Related
Can someone point me to where I can learn how to use set cpu and set voltage properly. Just installed superotimized kernel and wondering how to take full advantage of it
p4ranoid4ndroid said:
Can someone point me to where I can learn how to use set cpu and set voltage properly. Just installed superotimized kernel and wondering how to take full advantage of it
Click to expand...
Click to collapse
overclocking is pre-enabled, under volting can be done through an app the link is in the thread. there are 2 settings. try about -50v each if that works fine bump one down to -75mv at a time. test the phone over a day or two and see how it runs, see if it has sleep death after a few periods of inactivity, especially extended periods, see if it has sleep death while charging, which seems to make a difference that will test the low setting.
see if the phone shuts down without freezing, and see if it shuts down without freezing while charging, the heat in the battery makes a big difference, play some 3d games. if you have freezing issues you can disable overclocking under different situation with set cpu or se t the volts to a more conservative setting.
Dani897 said:
overclocking is pre-enabled, under volting can be done through an app the link is in the thread. there are 2 settings. try about -50v each if that works fine bump one down to -75mv at a time. test the phone over a day or two and see how it runs, see if it has sleep death after a few periods of inactivity, especially extended periods, see if it has sleep death while charging, which seems to make a difference that will test the low setting.
see if the phone shuts down without freezing, and see if it shuts down without freezing while charging, the heat in the battery makes a big difference, play some 3d games. if you have freezing issues you can disable overclocking under different situation with set cpu or se t the volts to a more conservative setting.
Click to expand...
Click to collapse
I've been told that undervolting can improve the battery time. Of course, lots of varying opinions of how good/bad it may be to overclock.
If I want to just undervolt, is that possible with SetCPU?
Dani897 said:
overclocking is pre-enabled, under volting can be done through an app the link is in the thread. there are 2 settings. try about -50v each if that works fine bump one down to -75mv at a time. test the phone over a day or two and see how it runs, see if it has sleep death after a few periods of inactivity, especially extended periods, see if it has sleep death while charging, which seems to make a difference that will test the low setting.
see if the phone shuts down without freezing, and see if it shuts down without freezing while charging, the heat in the battery makes a big difference, play some 3d games. if you have freezing issues you can disable overclocking under different situation with set cpu or se t the volts to a more conservative setting.
Click to expand...
Click to collapse
ewingr said:
I've been told that undervolting can improve the battery time. Of course, lots of varying opinions of how good/bad it may be to overclock.
If I want to just undervolt, is that possible with SetCPU?
Click to expand...
Click to collapse
Interesting stuff...
I too would like to know if it is possible to simply under-volt. Does anyone know the optimal settings for SetCpu with the Captivate...or does it vary depending on each users profile/ phones?
So Ive been playing around with various settings for set cpu and voltage control and all has been well so far. The only problem im having is voltage control seems broke. I try to open the all but it just black screens. I tried to clear the memory and unistall and reinstall and still have the same problem. Any ideas?
http://forum.xda-developers.com/attachment.php?attachmentid=432086&d=1288709102
^you can under volt setirons kernel and disable overclocking with this app.
i find my battery life to be less than stock with this kernel, i need to see if it is a common issue, maybe because it is not a captivate kernel. but in the past with unhelpfuls kernel for 2.1 battery life was awesome.
spartan062984 said:
Interesting stuff...
I too would like to know if it is possible to simply under-volt. Does anyone know the optimal settings for SetCpu with the Captivate...or does it vary depending on each users profile/ phones?
Click to expand...
Click to collapse
It's going to depend on the individual CPU in your phone. Your best result is to start at a given clock speed and begin lowering voltage in the smallest step possible, test for stability, repeat until you begin to notice instability (or you just run out of voltage options). You can just undervolt without increasing clock speed any, or you can not undervolt yet raise clock speed, or you can overclock and undervolt, depending on how your particular chip reacts. Some might need additional voltage to stabilize the snapdragon at 1.2Ghz while others (mine for example) is stable Able @ -100mV and 1.2Ghz. Overclocking silicon is the ultimate in YMMV.
