********* OFFICIAL FOR USE ONLY ON GINGERBREAD ***************
Special thanks to PaoloM70.
Personal Thanks to Andy, Mik_os, Franciscofranco, Ciaox, Noejn and all other devs.
AmonRA to flash it with the need to disable the verification of signatures.
Overclocking
Smartass
Smoothass
Cifs
Supports EXT4
+upstream to 2.6.35.13
+oc, interactive, smartass, smoothass, cifs, ext4
+governor added SavagedZen
+autogroup scheduler (the patch of 200 lines)
+ smoothass smartass with a capped rate (standby) to set minimum
V3 Kernel -Old kernel:
ADB Bugfix for device
Reconfigured various kernel parameters (For better power management, CPU profiles)
-Added for the inversion axes Sippola in the new touch screen driver.
-Simple-inserted I / O scheduler (sio)
-Included various other patches 5-6
-Removed references-debug (smaller kernels)
-Small fix to reduce the impact on the CPU more pressure on the display (you can check with Neocore first ... the difference came in 8-well 9fps now settles down to 2-3fps)
******Updated 25 July*********
Magazine-routine to increase the stability and overclocking performance, cameraflick is absent up to 729mhz
Touch-fix which decreases the occupation of the CPU when you press your finger on the display (should no longer have the lag that had the first version of V4 (I hope))
Magazines-and reinsert all the previous patches (66 patches in total)
Inserted by the kernel-2.6.36 backport of block, and mtd workque
Backport-inserted by the kernel 3.0rc6 and cpufreq of cpuidle
http://www.mediafire.com/?g8r37pzsr3ig21j
+same kernel but without the fix for employment cpu (maybe better in the scroll lag if you have one) **No touch fix kernel***
http://www.mediafire.com/?bed0ht9kcz0071c
******Updated 08 Aug*********
Touch V6 2.6.35.14
V5-like, but updated to version 2.6.35.14
-Added 2.6.36 kernel backported from the i2c
-Support Module tun.ko
-Vsync enabled
http://www.mediafire.com/?otpne0w1v8bhnp8
If you want to try the version NoTouch kernel
http://www.mediafire.com/?4wuiscjcu5xal58
After flashing, wipe cache and davlik.
If you have a2sd then run the following in terminal:
su
a2sd cachesd
The phone will reboot automatically.
Download Ringing with No fade :Now supports Gingerbread 2.3.3 :
http://www.mediafire.com/?1xqcc0jppl2w9ic
Flash and enjoy
To know more the original idea, please visit the thread here :
Special Thanks to Januka for the idea.
For devs :
I/Paolo doesn't have a repository, So its uploaded here :
Kernel Ginger Source
http://d-h.st/jvn
u only need to change one line in Makefile
at line 193 change from
Code:
CROSS_COMPILE ?= /home/paolo/x-tools/arm-spica-linux-uclibcgnueabi/bin/arm-spica-linux-uclibcgnueabi- #CROSS_COMPILE ?= arm-eabi-
to
Code:
#CROSS_COMPILE ?= /home/paolo/x-tools/arm-spica-linux-uclibcgnueabi/bin/arm-spica-linux-uclibcgnueabi- CROSS_COMPILE ?= arm-eabi-
Yes, I know I should use search, but please, can anyone explain to me how do smartass and smoothass work in comparison to, for example, conservative and ondemand?
And massive thanks to you mansirawat!
If you already know that you should use the search function, maybe you don't know HOW to use it...
Here's a "tutorial": http://lmgtfy.com/?q=android+governors
Otherwise, you're just plain lazy... which one is it?
Ciaox should see this thread , he is waiting for GB OC Kernel
P.S : Thank you for the Kernel
Otherwise, you prefer wasting perfectly good post space in order to lecture me. Just like half the members of XDA. And the fact that you supposedly come from Romania as well just shows...nah, why bring that up here, all foreigners know it already.
Great! Awesome! Pure awesome!
Thanks a lot!
Stock rooted GB with this kernel (652/320)-> 1152 in quadrant. I don't care too much about those points, but my phone is smoother.
Working fine with void forever...yeah its smooth ...got 2020 in quadrant at 806 MHz
Sent from my LG-P500 using XDA App
do i have to flash a new baseband before flashing this on any custom rom? thanks
Flashed it,let's see!
Thanks!
Best!
Great!
Awesome!
Pure awesome!
mansirawat said:
********* OFFICIAL FOR USE ONLY ON GINGERBREAD ***************
Special thanks to PaoloM70.
Overclocking
Smartass
Smoothass
Cifs
Doesn't support EXT4
Click to expand...
Click to collapse
Hey mansi hows the performance??? If its good then it will be included in my new ROM.
CWM can also be used to flash this zip. Tested(CWM 3.1.0.0) and worked.
sajjan said:
Working fine with void forever...yeah its smooth ...got 2020 in quadrant at 806 MHz
Sent from my LG-P500 using XDA App
Click to expand...
Click to collapse
Why would you use this on a custom rom? We have Francisco's kernels for that.
devlin2427 said:
Why would you use this on a custom rom? We have Francisco's kernels for that.
Click to expand...
Click to collapse
its because krant,andy,mik's kernel are made of CM7 sources LG's are diff.
If you flash franco's kernel it will mk ur phone choppy. but you can try. if francos doesn't work you can flash this.....
Well I tried it out of curiousity ....and if not better it's definitely at par.....I still have to check battery life....
Sent from my LG-P500 using XDA App
cyber_avijit said:
its because krant,andy,mik's kernel are made of CM7 sources LG's are diff.
If you flash franco's kernel it will mk ur phone choppy. but you can try. if francos doesn't work you can flash this.....
Click to expand...
Click to collapse
does this kernel require a new baseband?thanks
roi14 said:
does this kernel require a new baseband?thanks
Click to expand...
Click to collapse
Yes, of course.
cyber_avijit said:
its because krant,andy,mik's kernel are made of CM7 sources LG's are diff.
If you flash franco's kernel it will mk ur phone choppy. but you can try. if francos doesn't work you can flash this.....
Click to expand...
Click to collapse
I'm afraid you didn't understand my question. I was asking why would he flash this kernel instead of Francisco's on void#forever.
devlin2427 said:
I'm afraid you didn't understand my question. I was asking why would he flash this kernel instead of Francisco's on void#forever.
Click to expand...
Click to collapse
ya you can use franco's kernel on any custom ROM other then those which are built from official 2.3.3
doktornotor said:
Yes, of course.
Click to expand...
Click to collapse
No. kernels have nothing to do with baseband. I flashed on v20g and its improved performance and another guy flashed on void forever and it improved performance.
Related
Kernel 2.6.29 (OC + UV patched)
8 MB Ram Hack
CFQ Scheduler
Pershoot's audiomod (loudness).
EXT4
tunnel module (automaticaly loaded on boot)
cifs + nfs module
Apply with recovery console.
There are 2 versions . (MCR and CM, If you have a Stock rom use the MCR version)
uvoc_v14 and oc_v14:
patched with UV-OC values up to 1267MHz.
