Hi folks.
My Tornado (imate sp5) was flashed from factory WM5 to WM6 with VJ Grace 3.3, it worked just fine. One day I lost conenctivity via activesync over the usb cable. BT activesync still works fine. I had not done anything to the connecter port other than using USB cable to activesync occasionally, and to use the wall charger.
After 2 months of going like this, I decided to upgrade to a newer Nitrogen ROM, and I enter the bootloader mode by pressig the camera button and plugging in the usb cable. The three color screen comes just fine.
Now, when I attach the USB cable, I do not see the small writing "USB" at the lower left hand corner.
Also I cannot connect it with Terraterm pro or the RUU utility, says phone is not connected via the USB.
But my usb cable still charges the phone when connected to the PC, even though activesync doesnt do anything.
Is there anything I can do?
Can it be a hardware error? Or a registry change I might have done using smarttweaks (enable/disable charging over usb-- I dont remember). If so can it be restored or undone?
I tried hard resets (clear storage and leftsoftkey/rightsoftkey/powerbutton combinations), but still it doesnt recognise activesync.
My other windows mobile devices get connected to same pc activesync with no problem, using the same data cable. Heck I even repaired by reflashing a friend's Wizard using the same pc and cable last week.
Is it possible that my tornado's usb connector port might have gone poof (it still charges the phone), and is there any remedy to that?
Thanks for reading, and please help..
Regards,
Steve
I've got the same problem. I can't connect via AS:/
I had a similar problem once in a while when I upgraded my phone to WM6; it seemed almost random. One day, the phone wouldn't switch out of Vibrate mode, and ActiveSync wouldn't synch with the phone. The first time it happened, I had VJGrace's 3.3, and 3.4 had just come out, so I went ahead and flashed it. I didn't format binfs or anything (which, in my experience isn't necessary for a functioning OS flash, just a clean one) but it flashed a fresh WM6 on, and the problem went away.
Then, a couple weeks later, I had the same problem again. It was right around the time that VJ's 3.7 came out, so I flashed that (again without format binfs) and it fixed the problem again.
Then, a couple weeks later, I had the same problem yet again. This time, Nitro's Platinum Edition had just come out, so I flashed it. Haven't had the problem again.
Interesting note - since I got my Tornado, my first Smartphone, I have only ever done the format binfs once - the first time I flashed WM6. Haven't done it since. It's my opinion that format binfs gives you a CLEAN install of WinMobile, but is not strictly necessary.
So, to summarize: try direct-flashing a new WM6 install. Just plug in the USB cable - ignore ActiveSync when it fails to synchronize - and run the updater program. It'll take care of the rest, even if AS doesn't synch.
djsleepwalker:
If you lost USB connectivity, how did you flash your phone?
Should I read between the lines that the bootloader connected properly and that it was a WM6 driver problem?
Exitao said:
djsleepwalker:
If you lost USB connectivity, how did you flash your phone?
Should I read between the lines that the bootloader connected properly and that it was a WM6 driver problem?
Click to expand...
Click to collapse
To be totally honest, I'm not 100% certain. See, ActiveSync wouldn't SYNCH with the phone, but I could still "Explore" the phone. WM6 was active and working, and charged via USB cable, it just wouldn't synch.
So, after I connected the USB cable and ActiveSync popped up a message that said it couldn't synchronize with the phone, I just started up the ROMUpdateUtility program. It rebooted the phone into the bootloader for me.
I honestly never tried to start it back up in bootloader mode. The only reason I decided to just flash a new ROM was because I had already downloaded the ROM, but where I was at the time, I had no internet access (and therefore couldn't remember the steps before flashing the new ROM.) A friend of mine who has a Wizard (and who, I think, might be a member of this forum) suggested that I didn't *have* to format binfs to put an updated ROM on the phone, so I said screw it. I needed it out of Vibrate mode (my phone is my second alarm - my second line of defense against oversleeping) so I flashed the new ROM.
ninja edit: If ccpraveen is getting *nothing* when he connects the USB, then my suggestion probably won't help. But if Windows recognizes something being connected, and he can *explore* the phone, but ActiveSync just won't synchronize, then he's probably having the same problem I was. I can't tell for sure from reading his post.