Another thing to bear in mind is that increasing clock speed necessarily increases power consumption. There is no way around this. So a chip at 1.2Ghz will use more juice than 1Ghz even with the same voltage. It's difficult to say at this point whether, say, the Snapdragon @ 1.2Ghz and -100mV uses more or less power than the same chip @1Ghz and stock voltage. It's absolutely possible that the former uses more power, which would explain why you see at least one claim here of battery life decreasing even when voltage settings are left untouched.
hawkeyefan said:
It's going to depend on the individual CPU in your phone. Your best result is to start at a given clock speed and begin lowering voltage in the smallest step possible, test for stability, repeat until you begin to notice instability (or you just run out of voltage options). You can just undervolt without increasing clock speed any, or you can not undervolt yet raise clock speed, or you can overclock and undervolt, depending on how your particular chip reacts. Some might need additional voltage to stabilize the snapdragon at 1.2Ghz while others (mine for example) is stable Able @ -100mV and 1.2Ghz. Overclocking silicon is the ultimate in YMMV.
Another thing to bear in mind is that increasing clock speed necessarily increases power consumption. There is no way around this. So a chip at 1.2Ghz will use more juice than 1Ghz even with the same voltage. It's difficult to say at this point whether, say, the Snapdragon @ 1.2Ghz and -100mV uses more or less power than the same chip @1Ghz and stock voltage. It's absolutely possible that the former uses more power, which would explain why you see at least one claim here of battery life decreasing even when voltage settings are left untouched.
Click to expand...
Click to collapse
Thanks for clarifying Hawkeye! I will report back on in a few days once i have tested out a few profiles. In my opinion, I feel that it is best to leave Over-clocking at default and maximize battery utilization with setcpu. However, the thought of over-clocking the Dragon beast is VERY tempting. Who wouldn't? I will definitely check out the differences when playing games and such.
spartan062984 said:
Thanks for clarifying Hawkeye! I will report back on in a few days once i have tested out a few profiles. In my opinion, I feel that it is best to leave Over-clocking at default and maximize battery utilization with setcpu. However, the thought of over-clocking the Dragon beast is VERY tempting. Who wouldn't? I will definitely check out the differences when playing games and such.
Click to expand...
Click to collapse
I have to tell you, I'm not personally very fond of SetCPU on this device, even though I paid for the app (ugh). With raspdeep's voltage control app and SetIron's OC/UV kernel, the CPU defaults to 1.2Ghz at stock voltage, which for a basic setup is fine. Voltage Control app is phenomenal for adjusting in increments of 25mv at a time...one setting is for high clocks (1Ghz - 1.2Ghz) and the other is for < 1Ghz. It's probably best actually to start with the lower clock setting in Voltage Control, as your phone will spend the lion's share of it's time at those clocks and so that is where you should see the most gain in battery life. My only gripe is that I can't get the boot settings to stick on the Captivate so I have to go in and adjust them each time I reboot the phone. no biggie there.
SetCPU, on the other hand, has caused me loads of problems in the past, including causing the phone not to wake up from sleep and just atrocious battery life, I assume from constantly polling the CPU clock to measure clock speed. I have not experienced any of that with Overclock Widget, but I also don't use any of the independent clockspeed controls in the app...basically it's just a widget to display clock speed the way I use it. Otherwise, Setiron's kernel gives the 200mhz overclock and I just let the Hummingbird deal with changing clocks on its own. Jmo, but it works for me with no resulting battery drain beyond the additional I expect as a result of the extra 200mhz.
edit: whoops, long day. hummingbird in my post from above, not snapdragon. I need a drinky poo.
hawkeyefan said:
I have to tell you, I'm not personally very fond of SetCPU on this device, even though I paid for the app (ugh). With raspdeep's voltage control app and SetIron's OC/UV kernel, the CPU defaults to 1.2Ghz at stock voltage, which for a basic setup is fine. Voltage Control app is phenomenal for adjusting in increments of 25mv at a time...one setting is for high clocks (1Ghz - 1.2Ghz) and the other is for < 1Ghz. It's probably best actually to start with the lower clock setting in Voltage Control, as your phone will spend the lion's share of it's time at those clocks and so that is where you should see the most gain in battery life. My only gripe is that I can't get the boot settings to stick on the Captivate so I have to go in and adjust them each time I reboot the phone. no biggie there.
SetCPU, on the other hand, has caused me loads of problems in the past, including causing the phone not to wake up from sleep and just atrocious battery life, I assume from constantly polling the CPU clock to measure clock speed. I have not experienced any of that with Overclock Widget, but I also don't use any of the independent clockspeed controls in the app...basically it's just a widget to display clock speed the way I use it. Otherwise, Setiron's kernel gives the 200mhz overclock and I just let the Hummingbird deal with changing clocks on its own. Jmo, but it works for me with no resulting battery drain beyond the additional I expect as a result of the extra 200mhz.
edit: whoops, long day. hummingbird in my post from above, not snapdragon. I need a drinky poo.
