[Q] Tried to Install MIUI, Now Stuck - Samsung Infuse 4G

Welp I am one of the stupid ones and installed MIUI on my Infuse, and like everyone else, I'm stuck on the boot screen. I looked at the post on the same topic and tried to do it but couldn't get it to work probably becuase the computer says that its an Unknown device instead of a Samsung device.
So my question is what do I do now that my computer doesn't recongize the phone as a device anymore?
Thanks to all that can give help.

http://forum.xda-developers.com/showthread.php?t=1116251
And lesson learned - never install a ROM from another phone.

Yeah I know that now. Foolish mistake I know I shouldn't have made.
But, I have tried using that but when I connect the phone to the computer it shows to be an unknown device and Odin doesn't pick it up at all. My problem is, is that the computer doesn't recognize it as an Android Device anymore. Is downloading the drivers from Samsung going to help?

I'll have to leave that to someone else - I use Heimdall on a Linux box, I've never flashed from Windows.

Oh, ok. Well thanks for your help .

I fixed my problem. What I had to do was get another computer that doesn't have the Samsung Drivers or Kies installed and then install them. Once that was done Odin found the device and I was able to restore it.
So there's a tip for anyone who can't get their device to be recognized by the computer or Odin itself.

Or just uninstall/delete those drivers?

Entropy512 said:
I'll have to leave that to someone else - I use Heimdall on a Linux box, I've never flashed from Windows.
Click to expand...
Click to collapse
i have started to do this to since i got the infuse. ill tell you i dont miss driver issues one bit! linux/bsd/mac/whatever rock as long as you have supported hardware and that is becoming less and less of a problem these days.

re: Now Stuck
You need to try and pull the battery out and put it back see if you can get the phone into "download mode". If you cannot get it into download mode by doing that or using the up/down volume and power key combo then I would suggest that you purchase a "jig" on ebay. (they cost under $10 bucks shipped).
Here is the ebay link for the jig:
http://cgi.ebay.com/Samsung-Galaxy-...0563626533?pt=Cell_Phones&hash=item20ba3eba25
With a jig all you would need to do is to remove battery, plug the little jig into the usb port of phone and replace the battery, then wait 5 seconds or so and the phone will be in download mode allowing you to use Odin3 and flash back to "stock rom" to start with..
Best if you did that using the "Ultimate Unbrick" stock froyo rom after that
you can install infuse 1.5 custom rom or Bionix or the defused custom rom or any other rom.
Here is the link for the Ultimate Unbrick:
http://forum.xda-developers.com/showthread.php?t=1116251
Good luck.

nstong said:
Or just uninstall/delete those drivers?
Click to expand...
Click to collapse
I tried that but it didn't work on my computer, but that's just my computer that could work for someone else. If that doesn't work though, you can get another computer and install the drivers on them and that should work.

SamsTechAnswers said:
I tried that but it didn't work on my computer, but that's just my computer that could work for someone else. If that doesn't work though, you can get another computer and install the drivers on them and that should work.
Click to expand...
Click to collapse
Where are you trying to uninstall the drivers from? I have windows 7 and went to device manager or whatever and took it off there. Then reinstalled kies, worked perfect after.
Sent from my SAMSUNG-SGH-I997 using XDA App

Entropy512 said:
http://forum.xda-developers.com/showthread.php?t=1116251
And lesson learned - never install a ROM from another phone.
Click to expand...
Click to collapse
and.... do not touch if it works properly

I guess this is a good sign. Our phone is gaining popularity because new people are buying it and trying dumb things with it

Related

[Q] Can anyone help unbrick my phone...

