same for the frequency, mod autochanges those, chose what scheduler you prefer.
1) Flash MOD zip file by recovery
2) Select what MOD YOU want
3) Reboot.
#) You have to reinstall at every Rom Upgrade
# If you want only the UV, select Remove in mod choseing (it's the same as no installing it); you can use the UV mod with all kernels, and all governors
# If you come from V2.0 to 3.0, go to recovery, wipe, format system partition, after that, reinstall rom, reinstall bricked kernel (if it hasn't), reinstall other mods (like battery %), install my mod, reboot.. You will not loose your data
# ONDEMAND VERSION IS NOT FOR GOOD BATTERY CONSUPTION, IF YOU HAVE HUGE BATTERYDRAIN (IT'S WHAT YOU'LL HAVE) INSTALL THE BADASS - BOOST+BOOST VERSION.
DISINSTALLATION:
1) Boot in recovery, flash the Mod
2) Select Remove
3) Reboot
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Code:
bricked 1.2 -above
V 11.9
> Fixed Screenoff chose
> Changed DEFAULT first phase for better reactive with less power usage
> Other minor changes
###
Added Version for AOSP kernel (NoSense)
V 11.8
> Changed some settings
V 11.7
> Changed some settings for a better fluidity
V 11.6
> Added Remove chose
> Fixed an installation issue of the Aroma
V 11.5
> Added possibility to know if MOD is working, you have to give a cycle on/off of the screen, after that, if it works, you will find a new file in home of sdcard!
V 11
> Changed configuration for less battery drain
V 10.5
> Tweaked badass experience for better battery life (only with bricked kernel 1.4)
V 10.1
> Tweaked screen off conservative
V 10.0
>> BIG RELEASE
> Added possibility to chose frequency
> Added possibility to chose screen off governor
V 1.01
> Fixed freq values in Aroma installer
V 1.0
> Initial Release
HaVe FuN!
Click to expand...
Click to collapse
Click to expand...
Click to collapse
FAQ in second post
VIDEO
Click to expand...
Click to collapse
FAQ
Click to expand...
Click to collapse
Witch version could you chose?
The versions of the mod are two:
The 3.7 is the older, it's for the bricked 1.1 version AND for other kernels (don't know if all rom will boot up with my mod, some has issues)
The version 10 and above are for bricked 1.36 and 1.40
What setting could you use?
You can intall what you want, i create those (expecially the 10 versions) witch has the possibilities to be changed as users experience.
I advice to use default settings if you don't know how change, but, you should try to, it will not brick your phone, in fact, you could find a new setting could it be better for your use.
So, try try try
One EX:
If you want a faster phone, grow up the minfreq to 300-400mhz, grow up the first phase at 1.2ghz, put the second to 1.2 or more, and change the maxfreq as you would, OC too.
If you want a better battery experience, decrese minfreq, the first and second phase, decrese the maxfreq too, maybe, with this settings: 192 - 648 - 1020 - 1180 mhz
If you want the lowest battery experience, try with this setting: 192 - 648 - 1020 - 1020 mhz
Be careful, you could have some lags if you chose the lower setting, but, for ex, if you don't play, you can chose a setting as like, 192 - 810 - 1020 - 1180 mhz
So, you have to install, select one setting with you think it's ok, try, if you have lags in some situation, grow up some setting, an re-try til you find your best settages. I don't have your use, so, i don't know if you could have a good esperience with my setting.
How to see if mod is working?
If you have the version 10 or above, you will find a new file in SD card, it calls IBA21ModWorking. if you don't find that, turn on the screen, wait 5 seconds, turn on, refresh the explorer app, and try to see if there is.
If you have the 3.7v you have to download and install system tuner, and see if all cores are turned on.
Why my phone doesen't boot after apply the mod?
Not al roms has the same quality, some doesen't have some little features; my mod uses a whyle cicle witch chages settings from screen-on use to screen-off (standby). If phone doesen't boot up, rom doesen't have the possibility to use the cycles in the script, so, script is unusefull.
Do you need to delete or wipe the rom at every upgrade?
ABSOLUTELY NO, mod auto removes the old script and changes that with the newer one, so, YOU DON'T NEED TO DO ANYTHING, ONLY FLASH THE UPGRADE OR THE NEW SETTINGS WITCH YOU ARE CHANING!
Click to expand...
Click to collapse
Click to expand...
Click to collapse
enjoy my work and, press a lot of thanks buttons! :d
Very very good, the system is smooth and stable, I've only a lag after reboot, and sometimes when start synchronization...
Good work!
Hi nice script. Must the CPU values be truly stock ? Could it take something like 384-1566?
Sent from my Sensation running HyperNonsense v2.3
remus82 said:
Hi nice script. Must the CPU values be truly stock ? Could it take something like 384-1566?
Sent from my Sensation running HyperNonsense v2.3
Click to expand...
Click to collapse
Yep, i could do it.. but.. i tryed it, and.. it only increase the power consuption
framir said:
Very very good, the system is smooth and stable, I've only a lag after reboot, and sometimes when start synchronization...
Good work!
Click to expand...
Click to collapse
Lags depends on badass governor.. it's "normally".. but.. 1 lag per day is not bad, remember, with my configuration you have a better badass configuration with lower power consuption than faux kernel..
Looks awesome
Noticed bug appears after every reboot?