8 Mb Ram Hack
CFQ scheduler
Audio-mod and some minor config changes.
setcpu.txt in package.
You need setcpu + the setcpu.txt for the OC kernels (copy it to the root of your sdcard) and choose "Custom Frequencies" in setcpu.
Please don't use setcpu's active widget (battery drain)
Dropped the auto-detection because of a contrast bug.
If you need other modules let me know.
Credits go to:
coolbho3000 for providing the oc-uv patches.
Version history:
V14 (oc and uvoc version):
compiler optimizations (-mcpu=cortex-a8 -march=armv7-a -mtune=cortex-a8 -mfpu=vfpv3 -O3 -Os)
Special Overclock only version
Audio-mod values lowered (some people reported echo)
uvoc_V13:
8 MB Ram Hack (thanks to coolbho3000)
uvoc_v12:
Pershoot's audio-mod values added
There is now an Overclock only update available (apply after one of the uvoc_v12 versions)
uvoc_V11:
Reverted to V7 config with just CFQ added.
No setcpu install means stock 245-998 Mhz (undervolted by 50 mV on all frequencies)
Only max-frequency 1267 MHz is running at stock 1300mV. (1113 MHz at 1275mV)
Special CM version available.
uvoc_V10:
changed CPU_FREQ_ONDEMAND_MIN to 245000.
Some minor tweaks.
uvoc_V9:
Change to voltages.
if you don't use setcpu stock frequency = 998MHz
CPU_FREQ_ONDEMAND_MIN = 128800
uvoc_V8:
CFQ standard scheduler
Included setcpu.txt with max 1113 MHz (if you want more edit setcpu.txt)
Some other kernel optimalisations based on Paul and Teknologist config.
uvoc_V7 :
switched the kernel modules tun.ko and cifs.ko because of a bug.
uvoc_V1-V6:
Lots of testing going on.
how to flash it? apply zip file from sd card in recovery, right?
Thanks! it boots..
fstluxe said:
This Kernel Doesn't Boot!
Click to expand...
Click to collapse
Tested on MCR (3) and using it with apps2sd + dalvik-cache on ext4
fstluxe said:
This Kernel Doesn't Boot!
Click to expand...
Click to collapse
booted for me
fstluxe said:
This Kernel Doesn't Boot!
Click to expand...
Click to collapse
What rom is on your device? I'm very sure the kernel can't be the problem. Just a different ramdisk maybe. I can make one specific for your rom.
Nice Kernel
Any chance to put in oc and uv?
richardtrip said:
What rom is on your device? I'm very sure the kernel can't be the problem. Just a different ramdisk maybe. I can make one specific for your rom.
Click to expand...
Click to collapse
The stock 1.5xx rom
sorry if this is a "noob" question but what exactly does this do?
fstluxe said:
The stock 1.5xx rom
Click to expand...
Click to collapse
Try attached zip. No automatic tun module loading (the stock boot ramdisk doesn't start init scripts).
bananapie said:
sorry if this is a "noob" question but what exactly does this do?
Click to expand...
Click to collapse
The update replaces the stock kernel and put some extra modules in /system/lib/modules. The compiled kernel does include some extra options (ext4,tun,cifs and a different scheduler named "The Brain F*ck Scheduler")
DocRambone said:
Nice Kernel
Any chance to put in oc and uv?
Click to expand...
Click to collapse
Yes, tested already, but i can't see the max above stock 998MHz in setcpu, so don't know if it's working. Used the same patch as coolbho3000 (http://forum.xda-developers.com/showthread.php?t=681733).
hmm are there Anny possibility's to use this with the stock rom because the stock rom is for me the most stable..
Edit : sorry i see a second file for the stock
richardtrip said:
Yes, tested already, but i can't see the max above stock 998MHz in setcpu, so don't know if it's working. Used the same patch as coolbho3000 (http://forum.xda-developers.com/showthread.php?t=681733).
Click to expand...
Click to collapse
Maybe we can use UV without OC for starters?
Hi i see you have test a own compiled version of your kernel with the acpulock patch of coolbho3000 .Can you maybe upload that Binary ? for us to test.
isn't it helping if you try to use the setcpu.txt and add there the OC LINES LIKE 1036800,1075200,1113600
richardtrip said:
Yes, tested already, but i can't see the max above stock 998MHz in setcpu, so don't know if it's working. Used the same patch as coolbho3000 (http://forum.xda-developers.com/showthread.php?t=681733).
Click to expand...
Click to collapse
Can you put up the CM version again?
fstluxe said:
Hi i see you have test a own compiled version of your kernel with the acpulock patch of coolbho3000 .Can you maybe upload that Binary ? for us to test.
isn't it helping if you try to use the setcpu.txt and add there the OC LINES LIKE 1036800,1075200,1113600
Click to expand...
Click to collapse
Tried that, but it didn't change anything (i can select higher, but it never goes above 998).
Hmm thats strange .. can this be caused by the bootloader
richardtrip said:
Tried that, but it didn't change anything (i can select higher, but it never goes above 998).
Click to expand...
Click to collapse
fstluxe said:
Hmm thats strange .. can this be caused by the bootloader
Click to expand...
Click to collapse
Check the first post (oc-uv is stable on my phone, but no better linpack-score's)
stingerpl said:
Maybe we can use UV without OC for starters?
Click to expand...
Click to collapse
ocuv version in first post.
First, i want to say thanks to:
Fserve, Hephappy, PaoloM70, Roqu3, doixanh : For every things. All credits give to you guy, specially is Fserve, Thank you Gerson !
af974, YZ: Thanks for being good Moderators for XDA Forum
Cyanogenmod Team, Code Aurora Forum: Special Thanks for sharing their kernel source with a lot of patches! .
Tasssadar: For many advices .
DJNoxD: Big Thank for helping me and to fix errors
alezardstar, Aspee, RockR172, Andy572: Big thanks for helping me a lot
Der_Caveman, Mik_os, Franco Francisco, selphien and.... sorry i can't remember all people, Thanks for sharing and advising!
All XDA "GOOD" Members .
Click to expand...
Click to collapse
Bassiclly Features:
Based on "gingerbread_rel" branch from Code Aurora Forum, merged into CM7 official kernel source. Thanks to Hephappy for doing this .
Backported stuffs from 3.0 kernel to make this kernel run on ICS ROM - All Credits to LGICS Team.
Updated kernel version from 2.6.35.10 to 2.6.35.14 with Power Management patches for better battery life.
Completly Fair Scheduler with Autogroup feature.
Overclocking support. CPU Frequencies that added: from 652Mhz - 806Mhz.
- Tip: Most of P500 can overclock to 729Mhz, becareful with higher frequencies.
Implemented SmartassV2 Governor with optimizations. Use as default governor.
Implemented optimized touch screen driver with multi-touching hack and High CPU Usage bug workaround (CPU Usage goes high when you touch the screen).
- Thanks to Der_Caveman for rewriting a better touch screen driver, waleedq and sippolo for implementing Axis Inversion hack, fserve for High CPU Usage bug fixes.