I tried running Odin to unbrick back into recovery, but apparently didn't have the drivers installed (to my surprise). I hate to say it but I think I've reached the point of no return...any help would be very much appreciated.
Edit: I can't even get into dl mode and I don't have the samsung logo on the screen anymore...just a phone and computer logo.
May be you are not in dowload mode correctly.
For download mode:
1. remove battery
2. connect phone to computer
3. put battery
4. press volume up and down buttons only (no power button)
Try these steps, hope its helpful.
As far as the driver issue is concerned, downloading "Kies" is the easiest way. The phone doesn't actually work with the software, but the process of installing it will take care of any driver issues.
Search Kies in google to grab the download.
Try one click unbrick ^^ it work on mine
Sent from my SAMSUNG-SGH-I997 using xda premium
terr_bear said:
I tried running Odin to unbrick back into recovery, but apparently didn't have the drivers installed (to my surprise). I hate to say it but I think I've reached the point of no return...any help would be very much appreciated.
Edit: I can't even get into dl mode and I don't have the samsung logo on the screen anymore...just a phone and computer logo.
Click to expand...
Click to collapse
That is a download mode. It's just your Infuse saying man, something ain't right and I ain't going no farther.
Just install the samsung drivers, plug the phone in, let the drivers install and then run Odin.
atrix4nag said:
May be you are not in dowload mode correctly.
For download mode:
1. remove battery
2. connect phone to computer
3. put battery
4. press volume up and down buttons only (no power button)
Try these steps, hope its helpful.
Click to expand...
Click to collapse
According to your directions, I did it correctly...I was at a point where I could get into download mode, but I can't anymore...?
Zaidin said:
As far as the driver issue is concerned, downloading "Kies" is the easiest way. The phone doesn't actually work with the software, but the process of installing it will take care of any driver issues.
Search Kies in google to grab the download.
Click to expand...
Click to collapse
Downloaded kies to my computer...when I synced up it couldn't identify the device. I did a good amount of research before posting here...nothing seems to work
abcvn said:
Try one click unbrick ^^ it work on mine
Sent from my SAMSUNG-SGH-I997 using xda premium
Click to expand...
Click to collapse
I'll give that a shot and let you know how it goes...thanks man
Truckerglenn said:
That is a download mode. It's just your Infuse saying man, something ain't right and I ain't going no farther.
Just install the samsung drivers, plug the phone in, let the drivers install and then run Odin.
Click to expand...
Click to collapse
That's the thing...odin would be a breeze, but I just can't get the right drivers for odin to id it...so I guess my solution would be to get kies to id my phone so I could dl the drivers and run odin, right? Easier said than done I suppose...
Thanks for the feedback guys, I really do appreciate it...
Don't plug in your phone at all. Open up Kies/Kies Mini or whatever you have, and under the options it should have an option to install drivers. Once they are done, close kies, reboot your computer, open up Odin with whatever you are flashing, and then plug your phone into download mode.
nygfan760 said:
Don't plug in your phone at all. Open up Kies/Kies Mini or whatever you have, and under the options it should have an option to install drivers. Once they are done, close kies, reboot your computer, open up Odin with whatever you are flashing, and then plug your phone into download mode.
Click to expand...
Click to collapse
Thanks, I'll give that a try too...
nygfan760 said:
Don't plug in your phone at all. Open up Kies/Kies Mini or whatever you have, and under the options it should have an option to install drivers. Once they are done, close kies, reboot your computer, open up Odin with whatever you are flashing, and then plug your phone into download mode.
Click to expand...
Click to collapse
So I shouldn't sync my phone to get drivers via kies?
terr_bear said:
So I shouldn't sync my phone to get drivers via kies?
Click to expand...
Click to collapse
No, the program itself can install them without the phone, at least kies mini will. Or you can just download the driver from here:
32 bit drivers: http://www.mediafire.com/?0b45zo7o75rc5d5
64 bit drivers: http://www.mediafire.com/?3dh4d6up72me9re
It said I successfully dl'ed the drivers, yet nothing has changed...used kies mini, restarted my comp, and tried to sync, but it still can't recognize the phone...hate to admit it, but I think I've exhausted just about every solution I could find or think of :/
get rid of kies. it's a useless program. also if it's open odin might not work, even if it's open in the background like in the system tray.
the drivers are in the most logical place you could think of. on the samsung website under device support.
