Related
Hi guys,
I own a POLA100 Cruise.
I:
- Downloaded polymod 2.1g UPDATE + DARK THEME 04 Mar
- Downloaded Haret Install
- Renamed default.txt to original-default.txt
- Renamed defalult-polaris.txt to default.txt
- Partitioned a 2 Gb SD as: 900 Primary Fat32 + 1024 Extended (2 x 512 Ext2 Partition).
- Copied on Fat32 partition the folder "andboot" Haretinstall+Pack.tgz
... I launch Haret....
THE FIRST TIME ... Linux booted, but when i hold the D-Pad... Cruise show @A ... and then TIMEOUT.
Now (from second time to now....) ... Haret Run... and I see wierd color and bad lines on the screen.
What I can do to launch a good android image on my Pola100 ?
Anyone can create a "Pack" with Haretinstall, the right default.txt and the polymod 2.1g UPDATE + DARK THEME 04 Mar of this thread http://forum.xda-developers.com/showthread.php?t=600154 ?
Thanks a lot.
I know that I'm not helping, but... I have the same problem here.
foxct2005 said:
Hi guys,
I own a POLA100 Cruise.
I:
- Downloaded polymod 2.1g UPDATE + DARK THEME 04 Mar
- Downloaded Haret Install
- Renamed default.txt to original-default.txt
- Renamed defalult-polaris.txt to default.txt
- Partitioned a 2 Gb SD as: 900 Primary Fat32 + 1024 Extended (2 x 512 Ext2 Partition).
- Copied on Fat32 partition the folder "andboot" Haretinstall+Pack.tgz
... I launch Haret....
THE FIRST TIME ... Linux booted, but when i hold the D-Pad... Cruise show @A ... and then TIMEOUT.
Now (from second time to now....) ... Haret Run... and I see wierd color and bad lines on the screen.
What I can do to launch a good android image on my Pola100 ?
Anyone can create a "Pack" with Haretinstall, the right default.txt and the polymod 2.1g UPDATE + DARK THEME 04 Mar of this thread http://forum.xda-developers.com/showthread.php?t=600154 ?
Thanks a lot.
Click to expand...
Click to collapse
edit the default.txt to:
set RAMSIZE 0x08000000
set MTYPE 1723
set KERNEL zImage
set initrd initrd.gz
set cmdline "board-htcvogue.panel_type=1 ppp.nostart=0 pm.sleep_mode=1 mddi.width=240 mddi.height=320 lcd.density=120 no_console_suspend board-htcpolaris-battery.battery_capacity=1350 mddi_client_vogue.vsync=0"
boot
if this also not boot change: board-htcvogue.panel_type=1 to 3
Hi,
use warmdonut from http://forum.xda-developers.com/showthread.php?t=619980
version 240x320. Copy it to your sd-card, run haret using default-polaris.txt. Immediately after you've pressed "run", press d-pad as long as needed to start setup (seems to be very long...).
It's important to press d-pad during boot of android. After installation it runs like a charme. When u need wlan, do an update using the provided wlan update.
No need to do any changes to default-polaris.txt exept if you don't want to start ppp at bootup. This release is much faster than polymods.
Have fun ;o)
foxct2005 said:
THE FIRST TIME ... Linux booted, but when i hold the D-Pad... Cruise show @A ... and then TIMEOUT.
Now (from second time to now....) ... Haret Run... and I see wierd color and bad lines on the screen.
Click to expand...
Click to collapse
I have the same problem sometimes.
There are 3 situations I met.
(1) Wierd color screen with no response.
(2) An error message shows after "Press the DPad".
(3) A Successful boot.
Either (1) and (2) will happen if the boot text doesn't show immediately after the vibration of Haret Run. If the boot text shows immediately (maybe within 5 seconds) after the vibration, there will be a successful boot. Though I don't know which time it will success, I always press the DPad just after the vibration. If it fails, I will do soft reset and try again (or give up).
I change only zImage to zImage-eclair in the default-polaris.txt when using polymod 2.1g. For Myn's Warm Donut, I change nothing.
So, you may do more tries.
p.s.
I use fat32/Ext2/Ext2.
