Everyone,
I've written this a bunch of times but and putting it in
it's own thread so folks can read and use it.
Memory and Storage:
/sdcard -- internal memory of the tablet
/sdcard2 -- microSD card in the external slot
/usbdisk -- USB key slot
Stock Recovery Info:
Main method: Put your recovery folder and update.zip on /sdcard, turn off the tablet, the press power and volume + to initiate standard recovery.
Second method: Put your recovery folder and update.zip on a microSD card. Edit the command file in the recovery folder with Notepad to change the location from /sdcard to /sdcard2 and save it with the name "command" (NO
.txt or other file extension). Then boot recovery with power/volume + and the OS will use the sdcard (assuming you don't have a live recovery/update.zip file in /sdcard).
Third method: If you can boot recovery to CWM but can't get your ROM to work, go in recovery to the mount menu and go down to the mount USB memory option and choose it. Then plug your connector cable from the miniUSB port to your PC. When you plug into your PC an Explorer window should open and you should have a drive letter representing the G-Tablet (it's G: on mine) on your menu. You now can select that letter and you have access to your tablet memory (/sdcard). I've even had a time or two when not a single file showed!!! I added update.zip and recovery and loaded
a ROM!
The tablet boot process apparently checks /SDCARD. If it doesn't find a recovery file there it does the same check if you have a miniSD external card installed. The large USB slot is not useable for booting or recovery so far as I have determined or read.
I hope this helps you.
Rev
EDIT: I didn't put one fact in here about recovery that everyone should know. When you run a recovery operation, the system deletes the command file so you can't accidentally do it again. If you have to run a recovery or
attempt to load something again, make sure you have a command file in the recovery folder with the correct command in it!!! Sorry I omitted this first time around.
Placeholder
Placeholder
Hope everybody who needs this has seen it. I won't kick it up again.
Rev
Can you also add information about partitioning of /sdcard and why would one need it?
Is there another "hidden" flash memory available for firmware or all mods and custom ROMs go into /sdcard only?
Thanks so much, I thought I'm dead cuz I wiped out everything.
This may have been asked before, but how does one perform a full data wipe w/o using CWM? Thanks.
HackaMathecian said:
This may have been asked before, but how does one perform a full data wipe w/o using CWM? Thanks.
Click to expand...
Click to collapse
You need to use nvflash (nvidia tegra SoC flashing utility). There are alot of posts about it. Do be carefull if you go this route, as even though you will not damage your tablet, it may be difficult to put it back to a bootable state if you don't do it properly.
thanks!
thanks great. simple and to the point. should help people that get confused. thanks again!
Vlad_z,
It has been my experience that when somebody gets boot loops, it often involves a
partition problem. Also, sometimes the G-Tablet does flaky things. I have one I
just shut down. Restarted it with boot looping and had to rebuild.
The three locations listed above are the three memory places you can store stuff
unless you find software that custom sets up something else.
Rev
Os Money:
http://forum.xda-developers.com/showthread.php?t=861950
This thread completely explains the NVFlash process.
Rev
That's kind of odd, my removable sd card ended up with the label ex-sd. Doesn't seem to be messing anything up though.
sixtofive,
I've never seen or heard of that with the stock ROM. Are you running a different ROM?
Some of them do change the directories.
Rev
So simply put, we should copy and backup the recovery folder and update.zip in /sdcard (or tablet storage) and when things get f'ed up, we move the recovery folder and update.zip back into the /sdcard?
Maybe it's just me, but I looked into the recovery that was already in the tablet and there's nothing in it; is that normal? If not, can anyone provide the back up recovery folder and update.zip just in case?
sam,
Recovery is simply a folder which holds a file named "command" in it. Command is a file
that has the command line in it with the command and parameters to "recover" or "load" files onto your G-Tablet.
