Made a huge error.....didnt go through forums and read instructions before trying to Flash a German T-Mobile MDA Compact to a English ROM....
The device is completely dead....
Followed all the steps required to get it back up...It is refusing to do so though....
Used this thread:
http://forum.xda-developers.com/viewtopic.php?t=19500
One thing to note is that I am not using the AC charger, am using the USB cable to charge the phone.
Can someone please helpme...
Haven't got past the bootloader mode...
If you followed the instructions from the other thread, it should have started flashing.
Some things to check on:
1) Did you do a full d2s before you attempted the upgrade? It's always good to have something to fall back on.
2) If you can get to a bootloader screen, all is definitely not lost.
3) Sometimes, it takes 4 or 5 minutes for the "Press to flash" comes up on the screen so be patient with that.
4) Make sure you did exactly a 416 byte copy from the original rom file in to the new flash file.
5) You can only write an nb1 file from the pc AFTER it has been created from the pocket pc. If the SD card has been pc formatted, the nb1 file will write to it but the pocket pc won't recognize it and will just sit there at the bootloader screen.
HTH
I think I fired the MDA
Well I did not create the nbf file from the ppc, downloaded it from the the forum FTP. I do not have the backup of the nbf file. As I mentioned I did not read the forums before trying the update.
I just downloaded the T-Mobile ROM update and tried installing it. Obivousioly it didn't work, Game the dreaded the 112 error in the 3rd step.
Am not even getting the bootlader screen now..
Any ideas on how I can get this device up and running.?...
ok, need some clarification here. "What" are you trying to load (nbf files or nb1 files) and how are you trying to load them (SD flash or the standard USB based upgrade)?
Easy enough to check to see if your device can still get to bootload mode....hold the camera and power switches in at the same time and hit soft reset with your stylus. After letting go of those and you see either "Serial" or "USB" at the top of the screen, you should still be able to recover from this.
Tried with the nb1 files not nbf (sorry abt teh error)..
The bootloader screen was showing up ...unitll I tried the T-Mobile MDAcompact_vers11201
After the 112 error while updating...the device now refusing to get to the bootloader mode.
Have I fried the device and made it unusable....?
hey just got back the bootloader screen...
Take the SD card out, disconnect the USB and tell me what happens when you hold the power and camera buttons in at the same time, then hit the soft reset.
Also, has the unit been charged recently?
Its showing Serial v1.00...after the reset.
Its been on the USB chatge all along.....
Great. If you get Serial at the top, this can be recovered.
If you want a good T-Mobile 1.12 rom file, go here and use this one:
ftp://ftp.xda-developers.com/Uploads/Magician/tmobile-uk_wwe_ROM_1.12.00(thereapermanl).rar
Unpack it and follow all the procedures about copying the 416 bytes, rewriting the file, etc. from the other thread. I have tested this rom file and it installs ok.
Thanks for the encouraging words...
Will it work even if I do not have a backup of the original ROM on my machine?....I only have the tmobile.nb1 file which I got from the XDA forums.
Lemme try using that and editing it.
Thanks a ton for your help.
You might be a little stuck for an nb1 flash if you don't have an original flash back up but don't fear. You can go here and get this WWE1.12 file and just do a USB type upgrade:
ftp://ftp.xda-developers.com/Magician/Shipped_ROMS/WWE_11200_128_11210_ship.exe
I know this one works too. It's ROM 1.12, Radio 1.12 and Ext_ROM 1.12. When you try to run the upgrade program though, it might give you a Country ID error. If so, use the attached upgrade program instead. If this one gives you a Country ID error again, close the program and just run it again. I've been down all these roads already.
Lemme get this right this time: I will be doing the following
1. Install the ROM as you have mentioned. With the country id hack if necessary
2. Hopefully by now the device would be alive. If so will take a backup of the ROM on the SD card
3. From then on follow the instruction given in the doc.
Hope I get it righ this time else Its going to be a long night for me.
Lemme know if I have to do anything else.
Either ROM will work fine for you. It just depends on whether or not you want I-Mate stuff on it or T-Mobile stuff on it.