Although the speed of polymod improved, still much slower than the Myn's. But the Myn's seems to have more little problems on Polaris.
Sorry for my English.
Good luck.
solvga said:
(1) Wierd color screen with no response.
(2) An error message shows after "Press the DPad".
(3) A Successful boot.
Click to expand...
Click to collapse
Exactly the same for me. Most of the times its the first scenario for me.
Even after a successfull installation i have problems after a softreset.
I launched Haret and hold D-Pad immediately after Vibrate on RUN... and during all boot sequence... but i have this error
msm_i2c.0: error waiting for notbusy
Some suggest?
Bye.
foxct2005 said:
msm_i2c.0: error waiting for notbusy
Click to expand...
Click to collapse
That is what I mean by (2) An error message shows after "Press the DPad".
Just try Haret again.
code PIN problem
Hi,
I have another problem with installing Android via SD.
Everything works but at the time of typing PIN code, I enter my PIN code but Android tells me it's an "incorrect pin".
Do you have the same problem?
thanks
I made other 5 tries... 2 with polymod and 3 with wormdonut...
In these tries... both with polymod and wormdonut i had this:
- Running Haret
- After Vibrate... Hold D-Pad
- Even D-Pad hold.... i had a messange "error waiting for not busy"
- I released D-Pad and Hold Again
- After some times of error "error waiting for not busy".... INSTALLED STARTS!!!!
- I had on Screen the message "Warning - Installing android can wipe your device <OK> "
- I pushed D Pad to Give "OK", but nothing happened on my cruise....
- Then.... "Error waiting for busing... in loop"... and I can't install anything.
My question Is.... after install Starts and warning message appairs.... what i can do to launch install ?
Which ways to select ? D-Pad ?
If i could press <OK>... which install method i have to select to install ?
Regards.
FoxCT.
damdirt21 said:
Hi,
I have another problem with installing Android via SD.
Everything works but at the time of typing PIN code, I enter my PIN code but Android tells me it's an "incorrect pin".
Do you have the same problem?
thanks
Click to expand...
Click to collapse
disable pin win wm
Which default.txt have you used? I tried it with adapted ones several times and always got this "..waiting for no busy..." error. Stepping back to original default-polaris.txt everything worked fine even after reset.
=)
thank you very much, It works now =)
to GOY2K - installation problems
goy2k said:
Hi,
use warmdonut from http://forum.xda-developers.com/showthread.php?t=619980
version 240x320. Copy it to your sd-card, run haret using default-polaris.txt. Immediately after you've pressed "run", press d-pad as long as needed to start setup (seems to be very long...).
It's important to press d-pad during boot of android. After installation it runs like a charme. When u need wlan, do an update using the provided wlan update.
No need to do any changes to default-polaris.txt exept if you don't want to start ppp at bootup. This release is much faster than polymods.
Have fun ;o)
Click to expand...
Click to collapse
dear GOY2k
i am having the problem at the first step. i downloaded the 240x320 file, then installed it in SD card (i have a micro SD card) in folder andboot. then i ran Haret and pressed the Dpad button and have kept it pressed. For the next 20 minutes i have just stayed in that position, with nothing happening at all.
kindly tell me where i am going wrong.
regards
o2-lover
to Goy2k - new problems
goy2k said:
Hi,
use warmdonut from http://forum.xda-developers.com/showthread.php?t=619980
version 240x320. Copy it to your sd-card, run haret using default-polaris.txt. Immediately after you've pressed "run", press d-pad as long as needed to start setup (seems to be very long...).
It's important to press d-pad during boot of android. After installation it runs like a charme. When u need wlan, do an update using the provided wlan update.
No need to do any changes to default-polaris.txt exept if you don't want to start ppp at bootup. This release is much faster than polymods.
Have fun ;o)
Click to expand...
Click to collapse
DEAR Goy2k
i finally got around to get installation process started - i changed default.txt to default-polaris.txt and it got started.
it asked me options and i chose INSTALL SYSTEM.
after installation started, i followed it as much as i could and i found that in many places, it kept mentioning cannot find or cannot install.
in the end, it fails to install android and the first menu comes back giving options. i finally quit after 3 tries.
what mistake am i making.
regards
o2-lover
to Goy2k - one step ahead - new problem
goy2k said:
Hi,
use warmdonut from http://forum.xda-developers.com/showthread.php?t=619980
version 240x320. Copy it to your sd-card, run haret using default-polaris.txt. Immediately after you've pressed "run", press d-pad as long as needed to start setup (seems to be very long...).