Sometimes when your tablet gets messed up, you can still use recovery and are lucky. But sometimes the recovery partition gets damaged and then you have to look
for other ways to get in and fix things.
http://forum.xda-developers.com/showthread.php?t=1010943
Many of us keep telling people there is a lot to learn here -- and Android doesn't have
all the stuff built into it Windows does. Nor is Android known for it's great documentation!
If everyone would read all the stickies at the start of the forums, it would provide
probably 80% of everything they need to know.
Rev
If OP also put links to stock ROMs, that would be great
interesting...even though I don't have a microSD card in mine /sdcard2 seems to be a valid directory within "root explorer"
what partition and memory structure should I be seeing on my brand new g-tablet? any suggestion on "mount" and "df" output?
Question, which is the best method or quicker to backup before attempting other rom installs?
Deleting CWM
How would one delete CWM so that the tablet can be returned?
Got my gtablet last evening. Seems there is a lot to learn.
thanks butchconner...
Thanks all the people who are contributing at xda. You are doing a wonderful job. In fact I bought this device because of you ( I think Viewsonic owes you guys a lot. At least they avoided a big loss because of you. )
Two questions:
1) Is it recommended to flash back to stock before changing roms?
2) Is there a link to the stock Rom files that I am missing?
Thanks
Related
I tried a quick search but it looks like everyone else here is at least smart enough to get past the first step.
I was attempting to follow the quide for clockwork and tnt however the clockwork file automatically downloads to my tablet memory instead of my sdcard. It seems like this is because my tablet memory file is labeled sdcard which auto labels my actual sdcard "sdcard2". I tried to rename the folders (wouldn't let me) as well as copy and paste clockwork via my PC but I can't see the sdcard on the PC. I tried mounting and unmounting the card and turning off the tablet but nothing seems to work.
So here I stand...finally choosing to root this thing and my idiot self can't even download the file!! Ha!
Feel free to give me a very hard time while also helping me out. I can take it.
I don't claim to be an expert, but you are right. The drive in the tablet is sdcard. The external card is sdcard2. And a USB drive plugged in is USBdisk.
If you are trying to burn ClockWorkMod, you will have to bring up the Recovery file on your PC when you un-RAR it -- open the "Command" file in something like Windows Notebook -- and edit the sdcard address reference in the command line to sdcard2 -- then save it and put it on your external card. You should have two files on the external card -- a Recovery folder and "Update.zip".
Then shut down and reboot holding down the Power Button and Volume + button. Should load by itself after that.
I offer the usual disclaimer about doing this at your own risk. Sometimes things go wrong even when you do it right.
I have been trying to save you time and grief -- but you also might be smart to search and read the many other threads on these forums about CWM installs.
And by the way -- I hope you are install CWM 8. I hear there are problems with the other version. Again, read!!!
Rev
Hello all, I have been lurking for about 3 months. I have usee the information found here to not only keep my gtab (it was so horrid when I got it almost took it back tbe same day. But keep it from hitlting the wall whenI get so pissedat it. The information i get here is easy to understand and easy follow.
But I seem to be at an impass. I want to install TnT lite from my microsd card but I seem to be doing something wrong
My intent is to wipe ALL the data on the device. But I dont want to do that till I know I can install TnT lite 4.2 fromthe micro sdcard.
When I boot to clockwork the only option I see is "install from sdcard" meaning the internal sd.
I have put the recovery folder in the root of the microsd. I have made sure that the command file says "sdcard2". I have removed from update zip from the sdcard (internal) and made sure the update zip file in also in the root of the micosd. But clockwork mod dose not see it.
I have searched the forum looking for more comprehensive idea onhow to do it from microsd but I have not seen anything. If I missed a step or looked in the wrong place let me know.
I can not start a tbread in the dev area so I hope I can find some help here.
The wall is starting to look like good place to slam this thing
Hi,
I think that when you use the update.zip and /recovery/command file method, that's with the STOCK recovery. CWM *replaces* the stock recovery, i.e., you either have stock recovery OR CWM, on your Gtab. That's why both get initiated by pressing the same key sequence, power pls Vol+.