http://org.downloadcenter.samsung.c...445/SGH-i997_Infuse4G_USB_Drivers_5_2_0_2.zip
http://www.samsung.com/us/support/downloads/at-t/SGH-I997ZKAATT
use the samsung cable if possible, others should work but on the older moment/intercept style phones a specific cable seems to be required. it couldn't hurt to make sure you have the correct cable.
even if you have the phone + computer screen it doesnt automatically mean you are in download mode. you may still need to do the download mode proceedure from battery pull (to make 100% sure the phone is off before you start the proceedure)
the best way is to
1 open odin
2 pull battery
3 connect the cable
4 phone should be face down
5 hold the volume buttons at the same time
6 with volume buttons depressed slide the battery into place
now you may see dwnload or you may see phone + computer or you may even see a black screen but there is a good chance that if the drivers worked that you will see a yellow box in odin
good luck
terr_bear said:
It said I successfully dl'ed the drivers, yet nothing has changed...used kies mini, restarted my comp, and tried to sync, but it still can't recognize the phone...hate to admit it, but I think I've exhausted just about every solution I could find or think of :/
Click to expand...
Click to collapse
Read what was said. Install drivers, close kies, reboot, open Odin.
Cranky...
KK4
Truckerglenn said:
Read what was said. Install drivers, close kies, reboot, open Odin.
Cranky...
KK4
Click to expand...
Click to collapse
I have tried everything, and windows 7 says the drivers are in place, but nothing happens! Trying heimdale, nothing is happeneing either.
Ryanscool said:
I have tried everything, and windows 7 says the drivers are in place, but nothing happens! Trying heimdale, nothing is happeneing either.
Click to expand...
Click to collapse
Heimdall uses completely different drivers which are installed via the one click heimdall using zadig.exe
---------- Post added at 02:52 PM ---------- Previous post was at 02:51 PM ----------
If you can get to download mode, you are not bricked, and it is an issue on your part.
nygfan760 said:
Heimdall uses completely different drivers which are installed via the one click heimdall using zadig.exe
---------- Post added at 02:52 PM ---------- Previous post was at 02:51 PM ----------
If you can get to download mode, you are not bricked, and it is an issue on your part.
Click to expand...
Click to collapse
I can not get anywhere, but i am installing the 64 bit drivers as im running win 7 64. I will try again, but for anyone else who has no other options and a tiny bit of cash there is some hope http://mobiletechvideos.mybigcommerce.com/samsung-infuse-4g-jtag-brick-repair/ . Suprisingly, this is not a scam as many, many people say it worked for them.
Ryanscool said:
I can not get anywhere, but i am installing the 64 bit drivers as im running win 7 64. I will try again, but for anyone else who has no other options and a tiny bit of cash there is some hope http://mobiletechvideos.mybigcommerce.com/samsung-infuse-4g-jtag-brick-repair/ . Suprisingly, this is not a scam as many, many people say it worked for them.
Click to expand...
Click to collapse
Get UnBrickable mod. That works well. I use it whenever I put my device into download mode. Just send me a pm and ill do it for $30+shipping. UBM lets you upload download mode to a device regardless of its state. I spent alot of time researching the methods and I came up with the mod for this device not too long ago.
UBM is the best option. Here is a demo on a captivate. We rewrote the HIBL for compatibility with the infuse4g
Thanks for all the help guys, but absolutely nothing I tried was working and I was short on time and patience...so you gave in to the JTAG unbrick service. I couldn't stand to pay for a service that I was sure I could perform myself, but when it got down to it, I didn't have time to deal with I all. I can confirm that it is a legit service. Great communication and Josh does quick work of getting things working again...I'm a firm supporter of DIY, but if you do reach the point of no return like I did, it's a very reliable resource.
terr_bear said:
Thanks for all the help guys, but absolutely nothing I tried was working and I was short on time and patience...so you gave in to the JTAG unbrick service. I couldn't stand to pay for a service that I was sure I could perform myself, but when it got down to it, I didn't have time to deal with I all. I can confirm that it is a legit service. Great communication and Josh does quick work of getting things working again...I'm a firm supporter of DIY, but if you do reach the point of no return like I did, it's a very reliable resource.
Click to expand...
Click to collapse
I have a suggestion. I also had this issue. The problem was my main PC. I simply used my old laptop and it worked like a dream. I know thus seems too simple but it has worked for several people.
Use GTGs Ultimate Unbrick on a different computer.
Just my 2ยข