It's important to press d-pad during boot of android. After installation it runs like a charme. When u need wlan, do an update using the provided wlan update.
No need to do any changes to default-polaris.txt exept if you don't want to start ppp at bootup. This release is much faster than polymods.
Have fun ;o)
Click to expand...
Click to collapse
Dear Goy2k
i finally got to the following stage now, after various steps-failure messages during installation:
my set rebooted and ANDROID is written in a black screen. a cursor runs below it from left to right. sometimes it stop at the right, then after a while screen goes blank and then ANDROID reappears and the curson starts again.
currently this is going for about 10 minutes or 15 minutes already.
is this going in the right direction? anything else supposed to happen? or should i wait till the battery dies??
i hope you get this now and can reply now.
regards
o2-lover
to Goy2k - final step apparently
goy2k said:
Hi,
use warmdonut from http://forum.xda-developers.com/showthread.php?t=619980
version 240x320. Copy it to your sd-card, run haret using default-polaris.txt. Immediately after you've pressed "run", press d-pad as long as needed to start setup (seems to be very long...).
It's important to press d-pad during boot of android. After installation it runs like a charme. When u need wlan, do an update using the provided wlan update.
No need to do any changes to default-polaris.txt exept if you don't want to start ppp at bootup. This release is much faster than polymods.
Have fun ;o)
Click to expand...
Click to collapse
Dear Goy2k
i am sure you must be laughing by now at my follies.
i have been hoping for a long time to install ANDROID on my O2 XDA ORBIT II.
now, the ANDROID screen has progressed to a new bottleneck. A BLACK SCREEN showing the words 'COULD NOT SET PROPERTY'. this has come twice.
and now for the past 10 minutes or so, i am stuck at this screen.
how long is this supposed to take ??
regards
o2-lover
Hi O2-lover,
sorry for that late answer, but I'ven't got the time to look for this thread. I'm using a Orbit 2 too. All I've done was to use default-polaris.txt. I only got in trouble when I tried to install it on SD-Card (I think this is one option). Later I created 2 ext2 (each 256mb) patitions and one swap partition. On installation I choose to install it on ext2 (both, system and data).
From now, I think my data partition is not used, but I'll sneak around at weekend, maybe to install it on NAND.
to Goy2k - i got it working finally
goy2k said:
Hi O2-lover,
sorry for that late answer, but I'ven't got the time to look for this thread. I'm using a Orbit 2 too. All I've done was to use default-polaris.txt. I only got in trouble when I tried to install it on SD-Card (I think this is one option). Later I created 2 ext2 (each 256mb) patitions and one swap partition. On installation I choose to install it on ext2 (both, system and data).
From now, I think my data partition is not used, but I'll sneak around at weekend, maybe to install it on NAND.
Click to expand...
Click to collapse
dear Goy2k
thank you for the reply. after a number of tries, i finally got android installed. but it does have a big disadvantage. sometime or the other you are bound to have to switch your phone off for some reason. or you may forget to recharge the battery on time. well, when you switch it on, it goes back to windows.
SO UNLESS YOU ARE ABLE TO FLASH ANDROID ROM, it is not going to be a long time fun.
i am now going to try and get win 6.5. i have already upgraded to 6.1 from 6.0
best regards
o2-lover
For some reason I can't get my Polaris to run the latest Android version (i.e. Froyo).
1. Downloaded latest kernel (polaimg-panel3-320-froyo-07-07-10.nbh)
2. Downloaded last build (Incubus26Jc's Super FroYo RLS10)
3. Put last build (.tar or .tgz file) on SD card in directory /andboot
4. Flashed by using NBH file together with RUU Update Utility
Now it gets tricky:
a) or the system reboots, vibrates twice, I see a red and blue line and then a black screen and nothing;
b) or the system reboots, I get the Android installation menu after pressing middle button, install, but after soft reset I get a "No such file found" kind of system error
Can someone help me getting Android on my old Polaris? Thanks!
