SETCPU settings - Captivate General

I got setcpu yesterday and was wondering what profiles/settings people are using?
I've found with the screen off if I keep my minimum clock at 100hz it will freeze so I keep it at minimum 200 Max 400.

i set a profile where my minimum clock was at 200 but i am still getting shut downs. any suggestions?

Please STOP using SetCPU. It does not work so great on 2.2 ROMs.

diablo009 said:
Please STOP using SetCPU. It does not work so great on 2.2 ROMs.
Click to expand...
Click to collapse
I used it for OC's

41LY45 said:
I used it for OC's
Click to expand...
Click to collapse
If u r on a custom ROM, flash a kernel like say glitterballs. Then use the Voltage Controller app to set ur OC and UV (under volt) levels. These are more stable than SetCPU.
When using Voltage Controller, set the settings as "set for now" (this sets them temporary and resets upon boot). Use it for some time, and if u r comfortable with no freeze ups, etc, u can mark them as "set on boot" to make them permanent.

diablo009 said:
Please STOP using SetCPU. It does not work so great on 2.2 ROMs.
Click to expand...
Click to collapse
Thanks for your opinion.

diablo009 said:
If u r on a custom ROM, flash a kernel like say glitterballs. Then use the Voltage Controller app to set ur OC and UV (under volt) levels. These are more stable than SetCPU.
When using Voltage Controller, set the settings as "set for now" (this sets them temporary and resets upon boot). Use it for some time, and if u r comfortable with no freeze ups, etc, u can mark them as "set on boot" to make them permanent.
Click to expand...
Click to collapse
Thanks for the tip.
Swyped from my Froyo-ed Captivate.

I use it on OC kernel for CM7, as Voltage Control is not supported. I have it at min 400 max 1200 and it works wickedly.

adzidek said:
I use it on OC kernel for CM7, as Voltage Control is not supported. I have it at min 400 max 1200 and it works wickedly.
Click to expand...
Click to collapse
Min for captivates is 100. Putting min at 400 would only kill battery faster since the CPU is at 400 instead of 100 when idle.