So, if you want to flash using an update.zip and recovery/command (modified to pt to /sdcard2), you'll need to get stock recovery in your Gtab.
You can get stock recovery by flashing one of the newer stock TNT versions, e.g., 3452. That replaces CWM in the recovery partition, as part of the flash. Then put your desired update.zip and modified recovery/command on /sdcard2, power off, the power plus Vol+.
Jim
Thank you! That helps.
Hi,
I'm not sure if this helps or not, but you can mount USB in clockwork. So you could wipe all the data, partition and everything, then mount the USB, copy the rom over from your PC to the internal storage and flash it.
If you decide to use clockwork, make sure it's the .8 version that you can get from the first page of the tNt Lite thread.
nbowes said:
Hi,
I'm not sure if this helps or not, but you can mount USB in clockwork. So you could wipe all the data, partition and everything, then mount the USB, copy the rom over from your PC to the internal storage and flash it.
If you decide to use clockwork, make sure it's the .8 version that you can get from the first page of the tNt Lite thread.
Click to expand...
Click to collapse
That is great news. Thanks!
I just got my g-tab in (not a w00t purchase, ebay in fact)
I'm reading over scsione889's very awesome guide before I dive in. While I was reading the guide I note that it very specifically instructs the reader to flash from internal memory.
I found this to be rather odd since all my experience with clockwork on my dInc has been flashing from SD. Does anyone have any details on why flashing from internal memory is used in the guide?
Question number two comes from the w00t purchasers warning thread
I checked my stock firmware version after reading this thread and it's 1.0-2736. Why is it necessary to install the OTA before flashing other roms etc? Does it update the kernel? It certainly can't be a radio issue on this tablet =P
I have already installed clockwork at this point and I wanted to ask about this before performing the OTA or just flashing Vegan. Any tips on the OTA thing?
Hepful posts will as always be thanked!
After investigating a bit it seems like the G tab handles it's own internal memory as an SDcard. This strikes me as odd but may be normal. Will clockwork not detect a "second" SDcard?
More info would be great if anyone has it.
k4el said:
After investigating a bit it seems like the G tab handles it's own internal memory as an SDcard. This strikes me as odd but may be normal. Will clockwork not detect a "second" SDcard?
More info would be great if anyone has it.
Click to expand...
Click to collapse
All the devices I've owned has the 'internal' memory labelled as SDCARD, even though it's not actually removable. When flashing roms you will be copying the files over to the internal memory (labelled on the device as sdcard).
Your legitimate sd card is usually labelled as something else. /emmc, etc etc. It will likely depend on the rom/kernal you are using.
k4el,
Internal memory is /sdcard. External miniSD card is /sdcard2.
You can flash by putting the appropriate recovery and update.zip files in /sdcard and
booting into recover with power and volume +.
You can also flash by putting the same to files on a miniSD card and putting it in the
slot. Only thing is you have to edit the command file in the recovery folder to change
the location from /SDCARD to /SDCARD2. (You can do that with Notepad, but make
sure when you save it you keep the file name as "command".)
Your USB key shows up in the file manager as "/usbdisk" but it is not usable for booting
or recovering.
I think there is a pretty good sticky on this topic at the beginning the General Forum.
Rev
Standard recovery can use a microSD for flashing (the instructions are slightly different, as Rev mentioned) but the "safe" version of clockworkmod we use only reads off the internal memory only. Newer versions on cwm can use both, but they is a higher risk of to causing a soft-brick so I personally don't recommend them.
Hi guys, i'm in desperate need of your help. i think my precious o3d might have been screwed.
first let me tell you what i did. as you know the internal sd card of o3d is 5gb or so and it fills up very quickly. this internal sd card is mounted as /sdcard. i have a class 10 16gb micro sd card and when i insert it, its automatically mounted as /sdcard/_ExternalSD. The applications or games, especially the ones that have external data folders which are like 1gb in size insists to be installed on /sdcard. You can't move those data folders to _ExternalSD, because then the apps doesn't work.