Click to expand...
Click to collapse
LOL. No Worries. I myself made the same mistake. I thought something was odd with my post. SnapDragon...Hummingbird....Bulbasaur.....I knew what you meant. lol
Still not having any luck with the voltage control app. Ive tried flashing different roms to see if it would work. I undervolted it to 100/75 the first time i did it and now i cant change. Only a little worried
i guess there was an issue with the set on boot scripts not working. supposedly that is fixed, i dont know for sure though, i haven't updated.
From what I'm gathering, in order to undervolt, you must have a kernel to su pport that, for example Setirons.
I'm not necessarily interested in overclocking, as it performs well as is. Of course there are arguments that overclocking may ultimately harm the phone, and arguments that by the time that happens, you'd be ready for a new phone. In any event, if I start getting slower, I may interest in overclocking.
Does anyone know if dramatic improvement in battery performance with underclocking?
I've noticed quite a bit of a difference, just pretty difficult to tune it precisely. (Coming from a person who enjoys overclocking computers a little too much). I just wish there was an app that would test each frequency and then let you know which one failed (without having to manually set it).
I am loving my Android experience so far coming from and iPhone 4. I am running LeeDroid and have been playing around a lot with SetCPU. At this time, I am not concerned about battery as of yet. I am asking this question in regard to optimal, blazing fast performance with minimal hiccups.
I have done Quadrant testing at various min/max CPU levels. I had excellent results at 1804 high 904 min. However I had to yank the battery after not being able to unlock the device.
For profiles, real basic, again I am not concerned about battery charge life ATM. I have it set to revert to stock performace (1036/245) if the battery temp reaches 100F.
With the screen locked, I have it set to 499/245. All of my settings are using the "ondemand".
I would like to know what an ideal minimum is for PERFORMANCE as well as ideal max (1804? Highest might not always be fastest?). I got amazing results with Quadrant full benchmark with settings of 1804/499. This also caused a lockup when trying to unlock the device though. Maybe because there was a conflict with my lockscreen max setting? I would think the app would put priority to the lock profile though.
Also, does this phone have a built in CPU temperature sensor that I could utilize with a CPU temp widget?
Thanks for reading my lengthy ramblings.
Ray
A. This thread belongs in the q&a
B. Some inspires can't that much of an overclock, might seem like yours is one of them
C. You might get more help if you post in the leedroid thread
Sent from my Inspire 4G using XDA Premium App
Thanks for your excellent A, B, C format response. I'll head elsewhere.
Hey guys,
Ive been using SetCPU since it was fixed for the sensation. I am curious about what others have observed as far as battery life and performance goes.
I am running 1.8Ghz with a cpu voltage of 1.265V (1265000uV).
My battery doesnt last all that long despite all the profiles I have in place. I guess thats expected when you overclock by that much, huh? Is it worth it though?
Im sure more of you out there have experience to share. Im not talking Quadrant and benchmark scores, Im talking REAL use!
I am beginning to feel that dropping the frequency down may be in order since I cannot find anything that needs 1.8Ghz to work on this phone. Plus, less frequency means less required voltage. That would mean more battery!
Anyone care to chime in with their overclock frequency + voltage and experience?
Matt
I'm also interested in getting some input from other users, without having to clog up the respective overclocking threads in the Development section.
Yesterday after work, I set up the 1.5Ghz Undervolted option using utking's tool (http://forum.xda-developers.com/showthread.php?t=1168707). I didn't see too much need to push my CPU too hard, and a stable UV always piques my interest.
I created a couple of basic SetCPU profiles (screen off, battery below 20%, temperature < 50C), and scaling on demand up to 1512Mhz, my phone took about another 7-8 hours of moderately heavy use (Navigation, Maps, Yelp, photos, etc.) before it was on its last legs.
Bear in mind that I've been using the Anker 1900mAh battery. But even after the OC-UV that I set up, this was at least as good of battery usage as before without any SetCPU or overclocking, and actually seemed to be a little bit better to be honest.
I just dropped down to 1.6Ghz @ 1.26V...
I couldn't keep my phone from freezing with anything less than 1.26V @ 1.6Ghz. We will see how this goes for a few days and compare to my previous 1.8Ghz @ 1.265V.
So far, speed seems to be FASTER than 1.8Ghz. My Quadrant score (only being used here for comparison reasons) was 2700 right off the bat, whereas 1.8Ghz would peak around 2700-2800 after several tries.