SnoopThaDoctor said:
For some reason I can't get my Polaris to run the latest Android version (i.e. Froyo).
1. Downloaded latest kernel (polaimg-panel3-320-froyo-07-07-10.nbh)
2. Downloaded last build (Incubus26Jc's Super FroYo RLS10)
3. Put last build (.tar or .tgz file) on SD card in directory /andboot
4. Flashed by using NBH file together with RUU Update Utility
Now it gets tricky:
a) or the system reboots, vibrates twice, I see a red and blue line and then a black screen and nothing;
b) or the system reboots, I get the Android installation menu after pressing middle button, install, but after soft reset I get a "No such file found" kind of system error
Can someone help me getting Android on my old Polaris? Thanks!
Click to expand...
Click to collapse
Same for me with polaimg-panel3-320, but it works great with polaimg-panel1-320-24-05-10.nbh
Thanks! Got it working with the older NBH file. Not completely flawless, but it works!
Don't use the old polaris panel 1 nbh, instead download the latest and then use this utility to change it to panel 1.
http://forum.xda-developers.com/showthread.php?t=689812
Thanks!!! Got it working with the latest NBH files! Great!!!
Hey, Could anybody unswer me on two questions.
1. why we have to change from panel3 to panel1 in this nbh file?
2. what is that mean panel3 or 1? why DZO do this type of the nbh (with panel3 i mean)?
thanks a lot, ithin it will helps not only me but everyone in future who didn't know about this modification
skydemon said:
Hey, Could anybody unswer me on two questions.
1. why we have to change from panel3 to panel1 in this nbh file?
2. what is that mean panel3 or 1? why DZO do this type of the nbh (with panel3 i mean)?
thanks a lot, ithin it will helps not only me but everyone in future who didn't know about this modification
Click to expand...
Click to collapse
The panel type depends on revision of your polaris, more specifically the make of the lcd panel, see here. I just tried every panel until I found one that works, I use panel 1.
Thanks a lot, but could you please answer me again. How i will know what kind of LCD panel in my Polaris and which number i should use?
these parameters is placed in my start-up file for the haret launcher
#alloctest 0x2000
set RAMSIZE 0x08000000
set MTYPE 1723
set KERNEL zImage
set initrd initrd.gz
set cmdline "board-htcpolaris.panel_type=1 pm.sleep_mode=1 mddi.width=240 mddi.height=320 no_console_suspend clock-7x00.mddi=0xa51 hw3d.version=1"
boot
can i use panel type from here?
i have opened this polaimg-panel3-320-froyo-07-07-10.nbh file in NBH editor and saw that the HW3D is set in Eclair. Should i change this to Froyo or left as is?
Thanks a lot for the conception)))
pannel type 1...
Did I brick my Polaris?
Well, it makes me laugh looking at the last post dated back July 2010 but I decide to post anyway because I feel somebody might have passed through my problems and might help.
Following indications on this forum:
1. I downloaded:
- Kernel: polaimg-panel3-240x320-2.6.32-froyo-09-09-10_21.nbh
- Last build: Incubus26Jc's Super FroYo RLS16 All Languages
2. Put last build (androidinstall.tgz) on SD card in directory /andboot
3. Used RUU Update Utility to flash the nbh file
Everything when smoothly. When it reboots, it vibrates, "Smart Mobility" message shows up, vibrates twice and then a blank screen is displayed.
Going through this forum I think I might have used the wrong type of panel and should have used Panel 1 instead of 3. So I downloaded Windows NBH Editor and managed to change the nbh into Panel 1. Then I shall try again.
This time my Windows 7 is unable to recognize my Polaris and all it can see is a new Disk Drive with no ADB device displayed. So I installed PdaNet302.exe to implement the USB driver for HTC Android Phone but it still cannot see my device and the process aborted.
What worries me is that one step of the process requested to change a setting on the Polaris (On your phone, click Settings > Applications > Development and make sure USB Debugging is on.). Obviously I can't do that as the screen is completely white!
I believe if I can manage to have my PC talking with my device then the problem will be fixed with the panel1-based flash. But every attempt to install the USB driver for Android Phone regularly fails on my PC.
