Related
Made a huge error.....didnt go through forums and read instructions before trying to Flash a German T-Mobile MDA Compact to a English ROM....
The device is completely dead....
Followed all the steps required to get it back up...It is refusing to do so though....
Used this thread:
http://forum.xda-developers.com/viewtopic.php?t=19500
One thing to note is that I am not using the AC charger, am using the USB cable to charge the phone.
Can someone please helpme...
Haven't got past the bootloader mode...
If you followed the instructions from the other thread, it should have started flashing.
Some things to check on:
1) Did you do a full d2s before you attempted the upgrade? It's always good to have something to fall back on.
2) If you can get to a bootloader screen, all is definitely not lost.
3) Sometimes, it takes 4 or 5 minutes for the "Press to flash" comes up on the screen so be patient with that.
4) Make sure you did exactly a 416 byte copy from the original rom file in to the new flash file.
5) You can only write an nb1 file from the pc AFTER it has been created from the pocket pc. If the SD card has been pc formatted, the nb1 file will write to it but the pocket pc won't recognize it and will just sit there at the bootloader screen.
HTH
I think I fired the MDA
Well I did not create the nbf file from the ppc, downloaded it from the the forum FTP. I do not have the backup of the nbf file. As I mentioned I did not read the forums before trying the update.
I just downloaded the T-Mobile ROM update and tried installing it. Obivousioly it didn't work, Game the dreaded the 112 error in the 3rd step.
Am not even getting the bootlader screen now..
Any ideas on how I can get this device up and running.?...
ok, need some clarification here. "What" are you trying to load (nbf files or nb1 files) and how are you trying to load them (SD flash or the standard USB based upgrade)?
Easy enough to check to see if your device can still get to bootload mode....hold the camera and power switches in at the same time and hit soft reset with your stylus. After letting go of those and you see either "Serial" or "USB" at the top of the screen, you should still be able to recover from this.
Tried with the nb1 files not nbf (sorry abt teh error)..
The bootloader screen was showing up ...unitll I tried the T-Mobile MDAcompact_vers11201
After the 112 error while updating...the device now refusing to get to the bootloader mode.
Have I fried the device and made it unusable....?
hey just got back the bootloader screen...
Take the SD card out, disconnect the USB and tell me what happens when you hold the power and camera buttons in at the same time, then hit the soft reset.
Also, has the unit been charged recently?
Its showing Serial v1.00...after the reset.
Its been on the USB chatge all along.....
Great. If you get Serial at the top, this can be recovered.
If you want a good T-Mobile 1.12 rom file, go here and use this one:
ftp://ftp.xda-developers.com/Uploads/Magician/tmobile-uk_wwe_ROM_1.12.00(thereapermanl).rar
Unpack it and follow all the procedures about copying the 416 bytes, rewriting the file, etc. from the other thread. I have tested this rom file and it installs ok.
Thanks for the encouraging words...
Will it work even if I do not have a backup of the original ROM on my machine?....I only have the tmobile.nb1 file which I got from the XDA forums.
Lemme try using that and editing it.
Thanks a ton for your help.
You might be a little stuck for an nb1 flash if you don't have an original flash back up but don't fear. You can go here and get this WWE1.12 file and just do a USB type upgrade:
ftp://ftp.xda-developers.com/Magician/Shipped_ROMS/WWE_11200_128_11210_ship.exe
I know this one works too. It's ROM 1.12, Radio 1.12 and Ext_ROM 1.12. When you try to run the upgrade program though, it might give you a Country ID error. If so, use the attached upgrade program instead. If this one gives you a Country ID error again, close the program and just run it again. I've been down all these roads already.
Lemme get this right this time: I will be doing the following
1. Install the ROM as you have mentioned. With the country id hack if necessary
2. Hopefully by now the device would be alive. If so will take a backup of the ROM on the SD card
3. From then on follow the instruction given in the doc.
Hope I get it righ this time else Its going to be a long night for me.
Lemme know if I have to do anything else.
Either ROM will work fine for you. It just depends on whether or not you want I-Mate stuff on it or T-Mobile stuff on it.
Doing the USB upgrade will put the I-Mate ROM on but after that, it should be working and you can then do an SD backup, follow the SD flashing procedures and get the T-Mobile ROM on.
Good Luck!
The masupgrateut is throwing up a ruu.dll error?...you seen that one before?
What sort of error? Not found?
yup...
I extracted the ROM exe and found teh file...copied it to the windows folder..and ran the no id program...no error this time round but the update is still giving a COuntry ID error...
Been looking at various posts...specially this one...
http://forum.xda-developers.com/viewtopic.php?t=14973
Thinks thats gonna help?
ok...two things.....just run it again. The no ID program sometimes does that on the first time 'round so just run it again.
Second, stick this at the end of the RUU.conf file:
[CHECKCEID_TYPE]=1
ran the program multiple times...still getting the COuntry ID error...