Camera Flickering fix
Tons of patches/tweaks from CAF, Cyanogenmod, me, many other people... All credits to them!
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Bugs:
Enabling GPS will bring "GPS wakelock". This will prevent your phone from going to deep sleep
Fix: Reboot your phone after enable GPS.
Random Rebooting... Nothing to say!
Click to expand...
Click to collapse
Reporting bugs:
Provide logcat when report bugs!
Click to expand...
Click to collapse
How to install:
Install the Kernel:
Reboot to Recovery.
Backup all thing FIRST!
Choose the caf-p500-xxxxxxxx-xxxx.zip (xxxxxxxx-xxxx is the kernel version)
Done it right? Reboot the system and Enjoy.
Click to expand...
Click to collapse
Tricks/Tips for getting better battery life:
Use the default governor - smartassv2! Highly Recommend!
Don't use CPU Profiles, SmartassV2 already has that.
Don't over clock your phone to higher than 729Mhz.
Click to expand...
Click to collapse
Kernel Download:
Please look into the 3rd post
Click to expand...
Click to collapse
Source:
Kernel Source Link (for ics only):https://github.com/thachtunganh/caf-kernel
Click to expand...
Click to collapse
Changelog
Changelog:
02/12/2012:
- Get up-to-date with Genet ICS kernel:
Remove obsolete audio pmem & increase PMEM_ADSP size.
Upgrade frame buffer to 3.0 kernel
Backport adsp_video_verify from .38 kernel
Update ashmem to msm-3.4
Full changelog: https://github.com/thachtunganh/caf-kernel/compare/b9810925f6...37cae19423
18/11/2012:
- Enable UID_STAT.
AngryWolf80 said:
Is it possible to enable uid_stat in this kernel?
This stuff activates per application traffic counter. Very useful thing with expensive mobile internet...
Click to expand...
Click to collapse
. Well, thank you for the tip
- Apply some PM patches, hope those patches can improve battery life
- Use XZ compression to compress kernel image.
- Please notice this version is for testing!
09/10/2012:
- Compiled with lastest Android NDK (r8b - new 4.6.3 GCC for ICS and Jelly Bean). And now Wifi module size is reduced from about 3MB to ~400KB .
- TUN/TAP module now is built in kernel image . Well, get more free space on ICS and Jelly Bean is awesome
- Update to Kernel release 2.6.35.14. :victory: (But i haven't apply some Power Management (PM) patches yet).
- Add Snappy compression support to zram. (this patch is from Zeev Tarantov . With Snappy, Zram uses less CPU time and is thus more useful, thanks to him!)
- Patches from Rashed97 - Who brought Unofficial CM10 Build for our device :laugh:
Fix mdp4_overlay for MDPI devices.
Hack for CRT animations fix.
- disable GENTLE_FAIR_SLEEPERS Sleeper Fairness in CFS. (this patch is from securecrt - Who Developed HWA kernel for ICS. Disabling Gentle Fair Sleepers could improve UI responsiveness. Thanks to him, too !)
- Restored a missed patch, AND USB MASS STORAGE PROBLEM ON ICS ROM IS FIXED WITH THIS PATCH (this patch is from Hephappy. Thanks to him!)
20/08/2012: From alezardstar, post #1048 . Big thank to him!
- smartassv2: some optimization for the governor.
- Use original CPU Frequencies. - No More Undervolted CPU Frequencies!
- Compiled with lastest Android NDK (r8b - new 4.6.3 GCC for ICS and Jelly Bean).
20/07/2012:
- Disabled Vsync for scrolling smoothness.
- Various tweaks from me. (Undervolted CPU frequencies (Undervolt 1 level): 122, 245, 320, 480, 600 Mhz. Increase Vibration level (from 115 to 120)).
- p500: Fix proximity sensor (thanks cyrix.vs) (took from hephappy, thanks to cyrix.vs).
- qdsp5: Incall recording pcm driver (took from hephappy).
- Tune dirty_background_ratio and vm_dirty_ratio (nobodyAtall AKA nAa from Xperia X8, X10 Mini, X10 Mini Pro Mobile Phone developement)
- Revert "Backport memory manager (mm) from ics_chocolate" module_alloc fails when wireless module activated in AP mode (hephappy).
- Revert "bcm4325: disable wakeup irq when device sleeps". (me)
- cpufreq: smartass2: change DEFAULT_RAMP_UP_STEP. (me)
02/07/2012:
- Implement optimized touch screen driver by Der_Caveman (Big thank to Tasssadar).
- sched_fair tweaks for improving performance. (IHO from OV).
- bcm4325: Force powersave mode, disable wakeup irq when device sleeps (IHO from OV, Mik_os).
- add the Stochastic Fair Blue (SFB) network scheduler. (LorDClockaN).
- fix rpcrouter misspelling (css771).
- usb: gadget: Remove unsupported mtp & ptp functions (hephappy).
- Disabled Hardware Keyboard support.
28/06/2012:
- Fix Data Usage - Set mobile data limit funtion for ICS. (lupohirp)
- Fix battery stat for ICS. (lupohirp).
- Enable Zcache in kernel. (me)
- Some bluetooth patches (Peter Hurley, jhovold).
- ext4: check for zero length extent (tytso)
25/06/2012:
- Fix USB Mass Storage for ICS. (hephappy).
- Bluesleep: Fix Wakeup (Tasssadar).
- Split out 2 part: Kernel (Normal Users) and Extra Modules (Extra For VPN, Tethering Users).
17/06/2012:
- Updated KGSL drivers (mikegapinski).
- Added frontswap, zCache, Cleancache; updated zRam. (lupohirp).
- Added Genlock (mikegapinski).
- Updated vidc/camera headers for compatibility (mikegapinski).
- Backport Memory Manager (mm) from Code Aurora Forum kernel, ics_chocolate branch (hephappy).
- Backport binder from 3.0rc6 kernel (Drew Walton)
- msm_fb : Add support for Yamato format (our adreno200 gpu) (lupohirp).
- Updated VFP code (lupohirp).
- Update network interface (adfad6666).
- cpufreq: backport cpufreq code from 3.0rc6 kernel (me).
- USB: f_mass_storage: Disable write cache support (Chiranjeevi Velempati).
- Many sched, autogroup patches (Mike Galbraith)
Click to expand...
Click to collapse
Download Section:
CAF Kernel (For ICS ONLY):
Kernel:
ALL VERSION include the lastest one: http://www.mediafire.com/caf-p500-kernel
Click to expand...
Click to collapse
Old Kernel LIKE ta-gb, thunderVN (For Gingerbread ONLY)
http://www.mediafire.com/?22y45z15xr2jv
Click to expand...
Click to collapse
FINALLY!! Was waiting for this!
To the testers please give the feedbacks
Sent from my LG-P500 using XDA App
I've been waitin' for like 5hrs??
Dowloadin'..
Sent from my LG-P500 using Tapatalk
Waiting for it.....FINALLY it's here thanx.
Thach!!!
Have you undervolted higher frequencies or just till 748?? 0_o
RockR172 said:
Have you undervolted higher frequencies or just till 748?? 0_o
Click to expand...