Then i came across this topic:
http://forum.xda-developers.com/showthread.php?t=1189701
As you can see that was exactly what i needed. I had CWM 5.0.2.0 installed so i downloaded the first .zip then copied all of the files and folders excluding the _ExternalSD folder to the external sd card then rebooted into recovery. From there i flashed the zip and rebooted again. phone booted up and all was ok and it worked. now the phone sees the external sd card as the internal one and the internal sd card was mounted as /sdcard/_ExternalSD. I then formatted the internal sd card from the settings menu because i already copied all of the stuff there to the external card. It worked fine and the internal card is formatted. After that i decided to get a nandroid backup so i opened the rom toolbox program. From the menus i selected the backup option, gave it a name, clicked ok. the phone rebooted into cwm recovery screen but nothing happened. then i noticed something was not right because there was some error lines under the cwm menus saying "E:can't mount CACHE:recovery/command" etc. Then i selected the reboot phone option but the phone rebooted right back into the CWM recovery again!! At that point i knew that i was @#?^ed.
Anyways i researched a lot and came across this thread:
http://forum.xda-developers.com/showthread.php?t=1156549
i did exactly what he said and it worked, i mean it flashed nicely. then i rebooted the phone but it booted into the recovery again!!! But this time the CWM recovery was gone and i believe this is the stock recovery screen. I can browse the menu of it and make selections but the phone boots into the recovery every time it reboots.
The recovery screen looks like this:
http://farm8.staticflickr.com/7010/6654644033_b616bc0635_z.jpg
Then i flashed the phone to the latest official firmware V21A_00, it flashed nicely but it still boots right into the recovery everytime.
Then i installed the Android SDK and tried to push the original vold.fstab file to the system using the adb command line tool but it doesn't see the phone. I think adb works only when the system boots up normally, not in the recovery mode.
I don't know if there's a way to install the CWM from the stock recovery somehow. If you know how, please tell. The CWM has more options.
I don't know what else i can do. It started to look ridiculous. If there are any experts cool enough to help please do so. I'll be waiting. Thank you...
Edit:
I also tried this:
http://forum.xda-developers.com/show....php?t=1244490
I starts just fine but get's stuck on the "RESET" command, after a while it gives "DOWNLOAD FAIL!" error. I think the phone is supposed to restart automatically but it doesn't. Manually resetting the phone doesn't work either.
I'm about to pull my hair out...
Edit 2:
I also posted on the official LG Mobile forum here:
http://www.lgforum.com/forum/boards...d-goes-into-recovery-mode-every-time-it-boots
Fingers crossed
Quite a post!
From all your post there is no mention that you formated and did a factory reset after 21a flash.
Can you please try that if you haven't?
Sent from my LG-P920 using xda premium
thank you for the reply!
i tried all 4 wipe options on the recovery screen then rebooted. it's the same, i'm back at the good old recovery again
Did you try with the external sd card out?
This is strange, usually a kdz flash coupled with a format fixes the problem.
Some how it still can't find the internal SD card.
I don't have further recommendations. Sorry
Sent from my LG-P920 using xda premium
yes i tried with the external sd card out. it didn't work..
vpamir said:
yes i tried with the external sd card out. it didn't work..
Click to expand...
Click to collapse
Hopefully someone else on this forum can suggest a way for you to unbrick.
your problem is although you have reset your phone, somehow it can't find a partition to boot from.
or
somehow the KDZ flashing is not totally successful.
good luck
If only there could be a way to be able to use the adb command from the Android SDK then i might be able to restore the vold.fstab file to its original, if the problem is that at all. Maybe then it'll work. To be able to flash the CWM Recovery again somehow might be a good thing too because it has more options like flashing .zip format roms but i have no idea how. Does anyone know if the stock recovery can flash some specifically named file to the system, does it have that kind of functionality? I'm desperate, please share your thoughts.
.............anyone?
I am sorry to say that but there is no solution for this problem yet. I have done the exact thing that you do and tried every single solution with no luck. The only way is to send it to lg repair service. My solution was to replace the mainboard.