Are you running this program? MaUpgradeUt_noID.exe
...with the change in the RUU.conf file?
I just noticed something....did you extract all the files to a single directory and just run it from there or did you just pull a few out?
ALL the files have to be in the same directory. This is also where you need to execute the installer program.
Hi All,
I am a complete newb with this stuff. I just bought the Tilt this weekend and a friend of mine told me i could swap out the interface....so i began my search and it lead me to this amazing site.
I really like the looks of L26_KaiserDiamond_V9 (new source!), but I don't want to brick my phone.
Can anyone give me a step-by-step quide into installing ROM's?
Many many thanks
Well first normally if you are going to ask about a specific rom you would post in the thread of the ROM. Secondly have you looked at the Wiki it has the step your asking for.
http://wiki.xda-developers.com/index.php?pagename=HTC_Kaiser#ROMx20.Upgrading
If i were you I would search and read before I post most of the time someone else has already asked what your looking for.
-McMex
Well, the instructions for flashing your first ROM are pretty straightforward:
1. Flash HardSPL
a. The first thing to do is to pick a ROM you want to flash,
and plug in your device to your computer.
b. The chef (person who makes the ROM) will usually say
which SPL he/she recommends. If he doesn't, you can just PM him.
c. Go to this page and pick the HardSPL that the chef recommends.
A HardSPL Security unlocks your phone, meaning that you can
flash different ROMs than the default shipped ROMs that come pre-installed on your phone.
d. Download the Kaiser-HardSPL-3.xx.zip from the above page and
extract them to a folder on your computer, for example: HardSPL.
e. Now download this (JumpSPLv1) and
extract it to a folder on your computer, for example: JumpSPL.
f. Once you have extracted the three files to a folder, open the folder,
and copy "kaiser_JumpSPL_pof_v1.nb" and "JumpSPL.exe" (no quotes) to
your device.
g. Power down your device, take out your SIM and SD card (if one),
then power back on the device. If it opens an emergency call screen
once restarting, just click the red End key button on your device to
exit and go to the today screen.
h. Open File Explorer, then open JumpSPL.exe on your device, select
the kaiser_JumpSPL_pof_v1.nb, then enter in: "0x00000000" no quotes.
i. Now, if done correctly, you should be at a Tri-color screen and
it should say "USB".
j. Now disable USB connections in Activesync/Windows Mobile Device
Center. To do this, click on settings under Activesync or Windows
Mobile Device Center (depending on if you're running Vista or XP) and
UNcheck "Allow USB connections"
k. Unplug your device, wait 5-20 seconds, then plug your device back in.
l. Remember that folder that you extracted the SPL to? Well, on your
computer, open that folder, then run KaiserCustomRUU.exe.
m. Click Next, Next, then Update. Wait for it to finish, then click Finish.
n. Congratulations! If done correctly, you should have HardSPL flashed
on your device. To confirm this, press and hold the camera button on your
device all the way while pushing the stylus into the reset hole. You should
be at a tri-clor screen (called the bootloader). The second line down should
say "SPL-versionhere.Hard" (no quotes). If it does, you're ready to flash!
If it doesn't, please re-read all instructions.2. Flash the ROM
a. Flashing the ROM is very easy. First, pick the ROM you like, and
download it. Usually ROMs are in a .zip or .exe file.
b. Once the download is finished, extract the .zip to a folder on your
computer. If it is an .exe, just run it.
c. If it was a .zip, just run KaiserCustomRUU.exe from the folder you
extracted the files to, click Next, Next, then Update, then Finish. It it
was an .exe that you downloaded, it should do this automatically. However,
if it doesn't, it should just extract the files for you into a folder. Just follow
the same procedure for a .zip file if it does do this.
d. NOTE: After you flash the ROM, when you get to the whole "Please tap the
screen to begin setting up your Windows-Mobile based device", hard reset by
holding down the two soft keys while pushing the stylus into the reset hole.
You should get to a white-colored screen. Just follow the directions on that
screen and then reboot. This fixes many issues, and is also known to make your
ROM perform at 100%.
e. Congratulations, you should have just flashed the ROM! If not, please
re-read the instructions above.3. Flash the Radio
a. This is where newcomers tend to become confused. Basically, you just need
a radio that matches the ROM you have. One reason to tell if you do not have
a correct radio is if you have camera issues, and sound issues while talking on
the phone. Just remember: only flash Kaiser radios! If you try flashing a Polaris
radio on your device, chances are you'll brick it.
b. You can flash the radio before or after you flash the ROM. Basically, the ROM
and the Radio just need to match. Chefs sometimes include Radios in their ROM,
in which case you would not need to flash a new one. Just look in the thread of
the ROM you want to flash to see if the chef included it. If there is an included
radio, you can skip the rest of the steps. If the chef does not include a radio,
he/she will usually recommend one.
c. You can download kaiser radios from here. Just download the
one your chef recommends. If your chef does NOT recommend a radio,
just PM him/her and ask which radio he/she recommends. Many
people prefer 1.58.25.17 for its awesome battery life. 1.58.25.17 also
works on many newer ROMs.
d. So, just for the sake of the rest of these steps, we are going to assume
that you have flashed a newer ROM and are now going to flash Radio 1.58.25.17.
e. Now, just download 1.58.25.17 from the link I posted above (should be a .zip),
extract the files to a folder on your computer, run KaiserCustomRUU.exe, click
Next, Next, Update, then Finish.
f. Congratulations, you have flashed your radio and you are completely done.