Doing the USB upgrade will put the I-Mate ROM on but after that, it should be working and you can then do an SD backup, follow the SD flashing procedures and get the T-Mobile ROM on.
Good Luck!
The masupgrateut is throwing up a ruu.dll error?...you seen that one before?
What sort of error? Not found?
yup...
I extracted the ROM exe and found teh file...copied it to the windows folder..and ran the no id program...no error this time round but the update is still giving a COuntry ID error...
Been looking at various posts...specially this one...
http://forum.xda-developers.com/viewtopic.php?t=14973
Thinks thats gonna help?
ok...two things.....just run it again. The no ID program sometimes does that on the first time 'round so just run it again.
Second, stick this at the end of the RUU.conf file:
[CHECKCEID_TYPE]=1
ran the program multiple times...still getting the COuntry ID error...
Are you running this program? MaUpgradeUt_noID.exe
...with the change in the RUU.conf file?
I just noticed something....did you extract all the files to a single directory and just run it from there or did you just pull a few out?
ALL the files have to be in the same directory. This is also where you need to execute the installer program.
Related
ive been trying to read up on everything but it seems that a lot of the information assumes i know at least a little about what im going to do. I really dont know anything and the tilt will be my first wm phone ever. i have never flashed a phone before but i would love to use duttys rom that i came across on this site, please tell me if these steps are correct for flashing my tilt before i go ahead and try it (dont wanna mess it up)
1. first i will do the hard-spl flash to allow flashing of the roms on my tilt- found at this thread http://forum.xda-developers.com/showthread.php?t=334679 seems easy enough
2. i download duttys hybrid build no. 4
3. it seems like the easiest way to flash my tilt is to do it from a micro sd card? i found these steps at this thread http://forum.xda-developers.com/showthread.php?t=332246
1. Get a 128MB MicroSD card (or whatever size you like) and format it (***please make sure you format it, but not just delete all contents on it)
2. find the ROM image you would like to use, normally namede RUU_Sign.nbh, and rename it to "KAISIMG.nbh"
3. Plug the card into the phone, then enter boot loader mode by pressing down the Power and Camera buttons simultaneously, and using the stylus at the same time to press the RESET button at the left side. Continue pressing the two buttons for a few seconds after pressing and releasing the reset button until the bootloader screen appears. (taken from Wiki)
4. You will first see a tri-color screen then the information on the card. Press power button to start flashing.
5. After all these are done, press the reset button located at the bottom of the phone to reset the device.
4. Is flashing the rom really as easy as these steps ^ make it seem to be? just put duttys RUU_sign.nbh renamed to KAISIMG.nbh on the formatted card, then do the reset instructions and follow the rest?
thank for the time and responses, sorry if there are more simplified instructions somewhere, but i hope i figured it all out before i try this.
I actually think the easiest way is through activesync, clicking on the executable that is usually given. but your first 2 steps is right.
ok so if i do 1 and 2
then i just put both files (the exe and the nbh on the phone) and run the exe from the phone? and thats it? lol
also what would you say the chances are of a total noob (like me) bricking a $400 phone...
EDIT: so i assume this: To Flash a ROM or Radio simply use a tool to convert the .nb files in to .nbh format Dutty's NBH tool works great! then copy pof's Kaiser Custom_RUU into the same folder and then run the Custom_RUU and your device will start the upgrade process. With the new RUU when you flash a splash screen or radio only your device will not hard reset!
i dont have to do the conversion for duttys because the files are already .nbh, correct?
You don't put the .exe and .nbh on the phone. Make sure you have an Active Sync connection to the phone, extract the files to your PC and run the .exe. The .exe goes through pre-checks to make sure your phone is ready to flash. Just make sure you have HardSPL on your device before doing anything. Should be straight forward.
Good luck.
ooo ok, i havent gotten the phone yet so i dont really have any thing to look at im just reading up on it, but that clears most/ if not all of my questions thanks a lot - both of you =)
Hi,
I'm sorry about this post but there seems to be an anormous amount of information which doesn't make a lot of sense to me.
All I want to do is upgrade my palm treo 750 from win5.0 to 6.1.