I will never root, flash, or intsall anthying on my phone again!

I will never ever do anthying to my phone ever again! It does nothing but screw up your phone. Im better off wating for at&t to update my phone! My phone is still screwed up! Stuck in a so called "boot loop". I think i have tried everything! And these so called forums are suppose to help pshhh! I guess ill have to go to at&t and buy a new phone because they will know mine is rooted. Im so screwed!
Haha
Sent from my SGH-T989 using XDA App
Zach4G said:
I will never ever do anthying to my phone ever again! It does nothing but screw up your phone. Im better off wating for at&t to update my phone! My phone is still screwed up! Stuck in a so called "boot loop". I think i have tried everything! And these so called forums are suppose to help pshhh! I guess ill have to go to at&t and buy a new phone because they will know mine is rooted. Im so screwed!
Click to expand...
Click to collapse
Relax dude...
you haven't read enough.
Go to gtg unbrick and read
go to adams' one click and read
pick any of the Q&A "omg!! i'm stuck" "omg, i'm bricked" "omg, bootloop" and read a little bit..
Zach4G said:
I will never ever do anthying to my phone ever again! It does nothing but screw up your phone. Im better off wating for at&t to update my phone! My phone is still screwed up! Stuck in a so called "boot loop". I think i have tried everything! And these so called forums are suppose to help pshhh! I guess ill have to go to at&t and buy a new phone because they will know mine is rooted. Im so screwed!
Click to expand...
Click to collapse
Wow. Really? Rooting is the very first thing I do when I purchase a new phone. I rotoed my infuse the evening of the day I purchased it and didn't look back. So many options... So many great devs. Try being a little more patient. It will only benefit you in the long run.
stick with it...There are many threads, devs and tools here to use. Not sure why you are saying you can't get help....
What were you trying to do? Where are you now?
odin: http://forum.xda-developers.com/showthread.php?t=1092021
heimdall usage: http://www.youtube.com/watch?v=6TgyaUbjcm4
heimdall link: http://forum.xda-developers.com/showthread.php?t=1331381
click thanks
This phone is unbrickable and this is a useless thread man...close it
Sent from my SAMSUNG-SGH-I997 using xda premium
dman3285 said:
This phone is unbrickable and this is a useless thread man...close it
Sent from my SAMSUNG-SGH-I997 using xda premium
Click to expand...
Click to collapse
Ahhh someone help me. I am in a bootloop, and ive actually tried everything. (I know my stuff, do not get me wrong). Anyway I am on windows 7, and the drivers seem to be screwed up. Thank god, I have windows xp on an old computer im trying that now.
Rocket42 said:
stick with it...There are many threads, devs and tools here to use. Not sure why you are saying you can't get help....
What were you trying to do? Where are you now?
Click to expand...
Click to collapse
I tried to root my phone using this video on youtube: "How to root, install 3e recovery, and install custom ROM on Samsung Infuse"
I did everything correctly then when i booted up my phone it wouldnt boot, it just stays on the samsung screen. When i plug it up it just shoes an empty battery and doesnt do anything.
Ive tried doing gtg's ultimate unbrick, but odin3 wont recongnize my phone and i have the drivers installed.
Ive tried adams one click: but it keeps saying "disconnected" it doesnt say connect.
Any Suggestions???
qkster said:
Relax dude...
you haven't read enough.
Go to gtg unbrick and read
go to adams' one click and read
pick any of the Q&A "omg!! i'm stuck" "omg, i'm bricked" "omg, bootloop" and read a little bit..
Click to expand...
Click to collapse
Yes, i have done that. Ive been tryin to unbrick for 2 days.
Ryanscool said:
Ahhh someone help me. I am in a bootloop, and ive actually tried everything. (I know my stuff, do not get me wrong). Anyway I am on windows 7, and the drivers seem to be screwed up. Thank god, I have windows xp on an old computer im trying that now.
Click to expand...
Click to collapse
Yeah i have xp but as u can see im stuck.
If Odin is not showing #comm# then you do not have the proper drivers installed...bottom line...
Sent from my SAMSUNG-SGH-I997 using xda premium
dman3285 said:
If Odin is not showing #comm# then you do not have the proper drivers installed...bottom line...
Sent from my SAMSUNG-SGH-I997 using xda premium
Click to expand...
Click to collapse
Ok well it does not work on either computer. I rooted the dang phone so i had the drivers then..... when i try installing other infuse drivers ive had it says that they are already installed, where earlier i removed it by using the uninstaller. I am soo stuck.
make sure u have heimdall uckj4 downloaded to your pc
make sure you are in admin user
turn off your phone
get a decent usb cord
plug it into a different usb than what you have been using
put your phone into DL mode ( pull battery, press vol up and vol down, plug in usb and replace battery)
make sure you have updated to latest java
run the 1 click
it may show disconnected
install drivers using zadig - move thru the selections, find android usb
if you have install correct drivers, it should show connected
flash it
after it flashed the first time
flash it the second time with the bootloader box checked
if it works correctly, you should be on uckj4 stock att gb
if it doesn't work, you can always drive your car over the phone and ask for a replacement
Zach4G said:
I tried to root my phone using this video on youtube: "How to root, install 3e recovery, and install custom ROM on Samsung Infuse"
I did everything correctly then when i booted up my phone it wouldnt boot, it just stays on the samsung screen. When i plug it up it just shoes an empty battery and doesnt do anything.
Ive tried doing gtg's ultimate unbrick, but odin3 wont recongnize my phone and i have the drivers installed.
Ive tried adams one click: but it keeps saying "disconnected" it doesnt say connect.
Any Suggestions???
Click to expand...
Click to collapse
qkster said:
make sure u have heimdall uckj4 downloaded to your pc
make sure you are in admin user
turn off your phone
get a decent usb cord
plug it into a different usb than what you have been using
put your phone into DL mode ( pull battery, press vol up and vol down, plug in usb and replace battery)
make sure you have updated to latest java
run the 1 click
it may show disconnected
install drivers using zadig - move thru the selections, find android usb
if you have install correct drivers, it should show connected
flash it
after it flashed the first time
flash it the second time with the bootloader box checked
if it works correctly, you should be on uckj4 stock att gb
if it doesn't work, you can always drive your car over the phone and ask for a replacement
Click to expand...
Click to collapse
WTHECK is zadig?
Ryanscool said:
WTHECK is zadig?
Click to expand...
Click to collapse
it's the driver installing module that comes with the heimdall 1 click package by adam outler
qkster said:
it's the driver installing module that comes with the heimdall 1 click package by adam outler
Click to expand...
Click to collapse
Ok thnks, how do you get to this? NVM i got it, but it wont find the device in zadig ahhhh
I was having issues getting my drivers to work in download mode till I downloaded kies, then it worked fine and allowed Odin to read my device.
Ryanscool said:
Ok thnks, how do you get to this? NVM i got it, but it wont find the device in zadig ahhhh
Click to expand...
Click to collapse
look thru the options, there is an install drivers..make sure you pick the correct listed device...
zadig is different,,it doesn't require kies or any of the other drivers..it will install the usb drivers on only one of your port...save this port for future use with heimdall..
qkster said:
look thru the options, there is an install drivers..make sure you pick the correct listed device...
zadig is different,,it doesn't require kies or any of the other drivers..it will install the usb drivers on only one of your port...save this port for future use with heimdall..
Click to expand...
Click to collapse
Odd, has nothing there just my preinstalled camera. There is nothing to do with android, tried every single option lol. I still will not get it, should i remove microsoft c++ when it goes by that screen?

Please help me with download mode!!