Sweet...
Thanks for the comments, its all dejavu again
Djsleepwalker's comments did make me wonder, hey this is exactly my problem, except that mine doesnt connect in any manner.
Lots of similarities, problems started with VJ 3.3, on and off for a while with USB, then totally lost connection.
I am not concerned with formatting BINFS now, I somehow want to get the phone recognized.
Exitao has actually asked a VERY VALID query. It is indeed impossible to flash a phone without any USB connectivity (unless via an SD image or something). Djsleepwalker's issue was minimal, only that the PC was not showing up the activesync as connected, but indeed there WAS a connection, he could explore the phone from the pc etc, and I bet if he did go into the 3 color screen, he would have seen the "USB" on the left lower portion.
So, mine is just that. No connectivity. Nada. PC just sits dumb. Phone just gets charged, and finally into the fully charged green LED. Thats it.
Could there be something in VJ's ROM that is doing this?
I wonder, because a Wizard I once tried to repair would not let me flash upgrade either. I had to go back to a basic BUTTON ROM to get the upgrades running properly again. But there atleast I had connectivity then.
After I read DJ's comments, I tried running the RUU straight, without getting into the bootloader (for a change). Again its the same error 260. Here is a screenshot.
Anybody?
Regards
Steve
It seems, from the description, that the activesync profile became corrupt.
Deleting any device profiles from Activesync and connecting the phone as a new device might also solve the problem. However, it might be active synch on the phone that is the problem...
Anyone unsure how serious their problem is should just turn off the USB connect in activesync, start the phone into boot loader and do an "info 2" with terraterm pro.
If terraterm discovers the device, the USB is not the problem. It's activesynch.
Terraterm pro would not connect either.
I started the phone into bootloader by plugging in the usb while keeping the camera button pressed. Started the terraterm pro, selected Serial > USB, clicked Ok, Terraterm says ERROR, Cannot Open.
One minor thing, what do ppl normally see in their bootscreens? I see these lines, Tornado IPL 2.00 Tornado SPL 2.00.0000 and another line Tornado IU.
I dont remember seeing this third line saying Tornado IU before. Is it normal? It is in the middle zone( green coloured zone).
I believe my usb connector port might have a physical error. What else it could be. PC just will not detect ANY sort of USB connection.
Thanks again Exitao, I am stumped.
Regards
Steve
Have you tried any other USB ports on your computer? I know it's a longshot, but on my desktop PC one of the onboard USB ports just doesn't function at all. The other three do.
ninja edit: Maybe try it on another computer, too?
I tried on all four USB ports of my laptop, as well as on another Desktop PC I have.
Even without activesync installed, plugging in this should bring out a DING, saying something has been connected to the PC USB. (and asking for drivers, if Activesync was not installed. Here nothing happens, no DING). Remember, the same USB port is being used to sync my Wizard, Blackjack 2 and my old Himalaya even now.
Another possible reason, I was using a dumb chinese charger for charging the phone, after I lost the original one. Could that might have fried the usb pins?
ccpraveen said:
I tried on all four USB ports of my laptop, as well as on another Desktop PC I have.
Even without activesync installed, plugging in this should bring out a DING, saying something has been connected to the PC USB. (and asking for drivers, if Activesync was not installed. Here nothing happens, no DING). Remember, the same USB port is being used to sync my Wizard, Blackjack 2 and my old Himalaya even now.
Another possible reason, I was using a dumb chinese charger for charging the phone, after I lost the original one. Could that might have fried the usb pins?
Click to expand...
Click to collapse
Please excuse me if I'm stating the obvious, or if I'm a bit off, as I don't haven't used my Tornado in a bit (upgraded to Touch Cruise), but in the last ROM I used, NitroGen's latest WM6 version, there was an option in settings to disable usb connectivity and only allow USB charging. Perhaps VJ's ROM has the same option and you activated it. Have you already checked this?
Did you remeber to uncheck "Alllow USB connections" in activesync before you connected the boot-loaded phone?
This may be a hardware problem. Is it possible to use a can of compressed air to blow out any dust or debris from the USB socket on the phone?
Do you have WMStorage on your phone? If not, can you load it onto your storage card and install/run the app and see if the PC will recognise your device as a USB mass storage device?