All that time the Polaris remains with the lighted blank screen and there is no way to turn it off as the on/off switch refuses to work.
Shall I buy a new phone? Thanks for your help.
Did you try flashing the phone with a regular oficial HTC rom? just try it. Put the phone in the boot mode (press camera button and another one, dont recall which one) It will change to the tri color screen. Then connect it and try it.
Also there is a modified nbh rom which includes nothing, just the tool to recover your rom. Do a search to the forum.
I recently tried to install on my Polaris and it went really wrong. And finally could recover. The file is called ROMUpdateUtility_task29. I will erase everything on the phone but later you will be able to recover it
Form that point no more experiments. Polaris was made to work with Windows Mobile. It's really unstable, video camera is useless. And so on.
PC Carvalhon rom and I can use my phone as I want.
regards.
---------- Post added at 08:16 PM ---------- Previous post was at 07:57 PM ----------
With this you can recover your phone: http://forum.xda-developers.com/showpost.php?p=6227425&postcount=7160
A second life for my Polaris
Kafkacell,
1. Following your suggestions, I successfully started the bootloader (camera touch while reset), the 3-colour screen appeared, Windows 7 recognised the device. I then flashed the offcicial RUU_Polaris_HKCSL_WWE_3.19.831.3_radio_sign_25.85.30.07_1.59.42.15_Ship and everything successfully completed. With enormous pleasure I see again my Polaris back to activity. Thanks for giving my Polaris a second life.
2. Back to Feb 2009, I flashed a pcarvalho eXtreme ROM. I don't recall any longer the version of this ROM but it was very stable and never ever crashed. Recently I downloaded and flashed most recent ROMs. From that moment on, I have no peace. It crashed 2, 3 times a week. Now I wish I could go back to the old version but couldn't find it. Perhaps pcarvalho removed them to save space? May I ask you which pcarvalho eXtreme ROM version do you currently run. Thanks.
Im currently running 29022 version (latest update from PCCarvalho).
Notes:
UPDATE:
29022 is up
this is a fix release...sound issues should be gone...had to remove htc volume control is it still has issues...fixes minor gfx glitches...updated to lastest and probably final leak version of wm6.5.3 (29022)...will from now on work on unresolved issues and finalize rom...this will still take some time due to work...
updated physics engine and utask app by ultrashot...my thanks to him...
patched htc album to novsync, faster scrolling once cache is made...
removed no longer supported apps (my phone and marketplace)...if u need them install via cab...
Here is the link for the rom: http://forum.xda-developers.com/showpost.php?p=15707730&postcount=8079
it was posted on July of this year, and so far it runs great. The trick is to not install a lot of apps in your main memory. Do it on your SD card. Also a hard reset is a must to avoid all kind of problems.
regards and glad you have your phone back to life
TO ALL PEOPLE:
PLEASE STOP POSTING IN THIS TOPIC ABOUT "THIS PART DOESN'T WORK ECC ECC" WRITE IN THE TOPIC OF THE RELEASE (KERNEL OR SYSTEM), PLEASE LOOK IN THIS THREAD FOR WORKING SETUPS AND TRICKS, AND SEARCH ON THE FORUM BEFORE POSTING!
I start with thread with a information for all users:
Haret system sucks so if you want a full working android system left windows behind you and move to the new android world flash on nand.
With this how-to you will not erase any part of your system but you do at your own risk.
Main problem: screen
For polaris there are 3 type of screen. Usually pola100 (the old one) use panel 1, and pola 200 (09 edition) has panel 3 but ... not always works...
The best mode to test is try to install and after double reboot you have black screen change panel type.
What you need:
phone
sd card (1 Gb or more) 500 mb free
time
Update guide: http://sourceforge.net/apps/trac/androidhtc/wiki/HowToInstallWithAtoolsHaret
reserved by me
Do we have to delete/remove the install-seq.sh after installation?
Are both files (system & data) cleared with the installation script?
Thanks for the help.
install-seq.sh disable automatically after correct install.
This how-to is fir first install on disk on images so it format both data an system.