Dostum gecmis olsun malesef tek cozum yolu anakarti degistirmek. Uzaman sayilirim android konusunda bosuna ugrasmayasin diye soyluyorum. LG servisi bile anca anakarti degistirerek cozum sunabildi. Temel problem internal karti formatlamis olman. Partititon table'i bozuyor bu islem malesef ve bu yuzden hicbir yontem ise yaramiyor.
Gecmis olsun tekrar...
so you say that the main problem was to format the internal sd card? well if formatting the internal sd card bricks the phone then why the hell is there an option to format it in the settings menu?
well if you didn't apply the swap fix, it wouldn't be a problem to format. When you swap the sd cards and format, it is the problem.
crime_of_heart said:
well if you didn't apply the swap fix, it wouldn't be a problem to format. When you swap the sd cards and format, it is the problem.
Click to expand...
Click to collapse
so you did exactly the same thing as me right? i mean you applied the swap fix then formatted the internal sd?
replacing the motherboard to fix this seems to be a bit nonsense to me to be honest. what does the partition table have anything to do with the motherboard?
if only there would be a .kdz format custom rom which factory resets the internal sd card during the flash process and maybe fixes the bootloader somehow, that might be the solution.
yes i did the same and the only solution was to replace the motherboard. we need a sowftware that can reach to the emmc in low-level. like omap flasher. but we also need the correct drivers which doesn't exist yet.
crime_of_heart said:
yes i did the same and the only solution was to replace the motherboard. we need a software that can reach to the emmc in low-level. like omap flasher. but we also need the correct drivers which doesn't exist yet.
Click to expand...
Click to collapse
i don't know what the emmc is, i need to do research on that. but i still think that replacing the motherboard won't solve this issue because it seems non relevant to me. i messed up with the vold.fstab file. but after that it worked fine. i mean the internal and external cards swapped just fine. only after i decided to make a nandroid backup using rom toolbox all hell broke loose. i plan to wait a couple of days before turning the phone to LG service. i believe someone will come up with an idea.
yardım etmeye çalıştığın için teşekkür ederim bu arada
Well, there´s a new recovery for the O3D, v5.0.2.7 (I got it with ROM Manager).
It fixes 2 bugs of the previous (5.0.2.0) version: now the USB mass storage option in the mounts menu works (mount external SDCARD), and we can use ADB while in recovery. That way we can fix stuff in the phone filesystem while in recovery: we can now use ADB shell, or ADB push to replace files.
The problem is that I don´t know how to flash it to the phone while in the stock recovery. If someone can guide me on creating a signed ZIP containing this new recovery, flashable in the stock recovery, I would be glad to do that and post it here. I think these phones of you guys can be fixed using this method!
Marcovecchio said:
Well, there´s a new recovery for the O3D, v5.0.2.7 (I got it with ROM Manager).
It fixes 2 bugs of the previous (5.0.2.0) version: now the USB mass storage option in the mounts menu works (mount external SDCARD), and we can use ADB while in recovery. That way we can fix stuff in the phone filesystem while in recovery: we can now use ADB shell, or ADB push to replace files.
The problem is that I don´t know how to flash it to the phone while in the stock recovery. If someone can guide me on creating a signed ZIP containing this new recovery, flashable in the stock recovery, I would be glad to do that and post it here. I think these phones of you guys can be fixed using this method!
Click to expand...
Click to collapse
Great news! But now i need to find a way to install the new CWM. Just as you said i believe what i need is to find or make a .kdz update which includes this new CWM.
What do you think?
I know this is possible, at least for the Galaxy Ace: I have a ZIP file for this device with a custom recovery image, flashable in stock recovery!
To make one for the Optimus 3D, I need to know the following:
- How can I obtain the .IMG of the new recovery? I have found some temp files in clockworkmod folder in my sdcard. The creation date of one of them matches the exact moment I upgraded my recovery, and the file size also matches a recovery image: 5.54MB. Is it the recovery image? Can I just rename it to recovery.img? How can I extract it to ensure it´s ok?
