Related
So today I was trying to updated to the latest Continuum and after i flashed it it was acting wonky. I hadn't reverted to stock in a while so i thought.. might as well.
So here is what i did
1.) odin 1 click to stock
2.) whenever i flash back to stock i lose 3 button combos. I thought well, i could try to fix it, or i can just flash the GB bootloaders which have it anyway so:
3.) adb reboot download
4.) odin flash GB bootloaders as PDA
5.) very shortly thereafter odin failed and phone rebooted
6.) stuck with Phone ..!.. PC
I have tried every possible key combination known to man. 2 button, 3 button, combinations of holding and releasing buttons plugging in usb taking out the battery, etc etc.
I even went out and made a jig. I have tried both 300k resistor to directly to the mini usb pcb and made a little usb jack with 300k attached. (i also tried 301, 302 and 303).
All of these boot the phone but go directly to phone ..!.. pc.
The only thing i'm not sure of is if the jig is actually 300k, i don't have a potentiometer to test it. The pack of radioshack resistors i bought though did have 5 in it, so i tried various combos of them in-case one was flak.
Is there anything i didn't think of yet? I'll try to take my jig to a potentiometer on tomorrow (work is conveniently located on the way to the ATT store) and if all else fails i'll take it to att and see what they can do.
Is there anything i haven't tried that i should? Any ideas?
Thanks in advance
You arent bricked with that screen.
Try power and vol down.
Failing that, take batt out, plug in usb, then batt.
Still doesnt work?
Buy, or make a proper (tested) jig.
If you power the phone off then connect your jig, and all it does is try to boot the phone as normal then you have an improper resistance. You are most likely changing the resistance when you hold the jig with your fingers. Try holding it with gloves on or something, or order a microusb breakout board to solder your resistors on to.
modest_mandroid said:
If you power the phone off then connect your jig, and all it does is try to boot the phone as normal then you have an improper resistance. You are most likely changing the resistance when you hold the jig with your fingers.
Click to expand...
Click to collapse
This
Duck tape where your fingers are gonna touch.
Well. I was masking it with scotch tape like i saw in an example. I rebuilt the jig with 3x100 and 1x1 and wrapped it in duct tape. still boots to Phone ..!.. PC. I'll get to a potentiometer tomorrow and make sure it's got the right rating.
I also ordered a real jig, but it won't be here for days.
So.. is there anyone out there who has gotten the Phone ..!.. PC screen and _not_ been able to recover from it?
SirFunk said:
Well. I was masking it with scotch tape like i saw in an example. I rebuilt the jig with 3x100 and 1x1 and wrapped it in duct tape. still boots to Phone ..!.. PC. I'll get to a potentiometer tomorrow and make sure it's got the right rating.
I also ordered a real jig, but it won't be here for days.
So.. is there anyone out there who has gotten the Phone ..!.. PC screen and _not_ been able to recover from it?
Click to expand...
Click to collapse
Highly doubtful.. that's the "**** your pants when you first see it" screen but everyone manages to recover from it eventually, unless they have some sort of hardware problem.
SirFunk said:
I rebuilt the jig with 3x100 and 1x1 and
Click to expand...
Click to collapse
whoh... you are missing some "K" in there you got Kohms right?
TRusselo said:
whoh... you are missing some "K" in there you got Kohms right?
Click to expand...
Click to collapse
Haha, yes. I was just typing fast. They are the same 100k and 1k ohm resistors most of the tutorials i've seen get from radioshack
http://forum.xda-developers.com/showthread.php?p=13482176#post13482176
make sure your tape is covering the jig completely. Even the tiniest amount of contact will interrupt the resistance.
Speaking of bricking, mine wont turn on at all, its ****ing dead. bought a JIG and ill wait for it to come and try my luck, buy a new one if not. Good luck bro
So, I brought my jig in to work today and tested it with a volt meter. When setup with 3x100k and 2x1k it read as 301k. i taped it securely with duct tape and tested it again, still 301k. Tried it out a few times... phone ..!.. pc screen.