If, for example, you are experiencing issues with the camera and phone, just flash a
different radio using the same method as posted above.
That's it.
And remember, please read the Wiki, Stickies, and G.W.E.N.I. for the answers to most of your questions. Or, you could use the wonderful Search functions of this forum.
Hope this helps and good luck
Assistance required by a Guru.
USB + Power + active synch (MDC)
I’ve used
Herm Unlock v3
Magic Unlocker
CheetahUnlocker
They all run ok
I’m pretty sure the device is unlocked!
SD card is FAT32, CHEEIMG.nbh resides at the root.
Reset + left button
Rainbow screen appears
CHEE100
IPL-0.20
CHEE100
SPL-1.40.01iNex
And that is as far as It gets!!!!
it just sits there and does nothing can anyone assist ?
a011528 said:
Assistance required by a Guru.
And that is as far as It gets!!!!
it just sits there and does nothing can anyone assist ?
Click to expand...
Click to collapse
Actualy you should first understand that even if your Trëo is compatible with wm6.1 you must be sure that it is compatible with the rom that you are trying to install,
Next you should try to download the rom again so you can be sure that the rom you are trying to load is not corrupted...
and if all this is done you will probably need to try out the USBcable install mode!
Realy hope that you can solve your problem
[[]]
ROM, is the third different source (same version) to ensure no corruption.
USBcable install mode, can you provide any further details?
a011528 said:
ROM, is the third different source (same version) to ensure no corruption.
USBcable install mode, can you provide any further details?
Click to expand...
Click to collapse
strange that you can't install that, it's usually very simple and fast...
let me see if I understand, you are saying that you are trying to install the file when it is connected to your computer but the "cheeming" is on the SD card?!
If that's what you are doing just unplug the USB cable, you can't sync and use your SD at the same time... Just use the POWER cable and repeat all the process...
If that doesn't work for you, you should create a folder on your computer desktop and copy the "cheeming" to that folder, next copy whatever program you have used to change the SPL to that same folder.
Make a backup of the original files from your mobile, I hope you wont need them, but you should backup anyway...
then run the program and "cross your fingers"...
in about 5 or less minutes it should be done, and your treo should be runing your new WM6.1
This is the "risky" way, because you can "brick" your Treo, and I can assure you that it isn't easy to "unbrick"!
Hope you can do it with the SDcard method.
If I can help in any other way, please post or add on msn.
[email protected]
how i flash with usb
couple things to do. download a kaiser custom ruu. unrar or unzip your new rom you want to flash. best to have seperate folder to do this. rename the rom file to RUU_signed.nbh then run the kaiser ruu and follow the steps. very simple to do. make sure active sync is enabled before doing this.
Since the original link to this guide is buried in another thread, I've re-posted it here (and the guide in full) in order to help people that might've missed it. The latest version of the guide will always be available at http://www.karrderized.com/romguide/ however, and is a more printable version as well, so please check there too.
Installing the Hero ROM on your HTC Magic
Version 1.2 - 13 August 2009 - by KarrdeNZ
Disclaimer: I am not responsible if you brick your phone. This is only a guide. These instructions have worked for me, but there is no guarantee that they will for you as well. Follow this guide at your own risk.
Feel free to print off this guide if it makes things easier to follow. Please do not, however, steal this guide and claim it as your own. Updates to this guide will be posted here - http://www.karrderized.com/romguide/ - link, but don't steal. Thanks.
Things you'll need
Back up your settings
Installing the Android SDK
Determine your phone's version
Download the correct recovery ROM for your version
Download the correct Hero ROM for your version
Setting up the fastboot connection
Boot the recovery ROM
Back up your phone with Nandroid
Wipe your phone
Load your new ROM
Boot into your new ROM
Things to note
Acknowledgements
Changelog
1 . Things you'll need
A HTC Magic phone (obviously) running Cupcake (1.5) and with a SD card
A USB cable for your HTC Magic
A PC. These instructions assume you're running a Windows variant, though the same procedures can be performed on a Linux machine. Don't ask me about Macs. If you're running Windows, note whether you have a 32-bit or 64-bit OS, it becomes relevant later on.
The Android SDK - current release as of this writing is 1.5 Release 3, available here.
Recovery ROM - Which particular one you want to use will depend on your phone's version (I'll cover this later on).
A signed Hero ROM to install. Again, this is version dependent.
Got all that? Good.