- After I get the recovery image, I can use the Galaxy Ace ZIP as the base to build the O3D zip file. Any help on what do I have to change to make it work correctly?
I also tried this:
http://forum.xda-developers.com/showthread.php?t=1244490
I starts just fine but get's stuck on the "RESET" command, after a while it gives "DOWNLOAD FAIL!" error. I think the phone is supposed to restart automatically but it doesn't. Manually resetting the phone doesn't work either.
I'm about to pull my hair out...
Edit: I'm 99% sure that this isn't a hardware related problem. And LG's software not being able to turn the phone to stock is totally [email protected]#$%!
On some "unbrick your optimus 3d" threads i came across this image:
http://attachments.xda-developers.com/attachment.php?attachmentid=667470&d=1311752328
i tried all methods around here but not once i came across a screen like it. weird...
well i give up guys. so much technical [email protected] going on and no one seems to understand this device enough. i'll turn it to the LG Repair Service today. Thank you everyone for your help...
(Now, I know this is not in the right section or even in the device's page, but...)
Forewarning: I am NOT responsible for any damages caused by running this tool. (You ran it, not me.) Also, do NOT use on the Thrive 7 or ANY of the Excites! The Thrive 7 has an entirely different bootloader/partition layout than the 10.
Pio_masaki and I have been working hard for almost a year to get root on the ICS version of the Toshiba Thrive 10.
Last night, I was able to finally sneak past sealime.ko and have it work.
It uses the "root any ICS device" tool, with special modifications specifically for the Thrive 10.
(can't post any links, so it's on the "thrive-hackers" github page.)
Special note: While it is set up for OSX ADB, I have not been able to find any binaries.
Are you saying that we are close to a root method for Thrives running Toshiba ICS?
rohads said:
Are you saying that we are close to a root method for Thrives running Toshiba ICS?
Click to expand...
Click to collapse
Saying there is a method to root it now, yes, we got around sealime.ko. This means we can flash the HC bootloader which is unlocked, which allows custom recovery and kernels/ramdisks (boot.img) to be used.
BTW the link is https://github.com/Thrive-Hackers
congrats guys ! very awesome work !
jdsingles deodexed ROM w/ agat63's 1.3 kernel Suped up w/ CB 6.26.13
More specifically, it bypasses sealime to flash the unlocked bootloader. What we did was we MVd /dev/block/mmcblk0p6 to 0p9. It's a pure fluke Pio and I found out that it works. We found out that sealime was explicitly blocking write to 0p6, so he semi-sarcastically said to move it. I ran the mv command, whadda ya know? It worked!
'Course, getting the tool completed wasn't as simple as that...
PS: Could we get this moved to the Toshiba Thrive Development section?
Have instructions been written for the process?
worked for me
I used this tool on Jul 8 and it worked very well. I got it from thriveforums dot org. Thank you pio_masaki and AmEv.
I tried changing the recovery to the latest TWRP using "fastboot flash recovery twrp-2.4.1.0.img" while in bootloader. I was not able to, though as it kept giving me errors.
Does this bootloader not allow flashing a recovery? I noticed the rootme script uses adb commands to push the CWM recovery.
I am now running Dale's latest deodexed rooted ICS rom with the CWM recovery he included.
Other unrelated lessons learned:
If you can't mount your SD card in recovery, try a different card!
And, Dale packages his update.zip inside the downloaded zip file!
navyguy said:
I used this tool on Jul 8 and it worked very well. I got it from thriveforums dot org. Thank you pio_masaki and AmEv.
I tried changing the recovery to the latest TWRP using "fastboot flash recovery twrp-2.4.1.0.img" while in bootloader. I was not able to, though as it kept giving me errors.
Does this bootloader not allow flashing a recovery? I noticed the rootme script uses adb commands to push the CWM recovery.