I brought it into AT&T and they set up a warranty service for it. Lets hope it goes off with out a hitch. Just for grins and giggles. I'll keep my homemade jig and when i get my new phone i'll try it out. My guess is it will work. I think in the bootloader flashing fail it wrote some of the bootloader but not the whole thing or something like that.
So, I brought my jig in to work today and tested it with a volt meter. When setup with 3x100k and 2x1k it read as 301k. i taped it securely with duct tape and tested it again, still 301k. Tried it out a few times... phone ..!.. pc screen.
I brought it into AT&T and they set up a warranty service for it. Lets hope it goes off with out a hitch. Just for grins and giggles. I'll keep my homemade jig and when i get my new phone i'll try it out. My guess is it will work. I think in the bootloader flashing fail it wrote some of the bootloader but not the whole thing or something like that.
Click to expand...
Click to collapse
Sorry to say but you are mistaken. If it were ANY problem with a bootloader you would have gotten nothing out of your phone, nothing. At all. Not a single thing.
was your phone on that screen while you were trying the jig? It has to be powered off to work. If it was off How long did you try? It can be tricky to get it just right on the pins.
It's cool you're getting it replaced I guess but a jig would have worked. I can guarantee that.
The phone was definitely off when i was using the jig. It would then boot to that screen. I tried it about 15 times. Both with my mini-usb adapter i made and by just touching the resistors to the pcb in the mini-usb connector.
I guess i'll know in a couple days when i get a new phone if my jig works or not. I also orderd a pre-made jig for future problems.
I wish i could say it was just user error on my part, but i think something was truly messed up. I read something on another thread about some stock rom doesn't have a way to get into download mode? (keys or jig -- only adb i guess?) maybe that's what i flashed initially?
A jig will always work unless it's actually a brick, or your usb port is broken. Sometimes the button combo is lost yes. And, adb only works if you can get to the OS.
I'm aware that ADB only works from the OS. Generally after flashing this stock rom, i had to boot into OS and ADB to get to download mode (buttons never worked). I never tried a jig before though.
I actually think that the jig I ordered may be here before my new phone. Either way, I'll hang on to the old phone until my jig comes and then i'll try a commercial jig.
Perhaps i'm the first person with a 'soft-brick' that is actually a 'hard-brick'? *shrug*
SirFunk said:
Perhaps i'm the first person with a 'soft-brick' that is actually a 'hard-brick'? *shrug*
Click to expand...
Click to collapse
If so you are super duper amazingly unlucky!!
I've heard of 2 accounts of a hard brick, one was a problem with the param.lfs, but one was actually a bootloader mix brick, that have been recovered from by a jig.
What they did was:
Pull battery
Insert battery DON'T TOUCH ANY BUTTONS
Insert jig.
Hold volume buttons.
That booted them into download mode and saved their phones.
Those are odd accounts but your phone isn't that damaged in comparison. That being said anything is possible, but I'd put money down the jig will work. The only reason it wouldn't is like I said, if your usb port is broken.
If you think its completely bricked, ill buy it for $10
just pm me
Are you placing the ponds of the jig on the 2 correct usb pins (i think it is five and six).
mrhaley30705 said:
Are you placing the ponds of the jig on the 2 correct usb pins (i think it is five and six).
Click to expand...
Click to collapse
Pretty sure it's 4+5 (there are only 5? Either way it's the 2 closest to the audio jack... so yes.
SirFunk said:
Pretty sure it's 4+5 (there are only 5? Either way it's the 2 closest to the audio jack... so yes.
Click to expand...
Click to collapse
Have you tried cutting up a micro usb cable tip and then trying it? I had the same problem with mine. Couldn't get the jig to work until this method.
I've read.. really I have..
Oden's
3 button fix
using linux..
using android sdk and the adb commands..
I haven't tried the JIG yet.
But I wanted to show you guys first before I leave work for the day and stop and Radio Shack on my way home.
I can't get into the Download Mode. When i power on the phone normally I get the AT&T "World Phone" screen. white with blue AT&T logo
If I hold down the Vol down or both down and up and plug in the usb cable from my pc to the captivate i get THIS!!??
So It's not hardware bricked (I don't think)... but what do I do?!