Click to collapse
No, description says undervolted low frq from 122-480
Shalu said:
No, description says undervolted low frq from 122-480
Click to expand...
Click to collapse
His previous version had 748 undervolted... m running it right now @748 without any random reboots which my phone used to get earlier @ that frequency...
Wait, il flash it n test...
Hey Thach, got a small problem camera exposure not working in cm nightlies#14 where It works fine on stock gb!
Shalu said:
Hey Thach, got a small problem camera exposure not working in cm nightlies#14 where It works fine on stock gb!
Click to expand...
Click to collapse
Camera Exposure , i don't know what is it? even i heard about it in Adfad6666 CM7 ROM
Rom Nightly Exposure in camera not working....no bug kernel
thachtunganh said:
Camera Exposure , i don't know what is it? even i heard about it in Adfad6666 CM7 ROM
Click to expand...
Click to collapse
It's also not working with Stock Cm7 kernel may be it's the problem in rom so chill
okay confirmed problem is in ROM
is it a .35 kernal or .32??
gurpreet9080 said:
is it a .35 kernal or .32??
Click to expand...
Click to collapse
It's a .35 kernel..
Oppss mistakenly pressed thankss,
Sent from my LG-P500 using Tapatalk
RockR172 said:
Have you undervolted higher frequencies or just till 748?? 0_o
Click to expand...
Click to collapse
Hey.. can u tell me what undervolting exactly does??
Sent from my LG-P500 using xda premium
fundoozzz said:
Hey.. can u tell me what undervolting exactly does??
Sent from my LG-P500 using xda premium
Click to expand...
Click to collapse
Less power on device, better battery.
But lower performance I think.
And why differs this kernel from Franco, like the ICS kernel? I think we already got enough kernels
Greets!
Shalu said:
It's also not working with Stock Cm7 kernel may be it's the problem in rom so chill
okay confirmed problem is in ROM
Click to expand...
Click to collapse
Oh, you mean the camera exposure , it's the camera flicker right?
If it right , it is the OC method , i use SoC OC method from cyangogenmod source.
The flicker fixed long time ago, i will fix it when i release the ICS kernel
fundoozzz said:
Hey.. can u tell me what undervolting exactly does??
Sent from my LG-P500 using xda premium
Click to expand...
Click to collapse
Undervolt will under the voltage of CPU Frequencies , it'll give you bettery battery life and stablity. And about the undervolt 748Mhz freq , i didn't do that.... I didn't test to undervolt 600Mhz and higher frequencies... doixanh (i took the undervolt frequencies from him) told me that it will crash when i undervolt 600Mhz and higher frequencies
Undervolt just decrease stability and only increase battery life by a bit.
[kernel][3.0.46][ics] •∞ CYMBALINE •∞ RD04 •∞ 2.8 •∞ [16-OCT-2012]
PLEASE READ THE ENTIRE POST #1 and POST #2, UNDERSTAND, READ IT AGAIN, BEFORE YOU DECIDE TO FLASH.
* THIS KERNEL IS ONLY FOR ICS (Android 4.0.x) TouchWiz (Samsung/ATT ICS releases, i.e any UCLF6, UCLF5, UXLF3, UCLD2, UCALC2) ROMS. It is NOT for after market ROMS like CyanogenMod or AOKP.
* The ONLY device that it has been tested is ATT SGH-I727 and Rogers SGH-I727R.
* CYMBALINE 2.X is a complete overhaul from 1.X series, if you have been using 1.X series, I would strongly recommend to upgrade to 2.X series.
Click to expand...
Click to collapse
DISCLAIMER
Click to expand...
Click to collapse
KERNEL FLASHING, OVERCLOCKING, UNDERVOLTING, ETC CAN POTENTIALLY DAMAGE YOUR PHONE. YOU ARE SOLELY RESPONSIBLE FOR FLASHING THIS KERNEL.
TUNING SCRIPTS
Click to expand...
Click to collapse
For Gov/OC/UV/UC tuning scripts for various governors. If you don't like to use an app (as lot of them cannot do fine grained tuning) you would like to use init scripts, then please see @ReedX50v scripts in this thread. The only requirement is "busybox run-parts init.d supports", most custom ROM's with modified Ramdisk kernel image should have that built-in. If it not, then bang your ROM author to provide one.
* For Cymbaline 2.6 and above (any ramdisk version, i.e. any of the RDNN) use the information in following post #574. You might also read the post #249, for some background information. Please thanks ReedX50v.
* For Cymbaline 2.5 and BELOW (any ramdisk version). use the scripts (again thank Reed50Xv). Use the scripts from the following post #249.
FEATURES/CHANGELOG
Click to expand...
Click to collapse
You can use 3rd Party APPS for CPU and Voltage Control. For Voltage, it is using the Faux VDD tables, so the app MUST be able to understand that. (See ADDONS section below).
[RD04][2.8]
updated to linux 3.0.46 upstream.
Experimental, ported CM10 bln with blink support (updates your lights lib in ROM). Not sure how great this is but feedback is appreciated.
WiFi sensitivity restored to stock.
[RD04][2.7]
updated to linux 3.0.42 upstream.
Ramdisk updated to support boot sounds. (remove /system/etc/PowerOn.ogg if you don't want it)
merged to latest (09/09/2012) CAF relevant changes.
[RD03][2.6]
Changed Ramdisk (def. governor changed from "ondemand_sammy" to "ondemand".
updated to linux 3.0.40 upstream.
updated WiFi stack to 1.15.55
Skipped internal releases 2.4 and 2.5.
FIX: Now overclock should be fully supported.
[RD02][2.3] Minor release, only one version now. Hacked to ensure that the max. boot ramp up is only 1.566GHz. If your phone can't handle that, sorry return it .
Added two more governors as modules : "savagedzen" and "hotplug"
Unified release, hack in place to not ramp up to the MAX allowed i.e. (1.836Ghz) so all phones should boot, as the boot max is set to 1.566GHz.
merged some bt code from Cymbaline 1.5 branch.
[RD02-2.2] Please note RAMDISK change, see below
Samsung ondemand governor moved as "ondemand_sammy", did this so that I can merge the standard ondemand and mods w/o creating a merge headache. Due, to this, the SAMMY settings in the RAMDISK modified to reflect the new name.
using linux ondemand with faux mods. (thanks faux123)
added faux's intellidemand as a built-in gov, since I like it (thanks faux123).
reverted the wi-fi optimization, which was causing tethering issues. (hopefully this is fixed)
pre-emptive strike: merged all Govs from 1.5. Please don't complain that I am missing one. As usual all these are in /system/lib/modules. so you would need to "insmod" (see ReedX50v scripts for samples). Here is the remaining ones (please see RD01-2.1 ChangeLog for others)
Code:
/system/lib/modules/cpufreq_brazilianwax.ko
/system/lib/modules/cpufreq_lionheart.ko
/system/lib/modules/cpufreq_lulzactive.ko
/system/lib/modules/cpufreq_ondemandx.ko
/system/lib/modules/cpufreq_wheatley.ko
[RD01-2.1]
BLN Fix: reverted 2.0 changes, should work now
Providing two CWM flashable zips. One OC to 1.8366GHz and another with OC Capped at 1.566GHz.
