Hi guys,
I just bought a SGT from a friend and id a hard reset to "clean" it up and have a new start. Before the reset the wifi worked (although i had to disconnect and then reconnect a few times when watching a youtube vid for example). Now after the hard reset the wifi doesn't work at all. It recognizes the SSID of my wifi router and treis to connect but after a few seconds he states a disconnect. My router is a D Link DIR-635. Does anyone know this problem and can provide some helo? I'm fairly new to android and seem to have a bad start with it...
EDIT: I guess it has something to do with WPA, because if I deactivate everything (WEP,WPA,etc) it works. But of course I want to activate the security. Sorry for my poor English by the way... I hope ya'll understand what I mean
Solved: I needed to choose TKIP under WPA mode. I don't know why but it works. Thread can be closed.
Related
so guys when am at my firends place i connect to his router no problem, however at home it doesn't see my wifi router though my router is set on discoverable and my other laptop connects to it, is there any other reason why this might be happening, another question a bit out of this subject, i was under the impression that the keyboard has back light, however i found nothing that suggests that
regards
Rabia said:
so guys when am at my firends place i connect to his router no problem, however at home it doesn't see my wifi router though my router is set on discoverable and my other laptop connects to it, is there any other reason why this might be happening, another question a bit out of this subject, i was under the impression that the keyboard has back light, however i found nothing that suggests that
regards
Click to expand...
Click to collapse
More details as to the type of router you're using a/b/g/n? The keyboard DOES NOT have backlight. You can use the fingertouch screen keyboard for that, which IMO works fine. Hope this helps.
well thanks it was belking and after searching a reading i found its belkins N fault, after performing a firmware upgrade it worked like charm
thanks for your help anyways
I have spent the last week at work more focused on the XDA forum than what I am actually paid to do here at work...
I am so unproductive now, I am actually willing to donate to the forum if the forum can produce results, so that I can finally get back to work in peace!
I have thoroughly read through most relevant posts. I cannot find any specific post that solves the problem I have, so I decided to post anew, against some suggestions...
Anyway, the problem is that,
I cannot get any of my applications that are internet-dependent (skype, mail, weather etc) to access the WIFI connection that "apparently" looks connected, IF WEP (or any other encryption, for that matter) is enabled on the WIFI Router.
OK, what I mean by "apparently" is that the Wifi signal appears at its fullest, the lollipop on top of the screen with arrows is there, and even if I go into start>settings>Connections>wifi, it says that (my particular internet connection, named) Linksys is "connected".
The problem is, with wep encryption (and any other encryptions), it has worked once or twice. I cannot remember if that was before or after the Hard-SPL and radio downgrade (to get it unlocked) but ever since that "beginners luck" connection, I have had no success with connecting these apps to internet through WIFI.
First of all, I cannot figure out why, but I can connect by
1/ GPRS (the only available here in Vietnam - no 3G /HSDPA yet),
2/ with open connection and no encryptions of any kind by the WIFI router, my WIFI and Raphael connects fine. Data transfer happens.
The reality is, it is not very realistic for me to ask all others at work to make their WIFI connection with no security or encryptions..
So, having explained the situation, in a nutshell, problem is that by enabling excryption like WEP, the connection does not allow me to use WIFI on my raphael.
Is this hardware or software on Raphael side? or is it WIFI router side?
Other devices, including my TyTn II connects fine with WEP, which rules out the router, right?
I cannot remember if the problem started before or after OliPro unlock...
If it worked before but not now, there is of course always the possibility of hardware mulfunction, but since it works with no encryption, I am guessing it is hardware?
I have gone to other WIFI networks that are healthy, with other hand held devices happily connected to WIF, but nope...not me...
Any ideas guys?
WRT54G2 Wireless_G Router
DHCP Enabled,
Wireless network mode is set at mixed (both G and B, but by the way, I have tried only G and only B too, with no luck)
Channel set at 1, SSID enabled.
WM 6.1
ROM 3.14.731.04 JPN
Radio 1.10 Olinex
Protocol 52.35.25.21H
AFAIK, Raphael connects to WEP, WPA, WPA2(TKIP/AES)...
did you try deleting all the wifi settings and reconnecting?
or hard reset?
jewelkobayashi said:
I have spent the last week at work more focused on the XDA forum than what I am actually paid to do here at work...
I am so unproductive now, I am actually willing to donate to the forum if the forum can produce results, so that I can finally get back to work in peace!
I have thoroughly read through most relevant posts. I cannot find any specific post that solves the problem I have, so I decided to post anew, against some suggestions...
Anyway, the problem is that,
I cannot get any of my applications that are internet-dependent (skype, mail, weather etc) to access the WIFI connection that "apparently" looks connected, IF WEP (or any other encryption, for that matter) is enabled on the WIFI Router.
OK, what I mean by "apparently" is that the Wifi signal appears at its fullest, the lollipop on top of the screen with arrows is there, and even if I go into start>settings>Connections>wifi, it says that (my particular internet connection, named) Linksys is "connected".