If you want to make only un update use bsg select partion and select update.
partition
I believe you should make this sticky
Don't post without reading!!!!
This method doesn't use sd partition, it create two imagedisk on sd!
working android
l1q1d said:
Don't post without reading!!!!
This method doesn't use sd partition, it create two imagedisk on sd!
Click to expand...
Click to collapse
hi there,
i made all you told here, booting..after more minutes...the logo appears...but when i press the android logo from the screen.. the touch screen dosent work..i can not start..only with buttons..and after pressing buttons..get over wizard..the phone need SIM PIN..but i can not typed.
please help
i changed BORAD PANEL in 1,2,3 and in 2,3 is black screen.
please help me
You have to disable pin code before installing.
For the screen problem look in kernel thread...
waiting for not busy
What about "waiting for not busy" - im2c error ?
The only Zimage working for my pola100 it's an old 29-04-10 Version !
I am very disperate!
Bye !
touch screen dosent work
foxct2005 said:
What about "waiting for not busy" - im2c error ?
The only Zimage working for my pola100 it's an old 29-04-10 Version !
I am very disperate!
Bye !
Click to expand...
Click to collapse
Dear All,
i tried and deactivate the PIN of sim card..read all posts from previous thread that you gave me..but nothing..
all ok..
bootin..starting..apears the logo and final...
before i need to press the screen, appears a message ''Android system stop responding..and a button FINISH"...after pressing finish, i need to press the middle of the screen on the android logo and nothing, only 2 buttons Emergency Call and Choose Language. to can press these 2 buttons, i use the buttons and i can press them..but touch screen do not working.
please all of you..the masters of this softwares..give me a solution.
thx
Try to reinstall the system...
(rename /andboot/install-seq-disabled.sh to /andboot/install-seq.sh and boot)
touch screen problem
l1q1d said:
Try to reinstall the system...
(rename /andboot/install-seq-disabled.sh to /andboot/install-seq.sh and boot)
Click to expand...
Click to collapse
hi there..
i solved the problem..i took an older Z image..and working fine
the problem is that more applications like camera..media player screen adjust don't work..
they try to run..(i mean ..in camera..i can see..but appears a messages with stop working..sorry). i don't know why..
nothing work well
and what about the contacts..how can i get them from my Sim card?
i don't know..
if you can help me will be great.
thx allot for yours assistance.
best regards.
The information from sim card are very limitated (neither pin code works) so if you want to export contact sync before starting with google and configur your google account on android.
old zimage are full of bugs and all developers install android on nand so starting android from haret has many unfixed bugs.
I've been playing around with the haret install for a week or so now, and I've found that, for me at least, it makes a huge difference which initrd.gz file I use.
The one dated 22-05-10 doesn't let me install any zImages newer than 29-04-10. After trying all sorts of combinations of base files with different dates (haret, zImage) and additions to the default.txt, changing the initrd.gz file to the one dated 20-02-10 fixed most of my problems and lets me install the most recent zImage files without a glitch.
No clue why, just that it works.
I'm running a Pola100 with the original WM6.0 ROM still on it, and radio version 1.58.25.14. Yeah, I need to upgrade to at least the official WM6.1 ROM and probably something better. But I'm a newbie at this, so I need to work up some courage first ;-)
hello,
I tried to install android on sd following your instructions, everything seems to go well until the screen where it says:
"Welcome to htc vogue Frøya
touch the android to begin "
I'll try, but the touch does not work, I tried using the d-pad, which does work, but I can only select the language and the emergency call.
zImage as I used: zImage-Frøya-15-07-10
androidinstall.tar as I used: Incubus26Jc's Super Frøya RLS11 Themed
please help me because I would switch to Android!
thanks
Try with latest kernel version on kernel (i release it yesterday)
l1q1d said:
Try with latest kernel versin on kernel (i release it yesterday)
Click to expand...
Click to collapse
where can I find it?
thanks
I tried it unsuccessfully. Boot starts regulary, always ending on repeating error, looping forever.
I can read something like:
==============
ERROR no local apt for prog ... replying anyway
...
Setting function 4 for gpio ... that I don't own
==============
Is it related to which system file ? Loader? Kernel ? Or what ?
Thanks
What did you use for your installation?