I've downloaded the rom but it doesn't upgarade. So I need to figure out a way to flash this phone so it can be upgraded to any roms.
I have tried the Cheetahunlocker which doens't work. It gets stuck on 0% then times out.
Could someone please give me some basic instructions on the best way to do this on the treo.
I've done this on the TYTN2 whith no issues however on this phone, it seems to be a lot harder.
Thanks in advance.
Your device needs to be unlocked. You can do this by calling ATT and getting unlock code or by using Magic_Unlocker.
search
Also you will need to have the HardSPL installed which is Step 1 only of the CheetahUnlocker
I just did it yesterday so I know it works.
After you get the phone unlocked, name the ROM .nbh file CHEEIMG.nbh and then put it on the SD card
The start the CheetahUnlocker process as it enters the HardSPL process it will go ahead and run the CHEEIMG file and flash your ROM
(it works ! ) DON"T CHANGE THE RADIO !!!!
After doing that be sure and reclaim your ROM space - search web for Removing Ext ROM and do that process, hard reset and you are ready to go
Takes about 15 min!
jcrompton said:
After you get the phone unlocked, name the ROM .nbh file CHEEIMG.nbh and then put it on the SD card
Click to expand...
Click to collapse
Thanks for your info.
sigh..
The rom is an exe file...
I downloaded 7-zip, extracted the rom to a folder.
Looking through it, I am unable find the ROM.nbh file!
CHEEMING.nbh is already there..
What am I doing wrong?
Thanks.
artii said:
Thanks for your info.
sigh..
The rom is an exe file...
I downloaded 7-zip, extracted the rom to a folder.
Looking through it, I am unable find the ROM.nbh file!
CHEEMING.nbh is already there..
What am I doing wrong?
Thanks.
Click to expand...
Click to collapse
Sorry I forgot it was already named CHEEIMG.nbh -- just use it like I said above.
Copy it to the SD card, put the SD card in the device and after you have used Magic_Unlocker , connect via Active Sync and start the CheetahUnlocker process. This will start the three step CheetahUnlock process (really all you need is step one which will put the HardSPL in place) as that process fails the CHEEIMG file on your SD card will get flashed.
Hope this makes sense
Bottom line is that you will be doing an SD flash of the CHEEIMG.nbh file but it takes HardSPL for that to work. Step one of the CheetahUnlocker installs HardSPL (that will be all you need of that process)
remember!
THE SD FLASHING METHOD TAKES A REALLY LONG TIME. SO LONG YOU MIGHT THINK IT'S BROKEN. BUT IT'S NOT!!!!
caps with bold and red= great way to emphasize an important point.
Thanks for the info but I'm still running into trouble.
I copied the file to the SDcard but when running the cheetahunlocker, it give the same error at 0% ( error 206) something about the connection..
I notice that active sync turns off when the cheetah unlocker goes to the coloured screen.
Edit:
Also, should I be moving the CHEEIMG.nbh or just copying it to the SD card?
Thanks.
artii said:
Thaks for the info but I'm still running into trouble.
I copied the file to the SDcard but when running the cheetahunlocker, it give the same error at 0% ( error 206) something about the connection..
I notice that active sync turns off when the cheetah unlocker goes to to the coloured screen.
Click to expand...
Click to collapse
Did you run the MagicUnlocker first?
Is the CHEEIMG.nbh file in the root of your SD card? Try re-formatiing your SD card (FAT32 important!) and then putting the CHEEIMG.nbh file in place on the root of the SD card.
After starting the CheetahUnlocker the TriColor screen should come on and then it should go to a standard White boot scan. It will ask if you want to flash and you will be asked to confirm by pushing the Power button.
If you can ever get Step One to complete on teh Cheetah Unlocker you should be able to confirm that the HardSPL is installed by turing off Today screen (Red, end button) , then hold the left side button while then pushing the reset button. You will get a tricolor screen that lists your SPL version. If it is HardSPL on an unlocked device and there is a CHEEIMG.nbh file on an inserted SD card it will then automatically go to a White boot screen .....