2. Back up your settings
Now, before we start, back up. I'm of the opinion that you can never have too many backups. Take a copy of everything on your phone's SD card, make sure your contacts etc are synced, any apps you want that you can't easily get back from the Market are backed up, all that stuff.
Another thing you should note are the APN settings for your particular provider. These are in Settings, Wireless Controls, Mobile Networks, Access Point Names. You may have multiple APNs listed - go into each one and note down all the settings. You'll likely need to re-enter these manually once you've installed your new firmware.
Once you're satisfied you've got everything backed up, we can start setting up our environment.
3. Installing the Android SDK
Download the latest release of the Android SDK - here at the time of writing - for your relevant OS. I'll be using Windows from here on in. Extract the .ZIP file to somewhere convenient - I've got mine on my C: drive under C:\android-sdk-windows-1.5_r3. We need the SDK for the tools it provides in the tools subfolder, fastboot in particular, as well as the USB drivers for your phone.
4. Determine your phone's version
As of this writing, there are two distinct versions of the HTC Magic - PVT32A and PVT32B. The primary differences between these two versions is the amount of RAM (288MB on the 32A, 192MB on the 32B) and the radio (Qualcomm MSM7200a for the 32A, Qualcomm MSM7201a for the 32B). Generally, if your phone is HTC branded, it's a 32A, and if it's carrier branded (Google, Vodafone, etc) it's a 32B. Mine's a PVT32B from Vodafone NZ. But let's find out for sure what yours is.
Grab your phone and turn it off. Now, while holding the Back button down, power it back on. Your phone should now boot to a screen with a white background, some lines of text, and some skateboarding androids at the bottom. Welcome to fastboot.
The first few lines on the screen, in green, are what we're looking for. Mine reads as follows:
Code:
SAPPHIRE PVT 32B SHIP S-ON G
HBOOT-1.33.0004 (SAP10000)
CPLD-10
RADIO-2.22.19.26I
Apr 9 2009,23:30:40
Yours will likely differ slightly. The number we're looking for is in that very first line - PVT 32B in my case. Make a note of this. The next item we're looking for is the second line, which indicates your SPL version. Some SPL versions do not allow ROM flashing, notably those of T-Mobile's myTouch3G variant of the HTC Magic. At this writing, HBOOT-1.33.0006 and HBOOT-1.33.0010 are the two known "perfect SPL" versions that do not allow flashing. If you have either of those versions, stop now. There is a complicated procedure you will need to follow first.
Otherwise, for now you can turn your phone back off (by pressing MENU).
5. Download the correct recovery ROM for your version
Head to this thread and download the recovery ROM for your particular phone version, as we determined in step 4. Save it in the tools subdirectory of the Android SDK (in my case, C:\android-sdk-windows-1.5_r3\tools).
6. Download the correct Hero ROM for your version
If you have a 32A, this thread should help you find a signed ROM (I'd suggest Fatality's Hero ROM): here
If you have a 32B like me, try Qteknology's Hero port here- the swap version is the fastest Hero ROM I've found so far. It does however require you to repartition your SD card in order to provide swap space to speed the ROM up - a guide for this is available from the linked forum post.
Note I have only tested the one I linked for the 32B as that's the version I have. Download whichever ROM you need to somewhere handy, and rename it to update.zip. Please note: if you have file extension display turned off (default in XP) then just rename the file to update instead - the .zip extension will already be set. Once you've done this, copy it to the root directory of your phone's SD card. You can do this using the standard USB connection system that the phone provides, or if you prefer using a card reader.
7. Setting up the fastboot connection
Start your phone in fastboot mode as we did in step 4 (hold down Back while turning the phone on). Once the fastboot screen is up on the phone, plug the phone into your computer with the USB cable.
At this stage, my computer asked for drivers for the phone - these are included with the Android SDK, in the usb_driver subdirectory. Users with 32-bit versions of Windows should use the drivers in the x86 subdirectory under that, and 64-bit versions should use those in the amd64 subdirectory. Once the drivers have installed, leave the phone attached to your PC - you're ready to proceed with booting the recovery ROM.
[Guide] Installing the Hero Rom on your HTC Magic - part 2
8. Boot the recovery ROM
We're going to use the Android SDK's fastboot utility in combination with fastboot mode on the phone to perform a one-off boot of the recovery ROM so that we can back up the existing setup, wipe the phone and then load the new ROM. At this stage, it would be wise to make sure you've synced contacts and backed up whatever you want to hold onto.
Open a command prompt window on your PC (Start, Run, cmd) and change to the tools subdirectory of where you installed the Android SDK, for example:
Code:
cd\android-sdk-windows-1.5_r3\tools
The prompt should change to indicate you're now in that directory. Now we make sure the phone is properly configured to communicate through fastboot. Type the following:
Code:
fastboot devices
If you see your device listed, we're about ready to go. Let's boot into the recovery ROM:
Code:
fastboot boot recovery-RAv1.2.0G.img
If the recovery ROM you downloaded is named differently, substitute it's name for recovery-RAv1.2.0G.img.