I guess you also want to check the Device Manager in Windows and check for any exclamaition marks (!) or "bangs." Both with the phone disconnected and connected, and maybe even with wmstorage enabled. If it does show your phone in the device manager, delete or remove the device in the manager and reboot.
(To get to device manager, you can right click on "my computer" and select "properties", or press the Windows key and the Pause/Break key, or go to the control panel applet.)
BTW: is this XP?
If you are using Vista, try the following:
Step 1: Press Start
Step 2: Select settings
Step 3: Select (6) Connections
Step 4: Select (0) More
Step 5: Select (1) USB to PC
Changing the type of USB connection your device uses can help with problems
connecting ActiveSync.
Step 6: Disable the option - Enable advanced network functionality
Step 7: Press done 3 times
Step 8: Return to main screen.
Step 9: Uninstall unrecognized USB device in device manager (on PC)
Step 10: reboot Phone and reconnect
Click to expand...
Click to collapse
If XP, keep going...
You've stated that the PC is recognising your other devices. Isn't there a limit to the number of windows mobile devices you can sync or associate with one installation of activesync? Can you delete a device and try again?
Is USB charging enabled or disabled in your phone? Try toggling the setting to opposite whatever it is.
If you are using a firewall app, add these programs to your firewall's exemptions:
# Wcesmgr.exe
# Wcescomm.exe
# Rapimgr.exe
Or simply disable any firewalls, network traffic optimisers or possibly antivirus (some have network protections) app to test if that has an effect.
Ok guys..
I will try doing all these, step by step and lets see
And accept my sincere gratitude from my heart for detailing all these info for me, I am soo deeply moved
Sincerely
Steve
ccpraveen said:
Ok guys..
I will try doing all these, step by step and lets see
And accept my sincere gratitude from my heart for detailing all these info for me, I am soo deeply moved
Sincerely
Steve
Click to expand...
Click to collapse
No need for thanx. If I helped, just give Nitro a donation on my behalf.
Well guys, with deep regret, I must say, even after trying all that, the phone stays put. PC wont recognise it, neither as a phone nor as a mass storage device. The connector port must have gone kaput.
I kinda feel stupid, u know, with all the tweaks and hacks out there, what use it is, if the dumb thing wont be recognised? Hmm.. So much for the tornado, now stuck at VJ 3.3 (unless someone find a way to flash via an SD image or something).
Well, thanks guys, your support did make me feel better, in the WM world, all is not lost, as long as there are good souls like you, willing to help, live and let live.
Regards
Steve.
PS: If the phone was not recognised in the bootloader mode, (ie even before the operating system has kicked in), I guess there should not be any difference if activesync was installed or not; and if or not mass storage option is enabled or not, right? Well, correct me if I am wrong, I think so. Could be wrong.
This is probably a useless comment, but have you tried using bluetooth instead of usb to connect to your computer?
Have u tried to delete the network card from XP device manager ?
U can also disable advanced network functionnality from your smartphone in "settings" -> "connections" -> "USB to PC"
Good luck
Can You Tried Different Usb Cable :d
i have some problem, after flashing to WM6 activesync or WM5torage can't connect..i have HTC prophet too, and i use same usb cable & PC, my HTC Prophet still can connect via activesync or WM5torage
*please..please..help us
I UPGRADEd vjgace Build_5.2.1616.18120_____v3.7 three days before today i can't connect to usb i tried diffrent app(activesync,wm5storage,internetsharing) but i can't connect so i go to bootloder mode and checked devicemanager i found device so i flashed nitrogenius rom and now working usb. try upgrade other ROM ON BOOTLODER MODE.
I've had my g1 for about 2 weeks. I have root. I have the RC33 update. I was able to connect to a pc after this update then one day I tried to get this song off of the computer so I plugged in the phone and it said "found new hardware"....I have tried everything different pc's different usb ports,different storage cards,....I tried the anycut app method....failed on one pc it opened on my laptop and then shut off again....I've soft reset,hard reset...removd the card and put it back in...no luck...any one with the answer please help...I will love you long time!
And the pc does recognize the phone is plugged up because its charging...
Hi,
Found new hardware means it was trying to install the usb drivers for your g1.