The carousel works much better! I can swipe through quickly and have it scroll with zero lag. I can also fast swipe and watch is spin nicely!
Google Earth and Maps is about the same as 1.8Ghz.
Before, at 1.8Ghz, I could probably get 16 hours out of my phone with VERY LIGHT use. (A few 2min phone calls, check mail throughout the day, check the web a little). I am charging the phone up and will report back later.
Matt
I went down from 1.62 UV to 1.5 UV,because I could not see any difference in general use nad in benchmarks(except Quadrant) and battery consumption is much bigger with 1.62 with exact same profiles on setCpu.I think that this is best compromise between speed and battery life and as far as I know this is native clock speed of 8260 Snapdragon.
mrg02d said:
I just dropped down to 1.6Ghz @ 1.26V...
I couldn't keep my phone from freezing with anything less than 1.26V @ 1.6Ghz. We will see how this goes for a few days and compare to my previous 1.8Ghz @ 1.265V.
So far, speed seems to be FASTER than 1.8Ghz. My Quadrant score (only being used here for comparison reasons) was 2700 right off the bat, whereas 1.8Ghz would peak around 2700-2800 after several tries.
The carousel works much better! I can swipe through quickly and have it scroll with zero lag. I can also fast swipe and watch is spin nicely!
Google Earth and Maps is about the same as 1.8Ghz.
Before, at 1.8Ghz, I could probably get 16 hours out of my phone with VERY LIGHT use. (A few 2min phone calls, check mail throughout the day, check the web a little). I am charging the phone up and will report back later.
Matt
Click to expand...
Click to collapse
How simple is it to temp-root and overclock? I am really only interested in overclocking to speed up Sense, and you said it performs better with a speed boost.
Sent from my HTC Sensation 4G using XDA Premium App
Very,very easy,just read this tread :http://forum.xda-developers.com/showthread.php?t=1168707
I have mine undervolted at VDD_1175000 and 1500MHz. I like it very much...makes a big difference in quadarant score, but not sure in reality how much faster. Battery life is fine (when the phone is on). Have not experiened FC's
I have modified eugenes batch file to push my kernel file and preferred speed after perma-temp-root and now is all in one click...
So here is a little update:
Its been about 8 hours since full charge and I am at 55% battery left.
1.6Ghz @ 1.26V, On Demand.
Ive been checking email, making a few calls, and surfing the net with both wifi and GPRS (was out of the network, away from 4G). I also played Angry birds for a little bit and showed off Google Maps and Earth to my Mom.
Now that Im back home, ive turned back on 4G...
Ive noticed a slight amount of hesitation while opening and closing things, but nothing bad.
I havent had any profiles kick in yet, but they will soon with the battery getting low. I will resist charging the phone and see if I make it through the night, using it as I need it. I will report tomorrow.
Matt
I must be doing something wrong.
I am rooted and running LeeDriods 1.2 Rom. When I launch setcpu the only options i have are 1000 mghz? WTF am i doing wrong?
i think at LeeDroid 1.2 you must not use setcpu but Demon control?
BigBoppa said:
i think at LeeDroid 1.2 you must not use setcpu but Demon control?
Click to expand...
Click to collapse
Hmmm, okay. I saw where set cpu was updated for the sensation in the latest release but it doesn't seem to support overclocking with this rom.
Shame that as i was about to get that rom and flash it onto my phone, glad i came in here now
Running Leedroid 1.0
Kernel @ 1.7ghz max, i have it set to 1.5ghz and 192mhz
Runs hot when i play finger racing or reckless racing or modern combat 2 or something intensive, but besides the heat, it drains just like it normally would to be honest, maybe a little quicker, definite speed increase in overall user experience, without an OC the rom just flops, better than stock but just crap, OC is needed.