If any of this sounds foreign to you then you need to familiarize yourself in the Wiki re SD flashing
PS do you have the NetFramework 2.0 installed on your PC? When you start the CheetahUnlocker are you getting the Treo device confirmation to install the 2 boot exe files that let the Treo go to the boot screen (you have to answer yes to both of these) - are you making it that far?
Yes I ran the unlocker which worked fine.
I formatted the SD card, copied the CHEEMING.NBH to it so it's the only file there.
No I run the CheetahUnlocker.exe , yes to disclaimer , then STEP 1 - I click FLASH SPL, then next, next etc.. I hit Update - next - next then the phone msg comes up asking if I want to run jumpSPL.exe - I hit yes and it goes to the tri colour screen, the active sync dissapears, the screen on the pc stays at 0% and then I get the error 260: Connection, check cable etc..
How is it suppoed to maintain a connection when Active sync turns off?
I did check and framework2.0 is present.
Thanks.
artii said:
Yes I ran the unlocker which worked fine.
I formatted the SD card, copied the CHEEMING.NBH to it so it's the only file there.
No I run the CheetahUnlocker.exe , yes to disclaimer , then STEP 1 - I click FLASH SPL, then next, next etc.. I hit Update - next - next then the phone msg comes up asking if I want to run jumpSPL.exe - I hit yes and it goes to the tri colour screen, the active sync dissapears, the screen on the pc stays at 0% and then I get the error 260: Connection, check cable etc..
How is it suppoed to maintain a connection when Active sync turns off?
I did check and framework2.0 is present.
Thanks.
Click to expand...
Click to collapse
I'm not sure exactly what is happening in your case but I do know that once a device of any kind enters the bootloader - Active Sync dies - AS is part of the OS and that no longer exists after the bootloader starts, I.e. Windows Mobile isn't really running any longer. the AS connection just gets it started.
I'm not too sure either.
I've unlocked the phone which worked fine.
When I run the cheetahunlocker, it doensn't get past the first step.
Should I be running Hardspl first?
What rom works best with the Treo 750? Link please!!!
What rom are you wanting to use? I have Treo750_WM6.1_WWE_Lite, looking for a more stable rom. Please list some or link them.
I tried both roms
the lite one and the normal one. I must say that the normal one is more stable - with the lite I had to do a reset at least one per day. with the normal version I did not do a reset at all...
Hi, did you resolve this CONNECTION issue? I'm having exactly the same problem.
Anyone?
hey everyone... i have a problem similar to these i think. I'll explain
i've done the magic_unlocker and i can do the 1st step of the cheetahunlocker. treo reset automatically and when i try to flash the rom the trilinear screen doesn't change to the blue screen which is the screen of the rom flash
anybody now why?
i have cracked my head the hole day and a still can't do it :S
artii said:
Yes I ran the unlocker which worked fine.
I formatted the SD card, copied the CHEEMING.NBH to it so it's the only file there.
No I run the CheetahUnlocker.exe , yes to disclaimer , then STEP 1 - I click FLASH SPL, then next, next etc.. I hit Update - next - next then the phone msg comes up asking if I want to run jumpSPL.exe - I hit yes and it goes to the tri colour screen, the active sync dissapears, the screen on the pc stays at 0% and then I get the error 260: Connection, check cable etc..
How is it suppoed to maintain a connection when Active sync turns off?
I did check and framework2.0 is present.
Thanks.
Click to expand...
Click to collapse
If it goes into the bootloader then you should be good to go. Both 750s i unlocked did this. However, if done correctly, the phone should go to a light blue screen where you will press the power button and flashing should begin.
na1kkkk said:
hey everyone... i have a problem similar to these i think. I'll explain
i've done the magic_unlocker and i can do the 1st step of the cheetahunlocker. treo reset automatically and when i try to flash the rom the trilinear screen doesn't change to the blue screen which is the screen of the rom flash
anybody now why?
i have cracked my head the hole day and a still can't do it :S
Click to expand...
Click to collapse
Are you doing the SD method or Desktop? DO the SD method and it should begin flashing right away after the 1st step of cheetahunlocker.
Assistance required by a Guru.