I am now running Dale's latest deodexed rooted ICS rom with the CWM recovery he included.
Other unrelated lessons learned:
If you can't mount your SD card in recovery, try a different card!
And, Dale packages his update.zip inside the downloaded zip file!
Click to expand...
Click to collapse
Try fastboot flash:raw.
Is there any need to do a backup before rooting?
TubaMeister said:
Is there any need to do a backup before rooting?
Click to expand...
Click to collapse
Not explicitly, but it wouln't hurt in case your tablet got into contact with allspark.... er, the bootloader didn't flash, and you're stuck in a bootloop.
easy root and CWM recovery
walk thru
http://www.youtube.com/watch?v=MXeYJhKCgX8
adb driver
http://www.thriveforums.org/forum/t...vers-usb-adb-driver-installation-package.html
root tool
https://github.com/thrive-hackers/thrive-10-inch-ics-root,
follow this to install CWM
http://www.thriveforums.org/forum/d...0-clockworkmod-touch-recovery-v6-0-1-1-a.html
follow to install touch CWM
http://www.thriveforums.org/forum/d...0-clockworkmod-touch-recovery-v6-0-1-1-a.html
ROMs
http://www.thriveforums.org/forum/dalepl/
Uh oh
robyn402 said:
walk thru
http://www.youtube.com/watch?v=MXeYJhKCgX8
adb driver
http://www.thriveforums.org/forum/t...vers-usb-adb-driver-installation-package.html
root tool
https://github.com/thrive-hackers/thrive-10-inch-ics-root,
follow this to install CWM
http://www.thriveforums.org/forum/d...0-clockworkmod-touch-recovery-v6-0-1-1-a.html
follow to install touch CWM
http://www.thriveforums.org/forum/d...0-clockworkmod-touch-recovery-v6-0-1-1-a.html
ROMs
http://www.thriveforums.org/forum/dalepl/
Click to expand...
Click to collapse
I installed the drivers, used the root tool, the restore was successful, but now the tablet is stuck in a boot-loop mode.
The root tool was running, there was a line that said the screen would go blank, which it did, and it stayed there for several hours. When I came back to check on it, the tablet was off, so I turned it on. That's when I found the boot loop. It'll get to the home page, tell me that nova launcher has stopped, then loop back to the moving stars section of the boot screen.
Any ideas on what to do now?
DLeach4512,
if CWM is still alive, so just flash any ROM via CWM (flashing wipes all your data that exist in internal memory, so you need to make backup via CWM if you wish to save your data; and after flashing ROM you can import all data via Titanium Backup)
Kyonex said:
DLeach4512,
if CWM is still alive, so just flash any ROM via CWM (flashing wipes all your data that exist in internal memory, so you need to make backup via CWM if you wish to save your data; and after flashing ROM you can import all data via Titanium Backup)
Click to expand...
Click to collapse
You know, I feel kinda dumb because I didn't even try that!
Now i've tried it, and I see I can get into CWM.
I put a ROM on an SD card on my PC, then put that SD card into the Thrive and used CWM to install the .zip of the ROM I selected, and it won't install. It starts, then it says Installation aborted, but won't tell me why.
Any ideas where I should start unraveling this mystery?
1. check that your recovery is CWM and not stock recovery
2. check that you put on SD archive that contain folders named system and META-INF, file like boot.img, something other maybe (many ROMs archive contain "archive in archive", so you need to unpack archive from main archive and than put that internal archive on SD); after checking that all right try to flash that archive again
3. try another sdcard (full sized SDHC + formated in FAT32)
DLeach4512 said:
You know, I feel kinda dumb because I didn't even try that!
Now i've tried it, and I see I can get into CWM.
I put a ROM on an SD card on my PC, then put that SD card into the Thrive and used CWM to install the .zip of the ROM I selected, and it won't install. It starts, then it says Installation aborted, but won't tell me why.
Any ideas where I should start unraveling this mystery?
Click to expand...