Hello, i am currently trying to root my sisters galaxy s 4g... Her Baseband is T949VUVKI1. Firmware is 2.3.5, Build Number is GINGERBREAD.VUVKI1. i remember flashing her phone to 2.3.5 and download mode working perfectly fine, and for some reason it wont go into download mode at all... the computer is not recognizing her phone either. YES, i do have usb drivers installed otherwise my galaxy s 4g wouldnt be recognized on my computer(odin specifically, not turning yellow). Please help, i have searched everywhere in the internet and tried almost everything... Volume up and down and plug charger, batter out volume up and down usb and battery in etc. PLEASE HELP!! Thank You in Advance.
Nvm
10c
1. Try reinstalling to drivers. Also make sure you're using the same USB port as Windows can be funny about it it sometimes.
2. if download mode is being difficult, go download the Android SDK from www.android.com. Install it, run it, and only download the platform tools. When that's done, open a command promt, CD to where the plaform tools installed (either c:\program files\Android\Android-sdk\platform-tools or c:\program files (x86)\Android\Android-sdk\platform-tools ), then issue the command: adb reboot download.
3. I suggest you check the dev section for bhundven's one-click collection. Uses Java and Heimdall vs. ODIN and works easily.
Sent from my SGH-T959V using XDA App
i have this issue 2.3.5 messed me up. Odin sees my phone in debug mode but not in download mode...using odin 1.85 sinse it is the only version that responds to my phone at all. help please!
Tytan0007 said:
i have this issue 2.3.5 messed me up. Odin sees my phone in debug mode but not in download mode...using odin 1.85 sinse it is the only version that responds to my phone at all. help please!
Click to expand...
Click to collapse
Get it back into download mode, go grab a bhundven's one-click. The one-clicks utilize Heimdall vs. ODIN, which means they use open-source USB drivers instead of the proprietary Samsung drivers. See if that enables the computer to see the phone. If so, flash the one-click
Should I uninstall the samsung drivers prior to using Heimdall's One-Click?
Tytan0007 said:
Should I uninstall the samsung drivers prior to using Heimdall's One-Click?
Click to expand...
Click to collapse
That's a good idea. Some people have reported conflicts between the drivers.
Why would only Odin 1.85 see my phone in USB Debugging and not in download mode? And all other Odin verisions never see my phone, no matter what state it is in... I am at work so I will give the one click another try when I get home. I never thought of uninstalling the Samsung drivers prior to install; however, I did use the one click method to no avail. However, Heimdall's one-click was able to see my device it just kept giving me a driver error. This is so crazy it might just work.
Tytan0007 said:
Why would only Odin 1.85 see my phone in USB Debugging and not in download mode? And all other Odin verisions never see my phone, no matter what state it is in... I am at work so I will give the one click another try when I get home. I never thought of uninstalling the Samsung drivers prior to install; however, I did use the one click method to no avail. However, Heimdall's one-click was able to see my device it just kept giving me a driver error. This is so crazy it might just work.
Click to expand...
Click to collapse
I wish I had a good answer. ODIN's a funny animal. I've been fortunate and not had any problems with it. I am hoping you are correct - maybe it was just a driver conflict. Let me know how it goes.
didn't work...
You could try downloading a terminal app from the market. Open the terminal and type:
reboot download
See if that does it.
***Update***
Okay, so Oneclick was not working at all no matter what I did with the drivers. However, in all my tinkering with it I installed the Samsung Driver, the Open Source one, and some gadget driver as well from oneclick.
Doing this put all these drivers in my computer. Then I went into my Device manager (Win 7) and looked at my USB driver and I uninstalled everything and went to the stock win 7 usb driver. Then I plugged my phone in and my computer began searching for drivers for this device when it decided that it would be a good idea to load all three drivers at once and voila my phone was then showing up on ODIN 1.85.
I then proceeded to flash my phone with a rom, probably the wrong one considering I was coming from 2.3.5 and my phone boot looped and then soft bricked(sorry if I used these term incorrectly, noobin it).
After, some nervous moment of scouring XDA I found the god-send of a post on getting in to download mode, using odin, and flashing stock 2.3.6 - thank you Raver(I believe). When I did this, my phone magically started obeying ODIN like a devout viking and is now running 2.3.6 superbly.
Keeping with my phones newly found viking heritage, I intend to figure out how to properly root it, update the kernal and modem(not sure which one is best), get CWM, and subsequesntly put in Valhalla Black.
Seeing as though this last rendevous with flashing caused me a little scare I may hold off and wait to see what the next big update is (maybe a port ICS variant) and then go with that.
Anyway, thank you Stephen for helping me out with this and to everyone in this post.
Here's some reading for you Tytan,
http://forum.xda-developers.com/wiki/Samsung_Galaxy_S_4G#FAQ_.28with_answers.29
PS: Unless you wanna brick your phone, do not flash anything that isn't intended for the SGH-T959V Samsung Galaxy S 4G. You're saying you wanna flash a Vibrant ROM. You can, if you want an expensive paperweight. Happy flashing!
2.3.5 may have been for vibrant...yeah I think I got lucky. I did it prior to knowing about xda.
Sent from my SGH-T959V using XDA App
Tytan0007 said:
didn't work...
Click to expand...
Click to collapse
How are you getting into download mode?
There was a post in another thread where the person apparently was using the power menu to get into download mode or maybe the adb command.
Have you tried both the old fashion volume +/- and plug in usb cable? Or the adb command?
Do you have access to another computer? Believe it or not sometimes just changing computers will make the difference.
Weird when I replied there was no posts other than the ones on the first page...oh well glad its working now.