If this was not done correctly, than several things won't work like adb.
So that's what that message is.
But unplug your phone and go into settings, applications, development uncheck the box that says usb debugging,
Exit out and connect your cable, mount you drive and you can transfer files back and forth again.
Ok I did that but the box was already unchecked...so I plugged up the phone...and nothing happens so I check the box and the g1 acknowleded the pc and vise versa....and the installation wizard is for Android Phone...and is asking for an installation disk...so now I'm back to square 1...
Once you have plugged in the USB cable and Windows has recognized your phone (i.e. no new hardware found dialog anymore), you need to pull down the notification bar of the G1 and click on "connected to USB" or something along those lines. The phone will then give you an option to mount the SD card for read/write over the USB cable.
hi,
I am an advance user and recently brought the Samsung Omnia W i8350 a.k.a Samsung Focus Flash. Initially it connected fine and updated twice with zune since the initial stock version.
I did not had time to explore much and I am pretty new to the Windows Phone 7 environment. few days back when I connected the phone to the PC, the device was recognized as GT-I8350 and windows kept on searching for drivers but no drivers were located. I tried installing the zune drivers but even they do not allow me to connect the device to zune (hence no music, no updates, no backups )
Then I downloaded drivers from tsar3000 and they automatically instal 3 devices off my phone, one was a com port, one was modem , and so on...
STILL NO CONNECTION TO ZUNE.
I have tried almost everything but to no avail. can you guys help me?...
Regards
PS: between the last successful connect and unsuccessful connect, there was a time when Win7 stopped booting, so I simply stopped many services and booted again because I had a presentation and no time for a fresh install, could this possibly be a service issue?... I tried starting some services but the did not work. Can anyone enumerate the services required by winP7.5?... also if a manual driver is available, it will be appreciated.
PPS: I also tried running the windows phone 7 drivers from zune folder, it gives an error the device cannot start.
You put the phone in tethering mode, it sounds like. The COM port and modem drivers indicate that the phone is sending a different USB device ID than normal. On the gen1 Samsung phones (and quite possibly on the gen2 ones, but I havne't checked) you could put the phone's USB port in a mode where it would act as a modem for the PC. It sounds like that's what you've done.
Try a search on "WP7 Samsung tethering" or similar and see if you can put the phone back in its normal mode.
GoodDayToDie said:
You put the phone in tethering mode, it sounds like. The COM port and modem drivers indicate that the phone is sending a different USB device ID than normal. On the gen1 Samsung phones (and quite possibly on the gen2 ones, but I havne't checked) you could put the phone's USB port in a mode where it would act as a modem for the PC. It sounds like that's what you've done.
Try a search on "WP7 Samsung tethering" or similar and see if you can put the phone back in its normal mode.
Click to expand...
Click to collapse
hey thanks,
I was just reminded, that I was one day testing the steps mentioned on this thread, to use the phone as USB modem, hence had left it there since then, Never used it though.
Great! Solved!
Hey guys,
I'm trying to root my blaze so i can go from gingerbread to CM10, however i noticed my phone's mass storage function isnt even turning on... and obviously i cant run ODIN without my computer recognizing the phone. I tried turning debugging mode both on and off, etc.
When i plug the usb cable from phone to computer, it only charges. There's no setting in the pull-down menu saying anything about mass storage, no usb icon on top, that whole (software) part of the phone seems to be missing. I just bought this thing unlocked.. its not rooted and i did a hard reset as well.
When i go into settings/ wireless/ usb utilities, i see the mass storage button. It says Connect storage to PC. if my usb cable is plugged in, it says "USB is connected. Remove the cable." If its not connected and i hit the button, it says "please connect cable" and once i plug it in, nothing happens but charging. Any ideas? Can i root using kies?
Thanks for the help!
hwmpunk said:
Hey guys,
I'm trying to root my blaze so i can go from gingerbread to CM10, however i noticed my phone's mass storage function isnt even turning on... and obviously i cant run ODIN without my computer recognizing the phone. I tried turning debugging mode both on and off, etc.
When i plug the usb cable from phone to computer, it only charges. There's no setting in the pull-down menu saying anything about mass storage, no usb icon on top, that whole (software) part of the phone seems to be missing. I just bought this thing unlocked.. its not rooted and i did a hard reset as well.