This is my third time typing this... (This website should really have an auto-save draft feature)
I recently installed the application "CPU Tuner" because I've always wanted to utilize my newly rooted phone. The phone is running Cyanogenmod 7.2 Stable, and currently overclocked at 1.5GHz. My main concern is overclocking my phone that high. Now, I didn't really choose that option, SetCPU automatically set it to that when it loaded a configuration. I'm a beginner to overclocking, and this is my first time doing it for anything. I've heard rumors of people melting their processors from overclocking it, so I want to know if it's okay if its overclocked to roughly twice the stock frequency of 800MHz. If it IS safe, then why isn't the phone automatically set to 1GHz to compare to it's twin, the Evo 4G? Or perhaps even 1.2GHz to surpass it? I would definitely be satisfied with 1.2GHz, but I wouldn't mind having 1.5GHz if it was stable and didn't drain the battery. On to the next question, would an OC this high cause instability and/or would it drain my battery? I only overclocked an hour ago, so I haven't experienced any problems whatsoever... yet. On to the profiles... I'd like some suggestions for improving my triggers. Right now, it set everything up to the highest frequency, but looking at the help, it said to not touch the frequency, but experiment with thresholds. In the Help, it doesn't tell you what the thresholds are, and what they do, and more importantly, how they work. It just shows that the highest is the most battery saving. I would have thought the lower the better, but... Anyway, if you could tell me, I'd be highly appreciated it. Finally, the battery temperature... It has an option to enable a setting to change profiles if the battery gets a certain temperature, but I'd like to know what would be considered "Overheating". I get paranoid when the battery temperature gets a little warm at around 36 Celsius... but the profile it switches to is supposed to really slow down the CPU to preserve battery, so I'd really rather not use it unless it's necessary. So, would 45 - 50 Celsius do, or should I set it a bit lower? My battery is 4000+ mV, if that'd help at all. If you know any sources that you can direct me to that would answer my questions, it'd be highly appreciated.
Wow ok . Well first off check out THIS thread. It will explain a lot about Governors, I/O Schedulers, and a bunch of the questions you have. As for people melting CPUs, I've never actually seen it happen, or know anyone who has had it happen on the Shift. That's not to say it's not possible. It may be, just not probable. The Shift processor compared to the OG EVO's is much better. The Shift even at the stock 800mHz out performs the EVO's processor at 1000mHz. That is in part because it is a 2nd Gen processor vs the EVO's 1st Gen Unit. The Battery Temp should try and always be kept below 115-120 Degrees Fahrenheit. I use SetCPU, and have a Profile that kicks in to lower the OC to around Stock should the Battery Temp every reach 110 Degrees Fahrenheit. My setting are 61mHz Min 1516mHz Max, Smartass V2 Governor, and SIO Scheduler. But every device is different, so your going to have to do a bit of experimenting till you find what works for you. If you get a lot of Random Reboots, lower your Max OC setting, or try a different Governor. BTW where did you get a 4000mAh Battery?
prboy1969 said:
Wow ok . Well first off check out THIS thread. It will explain a lot about Governors, I/O Schedulers, and a bunch of the questions you have. As for people melting CPUs, I've never actually seen it happen, or know anyone who has had it happen on the Shift. That's not to say it's not possible. It may be, just not probable. The Shift processor compared to the OG EVO's is much better. The Shift even at the stock 800mHz out performs the EVO's processor at 1000mHz. That is in part because it is a 2nd Gen processor vs the EVO's 1st Gen Unit. The Battery Temp should try and always be kept below 115-120 Degrees Fahrenheit. I use SetCPU, and have a Profile that kicks in to lower the OC to around Stock should the Battery Temp every reach 110 Degrees Fahrenheit. My setting are 61mHz Min 1516mHz Max, Smartass V2 Governor, and SIO Scheduler. But every device is different, so your going to have to do a bit of experimenting till you find what works for you. If you get a lot of Random Reboots, lower your Max OC setting, or try a different Governor. BTW where did you get a 4000mAh Battery?
Click to expand...
Click to collapse
Thanks for the response. It's pretty late, so I've bookmarked the link to read tomorrow. Alright, so 45 degrees Celsius should the maximum then. I've been thinking of switching over to SetCPU, since there are more comprehensive guides than for CPU Tuner (In which no one seems to have heard about), and it doesn't seem that the settings it set will be ideal for the long run. Although, before I switch over to SetCPU, I want to at least give it a shot. I'll change my settings so that the frequency decreases depending on battery level. Also, I don't have much but the basic governors and configurations on CPU Tuner, so I've never heard of Smartass V2 (Prior to skimming through the link you posted). Also, the battery came with it, I knew it seemed a bit different from most other batteries (From what I've seen in searches, most of them had around 2000), but I didn't know it meant that much.
The Governor settings available will depend on the Kernel, not on the CPU Controller. I've always been partial to SetCPU, but that's just me. I would again suggest doing a bit of reading, and experimentation to find your best settings. But defiantly the closer to normal the Battery temperature is the better. When the Battery heats up to much it will in most cases also drain faster. If you can post a Pic of the Battery I would really like to see it. I've never come across a 400mAh Battery for the Shift.