[Q] Need help getting my T959V connected for flashing/rooting.

Problem: Cannot get my Samsung T959V to connect to the computer in order to flash/root. Always gives the same "USB Device Not Recognized" error when I plug it in to the computer.
My Progress: Before you guys throw this questions out, let me tell you what I have tried so far. I have been trying to get this damn thing connected to the computer for about 3 weeks now. I have sat down on my computer going through the xda forum in detail trying to find an answer. I know the process of flashing and the xda contributors have some great guides to help us along the way, a big thanks to all ur hard work, but no matter what, I cannot get the phone in download mode or get it connected to the computer.
* I have read the Download Mode post and tried all 5 ways without luck.
* Have read all things related to Keis Mini and how it sucks when it comes to the T959V and other ppl have had the same problem.
* Have tried connecting in Keis mode, usb debugging mode but still the same error.
If someone can help me get my phone connected to the computer, I am sure I can take of the rest since everything is available on the SGS4G Bible, thanks for that also.
Is there anything I have missed or not tried yet? Please help. Thanks in advance for anyone who reads this post as it is my first. Usually I don't have to post since all the documentation is always up-to-date and available but this problem is killing me
Additional Information: Bought the phone from a cell-phone store I use to work at. Has Android 2.3.6 on it. Have done the factory reset and tried to get it to connect, no luck. Not sure if it has been flashed before, pretty sure it hasnt but the flashed download mode method didnt work also. Have android-sdk installed and have tried pointing the .inf file to the google usb-drivers in the sdk, no luck. Download both 32-bit and 64-bit drivers for this phone from multiple locations, still no luck trying to connect. Have also tried multiple computers and multiple v9 cables, no luck.
Have you installed the Samsung drivers? You mention google drivers but samsung has it's own. You should be able to find them in the noobs guide to Odin thread. DL mode should work as well regardless of what drivers you have installed. Pull the battery, plug usb into computer, plug phone into usb, hold down BOTH vol + and -, insert battery. I've never not seen that method work.
hechoen said:
Have you installed the Samsung drivers? You mention google drivers but samsung has it's own. You should be able to find them in the noobs guide to Odin thread. DL mode should work as well regardless of what drivers you have installed. Pull the battery, plug usb into computer, plug phone into usb, hold down BOTH vol + and -, insert battery. I've never not seen that method work.
Click to expand...
Click to collapse
Yup tried both 32-bit and 64-bit drivers on multiple computers. Tried the download mode method u said also. Trust me have tried everything I have read about and know, but no luck.
But the phone charges fine? Could be a bad USB port. Or partially bad. Have you tried a jig? If that doesn't work I'd say your hardware is screwed up somewhere.
hechoen said:
But the phone charges fine? Could be a bad USB port. Or partially bad. Have you tried a jig? If that doesn't work I'd say your hardware is screwed up somewhere.
Click to expand...
Click to collapse
Yup it charges fine. Both when I plug it into the wall and the computer. What's a jig? Don't think I have tried that yet. If something can let me know for sure its a hardware problem, then I will stop obsessing over this, hahaha. Thanks for ur help btw.
A jig is a nifty little device that plugs in to your USB port on the phone and then gets you to DL mode. Their mostly used to recvover from bad flashes(like flashing the wrong phones kernel). Here's a link:
http://www.ebay.com/itm/Download-Mode-USB-Jig-Samsung-Omnia-7-Galaxy-S-4G-/250877662279
If your cheap like me or just wanna make it fast here's a guide to making your own.
http://forum.xda-developers.com/showthread.php?t=1604707
hechoen said:
A jig is a nifty little device that plugs in to your USB port on the phone and then gets you to DL mode. Their mostly used to recvover from bad flashes(like flashing the wrong phones kernel). Here's a link:
http://www.ebay.com/itm/Download-Mode-USB-Jig-Samsung-Omnia-7-Galaxy-S-4G-/250877662279
If your cheap like me or just wanna make it fast here's a guide to making your own.
http://forum.xda-developers.com/showthread.php?t=1604707
Click to expand...
Click to collapse
Awesome bro. I will see if I have time to make the jig, if not i will just order it.
Also, is there any way to flash/root without DL mode or USB debugging or using Keis? My recovery mode works but that's all. Was wondering if there was a way i could flash/root from the 'apply update from sdcard' option in the recovery mode?