USB + Power + active synch (MDC)
I’ve used
Herm Unlock v3
Magic Unlocker
CheetahUnlocker
They all run ok
I’m pretty sure the device is unlocked!
SD card is FAT32, CHEEIMG.nbh resides at the root.
Reset + left button
Rainbow screen appears
CHEE100
IPL-0.20
CHEE100
SPL-1.40.01iNex
And that is as far as It gets!!!!
it just sits there and does nothing can anyone assist ?
a011528 said:
Assistance required by a Guru.
And that is as far as It gets!!!!
it just sits there and does nothing can anyone assist ?
Click to expand...
Click to collapse
Actualy you should first understand that even if your Trëo is compatible with wm6.1 you must be sure that it is compatible with the rom that you are trying to install,
Next you should try to download the rom again so you can be sure that the rom you are trying to load is not corrupted...
and if all this is done you will probably need to try out the USBcable install mode!
Realy hope that you can solve your problem
[[]]
ROM, is the third different source (same version) to ensure no corruption.
USBcable install mode, can you provide any further details?
a011528 said:
ROM, is the third different source (same version) to ensure no corruption.
USBcable install mode, can you provide any further details?
Click to expand...
Click to collapse
strange that you can't install that, it's usually very simple and fast...
let me see if I understand, you are saying that you are trying to install the file when it is connected to your computer but the "cheeming" is on the SD card?!
If that's what you are doing just unplug the USB cable, you can't sync and use your SD at the same time... Just use the POWER cable and repeat all the process...
If that doesn't work for you, you should create a folder on your computer desktop and copy the "cheeming" to that folder, next copy whatever program you have used to change the SPL to that same folder.
Make a backup of the original files from your mobile, I hope you wont need them, but you should backup anyway...
then run the program and "cross your fingers"...
in about 5 or less minutes it should be done, and your treo should be runing your new WM6.1
This is the "risky" way, because you can "brick" your Treo, and I can assure you that it isn't easy to "unbrick"!
Hope you can do it with the SDcard method.
If I can help in any other way, please post or add on msn.
[email protected]
how i flash with usb
couple things to do. download a kaiser custom ruu. unrar or unzip your new rom you want to flash. best to have seperate folder to do this. rename the rom file to RUU_signed.nbh then run the kaiser ruu and follow the steps. very simple to do. make sure active sync is enabled before doing this.
Hello Friends.
My English is not very good but let me indicate the beginning'll try to explain.
I bought the device from last year's TR TURKCELL un rom convert was 6.5.
My job, I had to return 6.5 to 6.1 sees. I tried to go back a lot of things but I think the name of the error RUU_signed.nbh file with the name change CHEEIMG.nbh want to install after the following issue has occurred.
How do I do if I've stayed if the bootloader. Now red, green, blue and white colors on the screen there. When a screen comes up gray. when I press the camera, restart button does bootloder screen.
On Screen
Palm TR
IPL-0.20
Palm TR
SPL-0.24 0000
Writes...
USB and PC hardware in the device is visible. Can not connect to the bootloader in the Active SYNC.
I researched the Internet to the device I need to take the original rom. A lot like the original Treo750_Cingular_ROM called Treo750_2.23_ROW_WM6 ROM file I tried did not take. As enhancements on a PC via USB, but does not do installation DesktopUpdater. I tried with SD card, makes installation , BOOT Ok GSM gives OK, but gives FAİL Errors on OS install. At the end of the installation gives the error bar. I'm normal with FAT32 formatted SD was snow. SD card would install the original file 1.16RWE_CHEEIMG.nbh. camera, I would hold the restart button. to install the device, while 1% is automatically rebooted. I also want to install the self-RADIO reboot is 7%.
As far as I understand with; device when large files at 1% at small-sized files when closing at 7% has been reopened
devicereset, Hard-SPL, Treo750_OS5_2_19199WWE_STD, Original 1.16RWE.nbh, Treo750_2_23_ROW_DE_DesktopUpdater, completefixed, I tried almost everything, but the installation does not do..
I need this device too. I am electronics technician. Heard called JTAG recovery method.