The problem is, with wep encryption (and any other encryptions), it has worked once or twice. I cannot remember if that was before or after the Hard-SPL and radio downgrade (to get it unlocked) but ever since that "beginners luck" connection, I have had no success with connecting these apps to internet through WIFI.
First of all, I cannot figure out why, but I can connect by
1/ GPRS (the only available here in Vietnam - no 3G /HSDPA yet),
2/ with open connection and no encryptions of any kind by the WIFI router, my WIFI and Raphael connects fine. Data transfer happens.
The reality is, it is not very realistic for me to ask all others at work to make their WIFI connection with no security or encryptions..
So, having explained the situation, in a nutshell, problem is that by enabling excryption like WEP, the connection does not allow me to use WIFI on my raphael.
Is this hardware or software on Raphael side? or is it WIFI router side?
Other devices, including my TyTn II connects fine with WEP, which rules out the router, right?
I cannot remember if the problem started before or after OliPro unlock...
If it worked before but not now, there is of course always the possibility of hardware mulfunction, but since it works with no encryption, I am guessing it is hardware?
I have gone to other WIFI networks that are healthy, with other hand held devices happily connected to WIF, but nope...not me...
Any ideas guys?
WRT54G2 Wireless_G Router
DHCP Enabled,
Wireless network mode is set at mixed (both G and B, but by the way, I have tried only G and only B too, with no luck)
Channel set at 1, SSID enabled.
WM 6.1
ROM 3.14.731.04 JPN
Radio 1.10 Olinex
Protocol 52.35.25.21H
Click to expand...
Click to collapse
I completely understand what you are going through & I am going to suggest something for you but the results might vary.
Make sure that Wi-Fi is turned off.
Open your Comm Manager | Settings | Wireless LAN.
When you're in the Wireless LAN Settings panel, select Power Mode.
Slide the selector to Best Performance.
Tap OK & when you're back in the Comm Manager, turn on the Wi-Fi adapter.
Setup your work connection & see if your internet connections work.
One thing to note, while this has resolved my connectivity problems, the settings are not always saved for some unknown reason.
So, be prepared to key in the settings again.
I resorted to everything , not leaving anything to chance, and did many things at once.
It is now fixed, it seems, but at great cost in terms of time, and I cannot be sure which one of these was actually helpful.
But I hard-reset the TP, as well as updating the firmware on both the modem and the WIFI router, and then did hard reset on them too...
I cannot judge on what turned out to be true on other peoples' TP, but for me at least, for both TyTn II and Touch Pro I am currently using, setting connection from "internet" to> "Work" did not help at all....
Thanks anyways...
HI,
My raph100 won't connect to even an unsecured open network! I've searched and searched and tried:
selecting 'best performance'
manual ip/gateway setting etc
new rom
using advanced config to disable wpa authentication
xdandroid
the 'configure wireless connection settings' finds my network, changes to 'connecting' and then after a while goes back to 'available'
i really don't know what else to do. i bought second had on ebay but fear i won't be able to get a refund.
i will look for some kind of hardware diagnostic tool to try and prove it's faulty.
i've seen that alot of people have this problem but solutions only work for some. lame.
hi again,
i plugged in a new access point to my router and set it up using another channel. touch pro connected no problem and i even used wep. however, for unrelated reasons i did a hard reset and now it won't connect again?!
this is driving me crazy any ideas?
Hi again,
I connected a new access point to my router and set it up with a different channel. Touch pro connected fine, even with wep. however, for unrelated reasons i did a hard reset and now i get the same problem as before!!
This is driving me crazy any ideas?
here is the relevant part of the log from my router
09:13:37 i802_1x:00:18:41:f3:9f:a1 disassociated
09:13:37 i802_1x:00:18:41:f3:9f:a1 associated
09:14:53 i802_1x:00:18:41:f3:9f:a1 disassociated
09:14:53 i802_1x:Closed session for 00:18:41:f3:9f:a1 (Supplicant logoff)
09:14:53 i802_1x:00:18:41:f3:9f:a1 disassociated
ok i did a search for WiFi problems everyone else's problem seems slightly different then mine
or not the same in the least
here is my problem
First i have NO data Plan so i turn 3g/4g off
then i Turn on WiFi and it works till i turn it off or reboot the phone
THEN even though it still connects to WiFi and my router says it's connected
i get no data throughput
no amount of resetting, deleting my router profile, rebooting phone, rebooting router, and messing with everything i can find INCLUDING setting my router to OPEN, changing the channel, changing from N to G or B from 40 mhz to 20
NOTHING works
EXCEPT
resetting phone to factory default
then it works again TILL i turn WiFi off or reboot/restart phone
any ideas ?