All going well, your phone should kick into the recovery ROM now - you'll come to a pretty green texted menu with the HTC logo in the background. This ROM is being loaded via the fastboot software and is NOT on your phone, just in it's memory. We have yet to make any modifications to your phone at all.
9. Back up your phone with Nandroid
Let's make one more backup to be safe. The recovery ROM we booted into provides us with Nandroid backup and restore, which we can use to backup the firmware and data currently on the phone to the SD card.
On your phone, use the trackball to scroll down to Nandroid v2.2 backup and click. This will start the backup process, and you'll see some yellow text start to appear at the bottom of the phone's screen. Once it's complete, you have a backup.
Use the trackball to select the Reboot system now option and click. It should load back into it's normal firmware. You can now mount the SD card as usual and copy the nandroid directory from the SD card to your computer. This is also a prime opportunity to back up your entire SD card.
10. Wipe your phone
WARNING: This is the absolute LAST point at which you can back out of this procedure. After this, it's all or nothing. Proceed at your own risk.
Boot your phone back into fastboot with USB attached (see step 4) and then load the recovery ROM again:
Code:
fastboot boot recovery-RAv1.2.0G.img
Use the trackball to move down to Wipe data/factory reset. This will erase all the data on your phone, ready for you to install the new ROM. Click. Congratulations, you have just wiped your phone! You are now ready to load your new ROM.
11. Load your new ROM
Still in the recovery ROM menu, scroll to Apply sdcard:update.zip. This process extracts the ROM from the update.zip file we placed on your SD card earlier and installs it onto your phone. It may take a little while so be patient. It'll tell you when it's done.
12. Boot into your new ROM
Select the Reboot system now option and click. Your phone will now restart with it's shiny new ROM! First boots can take a while, so bear with it. You'll probably see a new splash screen or two on startup, and eventually you'll get into your phone. You may or may not be prompted with a request about giving an app root access on your first boot - you can safely Always Allow this, as it's writing a swap file to your SD card in an effort to speed things up. You'll also need to go through the setup process on the phone again as if it were new, because for all intents and purposes it is. This includes setting up your Google account syncing, as well as the new Hero functionality such as your Facebook, Flickr and Twitter integration (if you so desire).
And from here on out, it's all up to you! Enjoy your new firmware, make it your own. There's some great new functionality in Hero over the standard Magic firmware.
13. Things to note
This firmware isn't perfect. I'm loving it and see myself using it from here on in, but there are some quirks. These may or may not be fixed with your particular versions of ROM, especially once this guide has aged a little, but I'll try and keep it up to date.
The main thing you'll likely notice (especially if you're using a 32B like me) is the slowness. There's a lot going on with this new ROM so lag is fairly common. The phone will speed up a bit once you've used it some more, so bear with it. Your initial setups and playing around will be slow because of initial caching and your non-typical use of the phone, but this should clear up. Various ROMs have tried for workarounds for this, for example Qteknology's Hero port uses a swap partition on your SD card to help speed things up. CompCache is also a popular method, but my own experience with CompCache hasn't been very successful.
There are also reports of SMS messages sometimes not arriving on the latest Qteknology ROM - I mostly didn't experience this until recently, but it seems to be an occasional issue. The ROM builders are working hard on the issues they come across so fingers crossed for resolution on this one.
14. Acknowledgements
This guide wouldn't exist without the xda-developers forum. The bits and pieces I gathered from thereabouts are what I used to run this procedure on my phone, and hence build this guide. The people there are much more experts at this than I am, so I defer to their wisdom.
I must also give props to Jesse of Radix's Gadget Blog. His instructions were incredibly helpful in getting my head around what exactly to do.
And also to papalazarou, whose forum thread prompted me to write this guide.
- KarrdeNZ
15. Changelog
Version 1.2 - 13 August 2009
Added Changelog
Updated links and references to ROMs to account for new versions
Changed ROM recommendations to Qtek for 32B based on personal experience
Removed references to now fixed bugs, added reference to SMS bug on Qtek's ROM
Added "perfect SPL" note
Version 1.1 - 29 July 2009
Added note about update.zip naming with regard to file extensions
Added SD card issue
Version 1.0
Initial release
First rate stuff mate, thanks very much. Now all I need is the new release of Jerp's ROM and I'll be embarking upon my first upgrade. Makes so much difference having everything you need in one coherent place. This post really should be stickied.
+1 for sticky.
Needs to be in one place, will cut down on 'how do i' and 'where can i find' threads
(note i said cut down, and not cut out lol)
This applies to all roms actually.
Great write-up! Thx for the effort, this will surely be handy in all other topics, where these questions are asked again and again (logically IMHO, as it isn't basic stuff for everyone).
Well done!
Now that is a quality tutorial cheers!