I can't get any of the one click loaders to see the phone, it doesn't ever get into a recognizable mode.
What happened:
I had CyanogenMod 7.1.. I wanted to see what MIUI was all about. Then I wanted to go back.. I went into recovery and formatted EVERYTHING i could find, factory reset, and now I have this non-animated waiting animation.
I figured I could flash back to factory and clean the phone then flash with CWM to CM7.1... I WAS WRONG!!!!!
Jig should get you where you need to be. Looks like you lost your button combos. What is your build number and which bootloaders are you using?
the only info i have left is the inside label.
Samsung
Model: SGH-i897
FCC ID: A3LSGHI897
IMEI: not telling
S/N: R1XZA58158D
1010 REV 0.4
SKU: 65187
1010 is your build number. 2010 October.
But.... I still need to use a JIG? No way of fixing this with software?
I hate to say it, but probably not. In formatting "everything", it seems like you've formatted out the software parts that would allow you to get back to where you could use software to fix this. A jig will get you to download mode, as it's a hardware-based solution.
Would a quick stop at the local AT&T store help any? Can they do a factory reset with their equipment? The only advantage i see is that they might do it for FREE and I wouldn't need to fudge around with the stupid resistors?
DO NOT USE 3button fix! DONT EVER. you will hard-brick for real if you have gingerbread bootloaders before flashing 3 button fix. 3 button fix is obsolete. to fix (if needed) use the i897 ginegerbread bootloaders to get 3 button fix and get gingerbread ready at the same time without bricking. if you cant find the thread [MOD] i897 Gingerbread Bootloaders, you shouldnt be flashing ANYTHING from this site,
that being said.\
take out battery,
put in battery,
HOLD both volume buttons,
PLUG IN USB TO PHONE/PC
KEEP BUTTONS HELD UNTIL YOU SEE YELLOW TRIANGLE
it works, trust me.
---------- Post added at 01:43 PM ---------- Previous post was at 01:41 PM ----------
Att store does not and will not re-flash the software on your phone, if you even let them see it they will know you VOIDED YOUR WARRANTY. dont ask questions like that. we will KNOW you havent read a damn thing on this site.
Looks like the PARAMS partition was damaged on your device. Your PARAMS can be configured to boot the phone to any mode. it's the BOOT_MODE parameter I think. Using this simple string value you can tell your device to boot into charging, normal, download, recovery and several others which I have no clue about.
Looks like your device has valid bootloaders, but the kernel has been instructed to boot into charging mode. It won't finish charging mode because the qualifications are not met.
I'm betting that since you obviously have a valid PBL, and SBL, you can plug that into the stock charger outlet and have the kernel boot into battery charging mode, then turn it on normally. But definately reflash your params.
TRusselo said:
DO NOT USE 3button fix! DONT EVER. you will hard-brick for real if you have gingerbread bootloaders before flashing 3 button fix. 3 button fix is obsolete. to fix (if needed) use the i897 ginegerbread bootloaders to get 3 button fix and get gingerbread ready at the same time without bricking. if you cant find the thread [MOD] i897 Gingerbread Bootloaders, you shouldnt be flashing ANYTHING from this site,
that being said.\
take out battery,
put in battery,
HOLD both volume buttons,
PLUG IN USB TO PHONE/PC
KEEP BUTTONS HELD UNTIL YOU SEE YELLOW TRIANGLE
it works, trust me.
---------- Post added at 01:43 PM ---------- Previous post was at 01:41 PM ----------
Att store does not and will not re-flash the software on your phone, if you even let them see it they will know you VOIDED YOUR WARRANTY. dont ask questions like that. we will KNOW you havent read a damn thing on this site.
Click to expand...
Click to collapse
Also a link to i897gb bootloaders in my sig
TRusselo said:
dont ask questions like that. we will KNOW you havent read a damn thing on this site.
Click to expand...
Click to collapse
First off.. Mind your manners and respect the forum for what it is. A place for all of us to learn and expand our knowledge on these awesome devices
Second off, you joined this forum a few months ago.. I've been here since 2005.. so please don't assume that I haven't read a "damn thing on this site" or that I haven't contributed to the site either! This is not the first time I've rooted or flashed or recovered from a bricked phone before. It's not even the first time on a Captivate. also, I've been reading since 9am.