Related

Mytouch 4g Setcpu Optimization

So I've been searching the forums for a good thread on optimizing setcpu for specifically the Mytouch 4G. I couldn't find one so after i read up on it i created this profile. The tweaks that I've found make this run very fast and gets me easily 18 hours of battery life, and that is with moderate usage. These setting should work for most if not all devices. I don't get any real noticeable lag even when turning the screen on. I'm Using SetCPU 2.1.0 on a Grankin01 Kernel on a Stock ROM, and I'm also using "Autokiller Memory Optimizer" using moderate preset. Hopefully people will post there profiles anyway here it is.
Here is the thread for the Kernel I'm usinghttp://forum.xda-developers.com/showthread.php?t=876848
and here is a link for setcpu basics.
http://androidforums.com/evo-4g-all-things-root/210253-setcpu-guide.html
Alright here are my most recent setting I've been running.
I get around 20 hours of battery life on my phone with moderate use my set CPU settings are
Overclocked to 1.5 ghz minimum 245 ghz
Battery below 30% Max 1 ghz min 245 ghz
Screen off max 245 ghz min 245 ghz
Latest Cyanogen mod Alpha 7.0
I use max 1113 min 245 scaling on demand...screen off min 245 max 350
MT4G + CM7
Pretty sure this is in the wrong place. I guess you read up on everything except where would an appropriate place to post this be.
Sent from my MT4G running Gingerbread
I get 24hrs if I put my phone away! 6hrs on average lol. Cm7 stock kernel. Grankins breaks youtube everytime. Screen off 328 max 248 min. On demand.
Sent from my HTC Glacier using XDA App
With all the CM7 flashing, I get about 12-15hrs with 149760-245760
Sent from my Gridlocks' CM7 MT4G using XDA App
stlouie65 said:
With all the CM7 flashing, I get about 12-15hrs with 149760-245760
Sent from my Gridlocks' CM7 MT4G using XDA App
Click to expand...
Click to collapse
louie i dont know what to make of your preset here... Either you are running your phone incredibly slowly or you have forgotten a 0 on the end and are crazy OCing it...
Have mine set at 76800-1113600 on demand and I demand a lot and average about 8hrs. CM7, zinx kernel,with superpower.
I've been trying to get profiles and triggers down except I use CPU tuner inserted of setcpu. Is it possible to over clock yet still save battery? I doubt that somehow lol. If anyone can post full settings that save battery but still runs well I'd appreciate it. Ill copy one of you guys.
Questions though. What is all the governor stuff like performance, conservative, on demand, etc? What are the thresholds? What are the min max standards? Like if I have 300 and 1500, which does it user and why? Those are the only things I can't grasp
Sent from my HTC Glacier using XDA App
xFate said:
I've been trying to get profiles and triggers down except I use CPU tuner inserted of setcpu. Is it possible to over clock yet still save battery? I doubt that somehow lol. If anyone can post full settings that save battery but still runs well I'd appreciate it. Ill copy one of you guys.
Questions though. What is all the governor stuff like performance, conservative, on demand, etc? What are the thresholds? What are the min max standards? Like if I have 300 and 1500, which does it user and why? Those are the only things I can't grasp
Sent from my HTC Glacier using XDA App
Click to expand...
Click to collapse
Check out this link it has all you'll need to know http://androidforums.com/evo-4g-all-things-root/210253-setcpu-guide.html
What you want is your device to throttle based on the load being put on it. When you aren't doing much i.e. reading a text it should be clocked at 245760 for example because that's not a demanding task. and versely when you play a graphics intensive app or something, it should use just over the maximum amount of cpu power needed to run the app so the app runs smooth. but wont waste battery by overclocking to 1708800 when only a speed of 1017600 is needed. For this i use "conservative" on SetCPU because it will allow more customization.
My advanced settings for SetCPU are as follow. i haven't use CPU Tuner but hopefully it's similar.
Sample Rate you want kinda low 200000 is what i have and i don't get much if any lag.
Up Threshold is at what percentage of processor usage that the clock speed is increased. for me its set to 60. in other words at 60% load on the processor it will start to increase the clock speed.
Down Threshold is the load percentage where the clock speed will be reduced. i have mine set to 33.
Ignore Nice Load will just ignore nice processes. This includes system i believe. i have mine set to 0.
Grabbed this from a mac forum but it should apply.
"A process's priority is determined with a complex formula that includes what the process is doing and how much CPU time the process has already consumed. A special number, called the nice number or simply the nice, biases this calculation: the lower a process's nice number, the higher its priority, and the more likely that it will be run."
Frequency Step is how much of a jump the CPU will take to meet the load. mine is set low, (12) because most processes and apps wont need a whole lot of boost to run smoothly. For my device on average it will be under 768000 which is what you want and is where the battery saving really comes in. Because the CPU is under-clocked most the time its using a lot less battery but is still running everything smoothly.
A lot of people set there devices to ondemand because it's, "very responsive." although true its responsiveness comes from big steps in clock speed as opposed to the small ones that will most likely get the same job done. i.e. a clock speed of 902400 is more then enough to run the process quickly ondemand will jump to 1708800 to handle the same task.
copied from the above link at android forums.
" * ondemand - Available in most kernels, and the default governor in most kernels. When the CPU load reaches a certain point (see "up threshold" in Advanced Settings), ondemand will rapidly scale the CPU up to meet demand, then gradually scale the CPU down when it isn't needed.
* conservative - Available in some kernels. It is similar to the ondemand governor, but will scale the CPU up more gradually to better fit demand. Conservative provides a less responsive experience than ondemand, but can save battery.