+1 sticky
I had posted these replies elsewhere before I realised you had posted the guide in it's own thread. I've run into a problem and it's really confusing me as to why it's not working
---------------------------------------------------------------------
KarrdeNZ, mate I followed your guide to the letter. I got all the way down to step 11 and then a problem occurred.
When I clicked 'Apply sdcard:update.zip' it just said cannot find or cannot load update.zip, or something like that, then said operation aborted?
I was trying to install the EXACT same ROM as you, I downloaded it to my laptop, renamed it update.zip and moved it to the root of the SD card.
Yet it didn't work, I can't for the life of me think where it's gone wrong as everything else up to that point had gone smoothly.
Any idea's?
----------------------------------------------------------------------
Well I tried downloading the same file again. No luck this time either!
This is what it says when I click the install from sdcard button:
--install from sdcard...
Finding update package...
Opening update package...
E: Can't open /sdcard/update.zip
(no such file or directory)
Installation aborted.
Now I get that it's saying that it can't find the file but I really don't understand why? I mean the file is there, do I have to unzip the file onto my computer 1st and then put it on the sdcard?
I thought i just stuck the zipped file onto the root of the card making sure i renamed it 'update.zip'
Please help me out guys, thanks.
i did have the same issues, sorted it by:
Formatting the sd card (fat32)
Changing the permissions on the zip file
Moving files to the sdcard then sticking the sdcard into another computer to check that the files had been moved.
And it worked!
Roy_Drage said:
When I clicked 'Apply sdcard:update.zip' it just said cannot find or cannot load update.zip, or something like that, then said operation aborted?
I was trying to install the EXACT same ROM as you, I downloaded it to my laptop, renamed it update.zip and moved it to the root of the SD card.
Yet it didn't work, I can't for the life of me think where it's gone wrong as everything else up to that point had gone smoothly.
Any idea's?
Click to expand...
Click to collapse
don't know if this is the exact same error, but i had a similar situation and it freaked me out, all you have to do (in my situation) is wait a few seconds or so. i think the phone is still in the process of mounting the SD card or initializing the card component. give it a few seconds (30 sec) and try the update again.
I formatted the card in the phone before I started, did u format yours in the actual computer itself?
Also how do I change the permissions on the zip file?
n1ck75 said:
i did have the same issues, sorted it by:
Formatting the sd card (fat32)
Changing the permissions on the zip file
Moving files to the sdcard then sticking the sdcard into another computer to check that the files had been moved.
And it worked!
Click to expand...
Click to collapse
this is 5 star
thanx works gr8
Excellent guide. All the other tutorials/guides/instructions totally went over my head. Yours was extremely clear and easy to understand. Two thumbs up!
Excellent
Thank you for an excellent guide.
KarrdeNZ said:
I must also give props to Jesse of Radix's Gadget Blog. His instructions were incredibly helpful in getting my head around what exactly to do.
- KarrdeNZ
Click to expand...
Click to collapse
Sweet.. I get a mention! Glad my guide helped you get started and now you're writing a guide too to help others - this is what a community is all about!!!!
KarradeNZ - you've made a great start to a guide here - but I really think this should all be in the XDA Wiki so everyone can contribute/update/maintain it. Then we just get one link stickied at the top and everyone goes there..
I just started to write up a skeleton of what I think should be in the 'Ultimate Guide to Sapphire Hacking' on the Wiki page at:
XDADeveloperWiki - HTC_Sapphire_Hacking
You want to help me improve it?
Heck.. if you want we can use your guide as a basis if you like - I just braindumped what _I_ think should be in it and I can immediately see stuff I've overlooked that's in your guide!
Feel free to take inspiration/snippets/whatever from my guide for it - just throw a link to it in there as well. I prefer to keep the guide itself separate but am happy to have it contributing to the wiki.
And there's only one A in my name.
When I apply sdcard:update.zip I get the following Error
E:cant open/sdcard/update.zip
(No such file or directory)
installation aborted
Please help and suggest what could be wrong ?
Just rename the file update mate.
Then try again.
Thanks Roy_Drage for the fast reply you sorted my .zip problem.
Also well done and thanks to KarrdeNZ for putting such a great guide together that even a noob like me could follow. My new Magic is now running Hero looks awesome !
bajax said:
Thanks Roy_Drage for the fast reply you sorted my .zip problem.
Also well done and thanks to KarrdeNZ for putting such a great guide together that even a noob like me could follow. My new Magic is now running Hero looks awesome !
Click to expand...
Click to collapse
BT works? (can you connect to a BT headset?)
Facebook integration works?
have you notice any issues?
** PLEASE, READ THE GUIDE BEFORE FLASHING **
Flashing a device is a risky process, and you definitively have to know that your device might not boot correctly, or not boot at all. You must also notice that this method is being tested and some components of your Polaris will not working at the moment. Take into consideration that there are developers that are sharing all their work with us, but although they're really good at their job, they all have their lives. So, if something just doesn't work, please, be patient*
NAND Boot for Polaris! Made possible thanks to DZO!