I used the files mentioned at the very beginning of this post.
Regarding zimage: zimage-24-05-10
Hello All,
Does anyone have an working version of XAndroid working on HTC Touch Pro,that wifi, camera and gps works on? I downloaded 2.2.1 xr03 and no wifi,no camera,no gps. The 'look' looks great, I have to say. Also what is everyone getting on battery life that has used recent versions of XAndroid on HTC Touch Pro?
Thank You,
Barry
I'm using the XDANDROID version 2.2.1 (frx04) and wi-fi and gps work, but the camera doesen't work. If you want, you can whatch this site : h**p://xdandroid.com/wiki/Downloads
hackerino,
Thanks a bunch for the info. I updated my Touch Pro from (frx03) to (frx04) today but still cannot get wifi to work. This is the first time I have run a 'patch update'. It appeared to go correctly at bootup,,as I got the package icon thing. It took about 5 mins to update,then rebooted back into WinMO. Is this correct? reason I ask,is,in reading the update procedure it should do the update routine,then delete the actual update.zip file. My update.zip file is still in the andboot directory on my SD drive.
I have the PPC6850 HTC Touch Pro phone. Is this the same model TP you have? I am running WinMo 6.5 that is an almost one year old image,from here. I wonder if running WinMo 6.1 versus WinMo 6.5 can have any effect on initializing the devices for XDAndroid to hook into?
I am using the RAPH800 startup.txt file. using the RAPH startup.txt file my device hangs at 'reading sd card' at a certain point.
Thanks again,
Barry
I'm using the latest kernel package from the Autobuild site and I am staring at 5 wifi spots as we speak. Keeping in mind I have a Fuze/RAPH110 and I occasionally get the waiting on SD card message but it passes after a few seconds.
Link to the Autobuild site: CLICK HERE
In addition, I am using the system.ext2 partition for FRX04. I am not sure if it matters which one you use (the system.ext2 file or the OTA update) as long as the system.ext2 you are updating from is an original, unmodified signed system image.
Do leave us some feedback HERE, thanks!
n-Joie! (Enjoy)
Hi all,
I am not starting this thread without doing my research.
I have installed few android versions (some will install and some won't). And the one I was able to install were not fully functional. They were either alpha or beta versions.
I can do with either 2.1, 2.2 or 2.3.
Can someone please tell me if there is a version out there that I can install and work perfect or near perfect on my HTC Touch Diamond?
I have been trying to search this forum and everytime I come accross a perfect version, it won't load on my phone. I am not sure what am I missing.
Hope someone understand where I am coming from.
I can describe where I am getting stuck etc as well.
Cheers
SB
stuck
I have just installed FroyoBV6
1. my device is: HTC Diamond
2. I'm using kernel: Default from Froyo B-V6
3. I'm using Ver: Froyo B-V6
4. the problem is: my phone is not going past the initital animation. I have rebooted and ran Haret.exe several times now.
Any ideas..????
I want a version that can let me use -
- WiFi
- 3G
- Camera
- 2G
- Market
- downloading on my SD card...
- GPS/Google map
Anyone who has tested or is still using anything similar to this on their HTC touch Diamond, please let me know...
Have either of you checked out this thread for known issues?
http://forum.xda-developers.com/showthread.php?t=1178546
A Small Query Regarding Andriod Installation on HTC Touch Diamond
Hi All,
I have a small query.
I am trying to install Andriod on my HTC touch diamond after reading from threads, the query is that where exactly i have to dump the extracted files. what is meant by "Internal storage"
If i place it in Internal storage i.e the 4GB one and try to run "haret.exe" its says that "cauld not read trailer"
and if i am trying to place it in the root folder i.e "my device" in parallel to "windows", "program file" etc its says not enough disk space. when i checked the memory available its less and data is larger... and just to be clear that HTC is not having data i already did a hard reset and removed my all data.
can you please help me.
Thanks!!!
small problem
i downloaded xdandroid for htc touch diamond...but while booting it shows "cannot find rootfx file on sd card,extracrt it"
but when i try to extract in mobile r laptop it shows...operation failed,i used many software to extract but no use...
pls tell me how to extract it...??
thanks..