* performance - Available in most kernels. It will keep the CPU running at the "max" set value at all times. This is a bit more efficient than simply setting "max" and "min" to the same value and using ondemand because the system will not waste resources scanning for the CPU load. This governor is recommended for stable benchmarking.
* powersave - Available in some kernels. It will keep the CPU running at the "min" set value at all times.
* userspace- A method for controlling the CPU speed that isn't currently used by SetCPU. For best results, do not use the userspace governor."
Please post in General section, not dev.
Well i changed my setting a little to be a bit more responsive and i haven't noticed a increase in battery usage. I set my max speed to 1516800 and min to 368640 and its running quite nicely.
Anyone else getting good result with the conservative setting?
Keldarr said:
So I've been searching the forums for a good thread on optimizing setcpu for specifically the Mytouch 4G. I couldn't find one so after i read up on it i created this profile. The tweaks that I've found make this run very fast and gets me easily 18 hours of battery life, and that is with moderate usage. I don't get any real noticeable lag even when turning the screen on. I'm Using a Grankin01 Kernel and I'm also using "Autokiller Memory Optimizer" using moderate preset. Hopefully people will post there profiles anyway here it is.
Here is the thread for the Kernel I'm usinghttp://forum.xda-developers.com/showthread.php?t=876848
and here is a link for setcpu basics.
http://androidforums.com/evo-4g-all-things-root/210253-setcpu-guide.html
Edit: I've been using my phone for the last 12 hours I unplugged it this morning and have only plugged it in to pull a screen shots with android commander then unplugged it and my battery is at 53% I've watch youtube, txt, made calls, taken pictures ect, ect normal crap, and its running strong. I've made small adjustments on some of my thresholds but they are mostly similar.
Click to expand...
Click to collapse
What version of SetCPU are you using? In mine I don't have the threshold for down, and my sampling rates are way different. Mine is set as from install at 50000. Running cm7alpha.
Using 2.1.0 and I have all the mentioned settings Bob
bobsbbq said:
What version of SetCPU are you using? In mine I don't have the threshold for down, and my sampling rates are way different. Mine is set as from install at 50000. Running cm7alpha.
Click to expand...
Click to collapse
Sent from my stickie key HTC Glacier using XDA App
Is there a way to change voltage? Frequency rules saves are minumum on cellphones.
I'm using Setcpu 2.1.0 and I'm using a stock OC Kernel from Grankin01 and u have to set the profile to conservative.
NovoRei said:
Is there a way to change voltage? Frequency rules saves are minimum on cellphones.
Click to expand...
Click to collapse
Frequency rules saves do save a lot of battery. Combine with undervolting and memory optimizations and you'll get big saves. But no setcpu is solely for cpu settings.
Whats the most stable speed to run this at?
So far i haven't had any stability issues on the Grankin01 Kernel. They ironed out most the stability issues in the Kernel its self. I do however keep my main profile around 1708800 - 1516800, generally 1516800, and min is set to 368640 and I've had no problem not even a signal freeze or crash. I've also run at 1708800 for most of the day plugged in and no issues other then heat. So i think is up to mostly prefrence.
I'm using a stock rom with bloatware removed and as i mentioned the Grankin01 1.7 OC Kernel.
Here is what I'm talking about. Sometimes the auto detect or something is wrong and I get this screen instead of the one you get. I don't understand why. I change ROMS a lot and I don't know if it is ROM specific or not. I'm currently on the cm7 preview from Zinx. Although I have seen it on other ROMS also as I posted before. Here is a pic.
Ignore the dropcap2 as I had just used it to take the picture.
bobsbbq said:
Here is what I'm talking about. Sometimes the auto detect or something is wrong and I get this screen instead of the one you get. I don't understand why. I change ROMS a lot and I don't know if it is ROM specific or not. I'm currently on the cm7 preview from Zinx. Although I have seen it on other ROMS also as I posted before.
Click to expand...
Click to collapse
Looks like from your screen shot that the profile SetCPU is using is on On demand, interactive or some default. What Kernel are you using? that may be the issue. If not a kernel issue. Then it may be a issue with CM7 and how SetCPU interacts with it. try disabling all your profiles and make sure that your main profile is for sure set to conservative.
Nothing else make a backup and try a different Kernel. Grankin01 has a few great ones and even a CM7 kernel with tunes and tweaks. As well as Gorilla. but id try the CM7 Kernel Grankin01 has first my buddy is running it and hasn't had problems. Just make you do a full backup to avoid a FUBAR situation.
http://forum.xda-developers.com/showthread.php?t=876848 Grankin01
http://forum.xda-developers.com/showthread.php?t=846451 Gorilla
Keldarr said:
Looks like from your screen shot that the profile SetCPU is using is on On demand, interactive or some default. What Kernel are you using? that may be the issue. If not a kernel issue. Then it may be a issue with CM7 and how SetCPU interacts with it. try disabling all your profiles and make sure that your main profile is for sure set to conservative.
Nothing else make a backup and try a different Kernel. Grankin01 has a few great ones and even a CM7 kernel with tunes and tweaks. As well as Gorilla. but id try the CM7 Kernel Grankin01 has first my buddy is running it and hasn't had problems. Just make you do a full backup to avoid a FUBAR situation.
http://forum.xda-developers.com/showthread.php?t=876848 Grankin01
http://forum.xda-developers.com/showthread.php?t=846451 Gorilla
Click to expand...
Click to collapse
You are right it was the main profile was set to on demand and when set to on demand these available options change.
As far as kerenls go I have not had good luck with Grankin CM Gingerbread kernels but he is working on a fix.