When i go into settings/ wireless/ usb utilities, i see the mass storage button. It says Connect storage to PC. if my usb cable is plugged in, it says "USB is connected. Remove the cable." If its not connected and i hit the button, it says "please connect cable" and once i plug it in, nothing happens but charging. Any ideas? Can i root using kies?
Thanks for the help!
Click to expand...
Click to collapse
You can't root via kies. But you can upgrade to ICS via kies and see if that helps. Provided kies recognizes your phone... Otherwise, I know very little about GB since I immediately upgraded to ICS upon purchasing my Blaze.
Have you seen mobileodin?
Sent from my SGH-T769 using Tapatalk 4
@ njstein, I see the update now that you mentioned it, although it looks like the update is no longer provided? Check out these links, the samsung site link is broken for tmobile blaze, and the tmobile site link shows in the info box on top that the upgrades were only being provided until March 5? *I put a space between the .com on the links because i'm not allowed to post links yet*
samsung. com/us/support/SupportOwnersFAQPopup.do?faq_id=FAQ00046726&fm_seq=49755
support.t-mobile. com/docs/DOC-4182/
@ Somcom3X, I'll see if i can find threads on this forum about mobileodin. I think if i can just root the damn thing to bring it up to CM10 the rom should include usb cable software, correct?
I'll see if I can make something happen. Thanks for the tips guys.
@njstein On that tmobile link i put up, it says that software version T769UVLF5 wont receive the update because it is up to date??? That makes no sense as i'm on that version running GB. Are they trying to say that for whatever reason my phone cant do the upgrade? One thing after the next..
Somcom3X said:
Have you seen mobileodin?
Sent from my SGH-T769 using Tapatalk 4
Click to expand...
Click to collapse
It appears only the model 9000s galaxy S is compatible with mobile odin, i dont see anything about the blaze. I couldnt post a message on the mobile odin thread due to low post count. I also read that your phone must be rooted to be able to use mobile odin. Do you guys have any other ideas how i can root my phone without a usb cable?
I have a note 2 I currently use- when I plug the usb in - in windows 7 I get the option to view files etc....
I just bought a used sprint galaxy s5 from my ol ladys sister who had it hooked up at one of those corner wireless shops.
I want to root it but read to make sure your pc recognizes it first- which it does not.
Ive downloaded the latest usb drivers for the phone.
Ive enabled debugging mode.
Ive used the original supplied cord and also tried my note 2 cord.
When I plug it in it recognizes it and detects drivers but the phone does not show up under my computer and I dont get the window popup asking if I want to view files etc.
Getting really frustrated.
Any ideas?
deezdrama said:
I have a note 2 I currently use- when I plug the usb in - in windows 7 I get the option to view files etc....
I just bought a used sprint galaxy s5 from my ol ladys sister who had it hooked up at one of those corner wireless shops.
I want to root it but read to make sure your pc recognizes it first- which it does not.
Ive downloaded the latest usb drivers for the phone.
Ive enabled debugging mode.
Ive used the original supplied cord and also tried my note 2 cord.
When I plug it in it recognizes it and detects drivers but the phone does not show up under my computer and I dont get the window popup asking if I want to view files etc.
Getting really frustrated.
Any ideas?
Click to expand...
Click to collapse
When I plug the s5 into my pc and pull down the notification bar ...it doesnt even show usb connected.
I cant find any usb options other than usb debugging.
I just went through all this same crap with a galaxy mega a buddy had.
I just dont get why there is no "usb connected as" notification and why this is so complicated to connect to pc when my note connects fine
Bad cable? Maybe Bad Drivers? Where did you download them from? Windows is going to try to recognize it as a media device. Ill give you a couple tips
Just because the "popup window" doesnt popup, you probably just have auto play set to recognize it a certain way.
Just copy and paste this into your explorer window:
%windir%\system32\control.exe /name Microsoft.AutoPlay
and then reset it for your phone.
Also.
1. Make sure the cable is actually connecting, like charging the phone, consistantly, not on and off. If it is, then you know thats good, if not, switch the usb drive you have the cable plugged into. USB Ports actually on the motherboard are the ones Ive always had luck with never disconnecting.