How to change second phase to 810-1134 and delete third phase? Or I don't need it
And soo.. It's fully better than original badass?
http://i.imgur.com/gavOn.png
Standby power consuption with data active!
D-SHEL said:
Looks awesome
Noticed bug appears after every reboot?
How to change second phase to 810-1134 and delete third phase? Or I don't need it
And soo.. It's fully better than original badass?
Click to expand...
Click to collapse
You don't need to delete it since system uses third phase (1.2 to 1.5) only in heavy games and web browsing+flash player.. in web usage cores goes to 1.2 max
Btw.. third phase is the maxfreq governor.. i can change it by script if you want to try
Take.. flash it as you would.. you can come back with stock script
For who doesen't understand.. the phase limis is a real limit.. since system needs more performance, system use the lower limit.. as i can see in my use:
For home scrolling 1 core goes to 1.2ghz, the other is at 192mhz (low power consuption)
For notice bar scrolling 1 or 2 cores goes to 810mhz, it depends on other app.. 1 core at 810mhz can calculate the notify bar
For chrome beta browsing.. in web rendering ( page loading) all of 2 cores goes to 1.2ghz, after that, core goes to 192-810 since heavy scrolls, heavy zoom, or animations in the web page (in google page cores goes to 192mhz )
For browser + flash player, 2 cores are uset at 100% at 1.56ghz since it comes down.. after that.. system uses 192-810.. sometimes only one core goes to 192-1.2
In games core i dont know why i dont play games
So.. the third pase is only a turbo boost, it's used only when system needs more and more power.. the phase is a real limit..
For example.. you have a stock 192-810.. when system needs more than 100% (810mhz) badass grow up the frequency to second phase.. it's the same for third phase.. so.. if system doesen't need more power, badass doesen't grow up the cpu frequency..
In my test i see.. ondemand tweaked + core1 off at my usage has a cpu temperature at about 55degrees C.. with badass, 47
So.. lower tenperature.. lower power consuption!
Sure.. ondemand has a faster one response.. since it grow up frequency every time, for low needs too..
you couldn't have performance plus heavy power..
The "busg" is too.. until system needs more than phase freq, it doesent grow up, so, when there's the necessity of more freq, upgrading is slower than ondemand, and it creates a little lag..
On boot, don't know why but.. only one core is turned on.. it's a system fault of reading script.. if you turn off screen, and turn on, it returns at normally (so.. needs an off-on cicle)
iba21 said:
You don't need to delete it since system uses third phase (1.2 to 1.5) only in heavy games and web browsing+flash player.. in web usage cores goes to 1.2 max
Btw.. third phase is the maxfreq governor.. i can change it by script if you want to try
Click to expand...
Click to collapse
Thanks! Maybe really don't need this
Noticed bug appears after every reboot?
"69force192-1188.zip"
As I can see, this is version without third phase?
D-SHEL said:
Thanks! Maybe really don't need this
Noticed bug appears after every reboot?
"69force192-1188.zip"
As I can see, this is version without third phase?
Click to expand...
Click to collapse
Yep that has only 2 phase.. 192-810 and 810-1.2
I edited last message with informations about your questions
Shouldn't this be in the Development section?
nope.. it's not a developement app.. those are some settages..
if you load the script, and delete it, the settages has been changed..
when you turn on display
screen ON:
- dualcore able
- governor badass for all of 2 cores
- min freq at 192mhz for all of 2 cores
- max freq at 1.566ghz for all of 2 cores
- first phase freq at 810mhz for bla bla bla
- second phase freq at 1.188ghz for bla bla bla
- third phase freq at 1.566ghz (is the maxfreq)
when you turn off
screen OFF:
- only core0 able
- governor conservative
- minfreq 192mhz
- maxfreq 540mhz
it changes that values at every turn on-off of the display.. only 1 time.. so.. if you load the script, and delete it, at display turning off, the script doesen't change the values, and, you will not have the "screen off" setting, so, you'll have the stock badass, so, more power consuption
i repeat, my script is only a numerical setting, it's not a kernel, it changes only the superficially values of the kernel, after that, is the kernel governor the real fault of frequency changing
sure.. with my script you have that 2 configuration.. and.. if you see.. conservative in standby means low power consuption (from 20 to 70ma in standby, depends on the system performance needed)
Is step 6 necessary? I don't have that function in root explorer
Sent from my Sensation running HyperNonsense v2.3
remus82 said:
Is step 6 necessary? I don't have that function in root explorer
Sent from my Sensation running HyperNonsense v2.3
Click to expand...
Click to collapse
it's not obbligatory.. but.. you have it.. long press.. OPEN WITH -> LINUX script (it's the third link from top)
http://i.imgur.com/BbeS0.png
Or you can reboot 2 times.. in first run script changes the name of the file witch turn on the second core.. the mpdecision.. so.. or you do a first manually run.. or you do a first reboot.. script changes the name, but the mpdecision script is already loaded.. second reboot use only my script
Thanks! Will report back after a day of use!
Sent from my Sensation running HyperNonsense v2.3
Edit: solved.
Sent from my Sensation running HyperNonsense v2.3
Iba I notice that media scanner takes extremely long to complete after applying the script. Is it possible to use badass or on demand as screen off governor?
Sent from my Sensation running HyperNonsense v2.3
Sure.. but you loose the advantages of low power consuption..
What is media scanner? How many mhz does it needs?