Seems like a driver error have u tried one of the heimdall one clicks http://forum.xda-developers.com/showthread.php?t=1358498
They will put u back to stock with a modified rooted kernel .
If anything try and manually point to the drivers in device manager. Or download android sdk and use the google drivers ?
rangergiya said:
Also, is there any way to flash/root without DL mode or USB debugging or using Keis? My recovery mode works but that's all. Was wondering if there was a way i could flash/root from the 'apply update from sdcard' option in the recovery mode?
Click to expand...
Click to collapse
There was with Froyo but with GB it's all been put into the kernel. So not that I'm aware of. However one of the GB leaks changed the key mapping of the phone. I forget which one but that might be the issue. Go to settings>about phone>build number and let me know what that says. post the base band as well.
hechoen said:
There was with Froyo but with GB it's all been put into the kernel. So not that I'm aware of. However one of the GB leaks changed the key mapping of the phone. I forget which one but that might be the issue. Go to settings>about phone>build number and let me know what that says. post the base band as well.
Click to expand...
Click to collapse
As requested,
Build number: GINGERBREAD.VUVKJ6
Baseband version: T959VUVKJ6
Well that is the official GB release so now I officially have no idea why you can't get into DL mode. Get the jig and let me know if that works. Good luck.
hechoen said:
Well that is the official GB release so now I officially have no idea why you can't get into DL mode. Get the jig and let me know if that works. Good luck.
Click to expand...
Click to collapse
Will do. Thanks for ur help.
I downloaded the terminal emulator app and tried doing 'reboot download' but says 'operation not permitted,' any way to get around that? Or any other non-button or non-adb way to get into download mode? Other than the jig? Or is it possible to get su privileges on an unrooted device for the 'reboot' command to work in the terminal emulator app?
It's giving you "not permitted" because you don't have root. Have you tried Super One Click to root? If you can get SOC to root it you can use terminal to force DL mode.
If you haven't hears the link.
http://shortfuse.org/
DL 2.3.1. It should come with the android drivers as well. Worth a shot. If it doesn't work it doesn't damage the phone at all.
hechoen said:
It's giving you "not permitted" because you don't have root. Have you tried Super One Click to root? If you can get SOC to root it you can use terminal to force DL mode.
If you haven't hears the link.
http://shortfuse.org/
DL 2.3.1. It should come with the android drivers as well. Worth a shot. If it doesn't work it doesn't damage the phone at all.
Click to expand...
Click to collapse
Im trying it now but for SOC to work, i have to have the proper drivers to get my phone connected. Will see whether the drivers that come with SOC work for my phone.
No luck with the SOC 2.3.1 drivers. They r the same as the android-sdk drivers
Will try the jig. Hope it works.
Have you tried using this DRIVER SWEEPER to remove the drivers?
eollie said:
Have you tried using this DRIVER SWEEPER to remove the drivers?
Click to expand...
Click to collapse
And then what? I've tried to get the phone connected on multiple computers without any luck. Uninstall and reinstall didnt give me any results.
rangergiya said:
And then what? I've tried to get the phone connected on multiple computers without any luck. Uninstall and reinstall didnt give me any results.
Click to expand...
Click to collapse
Im sorry I am having mouse issues that deleted part of my response..
Sometimes a residual driver will not allow you to properly install the drivers. I had a LG driver from my old phone that was conflicting with Samsung driver.
Also this is a new root process. I do not know if it will work or not. But Hell its worth a try right?
http://forum.xda-developers.com/showthread.php?t=1652825&highlight=root
eollie said:
Im sorry I am having mouse issues that deleted part of my response..
Sometimes a residual driver will not allow you to properly install the drivers. I had a LG driver from my old phone that was conflicting with Samsung driver.
Also this is a new root process. I do not know if it will work or not. But Hell its worth a try right?
http://forum.xda-developers.com/showthread.php?t=1652825&highlight=root
Click to expand...
Click to collapse
Thanks for that link. I will try it out and give an update here.
rangergiya said:
No luck with the SOC 2.3.1 drivers. They r the same as the android-sdk drivers
Will try the jig. Hope it works.
Click to expand...
Click to collapse
Just to make sure you had usb debugging and allow non market apss both CHECKED right?