I'm in real good with my AT&T guys so no need to worry about voiding anything. They already know and they have asked me to root their phones as well. They also offered me a job but they can't afford me.
So... the question wasn't "will they know I voided my warranty" or "do they flash".. the question was, "Can they do a factory reset with their equipment" which I admit should have been worded, Can they get me into download mode with their equipment?
Thank you for the information regarding the 3 button fix being obsolete. I wasn't planning on flashing it but good info anyway.
"take out battery, put in battery, HOLD both volume buttons, PLUG IN USB TO PHONE/PC, KEEP BUTTONS HELD UNTIL YOU SEE YELLOW TRIANGLE, it works, trust me." = doesn't work.. that's why I'm posting.
I held the buttons for over 60 seconds (thumb goes numb after that) and I also tried Just the Vol Down button.. Same results as picture attached in the first post of this thread.
so yeaaaaaaa... i stopped off at radio shack on the way home and got the resistors to make the jig.. aaaaaaaaaaaand it didn't work.
I was successfully able to get the jig to touch just the first 2 pins next to the head phones jack and i got the exact same non-animated animation circle.
SOOOooooo i'm starting to look into the fact that I still have insurance on my line
Buy a jig instead if making one. They are less than $10
Edit
Did you try plugging in to Odin after using your home made jig? Also, make sure to wrap the jig in tape so your fingers aren't in contact with any of the jig. Contact with the jig can change the resistance, rendering it useless.
SlyDogJeff77 said:
First off.. Mind your manners and respect the forum for what it is. A place for all of us to learn and expand our knowledge on these awesome devices
Second off, you joined this forum a few months ago.. I've been here since 2005.. so please don't assume that I haven't read a "damn thing on this site" or that I haven't contributed to the site either! This is not the first time I've rooted or flashed or recovered from a bricked phone before. It's not even the first time on a Captivate. also, I've been reading since 9am.
I'm in real good with my AT&T guys so no need to worry about voiding anything. They already know and they have asked me to root their phones as well. They also offered me a job but they can't afford me.
So... the question wasn't "will they know I voided my warranty" or "do they flash".. the question was, "Can they do a factory reset with their equipment" which I admit should have been worded, Can they get me into download mode with their equipment?
Thank you for the information regarding the 3 button fix being obsolete. I wasn't planning on flashing it but good info anyway.
"take out battery, put in battery, HOLD both volume buttons, PLUG IN USB TO PHONE/PC, KEEP BUTTONS HELD UNTIL YOU SEE YELLOW TRIANGLE, it works, trust me." = doesn't work.. that's why I'm posting.
I held the buttons for over 60 seconds (thumb goes numb after that) and I also tried Just the Vol Down button.. Same results as picture attached in the first post of this thread.
Click to expand...
Click to collapse
Try the steps he told you again, but flip flop putting in the battery, and plugging in usb... i.e. plug phone into usb, hold both volume buttons, THEN insert battery. instant download mode. worked every time for every build number captivate i've ever tried.
that didn't work either..
I just bought: 'SainSmart Micro USB Dongle Jig for Samsung Galaxy S Captivate / Vibrant' by Sain Store on amazon.com for $1.95 plus shipping. I'll let you know how THAT goes.
Also, Just a heads up. I have insurance on the phone. So I called up to find out what I could find out. First off, they don't care if you void the warrenty with software. Just so long as there is no physical damage and no water damage. Second, they HAVE to replace the Captivate with another Captivate if they have some left on the shelf. If they are out, they could have replaced it with a new Samsung Galaxy S II for the same deductible of $125. I'm holding off on replacing like for like right now until I try the JIG.
I may wait a month and see if they run out of Captivates too! lol.
I can do UnBrickable Mod for you if you'd like. I ask for $30 plus shipping (usually $6 unless you want overnight or something). Just send me a PM. I gaurantee that it will work unless you have hardware damage.