Click to collapse
also make sure you open the zip and place the update.zip on your card -
From my GSIII - jd's Stock/Rooted/Deodexed 4.3
Kyonex said:
1. check that your recovery is CWM and not stock recovery
2. check that you put on SD archive that contain folders named system and META-INF, file like boot.img, something other maybe (many ROMs archive contain "archive in archive", so you need to unpack archive from main archive and than put that internal archive on SD); after checking that all right try to flash that archive again
3. try another sdcard (full sized SDHC + formated in FAT32)
Click to expand...
Click to collapse
Excellent!
1) I had to extract "update.zip" from the ROM I had downloaded.
2) I re-formatted the card I was using to FAT32 instead of FAT.
3) I was able to get the install started with no trouble after following your directions.
BIG THANK YOU FOR THAT!
I got a successful install message, and then it booted!
Thanks a million!
Problems after Mount Changes
I changed the mount as described on thriveforums.org to allow apks and data to go to the external sd rather than "shared" internal memory.
I now have the situation with less free memory available on the sd card than on internal. The CWM backups went on the physical card- a 32 G one almost full. Will look for a major mfr 64 Gig.
One or so issues with the revised mounts where the external sd card is now internal. They relate to making backups with dalepl's latest CWM 6.0.1: where to put CWM backups for now and are they being made correctly with the revised mounts?
The backup made prior to the mount change looks normal: a single, dated/numbered folder about 2.6 Gb, 6 files: boot.img, cache.ext4.tar, data.ext4.tar, nandroid.md5, recovery.img and system.ext4.tar. However, the one made after the mount change also has a dated, numbered folder of only 15.8 Mb and 7 files: .android_secure.vfat.dup, boot.img, cache.ext4.dup, data.ext4.dup, nandroid.md5, recovery.img and system.ext4.dup. There is a second folder associated with the later bu called "blobs", which is huge --2.76 Gb, 3292 folders and 6581 files. Is this an expected result and any one think it might be a valid bu?
Also, it went on to the external SD (now "internal") and total storage use is now almost 28 Gb out of 30.2. I now have the situation with less free memory available on the sd card than on internal. The stuff there looks ok, pix movies and music plus CWM bups of 5.5 G and App_Backup_Restore archived apks at 2.8 Gb. So, I copied the cwm backups folder to the real internal memory, now sdcard2. I assume this true internal memory might get wiped during a restore so, this is not a valid storage site for this? And, if I put copies on a spare card, will that really work if my downloaded apps are on the original card, eg does the CWM backup copy the external card apps?
As I note, for some reason this 'blobs' folder won't copy easily to a USB via the Thrive or Win 7 pc. It also won't copy to a Win 7 HD partition where I store my Thrive stuff. (Update: I was able to do a wireless transfer to my pc and then, from there, to a spare SD card.)
Any thoughts? Should I go back and change the mounts to default?
BTW, I find FolderMount has no real use with the changed mount on the Thrive unless someone tells me otherwise. With the Thrive mounting the external card as internal, files go to the physical card.
gberpa,
I don't understand your question - it is very long. But I know that custom recovery (CWM / TWRP) itself remounts sdcard and internal memory before wipe process so it will wipe correct memory (only internal memory). If you need to change the ROM you don't need to worry about mounting paths because after wipe mounting paths will be restored to original.
Partition layout of Toshiba Thrive 10.1" ICS
AmEv said:
Also, do NOT use on the Thrive 7 or ANY of the Excites! The Thrive 7 has an entirely different bootloader/partition layout than the 10.
Click to expand...
Click to collapse
Can you give us information on the Toshiba Thrive 10.1" ICS partition layout and their names, please?
We would like to compare it to ours Toshiba Excite Pro (AT10LE-A, tostab12BA). A Dirty Cow enabled KingoRoot has given us a temporary root.
[Q] How Root Toshiba Excite Pro AT10LE-A-108 by dexxxZ
https://forum.xda-developers.com/showthread.php?t=2583677&page=6
Sent from my takee 1 using XDA Labs