[Kernel] [GPL] Sense 2.6.32.21 OC/UV 1.51GHZ (CFS-Smartass-TUN)

This kernel is created specifically for sense roms It will more then likely not work in it current state on any AOSP based rom
Features
Overclocked to 1.51ghz and stable as ever (for most)
added in smartass and interactive cpu freq govs
added in TUN support
compiled v4l2 as modules
many more....
for a full list of changes check the commit log here
Quirks
Smartass wont scaled below 768mhz atm im looking into it stick with interactive for the best overall experience for now.
Source
Downloads:
Build 4​
Awesome! I'll give my feedback as to how it is working.
I did notice once a governor is selected you have to reset your Mhz or it will stay on 806 max. Also this kernel doesnt want to work with OC widget at all but works fine with SetCPU. I've always liked OC widget a little more as it uses less battery than SetCPU.
Great work so far BC your the man. Been running this bad boy and havn't had a single reboot @ 1.5ghz. Though my battery is going quick for some reason, dont know why
This'll work on the stock Sense?
^ Shift Faced
jesusice said:
This'll work on the stock Sense?
^ Shift Faced
Click to expand...
Click to collapse
yes it shall took me a bit but i found out the issue
i'm going to assume this works for stock rooted roms?
d1msum4lyfe said:
i'm going to assume this works for stock rooted roms?
Click to expand...
Click to collapse
Looks like it should, yes
Thank you very much for this. I can confirm that this is running well on stock.
cloverdale said:
Thank you very much for this. I can confirm that this is running well on stock.
Click to expand...
Click to collapse
^ Ditto
Now, coming from the Moment I've never used an OC kernel... anything I should know? Any tips?
^ Shift Faced
jesusice said:
^ Ditto
Now, coming from the Moment I've never used an OC kernel... anything I should know? Any tips?
^ Shift Faced
Click to expand...
Click to collapse
If you get random reboots, it means it's OCed a bit too high; just scale it back a bit and you'll be fine if that ever happens
Is this running at 1.5 all the time or does it throttle between ranges?
What is the default range?
Does the user have to do anything to enable or set the throttling?
zeropants said:
Is this running at 1.5 all the time or does it throttle between ranges?
What is the default range?
Does the user have to do anything to enable or set the throttling?
Click to expand...
Click to collapse
As noted above, I'm new to OC'ing but I'm pretty sure you have to set it to the ranges you want via something like SetCPU or OS Monitor. I believe default is gonna stop at 800mhz unless you scale it up.
EDIT: And thanks Impaler for the help!
^ Shift Faced
zeropants said:
Is this running at 1.5 all the time or does it throttle between ranges?
What is the default range?
Does the user have to do anything to enable or set the throttling?
Click to expand...
Click to collapse
Use SetCPU and select the Mhz/governor you want to use. Each Governor "Throttles differently"
jesusice said:
As noted above, I'm new to OC'ing but I'm pretty sure you have to set it to the ranges you want via something like SetCPU or OS Monitor. I believe default is gonna stop at 800mhz unless you scale it up.
EDIT: And thanks Impaler for the help!
^ Shift Faced
Click to expand...
Click to collapse
No problem, I'm here if you need anything else
What are some good range options?
I'm using 800 min 1.5ghz max interactive. Profiles I have setup: charging 1.5ghz performance, screen off 800 max 245 min
Bumped it up 1.1ghz min 1.5ghz max interactive, going to see how much that affects my battery life
Sent from my PG06100
Dread 7us said:
I'm using 800 min 1.5ghz max interactive. Profiles I have setup: charging 1.5ghz performance, screen off 800 max 245 min
Bumped it up 1.1ghz min 1.5ghz max interactive, going to see how much that affects my battery life
Sent from my PG06100
Click to expand...
Click to collapse
I have mine set to 768 min and 1.4GHz max interactive
Charging is 1.4 performance
screen off 245 min and 800 max interactive.
I don't want to push up around 1.5 until I'm sure this is more stable on my phone.
Dread 7us said:
I'm using 800 min 1.5ghz max interactive. Profiles I have setup: charging 1.5ghz performance, screen off 800 max 245 min
Bumped it up 1.1ghz min 1.5ghz max interactive, going to see how much that affects my battery life
Sent from my PG06100
Click to expand...
Click to collapse
there no real need to have it running at such high freqs all the time mine is set at 245 min 1.31 max usually n got no lag what so ever
the higher speeds are more for gaming and cpu intensive applications
todAY HAS been a good day for HTC EVO SHIFT 4g android development. downloading kernal now! thanks for the hard work
BC you need to set your Donation link up like Impaler. I dont have paypal and it says you have to log in. Impaler's lets you pay with just a credit card. I will send a donation if I can do it without a paypal account.
fifedogg said:
BC you need to set your Donation link up like Impaler. I dont have paypal and it says you have to log in. Impaler's lets you pay with just a credit card. I will send a donation if I can do it without a paypal account.
Click to expand...
Click to collapse
Hey, you clicked my donate link? Thanks!