AdamOutler said:
I can do UnBrickable Mod for you if you'd like. I ask for $30 plus shipping (usually $6 unless you want overnight or something). Just send me a PM. I gaurantee that it will work unless you have hardware damage.
Click to expand...
Click to collapse
Trust me, that is the shiz....
Sent from my cell phone. DUH
@OP
AdamOutler said:
plug that into the stock charger outlet and have the kernel boot into battery charging mode, then turn it on normally from the charging mode.
Click to expand...
Click to collapse
(slightly edited)
I did not see if you say if you tried this, cuz I was gonna suggest the same.
leaked from my FUSED SGS I897 contaminating you via XDA app.
THE JIG WORKED!!!!! thanks guys!!!
OK so Thanks to the JIG, I was able to use the AIO root thingy and flashed back to stock, then rooted, then i was able to reboot to recovery, update.zip to clockwork mod, then installed cyanogenmod 7.1 zip from sd card.
then.. my 5 month old puppy promptly ate the JIG. lol...
Thanks everyone. Let people know that if they get the un animated wait animation screen like me, that the JIG will work
Hey folks, looking for a bit of help. So my wife washed my phone.(it didn't actually make it through the entire cycle because i realized what she did a minute or two too late. Regardless, the phone still got wet. I immediately pulled the battery along with SIM and SD.(I didn't try to power it on) I put the phone into a bag of rice and left it there for over 3 days. The phone seemed to be completely dried but i put it in the food dehydrator for good measure. The phone stayed in the dehydrator for 18+ hours. I reinserted the battery and plugged into AC and to my surprise I actually had a display. However, the phone gets to the AT&T screen and then reboots very near the end of the animation.(If left alone, the phone will boot loop indefinitely) I am able to boot into CWM recovery successfully. I tried flashing a ROM but the phone still boot loops. Flashing seems to work like it should, ie no errors, boot animation for ICS when flashing that. And yes, I've cleared cache/factory wipe/etc multiple times) I am unable to get into download via vol keys and usb cable to PC. I have a working jig that doesn't seem to invoke download mode either.(Plugging in the jig actually boots the phone into CWM recovery) The next step is to try forcing the phone into download via ADB.(downloading SDK onto new laptop now)
So after the above novel, my question is this: besides key combo, jig, and ADB is there an alternate way to force phone into download mode? A google search doesn't yield much...mostly articles ripped off of this site.
Is it possible to flash a .zip or script to force into download mode?
p.s. Odin does recognize the phone as a target when using the jig even though the phone is in recovery instead of DL mode.
Its worth mentioning that my lovely wife did spring for a brand new skyrocket the day my phone was washed meaning this phone is yet another to tinker with.
Wow what a great wife
Sent from my SAMSUNG-SGH-I727 using xda premium
You may have stuck volume buttons due to water or partial shorts on usb connectors. Try and get some isopro achohol and clean contacts and get compressed air spray to clear any debri
. Also take out sim card and clean it and the contacts
Good luck
Sent from my SAMSUNG-SGH-I727 using Tapatalk
brookfield said:
You may have stuck volume buttons due to water or partial shorts on usb connectors. Try and get some isopro achohol and clean contacts and get compressed air spray to clear any debri
. Also take out sim card and clean it and the contacts
Good luck
Sent from my SAMSUNG-SGH-I727 using Tapatalk
Click to expand...
Click to collapse
Thanks for the suggestion. I too considered that one of the buttons was stuck. However i am able to navigate within CWM recovery using the vol+ and the vol- buttons.
I actually did your other suggestion too.(not exactly but pretty close) I left that part out of my original post for the sake of brevity. Here's what I did:
I detached the the PCB from digitizer. I've got an electronics background so I happen to have quite a variety of small tools. One of which is a tiny medium/lite stiffness wire bristled brush.(It's like a tiny paint brush) I lightly brushed and cleaned all connections. This includes the connectable/disconnectable ribbon cables as well as any solder joint that I was able to access. Some ICs are "sealed" with epoxy so those connections couldn't be accessed.(Also seems like they stayed water proof) Basically I cleaned every place on the PCB that I saw irregularities. There were tiny spots of corrosive build up that looked as if they may be possibly shorting IC pins. Almost like "tin whiskers" except i used a magnifying lens and not a microscope.