This method will allow you to start Android without the need of Windows Mobile. It will just boot like if the device had a native Android OS installed onto it.
- You may see this guide really long, but it's because I tried to detail every step and I put lots of URLs to make the process easier for beginners It's not than difficult as it seems!
Step by step guide:
Needless to say that you need to have HardSPLed your device first!
1. CHOOSE YOUR ANDROID BUILD
You can install try to install any build from the Kaiser and Vogue forums. They should work for Polaris:
I personally recommend to start with Myn's Warm Donut Release 5.
You can choose it in two different screen resolutions
240x320 (my favorite) - http://download219.mediafire.com/t0lnxmijgEjg/1drm2jqwjzn/myn-WarmDonut-04-24-2010-240x320-110.zip
320x480 - http://download533.mediafire.com/ml1jxoyomIDg/miw2uzjjzjq/myn-WarmDonut-04-24-2010-320x480-160.zip
If you want more info, check its thread: http://forum.xda-developers.com/showthread.php?t=619980
Download the build. It may be a compressed file containing an androidinstall.tar.
Copy this androidinstall.tar under a folder named andboot at the top level of your SD Card. The file path should be /andboot/androidinstall.tar.
You're now ready to flash the OS loader.
2. -OPTIONAL, BUT RECOMMENDED. ERASE YOUR ROM.
To be sure that you won't have problems with the flashing, you should use a tool that executes the called Task 29 to clean the NAND memory in the device. This helps the flashing goes OK and minimizes the chance of a bad flash.*
Fortunately, there's such tool: It can be downloaded HERE (big thanks to leppa).
It's a hacked flashing tool. To make it work you will have to select a dummy .NBH file. Use the .NBH file you want, preferably a small one. You can use the one that you will download in step 3.
You it finishes the operation, your phone will NOT boot. Don't worry. This is normal. We will make it boot soon.
More info HERE: http://forum.xda-developers.com/showthread.php?p=6227425#post6227425
3. FLASH THE ANDROID OS LOADER TO NAND
You will need a .NBH in order to boot from NAND. It's usually named polaimg-panel[x]-[resolution]-[date].nbh.
I personally recommend to flash of the .NBH files by DZO dated 07-May-2010. They are listed on his site: http://it029000.massey.ac.nz/vogue/files/?C=M;O=D
Choose one according to your paneltype and resolution. Your paneltype depends on its maker. You should try from 1 to 3 to see which one works for you.
Flash the .nbh file you downloaded with your prefered tool (I used CustomRUU.exe for Windows).
To flash your device you might have to put your Polaris in bootloader mode. To enter this mode you have to do the following:
Press and hold the camera button.
Press reset while you hold the camera button. Release it (the reset button).
Hold the camera button until the colored bars screen appears.
If it doesn't work, remove the battery, wait for some seconds, put it back and try again.
When the colored screen (Hard SPL) is shown, you are ready to flash it using the flashing application (CustomRUU.exe, for example).
4. INSTALL YOUR BUILD
When you're done flashing, your device will boot. You will now attempt to install your build using the file androidinstall.tar.
You'll see lots of text lines scrolling while it boots. Now, pay close attention to the next step.
The system will prompt you to press and hold the center button of the DPad (in the middle of the jog-wheel) to start the Android Installer. It's a message like "Press x to launch the installer". Don't forget to hold it until the installer is shown!
The installer will eventually start.
A list of options should appear (in text mode). Use the jog-wheel up and down to navigate. D-pad center to select.
Choose your installation options (I selected System on NAND, Data on NAND). Don't choose any other option unless you know what you're doing.
Install it! (if it ask you to wipe the data, select yes).
Wait for the installer to finish.
The menu should appear again.
5. INSTALL THE SPECIFIC UPDATES FOR POLARIS
Due to particularities in our devices, some hardware like Wi-Fi and Bluetooth won't work properly if you don't apply some updates first.
You will need a file an androidupdate.tar to apply to the just installed system.
You can download it HERE (thanks to l1q1d).
When applied, the installer will be shown again.
You now have to select Fix permissions to avoid problems.
Don't exit the installer: soft reset your Polaris instead.
YOU ARE DONE! Your Android system will boot after some minutes.
Things that should WORK:
Phone calls: incoming/outcoming
Texting (SMS)
Data connection (GPRS/3G)
Wi-Fi
GPS
Bluetooth
Things that DON'T WORK:
USB Storage Mode
USB debugging is unstable.
Tethering
Camera (in Eclair)
Headset
Bugs/Issues:
Sometimes Wi-Fi hangs while is being disabled and prevents the device from suspending correctly (it won't sleep and the screen will turn of every time you press a button).
Data connection goes down from time to time and it won't reconnect until you go to the Modem application, disconnect, connect again and wait it to connect.
Audio Input: faulty and unusable with most of applications that use it.
* Enjoy and feel free to donate to our GREAT developers.
