No USB and No Camera connection after cyanogenmod - General Questions and Answers

hi,
after i installed >THIS< on my optimus one two things don't work anymore:
the usb connection to any pc
the camera don't work "no connection to camera"
i hope anyone can help me and my lg p500.
thank you all very much!!!!

Look at these:
"Reported Bugs:
Wifi Calling aint connecting
ADB not displaying although its working... known issue with older kernels
USB Tethering does not work. (once again old kernel with specific patches needed)
Bluetooth not working to its full potential.
Headset audio is mono. (Problem on similar phones still looking into issue)
Broke camera"
That was easy - install other android or wait to upgrade
Good luck

Related

Bluetooth issue with new roms

Is there a download with the old bluetooth stack that I can install over the one in my rom? I am using nueroms latest titan rom but my Redfly wont connect because it keeps saying "turn on bluetooth" before authorizing.
try the link to the Definitive Guide to Bluetooth Services in my signature...
it has 2 stacks.. microsoft and toshiba
If I am not mistaken, those bluetooth stacks are on the PC side of things?
I dont have the need to sync with a PC. I am trying to connect my redfly to my phone. this worked fine with older roms but doesnt with newer roms. (it keeps saying turn on bluetooth when it is) Other than that issue bluetooth works fine with other bluetooth hw. (headset, pc connection)
Any other suggestions?
Thank you for your replies.

[Q] Does Team Tiamat Xoom Rom support MTP/PTP?

recently i tried to connect my nikon D7000 to my xoom, but it just couldn't recognize the camera. the camera can be read by my laptop through the same cable and my xoom can mount thumb drivers and hard drivers, which implies that the otg cable and the usb cable are ok. so i searched a lot about the problem. i found that many people faces the same problem. see the following thread
http://forum.xda-developers.com/showthread.php?t=1142257
but there is no solution to it.
then i made a test. my mobile phone is nokia n78. it supports both massive storage protocol(is that right?) and picture transfer protocol . when i use the massive storage protocol to connect to my xoom . it works nicely, just like a thumb driver. however ,when i use ptp to connect my xoom, nothing happens to my xoom(just the same as my d7000). so i doubt whether there is some problems with ptp?
i also found that many people can connect their dslr to xoom
see
http://forum.xda-developers.com/showthread.php?t=1095828
http://www.youtube.com/watch?v=o1EwD375itw
http://forum.xda-developers.com/archive/index.php/t-1287194.html
so maybe the problem exists in the rom ? or the kernel? or i need some drivers?
does anyone know how to solve the problem? or it is a known bug of tiamat rom?
anyone can help ?
Hi,
is there any update on this issue?
I have a Xoom running the UMTS_everest Nightly Build 45 of Team EOS.
I have no problem connecting USB devices to my tablet, but when I connect a camera in PTP mode to my tablet, nothing happens.
Regards
Jim

Bluetooth drivers missing?

Hi all, I'm trying to setup my Xoom to Bluetooth connect with my laptop. It connects and pairs, but when connected two devices show up in device manager saying they need drivers. When I look at my Bluetooth devices it says the Xoom needs troubleshooting. I just updated my Bluetooth drivers I'm gonna work on updating the Bluetooth stack on my laptop. I also updated my WiFi drivers in the case they were effecting BT. Any thoughts?
Thanks in advance
_______________________________________
Because the cramp just won't go away!

Monitor mode solution?maybe i've got it

Hi guys, maybe i've found a monitor mode solution that works on our nexus 5 devices, unfortunately i can't test if it works, cause i haven't the correct Wifi adapter.
Omni rom is required, i've found a kernel(i've only tested on omni like the developer of this kernel) that install usb host driver for atheros and tl-wn722n wifi usb adapters on nexus 5.
I've tried to flash this kernel and all fine, but now i can't test if monitor mode works cause i have none of these usb wifi adapters.
if granted leave you the link of the page of the kernel : http://www.maxters.net/2014/03/nexus-5-usb-wifi-kernel/
The page and the kernel is not mine, i've only found them on google looking for a solution, and would like to share, to finally give an answer to the many questions on monitor mode.
If someone can try please, give me some feedback if it works fine or no, cause i have yet to buy wifi adapter, and for now can't do nothing.

Android on W1-810

This is a windows tablet, but I think it would be cool to have this run android as well, so I tried a few emulators running under windows 10, but they are very slow, unstable or didnt run at all. Doid4X, an Nox worked, Andy refused to start).
I kept the Nox App Player, cause that was the one I found most responsive of these.
Perhaps the fact that they barely meets the minimum RAM requirement is a major cause for it being slow.
Then I decided to try the android-x86, which is not an emulator, but an andoid port to x86, and will run natively.
The Lollipop EFI image does work as a live usb media , and I was able to install it to another usb stick, but that got stuck on the aandoid logo when booting. The 4.4r3 EFI image did work better, and was able to install to a second usb stick and boot up into android.
I must say that android-x86 did impress me. It feels quite quick and responsive, and any app I have tried so far does run. Even MineCraft PE works well. The display and touchscreen works well, and volume buttons works.
There are a few driver related issues though, here is a list of some things not working:
- onboard wifi
- onboard Bluetooth
- Sensors (auto rotate will not work)
- Audio out and mic
- Power button
- Battery status
- Camera
I did a few tests, and as a workaround I did use an external usb wifi adapter to get internet working. Also connecting a usb headset with mic did work fine, external keyboard. Also a non branded bluetooth adapter was accepted and the BT icon was enabled, but it didnt find any devices when searching. Even a logitech webcam did work with opencam.
Given the current state of andoid-x86 on this tab, it doesnt make sense to partition the disk to get a dual boot. But if there was working drivers for wifi and audio etc, this could be a decent android system.
Now the android version of the tab 8 looks quite similar to the w1-810, so that makes me wonder how much of the hardware components that are the same. And if it may be possible to get the drivers from the original android to work on android-x86.
I will try to list the hw configuration as I can read from devicemanager/drivers in win10:
wifi: broadcom 4330 / Sound: intel SST audio device / camera: Intel Imaging signal processor 2400 / Bluetooth: BCMBTBUS / Sensors: BMA2x2 ( BMA250E) / Battery control hardware ID is PNP0C0A
Any ideas on how to get these things working would be great.
forum administrators:
I did tag this thread with iconia-tab-8, but for some reason it will not show under "Acer Iconia Tab 8 Discussion" list.
Did I miss something, or doesnt the tag system work properly.
Is there anything I can do to fix this?
I also have this tablet and I am also eager for installing fully functional Android on it. Please guys help us on this. Thanks in advance.
News about Acer Iconia Tab W1-810 with Android
Hi guys, some new about it?

Categories

Resources