I next used an air hose to remove debris I had just brushed off.(By the way, I like to stay away from canned air when using directly on components, it seems to leave a film. sometimes the un-evaporated contents also cause dust to cake)
I used a cap of isopropyl and some cotton swabs to clean the contacts further then let air dry. I wish I would have taken before and after pics because there was a huge difference. Anyways, this was actually done in between the bag of rice and dehydrator steps I mentioned earlier.
nthknd said:
Wow what a great wife
Sent from my SAMSUNG-SGH-I727 using xda premium
Click to expand...
Click to collapse
Yes sir. The original phone was bought out of contract at full price since I didn't want to wait for my upgrade to roll around. I was eligible for the contract discount this time.
Questions go in q&a
Here's the update:
I was able to force DL mode through ADB. Now that I can use Odin, I've realized that I'm not sure what i should flash. I'm thinking I'm going to try to completely return to stock. Simply flashing a ROM seems to work except for the boot loop. The boot loop happens regardless of the ROM i flash. The boot animation changes with different roms as expected. This leads me to believe the internal storage is indeed functional.
Should I try a kernel?
Bootloader?(is one even available?)
Stock Recovery?
silver03wrx said:
Questions go in q&a
Click to expand...
Click to collapse
Can I move this thread?
I hope it does move, this is an interesting story lol
Sent from my SGH-I727R using XDA App
My motherboard has quit working probably from rooting and overclocking. If anybody has any or know somebody that does I would highly appreciate it.
Wrong section
Search
sent from outer space.
Can you describe in detail why you believe its the motherboard...rooting should have no affect on the mother board and the oc levels in the kernels are set at safe/stable levels...but being a fairly old phone it could've jut crapped out lol
Sent from my HTC Holiday using Tapatalk 2
probably a stuck power button
The first thing that happen, I tried to flash the Samsung ics rom with touchwiz ui, then it would come back one. I finally fixed it once and it had froyo so I tried to flash gingerbread from Odin and that's the last place it messed up. I've tried everything from gtgs ultimate unbrick to heimdall one click. I'm stuck with an IPhone and I hate it I would love to get my phone working again.
I think its the motherboard because I have no other damage besides regular where and tear, no scratches in the screen just the back side. I have no water damage so I figured its the motherboard because nothing else makes sense
Well what exactly is wrong with the phone? Does it not turn on? Does it boot loop? Does what response happens when you attempt to turn it on?
It may sound sketchy...but if you can't get it going you can ship it to me and I can try...you'll just have to pay for shipping both ways...pm me if your interested in that -otherwise...well try our best to help you through the forums
Sent from my Vivid 4G using Tapatalk 2
It gets into download mode and that's about it, I can sometimes get it into recovery but I can't do really anything. I only flash the kernel and I get into recovery and can't get anything out of it. I am very desperate and I'm thinking about sending it to you
tmac42 said:
It gets into download mode and that's about it, I can sometimes get it into recovery but I can't do really anything. I only flash the kernel and I get into recovery and can't get anything out of it. I am very desperate and I'm thinking about sending it to you
Click to expand...
Click to collapse
If you can get into download mode then you should be able to get it running. Nothing to do with the motherboard..
Try the uclb3 heimdall one-click unbrick from qkster or some odin pack. If you are getting stuck during the process, switch usb cables & ports and keep trying.
If you give up and are willing to send it to mg, then go ahead; he should be able to do the job
I have tried every heimdall and odin. i will try to switch usb cords and ports and possibly computers, but i will probaly have to send it away if this dosnt work
Hey guys i know its a very critical conditions but there are so many guide in XDA so just search for it and relax
well i received the device today...and its even got me stumped...it almost seems like a power button issue but i know its not because it stays powered on through download mode...you can successfully flash a one click heimdal but then it just boot loops the charging animation...
as of now i think it may be a bad battery or the little connecter..but even then, why would it stay on while in download mode??