Upped the voltage to 1350mV as per ReedX50v testing results and recommendation (hit his thanks button).
IMPORTANT: ALL CUSTOM GOVERNORS are compiled a Kernel Modules. Please use init script to enable the ones you want. I have done this so as to eliminate any interference from them.
This version has the following Governors: (Please see Post #420)
Code:
/system/lib/modules/cpufreq_adaptive.ko
/system/lib/modules/cpufreq_badass.ko
/system/lib/modules/cpufreq_lagfree.ko
/system/lib/modules/cpufreq_lazy.ko
/system/lib/modules/cpufreq_pegasusq.ko
/system/lib/modules/cpufreq_smartass2.ko
[RD01-2.0] Major version change. REMOVED SOME GOVERNORS, please restore to stock ondemand before flashing (i.e. disable init scripts or apply on boot settings in whatever app you are using).
Updated to upstream Kernel 3.0.38
Bunch of NetFilter kernel modules in /system/lib/modules for the interested users.
I have removed some governors, please reset to default governor "ondemand", before flashing.
cherry-picked key changes from CAF.
GPU OC (NOTE: please use sysfs interface to change the frequency the default is stock values, see post #2)
3D Mode: 320000000, 300000000, 266667000, 228571000, 200000000, 177778000, 27000000
2D Mode: 266667000, 228571000, 200000000, 160000000, 96000000, 27000000
Cherry Picked various bits from Samsung Code released for our device.
CPU OC: 192KHz - 186300KHz.
Cleaned up BLN code.
Added some WiFi fixes.
This is mainly a release based of the major overhaul.
Added more I/O Schedulers: BFQ (v3r4), Simple I/O, VR.
[1.5] Please see the posts for the evolution of this version, the last post should detail the final changes (208) #151 , #161 and #208
[1.4] Scaled down the defaul ondemand governor to 1.566 (slight oc). Should perform really well for people satisfied with the defaults.
[1.4] Added more governors for people to play around with, note, I would like to trim it down in futures versions of cymbaline. The newly added ones are (thanks to whoever developed them):
brazilianwax
ondemandx
lionheart
SavagedZen
wheatley
scary
[1.4] Moved init.qcom.post_boot.sh into the ramdisk, to not depend on ROM variances. You should use the /system/etc/init.d hook (of course busybox must be installed).
[1.3] bugfix: the max. freq. was not enabled in 1.2, fixed in this release.
[1.3] some compiler tweaks added building this version of kernel.
[1.2] Restored settings to Stock Governor & I/O scheduler.(ondemand/cfq)
[1.2] BUGFIX: BLN and TouchKey backlight interactions for the "on" settings were conflicting. restored to UCLD2 behavior.
[1.1] Default Governor is tegraks lulzactive.
[1.1] Default CPU Scaling Max. is 1.566MHz.
[1.1] Available Governors (Most governors tuning via sysfs interface please google)
smartass V2
badass
lazy
intellidemand
lagfree
interactive
lulzactive (default)
[1.1] Using Faux's CPU and Voltage table
[1.1] Faux's GPU Overclock (not tunable from userspace)
[1.1] Max Overclockable Frequency: 1.728MHz
[1.0] BLN support.
[1.0] UTF-8 Support.
[1.0] Kernel symbols enabled (some apps require it)
[1.0] init.d: via busybox run-parts, place your scripts in /system/etc/init.d/ (chown root.shell) (chmod 755)
[1.0] insecure (ro.secure=0)
[1.0] adb root
[1.0] adb default shell bash.
[1.0] All IPV6 options enabled.
[1.0] CIFS is a kernel module (/lib/modules/cifs.ko)
[1.0] bootanimation support, drop your favorite bootanimation.zip in /system/media.
[0.0-0.6] Front Camera fully functional WITHOUT any lib hacks for Skyrocket ICS ROMS. Which means keep dont change the libs.
[0.0-0.6] Back Camera working.
[0.0-0.6] Completely removed MMC_ERASE capability, that means with the running kernel any erase to internal sdcard will error out. This is implemented as per the "brickbug" recommendation.
[0.0-0.6] General code merges and cleanup.
DOWNLOADS
Click to expand...
Click to collapse
Always, download the latest one, unless you have a need to be on a older version.
[16-OCT-2012] [RD04][2.8] Please read the changelog above.
CYMBALINE-RD04-2.8-cwm5.zip
[16-SEP-2012] [RD04][2.7] Please read the changelog.
CYMBALINE-RD04-2.7-FINAL-cwm5.zip
[12-AUG-2012] [RD03][2.6] Please read the changelog, this post again and post #2 again.
CYMBALINE-RD03-2.6-cwm5.zip
[09-AUG-2012] [RD01-2.3] Please read the changelog, this post again and post #2 again.
CYMBALINE-RD02-2.3-cwm5.zip
[07-AUG-2012] [RD01-2.2] Please read the Changelog and post #2. Again providing two versions, if the 1.8366GHz causes problem booting (e.g. bootloops) flash the 1.566GHz one..
CYMBALINE-RD02-2.2-cwm5-1.836GHz.zip
CYMBALINE-RD02-2.2-cwm5-1.566GHz.zip
[06-AUG-2012] [RD01-2.1] Two versions available for download. If your phone cannot handle the 1.8366GHz (bootloop) then flash the 1.566GHz version
CYMBALINE-RD01-2.1-cwm5-1.836GHz.zip
CYMBALINE-RD01-2.1-cwm5-1.566GHz.zip
[06-AUG-2012] [RD01-2.0] No Overclock version. That is max. CPU is capped at 1.512GHz, use this if you are having bootloops flashing the overclockable to 1.83GHz version. CYMBALINE-RD01-2.0-NO-OC-cwm5.zip (1.512GHz Max.).
[05-AUG-2012]: [RD01-2.0] CYMBALINE-RD01-2.0-cwm5.zip. Please see the change log. (Overclockable upto 1.836GHz).
[27-JUN-2012]: (3.0.8-1.5) CWM Flashable (TouchWiz based ROMS only). Download
[24-JUN-2012]: (3.0.8-1.4) CWM flashable. ICS ROMS (SAMSUNG TouchWiz based) ONLY. NOTE: THIS WILL REPLACE YOUR /system/lib/modules with a symlink to kernel modules (Please see revert section). (installation, just flash in CWM nothing else). CYMBALINE-1.4-cwm5.zip
REVERTS
Click to expand...
Click to collapse
[STOCK-UCLF6] (Official Samsung/ATT Stock Kernel). CWM5 flashable. kernel-sgh-i727-UCLF6-cwm5.zip
[STOCK-UCLE2]: CWM flashable. ATT SKYROCKET, ICS BUILDS ONLY. Download
KNOWN ISSUES/BUGS
Click to expand...
Click to collapse
None as of now.