[Q] How to test if an OC works on the TF?

I loaded the Blades 2 kernel on my TF along side the Revolver ROM.
How can I tell if the OC is safe and working? I am not sure if you stress test it or anything like you do on a Windows PC type device..
acdcking12345 said:
I loaded the Blades 2 kernel on my TF along side the Revolver ROM.
How can I tell if the OC is safe and working? I am not sure if you stress test it or anything like you do on a Windows PC type device..
Click to expand...
Click to collapse
I've found that, in overclocking several Android devices, more often than not if you have an unstable OC, the device will either fail to boot, or will crash constantly. If it's not doing that, you're likely fine.
Um, you're not OCed yet. You need to install setcpu or cpu master and crank up the clock. Clemsyn or Blades gives you the option to OC. It doesn't just OC for you.
lol, and learn from my mistake: when overclocking, don't check the option of "set on boot" untill you have tried overclocking at the Ghz level that you want to use. Believe me, you don't want a bootloop that can only be solved by flashing or restoring from a backup.
acdcking12345 said:
I loaded the Blades 2 kernel on my TF along side the Revolver ROM.
How can I tell if the OC is safe and working? I am not sure if you stress test it or anything like you do on a Windows PC type device..
Click to expand...
Click to collapse
I have done extensive overclocking and undervolting.
Set your OC and voltage settings. Then use setcpu or pimpmycpu min and max to your highest OC MHz.
Then play 1 round of Dungon Defenders. If you make it through that then open the camera.
Repeat this on every MHz from top to bottom. If you are unstable at a frequency then increase your voltage slightly (like 10 - 20 mV) and try again.
If you are stable and want to get a little bit better battery do the same thing but lower the mV until dungeon defenders crashes.
Then start to increase it until you are stable.
If your tablet reboots your way low on mV
If it freezes your low on mV
If the widgets act funny, and/ or disapear every once in awhile your in the right ball park
If everything works except your camera freezes you are very close
Some kernels have more aggressive GPU timings which you can't really change so you might want to try another's kernel if you can't get stable.
Well, it seems that I can't go higher than the 1.2 GHZ. If I go any higher, I get some weird freezes and reboots.
Now I saw the post above but I dont see where I can adjust the different voltages, etc..Maybe I am not using the right program?
acdcking12345 said:
Well, it seems that I can't go higher than the 1.2 GHZ. If I go any higher, I get some weird freezes and reboots.
Now I saw the post above but I dont see where I can adjust the different voltages, etc..Maybe I am not using the right program?
Click to expand...
Click to collapse
What program are you using? Try SetCpu or Pimpmycpu
baseballfanz said:
What program are you using? Try SetCpu or Pimpmycpu
Click to expand...
Click to collapse
SetCPU is what I loaded
acdcking12345 said:
I loaded the Blades 2 kernel on my TF along side the Revolver ROM.
How can I tell if the OC is safe and working? I am not sure if you stress test it or anything like you do on a Windows PC type device..
Click to expand...
Click to collapse
Are you referring to this kernel?
I'm wondering because I have never heard about a "Blades 2" kernel.
EDIT: Nevermind, I figured it out. This is what Revolver Parts calls Blades' 10-01-2011 kernel.
Blades uses some aggressive GPU timings in some of his kernels. You may want to try Clemsyn 22 if you want to try and go above 1.2 GHz.