gonna give odin a try and see what happens...if odin doesnt work then ill see about getting a replacement battery and see if that helps...and if that doesnt ill have to ask permission to open it up and look inside and see if i see anything unusual
alright...ive discovered this under the battery...appears that something was removed and an inner part was scratched...can anyone verify that that whole isnt supposed to be there? (my infuse got stolen from my car a couple weeks ago)
that part under there i suspect may be part of the motherboard..and if it is scratched could be the likely cause of the booting issues - but still, why does download mode have no booting issues??
again this "hole" is on the bottom left corner of where the battery should be placed
I lied...after actually looking at the end results of heimdal...the flash isn't finishing...its cutting off towards the end and then rebooting...so maybe it is the power button...still...I don't think it is as the charging boot cycle is a good 5x faster then when the phone reboots in heimdal...I'm leaning more on bad battery
edit: 99% sure its a bad battery...as soon as I unplug it while in download mode the phone turns off...I used to be able to leave my phone unplugged in download mode for hours...
Sent from my HTC PH39100 using Tapatalk 2
Mine has the hole, but it's black and not scratched.
sent from outer space.
Tmac...please check your pms...I got the phone working - just need the shipping money so I can send it back...I have it all packed up...but I don't wanna keep a box laying around in my room
Sent from my HTC PH39100 using Tapatalk 2
mg2195 said:
Tmac...please check your pms...I got the phone working - just need the shipping money so I can send it back...I have it all packed up...but I don't wanna keep a box laying around in my room
Sent from my HTC PH39100 using Tapatalk 2
Click to expand...
Click to collapse
So was it the battery? Nosey people wanna know! :cyclops: :silly:
SteveCampsOut said:
So was it the battery? Nosey people wanna know! :cyclops: :silly:
Click to expand...
Click to collapse
Kindve...he must've bricked while the battery died so the phone no longer knew how to charge a dead battery...
Once I got the battery charged a little the and ran heimdall I was able to charge the battery again with no loops
This is a common problem with the HTC vivid (my other phone). The vivid is known for not being able to charge a completely dead battery requiring you to get an external charger
Anyways...tmac I'm still waiting for your response...been about two weeks since I last heard from you...does this mean I get to keep your phone LOL message me asap
Sent from my HTC PH39100 using Tapatalk 2
mg,
Ship it to me.
I'll ship it to qkster.
He can ship it to bigjoe who will ship it to Zen.
From there it can go to truckerglenn, then who knows. lol
Hello,
So last week I woke up and my power button stopped working. I looked around for similar issues and found quite a few stores selling a power flex cable (I attached a picture of it because I am a new member and cannot post the URL for the site, but it's easily found using google)
Since it was only six dollars, I ordered it without much thought. Just looking at the cable, it looks like it would fit into a connector rather than needing soldered onto a board, so I figured it would be pretty simple.I finally received it, and after looking around at a bunch of teardowns and the service manual, I do not see this cable or connection anywhere I was going to just open it up and check it out, but didn't want to risk not being able to turn the phone back on.
I am looking for advice! Specifically, if there is a way to power the phone back up without having to use the actual power button, I'd love to know.
FWIW, my phone is not rooted and factory stock
Thank you!
Bumping because I would really like to get this fixed! Not sure if this may go over better (or would be appropriate) on the i9300 forum.
Any help would be awesome!
Back up your phone in the way you see fit. Try and fix button. If you fix it yer done. If not buy a jig. The jig will get you into odin mode. Plug phone into computer. In odin make sure that auto reboot is checked. Flash something like a recovery. Once it finishes flashing it will auto reboot. Enjoy.
Use the home button to wake and a gesture gesture app to put a custom action to turn the screen off. Or put a screen off action on your home screen. Wherever you want
Sent from my SCH-I535 using xda app-developers app
That part has to be mislabeled. I just took my phone apart and there is no way that part will fit. Observe:
mentose457 said:
That part has to be mislabeled. I just took my phone apart and there is no way that part will fit. Observe:
Click to expand...
Click to collapse
Ugh, that is what I thought and was afraid of. I have no idea why in the world they are even available, lol.
I'll buy a jig just in case the phone somehow turns off and I am SOL.
Anyways, I appreciate everyone's input! TY