ADD ON/APPS
Click to expand...
Click to collapse
As far as I know (not tried it), only SystemTuner provides the "lipstick" for reading the voltage table and allowing you granular control of the voltage for each frequency.
Most of the other apps, can I believe allow you to change the CPU/IO scheduler/Govs, safely.
Or, if you are hardcore, please see this post 249 by ReedX50v (hit his thanks button), for graciously providing flashable init scripts, you can use one as a template to what works for you.
SOURCE AND OTHER INFO
Click to expand...
Click to collapse
As per GPL requirements, I will post the source as soon as I have me repo setup. The current version is built straight from SAMSUNG Sources for the Korean SKYROCKET LTE. You can build it yourself from here:
Source Git Hub Repo: https://github.com/mohankr/android_kernel_samsung_msm8x60.git
CREDITS/THANKS
Click to expand...
Click to collapse
Although, there was a lot of effort involved in bringing this kernel, but without the following people doing the heavy lifting, it would not be possible..to bring it so quickly.
Faux123 (for majority of the heavy lifting) (gov, oc, uv and gpu). I just ported it over to our device kernel.
tegrak (lulzactive governors)
creams (bln)
romanbb (bln)
DaG (bln)
ReedX50v for providing flashable scripts.
samsung, for at least releasing the source for a similar device, so i could bring this..
whoever were the original authors for the governors included, that were not part of the source.
Click to expand...
Click to collapse
reserved
1) ROM Developers Info.
If you are planning to bundle this kernel in your ROM. The Samsung init.qcom.post_boot.sh has been disabled and moved to the ramdisk. Your changes should be incorporated in /system/etc/init.d scripts (of course need busybox installed). NOTE: the init scripts always execute after the above script, so you can always override the values there.
2) How do I find the available governors?
Below adb command, will tell you what the available governors in the kernel are (assumes adb/rooted) (shown in 1.4 kernel):
Code:
$ adb shell cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_governors
brazilianwax ondemandx SavagedZen wheatley scary smartassV2 badass lazy intellidemand lagfree lulzactive interactive conservative ondemand userspace powersave Lionheart performance
3) Sysfs interface for GPU OC?
The GPU OC Modes are supported:
Available frequencies:
Code:
3D: 320000000, 300000000, 266667000, 228571000, 200000000, 177778000, 27000000
2D: 266667000, 228571000, 200000000, 160000000, 96000000, 27000000
The default (and the default in CYMBALINE Version 2.0 and above) stock values are:
Code:
3D @266MHz and [email protected]
To change the values use the sysfs interface here are the relevant samples to max it all out. (you can make an init script to make it permanent)
Code:
#!/system/bin/sh
echo "Overclocking GPU"
echo 320000000 > /sys/devices/platform/kgsl-3d0.0/kgsl/kgsl-3d0/max_gpuclk
echo 266667000 > /sys/devices/platform/kgsl-2d0.0/kgsl/kgsl-2d0/max_gpuclk
echo 266667000 > /sys/devices/platform/kgsl-2d1.1/kgsl/kgsl-2d1/max_gpuclk
echo "End"
exit 0
4) Why does the CPUSpy show reaching max. CPU frequency, even though the bundled values 1.52GHz?
This is caused by SAMMY ROM ramping up the CPU's to the Max. during boot. I am looking for a clean way for this to not happen, once I find the source (I have few things narrowed down)...
This is really exciting! Read about this in your other thread and started to pitch a tent.
Bluetooth is not a deal breaker for me so let me know if you need a tester for camera.
Can test on whatever rom needed. Stock, etc.
Sent from my SAMSUNG-SGH-I727 using xda premium
Can't wait to download this when Bluetooth & camera are fixed.
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
Some more great work from you mohan. Have you been looking for any possible bln/overclock patches now that you have the source? I'm happy to help in any way I can.
jomeister15 said:
Some more great work from you mohan. Have you been looking for any possible bln/overclock patches now that you have the source? I'm happy to help in any way I can.
Click to expand...
Click to collapse
Thanks. Yes, those will be the first in the TODO list..Also, people have pointed to other interesting kernel mods (like siyah)..Once the source is up I am hoping it will spur involvement from everyone, that will be great..
BLN support?
raviluke said:
BLN support?
Click to expand...
Click to collapse
Umm, look up one post?
The cm9 and aokp guys are gonna love this.
Sent from my SAMSUNG-SGH-I727 using xda premium
if da_G or faux123 does their magic with the kernel for aokp/cm9 now that teh source is avail that would be lovely .
truly
Those guys are long gone..
Sent from my SAMSUNG-SGH-I727 using xda premium
Well, good thing folks like the OP are still around then...
Thought I was noticing a theme in your rom/kernel names and was going to ask if this (and Embryo) were named for Pink Floyd songs.
But then I thought I'd use Google before asking and I found your post stating that Embryo was in fact named as a dedication to the Pink Floyd song (here: http://forum.xda-developers.com/showpost.php?p=25925976&postcount=287 ).
Would love to see you do something -- anything -- with the song, "Several Species of Small Furry Animals Gathered Together in a Cave and Grooving with a Pict"
ReedX50v said:
Well, good thing folks like the OP are still around then...
Click to expand...
Click to collapse
Agreed
Sent from my SAMSUNG-SGH-I727 using xda premium
mindmajick said:
Those guys are long gone..
Sent from my SAMSUNG-SGH-I727 using xda premium
Click to expand...
Click to collapse
Da_g is gone, he got a g-note i believe? But i'm sure faux will make an ICS kernel once the official i727 kernel source is released.
T989 source is here.
http://opensource.samsung.com/reception/receptionSub.do?method=search&searchValue=SGH-T989
3rd one down.
Sent from my SAMSUNG-SGH-I727 using xda premium
Wow thanks, mohan you rock
mindmajick said:
T989 source is here.
http://opensource.samsung.com/reception/receptionSub.do?method=search&searchValue=SGH-T989
3rd one down.
Sent from my SAMSUNG-SGH-I727 using xda premium
Click to expand...
Click to collapse
Thanks..let's see if they left the the key bluetooth files..i got camera to work w/o preview..
EDIT: cool..the bits are there ..now to compile and boot..
oh crap I forgot about mohan . apologies
Nice. Nice. Nice. Nice. Nice.
Uc/UV here we come
sent from my I727 TROLLING DEVICE using XDA premium.
So I'm presenting my kernel today I didn't sleep because it was so fun to compile and compile all night so I make my own kernel and yesterday I made some questions and I need to thanks "_that" because he help me to compile the kernel.
Reloaded version done from Zero again will put the features missing later.
Now I will do extensive test of a version and will know exactly what changes from version to version.
I will start to add the featurer that were on my previous kernel later..
Features:
ISO 9660 Support
UDF Support
CIFS Support
Dynamic Fsync
No more crash when reading /sys/bus/nvhost/drivers/tegradc/tegradc.0/nvdps
Companion Core OC to it's full potential 620 MHz
Thalamus hot-plugging
Compiler With Linaro 4.7 using -O3 Optimizations
I/O Schedulers
noop
deadline
row - default
cfq
bfq
sio
CPU Governors:
lagfree
smartassH3
touchdemand
lulzactive
pegasusq
interactive - default
And the default ones.