* I donated to our developers, and I'm from Spain. As everybody know, Spain is falling like a fainted Pokémon thanks to Zapatero (Mr. Bean II). If I can donate, how couldn't you do it?
I'm trying now.. Sorry my english...
They state that it's valid also for HARET:
if you're doing it with haret, extract basefiles to your sd, plop the androidinstall.tar into the same folder, and boot, hold down volume up just like the nand people (but don't pick nand to store the files, it won't work)
Click to expand...
Click to collapse
I've tried with the specified basefiles and plemen's Android 2.1, but I had no luck.
I noticed that when I press run from HARET and the progress bar fills up, it vibrates two times. Then, it seems that the device is hung, but after 15 seconds (or more), it boots. However, I didn't complete the rootfs-less setup process. It complaints about this:
Unable to open persistent property directory /data/property errno: 2
Click to expand...
Click to collapse
Anyone?
Wait, does this mean its totally an Android ROM? If so, COOL!
haven't tried yet ^^
Did you take the last package on sourceforge for the Eclair 2.1 Build? The files on Mediafire was corrupted.
I think there is no speed improvement with this, it's "only" an easier way to install and upgrade the system.
This is NOT "totally an Android ROM".
i can't install with this method
is there a "how to" or forum thread somewhere cause i get
sh: 2: unknown operand
losetup: /dev/block/loop1: No such file or directory
Failed
Failed to reach system.img on SD Card
Click to expand...
Click to collapse
during setup it complains "cant create folder /system cause file already exist"
i put basefiles at the root of my sd card and the vogue .tar in a folder call /andboot
all taken from here http://sourceforge.net/projects/androidhtc/
I think that you must flash a nbh that only works in vogue yet. I try to flash but it stop at 33%. I think that we must wait.
luzbel_es said:
I think that you must flash a nbh that only works in vogue yet. I try to flash but it stop at 33%. I think that we must wait.
Click to expand...
Click to collapse
Yeah, same problem. It's impossible to flash now with any package for Vogue or Kayser...
We have to wait for DZO's work to port .tar and . NBH for us...
Hi fellas:
I carried out research about the new boot up method, and it seems it will be compatible with our beloved Polaris. But it still needs some fine-tuning, first of all due to the fact that the new installer is started holding down VolUp, but this button isn't correctly recognized with the current bits.
In other words, we should wait before trying out this one. Vilord is aware of this issue.
Stay tuned!
Hi SuperJmn,
Of course I wait for ...
I look every day in the Vogue/Kaiser thread and hope we can to flash our Polaris next time.
Thanks.
Android should work much more faster after flashing... Can't wait to try this
manu33xtro said:
Hi SuperJmn,
Of course I wait for ...
I look every day in the Vogue/Kaiser thread and hope we can to flash our Polaris next time.
Thanks.
Click to expand...
Click to collapse
Hey
I have pola100 with pcar latest non-3d, Im trying my luck to get android started but with the latest files (img, rootfs, zImage) I am not able to. tried hell lot of combinations.
can you suggest me which one would I use, I downloaded some from sourceforge!
but I read that the new rootfs is for nand....
please friends guide me to right downlaods and versions for a near perfect android installation
Thanks in advance....
Niranjan
Hi! The new method is not only for NAND, but also for SD booting. It has some incompatibilities, so it's working for Vogue for the moment (Vogue owners are a bit more lucky than us in terms of development).
We are waiting for @vilord, @DZO and other authorities to fix the appropriate files.
I will contact them right after I end up writing this
Updated information for NAND boot. Thanks DZO!
Can you give us some feedback? Does it run better, smoothier than before? Or nothing about that?
it work but this resolution is not userful for me. No more speed than haret method, wifi and camera not work, system freeze some times. Do you have this problems?
How to put device in bootloader
Hello,
I've installed Android on my POLA100 (NAND method). Until now it's working fine. When I tried to put my device in bootloader mode, after installing Android, surprise... the combination (camera button pressed + stylus reset) isn't working.
If you used this: Eclair build you should download this update too: update for qvga and put androidupdate.tar from this archive on the andboot folder on your sdcard near androidinstall.tar.
After installing the system like SuperJMN said you'll have to press the power button one more after system reboot and choose update... from the menu,then quit when the menu reappear.
WIFI,Camera,Bluetooth doesn't work on this build(the only one I've tested with this new method)
Thank you SuperJMN for posting this,I hope it will remain for a long time on the front page and many thanks to DZO,VILORD,JAMEZELLE,PLEMEN and all other guys for the hard work.
Polaris
Hi,
for polaris you push power button, and boot menu works(NAND and SD).
The issue is that Wifi is not working now.
I try several builds.
So it seems not depending on the system?
Regards
How to put device in bootloader
Solved it. I put my device in bootloader by pressing the camera button + stylus reset when Android loads. I don't know if it worked because I removed my SD card and on the screen appeared "Waiting for SD card" but in that moment I've reset the device in bootloader.