2. If you want to root your phone, and you want the adb drivers, Windows wont find those for you.
Thanks for the reply.
I downloaded the drivers straight from the windows usb driver dowload page for my phone from samsung.
Ive uninstalled reboot,installed rebooted.
Ive set usb debugging off/on.
Tried dialling *#0808# which ive read is the code to enable usb but it doest work it just calls the #.
Tried all my moyherboard usb ports
Tried different cable
The original cable charges fine.
This sg5 NEVER has a usb icon when connected to usb... i find that odd.
A samsung mega a buddy had which was also previously hooked up at the same wireless shop that this s5 was..... also has the same exact issue.... no usb icon and not recognised as media by windows and no way to change usb settings.
Its like that wireless shop disabled usb on there phones for some reason.
I had the phone 2 weeks and cant do anything with it untill I can root it.
My note 2 works fine , i get usb icon in notification area,i can switch to media device from there.
On the sg5 theres no usb icon even though it connects fine to the pc as installer
Sent from my SCH-I605 using Tapatalk
Maybe Im misunderstanding you, but when I have my phone plugged into my pc there is no usb icon, its just connected as a media device and shows its charging. Both screenshots are of my phone while its plugged into my computer
When you plug it into your computer can you access the files on the phone through your windows explorer, like in the first screenshot?
Thanks for replying and the screenshots.
When my phone is plugged into the computer it shows the charging status but no "connected as media device" it doesnt show a connected as anything so nothing to touch for options.
The phone does not show up under windows explorer in my computer.
Ive been using galaxy phones since the original galaxy and never had issues like this.
I just dont get it
I'm similar issues...my phone will just time out in the middle of transfers or won't see the phone at all
Both of your issues sound like driver issues. Heres the link from Samsung for Windows for the S5
http://www.samsung.com/us/support/owners/product/SM-G900PZKASPR
To make this issue stranger....
My neighbor came over to borrow juice for her ecig. I noticed she has an s5.
I ask if i can connect it to my computer and as soon as I plug it in with my s5 cable...bam ...connected as media device , touch for usb options.
And my computer brought up the screen to view files.
So i now know its not my pc,drivers, or cables.
I did however notice when I plugged my s5 in.... in the notification area where it would say touch for usb options.
It says "system update"
But i have no sim or service on the phone so it doesnt update.
Could the system update be needed for the usb to work?
How would i even update system ?its nolonger on sprint. I wouldnt want any more over the air updates anyway as im wanted to root so i can save a straight talk apn and probablly flash a custom rom
Yea... this is nuts.
This sprint s5 i got looks and performs like a brand new phone.
But cannot for the life of me get "connected as ......" to show when a usb is plugged in. When i search settings for "pc connection" , "media" , mtp" , usb" etc.....
Theres nothing I can find to enable how to connect when usb is connected.
I dont even know who or where to ask anymore.
Bought this phone weeks ago and cant do anything with it.
My neighbors s5 connects to my pc no problems. So does my note 2.
I just dont know anymore what else to do
i dont see where not having a sim would matter. does the usb port on your phone seem loose or anything? do you have access to another pc to try connecting to that?
ultimately you can get around most things that require needing a usb connection. theres even a wireless adb.
i doubt this will work either, but have you tried seeing if odin will recognize the phone in download mode? (power off the phone and press the power+home+volume down buttons)
also what version of android is on the phone now? if its still on 4.4.2 or 4.4.4 then you might want to look into towelroot, but i think i remember reading thats not working with 5.0
as for rooting, you could try looking for a flashable update.zip , put it on a external sd card, put that in your phone and boot into recovery (power off the phone and press the power+home+volume up buttons) and flash it, then find a custom recovery like clockworkmod or philz touch or something
all in all im 99% sure theres a way to root the phone without having to do anything on a pc, its just a matter of finding a way to do it, and the before choosing a method to tell you to try, i need to know the android version. also im just assuming the model number is SM-G900P, is that right?
Go into your settings and tell me the
Software Version
Model Number
Android Version
and the Baseband Version
once factory reset...usb works fine.
Im now rooted and flashed MOAR
thanks for all who tried to help
Glad you got it figured out