When I first rooted my shift 2 years ago I was very concerned of over-heating. I constantly checked the temperature. After a while I realized it is quite hard to over heat and cause damage, especially with the newest kernels the devs have put out. Just experiment with different settings and see what works best for your phone
Sent from my PG06100 using xda app-developers app
Hello guys
I'm not a new user in kernels or ROMs .
I have a low-decent battery life ,and I'm sure there's a way to get a better battery life with undervolting .
I want to know
what is "undervolting" ?
What is the biggest damage it can cause?
What is PVS?
How do I know ,how much I can UV?
What are the steps to undervolt?
What I gain from UV (despite battery life)?
For your info ,I'm using AOSPAL ROM +FAUX's latest 16u kernel .
Thanks
Sent from my Nexus 5 using XDA Premium 4 mobile app
http://forum.xda-developers.com/showthread.php?t=2537000
Sent from my Nexus 5 using Tapatalk
Hi,
Most of your questions have a reply:
About undervolting: http://forum.xda-developers.com/google-nexus-5/general/nexus-5-undervolting-thread-t2537000.
CPU binning: http://forum.xda-developers.com/google-nexus-5/general/cpu-binning-nexus-5-t2515593.
The "risks" are instability like hard reboot, SOD, etc.... To find a "safe" value you will need to test by yourself to find what undervolting your CPU can handle, not all CPU's are equals.
Undervolt by steps like - 25mV, don't set your new values at boot unless your are sure it's stable (or you could encounter bootloop), test for a few days under different conditions (as your use).
The gain apart battery life (but you will not gain that much as people tend to think) is a little less heat, but again nothing huge..., better is to test by yourself and see what you will gain... or not.
Battery life depends mainly of your use, apps, signal quality and settings like, screen brightness, synchro, CPU governor, etc... In my opinion check first what could be the cause of your low battery life (and what is low battery life for you???) before play with undervolting.
As said above, undervolting will get you very minor battery life increases.
More than likely you have an issue, or its just your setup and usage giving you the battery life you are seeing.
Undervolting will not change any of this.... You'll gain only minutes of battery time.
Try some troubleshooting in the below thread to see if you have an issue, or how to setup for better battery life. Read through it a bit, from the last page and work back a bit. You can post meaningful screenshots there too. From gsam or BBS.... not the stock battery screen, it has no real useful info for finding issues. Good luck!!
http://forum.xda-developers.com/showthread.php?t=2509132
Nexus 5 Battery Results
I've been undervolting many systems for many years, primarily Linux desktops and some servers, and the primary benefit is that you get less heat output which means when running cpu-intensive tasks the temperature climbs slower so the throttling of the clockspeed kicks in later, so your phone will be faster in certain situations. If you take a phone which has been idle for a while and run a benchmark, and then immediately run that benchmark again, the 2nd time gets a lower result as the phone is still hot from the 1st. This makes drawing conclusions about settings really dificult but it illustrate that throttling from heat is affecting speed.
For most users their perception will be the phone runs cooler.
You do undervolt at each step in the processor's frequency, and each step is a trial+error activity, the throttling I mention means finding a stable under-volt at the higher frequency which is labour-intensive,i.e take the max clock, and undervolt it a little, run a benchmark which forces it to run at high clockspeed, and if it passes that test then run it again at the next step down in frequency. Once you've got the most stable top clockspeed, then do it progressively for all the other voltages on the way down.
In some platforms in Linux and Windoze, we wrote scripts which save the stable voltages and then undervolts a little and runs a stress-testing benchmark and if the system hung it wouldn't save the current voltages so the previous higher voltages were safer, stick that script in a startup script area and leave the compute to do many self resets, and you've calculated your device's voltage range. I wonder if someone has that done for Android??? For a laptop the FAN would run slower saving battery time and for laptops that would lead to say 20% better battery life but on a phone it won't make much saving as no fan.
Your phone will run most of its time (like 95%) at its lowest frequency, so for effort/benefit just focusing on dropping its voltage will gain the most in the phone running cooler.
Battery life improvement is marginal, if you look at your battery stats its down to your application settings and screen brightness, i.e. how you use and what you do with your phone. So if your battery life is bad, use your phone less!
I carry a slim USB battery, it is the $/effort/benefit the best thing you can do, $20 doubles your battery life, if you get one with a 1.5A-2A output in just a few minutes when the phone doesn't mind a battery attached, will dwarth every possible tweak and hack anyone can form in benefit.