Bricked my phone help

Alright so recently.... i wanted to root my Samsung Galaxy S 4g i fount out about odin.... then i found out about connecting it with stock kernels. and thats exactly waht i did. i opened odin and put my phone into download mode and i put a stock kernel uploaded from a user(ChainFire).I used his CF-Root-XX_OXA_JVK-v2.4-CWM3RFS kernel and put it into my device when it said PASS i was glad it worked..... excpet every time i turn it on now it gets stuck on the Samsung Galaxy S 4G SCREEN. SUCKS I TRIED USING DIFFRENT KERNELS AND ALL BUT NOTHING. Man if there is someone out there who could help plz HELP My mom would be so frieked when she found out i briked my phone.
PHONE INFO:
Model: SGH-T959V
Firmware: 2.2.1
Baseband: T959VUVKD1
Kernel: 2.6.32.9
Build Number: FROYO.VUVKD1
Follow this guide to a tea. When it says do I need to flash bootloader you will select yes. This will get you on gingerbread.
http://forum.xda-developers.com/showthread.php?t=1470716
thnx for the reply i will try this out when i get my new usb cable... for some reason other cables that look exactly the same that i own dont connect to my computer. I mean they charge and all but are NO GOOD FOR MASS STORAGE, PHONE MEDIA,TO ENTER DOWNLOAD MODE, etc. only for charging.
ALSO when i plug in my android to the pc using this USB cable it says "USB DEVICE NOT RECOGNIZED"
any more help plz....... i know u guys are tired of helping people with this sort of stuff, but come on thats what this site is for
Alaryze said:
any more help plz....... i know u guys are tired of helping people with this sort of stuff, but come on thats what this site is for
Click to expand...
Click to collapse
Actually this site is for learning about all things android. Not holding peoples hands that screw there phones. There is a ton of info on this site to help you. Think of it like going to the library. Sometimes the librarians busy and you have to find things for yourself. Look for the search feature and start using it.
hechoen said:
Actually this site is for learning about all things android. Not holding peoples hands that screw there phones. There is a ton of info on this site to help you. Think of it like going to the library. Sometimes the librarians busy and you have to find things for yourself. Look for the search feature and start using it.
Click to expand...
Click to collapse
so does that mean u got nothing. okay then im off to the search bar ill be visiting back here though cause the search bar might lead back to this topic XD
Alaryze said:
so does that mean u got nothing. okay then im off to the search bar ill be visiting back here though cause the search bar might lead back to this topic XD
Click to expand...
Click to collapse
Follow this to return your phone back to stock:
[Heimdall][One-Click] The T959V Heimdall One-Click Collection [05/20/2012]
In order to get into Download Mode, hold Vol-Up and Vol-Down while inserting the USB cord that is already plugged into your computer.
Then just click "flash", then when it's done, go back into download mode, check "flash bootloaders" on the computer, then click flash again.
You should be back to factory stock now.
cpkelley94 said:
Follow this to return your phone back to stock:
[Heimdall][One-Click] The T959V Heimdall One-Click Collection [05/20/2012]
In order to get into Download Mode, hold Vol-Up and Vol-Down while inserting the USB cord that is already plugged into your computer.
Then just click "flash", then when it's done, go back into download mode, check "flash bootloaders" on the computer, then click flash again.
You should be back to factory stock now.
Click to expand...
Click to collapse
thnx alot man but anyone know abou the usb problem. also when the USB DOES connect and gets signal, the phone dont reboot or anything sometimes usb composite device dont even appear in the list of all devices
If you still can get into download mode on the phone then it doesn't matter. The drivers get installed during the one-click process, just follow the directions when they come up.
Sent from my SGH-T959V using xda app-developers app
cpkelley94 said:
If you still can get into download mode on the phone then it doesn't matter. The drivers get installed during the one-click process, just follow the directions when they come up.
Sent from my SGH-T959V using xda app-developers app
Click to expand...
Click to collapse
should it say ERROR Drivers not found before it says on the second line " installing drivers" on the heimdall screen?
samsung usb composite device dont appear, i get gadget serial. and yes i put list all devices
Alaryze said:
samsung usb composite device dont appear, i get gadget serial. and yes i put list all devices
Click to expand...
Click to collapse
Hmm...I've never seen that before. I'd ask someone with a little more experience than me.
So, instead of PM'ing me, lets keep the discussion here.
I would have chimed in, but I don't know crap about windows.
Sounds to me like a windows driver issue. If you plug your phone in and see something new in device manager, uninstall the drivers for that device. Rinse - wash - repeat, until you get "Unknown Device".
Then make sure you have the visual c++ redistributable (mentioned in the OP of the oneclick thread).
Then run the heimdall oneclick. It will ask to install the drivers. You may need to reboot the computer after installing the drivers for them to work properly.
If you still have problems, hopefully one of the windows nerds around here can help.
wow... ur saying this ir rare stuff.
man what have i done to my phone, maybe it is just a windows problem -_-
Alaryze said:
wow... ur saying this ir rare stuff.
man what have i done to my phone, maybe it is just a windows problem -_-
Click to expand...
Click to collapse
I don't think it's your phone. I think it's your computer.
bhundven said:
I don't think it's your phone. I think it's your computer.
Click to expand...
Click to collapse
yah then ill uninstall this unknown device that keeps popping up when i connect my phone, then ill install drivers from heindmall and restart my compu just like u said. lemme giv it a shot
alfrigt it says connected in heomdall looks like u just gotta unplug nd plug a couple of times even though in device manager it has a exclamation mark next to samsung usb composite device. so do i just flash now.....? then what i read the guide yes but its not workin for me. i really need a nother step by step (post by post) tutorial
flashed, runned zadig.... and in all devices i get gadget searial and samsung mobile modem (interface 0) this one was new
should i just give up now or is there actually a way to fix this .
Did you select other and find the other drivers listed?
eollie said:
Did you select other and find the other drivers listed?
Click to expand...
Click to collapse
how do u do that?

Categories

Resources