Ramdisk:
DPI Unlocked
ADBD with Root (ro.secure=0 )
Coming next:
data2sd Support
CPU Overclock
GPU Overclock
Github:
https://github.com/maxrdlf95/tf700t_maxkernel
Source for V1
Comming
Source for V2
https://docs.google.com/file/d/0B0UY4U-rpxjsekI5TVp1SUNRNkU/edit?usp=sharing
Soon I will only include patch files to older versions as I will be using Github..
Changelog Reloaded:
V1
Made from zero
Dynamic Fsync
ROW Scheduler
Compiled with latest Linaro 2013.04
V2
Added Thalamus Hotplug
Added Voltage Control
Improved lowmemorykiller
Added Improved glibc, memcpy, memmove Functions
Optimized ARM RWSEM Algorithm
Added SmartAss H3 Governor
Added lagfree Governor More to come
Added Optimized CRC32 Algorithm
Added Optimized AES and SHA1 routines
V3
GPU Overclock 666 MHz
LP Core Overclock 620 MHz
V4
Add SIO scheduler
Add Touchdemand governor
Changes on TCP
Optimization of ondemand and interactive and CFQ
Optimization to code
BFQ & SIO are back
Improvements to I/O
Compiled now using O3 Flag
Fixed CIFS thanks to the guy that posted the patch here
Still working on GPU OC Issue and CPU OC
Some fixes
RC Release:
Updated to 10.6.1.14.8 Source code
Added CPU OC up to 1.9 GHz Please use Trickster or Franco.app latest version which works fine
Some updates to ext3 and ext4 filesystem
Lots of changes to come yet tomorrow will do more work
Credits:
Ezekeel, faux123, _that, Metallice, David McCullough & lupohirp
Thanks:
buhohitr So much for checking all test version of kernel I send and help me to fix this
wingdo For testing some kernel versions also
Changelog Old Version:
V1
First version
Lot of optimizations and patches that I don't remember now.
V2
init.d Support
Linaro 4.7 2013.03 Compiled
Updates to lowmemorykiller
Some changes in governors
V2.1
Fixed Clocks Speed
Fixed Companion Core Overclock
GPU Overclock 666 MHz
V3
Optimizations to EXT4 Filesystem
Added improved version of glibc, memcpy & memmove
Added optimized AES and SHA1
Added support to hardboot to a kexec kernel
Some fixed in code of Thalamus Hotplug
More things that I don't remember
V4
Removed some unnecesary code
Added Dynamic Fsync
Fixed Reboot issues
Some other things I don't remember, so busy now..
First!
maxrdlf95 said:
So I'm presenting my kernel today I didn't sleep because it was so fun to compile and compile all night so I make my own kernel
Click to expand...
Click to collapse
Cool, another kernel. :good: I think I can retire soon.
maxrdlf95 said:
Lot of optimizations and patches that I don't remember now.
Click to expand...
Click to collapse
Remember you have to offer the source code of your kernel because it's under GPL license.
_that said:
First!
Cool, another kernel. :good: I think I can retire soon.
Remember you have to offer the source code of your kernel because it's under GPL license.
Click to expand...
Click to collapse
Oh yes.. Will upload it tonight untill I learn how to use github
P.D Don't retire yet I'm still learning
Cool
That´s great news, thanks! Downloading now...
maxrdlf95 said:
Oh yes.. Will upload it tonight untill I learn how to use github
Click to expand...
Click to collapse
Ah, github ... it's great, but I will only start using it when I know how to use it correctly.
maxrdlf95 said:
P.D Don't retire yet I'm still learning
Click to expand...
Click to collapse
That was, of course, a joke - I will continue to maintain my stable stock kernel, presumably as long as I own the device, maybe even a bit longer. It's great that we now have multiple devs who bring variety.
great to see that someone else is finally seeing the potential of thalamus' hotplugging routines.
Which ones are you using (modified from franco or the original ones)?
Good to see another dev!
bryce09 said:
great to see that someone else is finally seeing the potential of thalamus' hotplugging routines.
Click to expand...
Click to collapse
Do you understand how hotplugging works together with the lp/g cluster switching? And well enough that you can explain it to me?
maxrdlf95 said:
Oh yes.. Will upload it tonight untill I learn how to use github
P.D Don't retire yet I'm still learning
Click to expand...
Click to collapse
With the fortune _That made from publishing his kernels and giving good advices to everyone in this community, he can sure retire from his regular work and help us more here..
bryce09 said:
great to see that someone else is finally seeing the potential of thalamus' hotplugging routines.
Which ones are you using (modified from franco or the original ones)?
Good to see another dev!
Click to expand...
Click to collapse
Im using original Thalamus THanks!:good:
So I got already init.d Support wil upload next version with that and kexec suport for mutiboot
Source code will also be with that version
Is it possible you're going to release a version for data2sd like Hund's kernel? That would be great. Thanks.
With quadrant your kernel is about 150point more than that V2 stock kernel and it's flying when I put on performance mode (as fast as Hund's OC kernel). I ran about 10 quadrant and the cpu temp is about 42C. Good job for your first time!!
Edit: I set the governor to lagfree and balance mode, pretty smooth and fast, very nice for daily driver, but once I set it on performance mode this thing is flying...kid you not!
buhohitr said:
Is it possible you're going to release a version for data2sd like Hund's kernel? That would be great. Thanks.
Click to expand...
Click to collapse
Yes I can do that
Next version will be Linaro 4.7 2013.03 Compiled so if should fly!
So far, this kernel (V1) is running really smooth with interactive and SIO. I tweaked interactive a bit to improve battery.
I noticed minimum freq never drops under 513 MHz and there is hotplug tuning vs just "max active cores" like in stock.
Questions:
Why minimum freq at 513?
Is there a way to tune hotplug to only use 2 cores?
When flashing V2 over V1, should I wipe cache and dalvik?
I'd love to know, and appreciate you guys helping me learn more about kernels and settings (I don't mean for the questions to be demanding or rude, I just wanted to ask in a straightforward manner, right to the point).
Greatly appreciate your work, flashing V2 now!!
Sent from my ASUS Transformer Pad TF700T using xda app-developers app
uberbania said:
So far, this kernel (V1) is running really smooth with interactive and SIO. I tweaked interactive a bit to improve battery.
I noticed minimum freq never drops under 513 MHz and there is hotplug tuning vs just "max active cores" like in stock.
Questions:
Why minimum freq at 513?
Is there a way to tune hotplug to only use 2 cores?
When flashing V2 over V1, should I wipe cache and dalvik?
I'd love to know, and appreciate you guys helping me learn more about kernels and settings (I don't mean for the questions to be demanding or rude, I just wanted to ask in a straightforward manner, right to the point).
Greatly appreciate your work, flashing V2 now!!
Sent from my ASUS Transformer Pad TF700T using xda app-developers app
Click to expand...