Luckily the apology, that I am open for any ideas. but you'll help me. Tek Tek at a descriptive writer, you'll be happy. I trust you. As of this minute to thank every one, wish to express my respect and greetings
Based on your bootloader screen you have not successfully HardSPL'd your Treo. You need to do that first, and then flashing ROMs with the SD card is possible. You can't flash a ROM using the SD card without doing this.
You also can't downgrade a ROM using the regular installation packages because the install package will see the current ROM (if I understand you correctly, WM6.5) is a newer ROM than what you are trying to install. I think I remember seeing a post someplace where you can edit one of the files in the installer package to get it to work, but you would have to search to find it and even so, it's probably much more difficult to do than just doing the Hard SPL.
I have a My Touch 4G currently running 2.3.4 that I want to downgrade to 2.2.1 so I can root it. I am unable to get it to take the PD15IMG.zip to take once I hit the bootloader. It says its extracting fine, but the phone never reboots and if I manual reboot it, it boots up on 2.3.4.
I was using the following instructions.. cyanomod instructions and I did everything fine but get stuck with step 8.
Here is a copy of my ABD session:
Open to any suggestions.. I did some searches but no luck.
I tried to paste the URLs for the pastebin and the instructions I used but was blocked because of the stupid spam rules for newbies.. so PM me and ill send them to you.
Also as you can see I have been a member for over a year now, I just do a lot of lurker so I don't post much. I usually can find my answer searching without asking but I am stumped on this one.
This exact same thing happened to me.
The problem was that ADB wasn't pushing the entire PD15IMG file to the SD card. Every time I tried it it was missing exactly 53 bytes. (You can check this by looking at the file size of the PD15IMG on your hard drive and see if it file size matched EXACTLY on your SD card down to the single byte.)
I fixed it my using the file manager on my computer to just drag and drop the PD15IMG file onto the SD card. For some reason that transferred the entire file without problem.
I ran through the steps again and viola, 2.2.1 upon reboot.
You might also have a corrupted PD15IMG file. You can fix that by re-downloading the file, preferably from a different source just in case.
why u need downgrade 2.2.1 ?
@skipjacks - ill try that, on the 2nd attempt at it yesterday I manually copied of the file over after I downloaded it from another source, yet it still would not upgrade. I will give it a 3rd shot and report back.
@Ridofu - I am tried of having the HTC offical software crashing on me. I would like to root and then install CM7.1
Same thing..
I downloaded PD15IMG.zip manually over the HTC E:\ drive I have mounted.. did all the commands again, went to bootloader, it says it installs but then never reboots or does anything...
the image say loading, and I see a blue bar on the right top corner... then it switches to checking with a yellow/orange bar in the right top corner..
then it just goes back to the main screen and doesn't do anything..
all i see is fastboot, recover, factory reset, simlock, image crc
Id love to run the adb shell md4sum /sdcard/PD15IMG.zip but everytime I run it it comes back with md5sum: not found
Any ideas?
How I rooted my MT4G
Try this guide:
http://androidrootking.blogspot.com/2011/10/how-to-root-your-mytouch-4g-original_12.html
This is a step-by-step guide to root your MT4G. It has a link to another guide that will help you downgrade your phone.
You must downgrade FIRST, in order to root, because the root tool (gfree) DOES NOT WORK with Android 2.3, it only works with 2.1.
If you really like GingerBread, and want to keep root, go here AFTER you're rooted:
http://forum.xda-developers.com/showthread.php?t=1264704
—E!
Do you have MicroSD card reader in/for your PC?
Try to use it instead of copying the file through the phone.
@Ericm301 that is the exact method I have followed and it does not work. I have done the Push method, I have done the copy via USB cable to the E:\ drive that is mounted and neither allow me go to bootloader and load the file.
@Jack_R1 I will try getting a Micro usb adapter and copying the file over as well.
I tried taking the SD card and copying the file manually, I also tried to use the file from a 3rd source. It will not downgrade. I can post a video if you want to see it fail.
Just wanted to give a update. I did the manual downgrade 2 or 3 more times and I finally gave up on it.. then I switched to Fastboot Downgrade method and it worked perfectly the 1st time..
man what a frustration!