.
ok you can ignore this it has something to do with turning off the network 2g/3g/4g
I'm not sure what the setting is causing the problem, as I'm still looking into it
I'll post here when i find the setting that is causing the problem
in case it will help someone else
UPDATE:
ok under "Mobile network settings"
you can not turn off "Data enabled" (Enable data access over Mobile network)
why this affects WiFi i do not know as it should ONLY affect 2g/2g/4g
Because it says "Over Mobile network"
but it turns off WiFi data also
If i find anything else that effects WiFi I'll post it here
but for now this is the solution to my problem
PS: it's nice to be able to solve your own problem
PSS: don't call T-Mobile for help they will say you need flex pay or better plan to use WiFi, i hung up on the stupid bass-turd,
not to add to the fact it's super hard to understand their mangled English!
.
i got that problem last night, during my open box and testing the phone, all you have to do is reset the phone, then you are set to go; hope it works for you.
thanks for the reply
i found out what i was doing wrong
and edited my post
so others can not do what i did
thanks for the reply though
Maybe they did this on purpose to keep you from using the device with out a data plan. Who knows.
Has anybody tried to connect to a Time Capsule?? I cannot get my G2X to see my router for nothing. Is the G2X compatible with a N router??
s00paSold3r said:
Has anybody tried to connect to a Time Capsule?? I cannot get my G2X to see my router for nothing. Is the G2X compatible with a N router??
Click to expand...
Click to collapse
maybe you should open your own thread about this ?
i do not use "Time Capsule" and not sure what it is (A router?)
to answer your last question the G2X supports Wi-Fi 802.11 b/g/n, DLNA, Wi-Fi hotspot. so yes it supports the "N" standard
BUT
might not be compatible with ALL b/g/"N" routers
should be compatible with them all BUT might not be ...........
i am not an expert on routers, so cant say for sure
also could be that your router is to far away from your phone
your phones antenna is tiny, so has to be closer to the router then say a laptop or computer.
you might also want to consider going to a friends house and trying their wireless router.
anyway opening your own thread on this is your best bet
.
I have an airport extreme broadcasting mixed n/b/g and mine is really struggling. At first I thought it was the browser, but now it's doing it in both dolphin and the stock browser. It stalls a lot, connection seems to stop and restart. I already disabled wifi sleeping on the device. Pretty frustrating. Oh and mine is setup as hidden with no security on it at this time so that isn't the issue.
a1yet said:
maybe you should open your own thread about this ?
i do not use "Time Capsule" and not sure what it is (A router?)
to answer your last question the G2X supports Wi-Fi 802.11 b/g/n, DLNA, Wi-Fi hotspot. so yes it supports the "N" standard
BUT
might not be compatible with ALL b/g/"N" routers
should be compatible with them all BUT might not be ...........
i am not an expert on routers, so cant say for sure
also could be that your router is to far away from your phone
your phones antenna is tiny, so has to be closer to the router then say a laptop or computer.
you might also want to consider going to a friends house and trying their wireless router.
anyway opening your own thread on this is your best bet
.
Click to expand...
Click to collapse
I did start my own thread.... and the wireless works everywhere else I connect to, The Time Capsule works because my laptops and everything wireless is working ok.
At work we installed a new WiFi router a few months back. The connection is open and no one needs a password to connect to it. But many who bought android phones recently arent able to connect to it. I have a OnePlus One with android 4.4.4 which doesnt connect to the WiFi. My colleagues own Xiaomi, Motorola phones which they bought recently, which also doesnt connect to the internet.
The phones detect the WiFi signal, says the network is saved but fails to connect to it no matter what. The temporary solution is to make our laptop into a WiFi router and use it but this is seriously annoying. The router is from HP and I dont know the exam model number for it at the moment
I will be grateful if someone can find any solution for this problem. Also, I am a novice when it comes to gadgets so, if your suggestion is to manually set up my WiFi settings please do so with clear instructions or a video of some sort. However I will be happy if this problem gets solved in a straightforward manner.
Please help!
XDA Visitor said:
At work we installed a new WiFi router a few months back. The connection is open and no one needs a password to connect to it. But many who bought android phones recently arent able to connect to it. I have a OnePlus One with android 4.4.4 which doesnt connect to the WiFi. My colleagues own Xiaomi, Motorola phones which they bought recently, which also doesnt connect to the internet.
The phones detect the WiFi signal, says the network is saved but fails to connect to it no matter what. The temporary solution is to make our laptop into a WiFi router and use it but this is seriously annoying. The router is from HP and I dont know the exam model number for it at the moment
I will be grateful if someone can find any solution for this problem. Also, I am a novice when it comes to gadgets so, if your suggestion is to manually set up my WiFi settings please do so with clear instructions or a video of some sort. However I will be happy if this problem gets solved in a straightforward manner.
Please help!
Click to expand...
Click to collapse
No need to configure wifi on your device IMO.
Sounds like an issue with the wifi router.
To check an fix the internet settings of the wifi router, you will need the adminstrative access/console/password for the router.
Then you can check that all new devices afre allowed to connect. On some routers you can restrict the access to a list of known devices or by enabling a MAC address filtering.
If you find such options on the HP wifi router, disable it and restart the wifi.
And make sure that the SSID of the wifi network is visible (= not hidden). Some Android devices have issue connecting to hidden networks.
Thread closed. Thank you.