Click to collapse
1 I think I know why minimun its at 513 will check that later
How that of tuning to use 2 cores only
Hotplug turn on/off CPUs automatically based on frequency..
V2 over V1 no you will be ok just flashing on top of it
Always good to see another kernel for our infinity :good: Just wondering what everyone's experience with battery life has been compared to stock or that's kernel?
Great work! Are you on with me to include in CROMi-X? :cyclops:
sbdags said:
Great work! Are you on with me to include in CROMi-X? :cyclops:
Click to expand...
Click to collapse
Yes Im with you no problem to include let me fix the Clocks and you can use V3
Thanks! :highfive:
Max, I have a question, is it possible to make the powersaver/balance/performance mode stick after a reboot by just using the UI?
Edit: Also your kernel is only using the following frequencies: 1700, 1600, 1000, 620, 513 and deep sleep.
buhohitr said:
Max, I have a question, is it possible to make the powersaver/balance/performance mode stick after a reboot by just using the UI?
Edit: Also your kernel is only using the following frequencies: 1700, 1600, 1000, 620, 513 and deep sleep.
Click to expand...
Click to collapse
There was an error on frequency table I fixed it already and now min its 475 again
workes only on OMNI based Roms.
This is a beta Kernel! Only test, if you know what you are doing!!
The battery stats with this Kernel and intelliplug on are awesome!!
Features:
-Intelli Plug integrated
-CPU Volt ajust integradet
-lots of scheduler and governors
-flip2wake/flip2sleep/doubletab2wake ...
Please try and give responce!!
ATENTION if you try my Kernel, you will flash a custom boot animation!!
Changelog:
--------AGK-OMNI Kernel 1.05--------
-fix CPU clocking
-add overclocking of slimbus
--------AGK-OMNI Kernel 1.04--------
-add more GPU OC/UC range
--------AGK-OMNI Kernel 1.03--------
add some governors:
-add wrexy governor
-add nightmare governor
-intellidemand
-intelliactive
-smartassV2
-badass
-lagfree
-integrate some modules in Kernel
-reduce install files size
-add new bootanimation
--------AGK-OMNI Kernel 1.02--------
-fix volt ajust
-add Cpu OC and UC
-change GPU max OC
-fix wifi problem
-add custom boot animation
known issues:
-?
--------AGK-OMNI Kernel 1.01--------
-add intelli plug
known issues:
- volt ajust doesnt work
- Cpu OC doesnt work
Click to expand...
Click to collapse
Downloads:
AGK-OMNIROM-Kernel-recovery-1.01.zip - 17.22 MB
AGK-OMNIROM-Kernel-recovery-1.02.zip - 10.05 MB
AGK-OMNIROM-Kernel-recovery-1.03.zip - 9.92 MB
AGK-OMNIROM-Kernel-recovery-1.04.zip - 9.92 MB
AGK-OMNIROM-Kernel-recovery-1.05.zip - 9.92 MB
Click to expand...
Click to collapse
Kernel Source: https://github.com/antaril/AGK-OMNI
This Kernel based on "Dirty Unicorns" Source
testing now ! ...
i can confirm that the battery stats are awesome on this kernel
however ... the best omni kernel !
edit: ATTENTION!!!
i do not recommend to use smartmax_eps governor for now, it seems that there is an bug which prevent the screen from turning on and reboots the device instead !
Sry for op, but intelliPlug is the best governor for battery stat?
dena994 said:
Sry for op, but intelliPlug is the best governor for battery stat?
Click to expand...
Click to collapse
intelli plug is an alternative hotplug. you can change it in tricksterMod! standard its always MPDecision! But i change this!! Try, its awesome!
Antaril said:
intelli plug is an alternative hotplug. you can change it in tricksterMod! standard its always MPDecision! But i change this!! Try, its awesome!
Click to expand...
Click to collapse
I'm looking ti have the best battery, so witch version of AGK should I install with paranoid?
dena994 said:
I'm looking ti have the best battery, so witch version of AGK should I install with paranoid?
Click to expand...
Click to collapse
paranoid is aosp. Please install the other Version!!
Antaril said:
paranoid is aosp. Please install the other Version!!
Click to expand...
Click to collapse
Yes, but I want to know what version gives the best battery life! Hotplug, exc
dena994 said:
Yes, but I want to know what version gives the best battery life! Hotplug, exc
Click to expand...
Click to collapse
for me its intelli plug!! SMartmax and deadline! vcore ajust- 0,5
Thanks
sorry to be that guy LOL, we need more kernels here specially AOSP, why limited this to OMNI only ? smh
TheUndertaker21 said:
sorry to be that guy LOL, we need more kernels here specially AOSP, why limited this to OMNI only ? smh
Click to expand...
Click to collapse
Check the original development thread. There is one from same developer for AOSP ROMs. The AOSP kernel works great as well!
Sent from my One using XDA Premium 4 mobile app
TheUndertaker21 said:
sorry to be that guy LOL, we need more kernels here specially AOSP, why limited this to OMNI only ? smh
Click to expand...
Click to collapse
look here: http://forum.xda-developers.com/showthread.php?t=2764555
Because omni is special!! Standart AOSP Kernel will not work correctly! But you can try to use this one in AOSP. I havent try this...
new Version online!! See on first thread
Antaril said:
look here: http://forum.xda-developers.com/showthread.php?t=2764555
Because omni is special!! Standart AOSP Kernel will not work correctly! But you can try to use this one in AOSP. I havent try this...
Click to expand...
Click to collapse
You linked me to a thread that hasn't been updated since may. That's not what I meant. I meant there aren't a lot of aosp kernels out there. But, whatever.
Sent from my HTC One using XDA Premium 4 mobile app
TheUndertaker21 said:
You linked me to a thread that hasn't been updated since may. That's not what I meant. I meant there aren't a lot of aosp kernels out there. But, whatever.
Sent from my HTC One using XDA Premium 4 mobile app
Click to expand...
Click to collapse
No thats wrong... first look here : "Old 27th May 2014, 02:28 PM (Last edited by Antaril; 1st July 2014 at 01:26 PM."
And if you read the thread name, you can read that :"[Kernel] [AOSP] [27.05.2014] AGK Kernel v1.16"
But you are right, there aren't a lot of AOSP Kernels, but i have made one! And there aren't also alot of OMNI Kernels out there! So?
Antaril said:
new Version online!! See on first thread
Click to expand...
Click to collapse
new version ?
you mean 1.04 ?
GPU OC max 487Mhz befor was 533Mhz ... is there a reason for lower OC ?
StalCaiRe said:
new version ?
you mean 1.04 ?
GPU OC max 487Mhz befor was 533Mhz ... is there a reason for lower OC ?
Click to expand...
Click to collapse
yes, it was too much oc. But now you have more range!!
please add bln in this kernel.thx
karmania said:
please add bln in this kernel.thx
Click to expand...
Click to collapse
bln should be inside!! Which Rom do you use? in Dirty Unicorns bln doesnt run!
i use omni rom with agk 1.04 kernel on htc one m7.but bln not work for me! what should i do?