Undervolting

Does anyone know the ideal settings for undervolting the sensation without causing any problems?
StuartTheFish said:
Does anyone know the ideal settings for undervolting the sensation without causing any problems?
Click to expand...
Click to collapse
Not really. As faux say not all chips are created equal. I've seen up to an amazing -150 but my phone can only handle -50 stable and -75 sometimes with a reboot or two.
Sent from my HTC Sensation 4g using xda premium
Mine handles -100 just fine, but yeah,others can only go -50. Just use system tuner and hit the -12.5 till your phone freezes, then when it restarts go one less and see if it's stable. That's what I did.
Sent from my HTC Sensation 4G using XDA App
I'd also suggest keeping the Max Clock at a consistent value while you play. E.g. UV -100mV might work well at one Mhz then fail at a higher value.
Mine seemed to work consistently at about -100mV, then again I tend to UC unless I'm running CF-Bench or something
Should I only need to concentrate on the lowest and highest clock speeds it's been set to use? Or will I have to undervolt all other frequencies between the two? Not sure if it increments on usage, or simply toggles between the min and max.
If it does increment, how can I test it's stability on the other frequencies if I can't tell what frequency it was using at the time?
Just tapped the -12.5 button a few times, and it reduced all of the sliders. It's -100 now with no apparent issues as of yet.
May I ask the reason for undervolting?
masonic1032 said:
May I ask the reason for undervolting?
Click to expand...
Click to collapse
Mainly to save battery. Altho I have found that it is quite negligible. It may also help with phone heat
masondoctorjt said:
Mine handles -100 just fine, but yeah,others can only go -50. Just use system tuner and hit the -12.5 till your phone freezes, then when it restarts go one less and see if it's stable. That's what I did.
Sent from my HTC Sensation 4G using XDA App
Click to expand...
Click to collapse
I run faux latest version 2.7 beta and I see his scripts to undervolt and the lowest I see it too go is -75 how are you able to go lower to -100.... ???
I think it varies from phone to phone, mine too seems happy enough -100.
StuartTheFish said:
I think it varies from phone to phone, mine too seems happy enough -100.
Click to expand...
Click to collapse
Soooooo how do I undervolt below -75 that's where I am. Now
rawdawgroy said:
Soooooo how do I undervolt below -75 that's where I am. Now
Click to expand...
Click to collapse
If the phone hangs/boots below that level then with the Phone/Kernel/... that's the limit.
I created a GScript script (well a sh script) to U/V after a reboot. I didn't want it to do it automatically as you'd end up in a boot loop. Just hassle to fix. The reason for the GScript was to remove it from the various CPU controllers I'd tried, I ended up just using the CM7 one to control the CPU.
Faux has the command to do it globally (across all frequencies) or individual frequencies. TBH I never bothered with individual ones.
The bottom line is, do what you and your phone are happy with.
EDIT: meant to add you can check the actual value manually. I know the Faux one (same post as the scripts above) but if you are using a different kernel it might be in a different place.

[Q] What Should I adjust Undervolt settings to on SetCPU that are stable

I am using Tsugi 2.3.4 with the Oyasumi 0.1 UV kernal I want to overclock to 1500 but what settings should I undervolt it to that is stable thanks in advance for the info.
DirtyPISTOLA said:
I am using Tsugi 2.3.4 with the Oyasumi 0.1 UV kernal I want to overclock to 1500 but what settings should I undervolt it to that is stable thanks in advance for the info.
Click to expand...
Click to collapse
We can't tell you not all phones are the same, uv a little (10 or 25) run it for a day or two see how it acts, if its steady, uv a little more, when it starts acting up thats your limit go back to previous settings.
NVIDIA NEVER AGAIN!
fcisco13 said:
We can't tell you not all phones are the same, uv a little (10 or 25) run it for a day or two see how it acts, if its steady, uv a little more, when it starts acting up thats your limit go back to previous settings.
NVIDIA NEVER AGAIN!
Click to expand...
Click to collapse
Alright thanks will try
Sent from my LG-P999 using Tapatalk
I've seen some general advice not to UV for anything over 1ghz speeds as well, but it may not hurt to try if you want and adjust as needed for stability.
I'm running on a -75mv at 1.5Ghz faux kernel 0.4.7..
Perfectly stable, benchmarked AnTuTu, Quadrant, and all those other good stuff.
I have not tried -100mv yet, I doubt it will be stable.
Every phone is different, but I run mine at -20 up to 1 G, and -10 for the rest.
Mine I cant undervolt shoot I have to keep my minimum frequency at 500 to be stable, course I can also run at 1.5 all day (I keep it at 1.2).
Well I guess I can't say I cant UV since I use pimp my cpu and it only gives you options in 25 increments, maybe I would be stable at like -10. But coming from my galaxy s 4g where I could UV over -150 and still be stable, that just doesnt even sound worth doing.
Edit: I just thought about it and maybe the reason I cant UV (more) is because I'm using fauxs pre UV/OC kernel, so I dont even know what stock voltage is. But comparing to my sgs4g at stock voltage I am running considerably lower voltages on the g2x.
The faux thread says it's pre uv at -50 across the board.
Beekersguy said:
The faux thread says it's pre uv at -50 across the board.
Click to expand...
Click to collapse
I been running it so long and flashed so many friends phones I can't even remember details anymore!
Sent from my LG-P999 using xda premium

Categories

Resources