Related
THIS GUIDE IS SPECIFICALLY FOR THE MESMERIZE
Steps To Customize Your Mesmerize (For upgrading from any version to FROYO 2.2 EC10)
1.) Upgrade from any setup to 2.2 EC10 (Official Froyo) - If you have not already done so, you will need to upgrade your phone to EC10 2.2. If you have already, skip to the next step. (You can check this in "settings->about phone" under "firmware version" (should be 2.2.1 if you've already done this) NOTE: There is a custom rom listed in this post, I will detail that down below.
NOTE: The roms for this version come pre-rooted, so no need to root. However, if you have issues with superuser permissions (or are staying stock with root), you can use the SuperOneClick Root tool located here
If in the previous step you installed the leak that had the CWM upgrade pre-loaded or you have already manually updated CWM, skip step 2.- You know you have the updated recovery if when you boot to recovery it takes you to the red recovery with voodoo, backup and other options.
2.) Upgrade CWM manually (if needed) downloading this., (this next step by step will upgrade your recovery so that you are able to flash custom rom's/theme's/kernels.)
1.Shut phone off, pull battery out and leave it out.
2.Run odin (assuming you have it installed)
3.Load the cwm-recovery-all.tar file into the PDA spot
4.Plug usb into computer, then into your phone.
5.Hold the volume down key until phone goes into download mode, there will be a yellow android picture.
6.In odin, one of your com: spots should light up yellow - this means your phone is seen by odin (if not you may need drivers)
7.If above step is true, press start and odin will flash the recovery file to your phone. If all goes well the yellow box will turn green and your phone will power off.
8.Now you're able to boot into CWM recovery using the three button method (see glossary here)
3.)Upgrade Kernel With EC10 brought a new turn of events which thanks to jt has allowed fasicnate users to develop kernels which are compatible on the entire line of this model, so be sure to read phidelt's post on kernel's located here and choose one that is compatible with your rom. AOSP and MIUI require a different kernel, so keep this in mind as if you're restoring you may need to flash the appropriate kernel as the restore does not do this for you.
4.) Flash a custom ROM Choose from one of the Custom Rom's that we have out right now;
EC10 Pick and Pack DOWNLOAD HERE -- This is our stock deodexed rom with bloatware moved to a seperate .zip containing flashable packages with those removed apps. - < created by: phidelt82 >
EC10 Custom RomDOWNLOAD HERE - This is a custom rom built by phidelt82 which incorporates some aspects of AOSP into the EC10 rom - launcher and calendar are to name a few.
AOSP -DOWNLOAD HERE - This is a custom ROM/Kernel built with the android open source project code (by lmartin), one of the most "vanilla" rom's meaning no manufacturer's additions such as touchwiz. It's very lean and runs well, but is in BETA stage so beware it may not be for your daily use. NOTE: If you use this rom/kernel and are wanting to return to EC10 you will need to reflash the appropriate kernel for the ROM you are restoring to (for example touchwiz)
MIUI -DOWNLOAD HERE - This is a custom ROM running on the AOSP kernel, you can learn more about it in the thread linked here.NOTE: If you use this rom/kernel and are wanting to return to EC10 you will need to reflash the appropriate kernel for the ROM you are restoring to (for example touchwiz)
GAS EC10 PNP based rom -DOWNLOAD HERE - This is a custom ROM that runs with the touchwiz kernel. Learn more about it in the linked thread.
HEINZ 57 EC10 (PNP/ED01/EC10 based rom) -DOWNLOAD HERE - This is a custom ROM that runs with the touchwiz kernel. Thanks to Sbrissen, it has a lot of extra settings in the TM parts settings menu, allowing you even more customizing. Learn more about it in the linked thread.
5.)Flash a custom THEME Pick one that's compatible with the ROM you are running, from this list.
HELP MY PHONE IS SCREWED (GO TO STOCK 2.2)!!!: If you weren't attentive and made a mistake or haphazardly missed a step and now you're stuck at a boot screen or one of many other failure points, stop what you're doing. Take a deep breath, wu-sa, grus-fraba, whatever you need to do to calm yourself and simply go to this thread and get your phone back to stock. You may not need to go all the way stock, but it seems to be the easiest, and requires the least amount of help from the developers (who have better things to do than answer questions of careless/unlucky people!! - no offense intended) This is also how you would handle getting your phone back to stock before trying to turn it in for repair.NOTE: Being as going to stock means it's expecting your phone to be formatted to RFS instead of EXT4 (lagfix enabled) you should disable lagfix before doing so or you will have errors and md5 mismatches which will disallow you from flashing from recovery. If for some reason you can't access recovery you will just have to disable lagfix manually which is detailed in this thread here.
---------------------------------------------------------------------------------------------------------
==================================================
---------------------------------------------------------------------------------------------------------
THIS IS THE OLD GUIDE FOR CUSTOMIZING 2.1
When I began this process, I had zero experience flashing any sort of software to any sort of devices, and a very minor understanding of "rooting". After much research and crawling I was able to work my way through these steps with little headache, and learned a lot along the way.
Keep in mind there are many variations to each step, this is what worked for me the easiest as a newb.
And last but not least. There is always the disclaimer that attempting any of this can and will make your phone dysfunctional and or possibly bricked beyond repair (but most likely just dysfunctional which is a pain in the arse to deal with) if you do not follow steps completely (and of a trustworthy source such as xda - ehm and in the appropriate forum ).
So make sure you're in a comfortable environment (not a good idea to be trying to accomplish this while slamming beers at the bar), take your time, read each step that these people have taken the time to carefully write up (then follow it), and you'll be just fine. Be patient as things don't always move fast and you never want to freak out as you may screw things up bad, when it's actually just taking longer than you would expect. Always give it at least 5 minutes before you determine it's looping or crashing or whatevering, there is alot going on behind the scenes, trust me!
Steps To Customize Your Stock Mesmerize (For eclair 2.1)
1) Root your phone. - Basically all this means is gaining the ability to give programs/apps and yourself SuperUser access (equivalent of being admin in windows) and also the ability to flash roms via recovery, detailed below.
The easiest way to root is through the z4root.apk. (an application that will run right on your phone)
Download Here
After download, put z4root.apk on your SD card root directory
Then make sure in Settings->Applications that the "Unknown sources" box is checked.
If you don't have a file manager, download a free one from the market, using the file manager navigate to the z4root.apk and select to install it. Note: If you need help at this step, no offense I would suggest getting someone with more experience to help you continue on. I'm serious here
Reboot your phone
After it boots, open the z4root app and press root. At this point it is going to hang, give it 2 minutes and pull the battery. Count to 10, put it back in and turn it on. - This is normal, trust me .
After your phone boots open z4root again and click root, this time it will run no problems and phone will reboot.
NOTE**IF YOU HAVE PROBLEMS WITH z4root: "give Super One Click a try. It's a package you have to download to your computer, but you get to see more of what's actually going on so you know where it's at in the process. I have only used up to version 1.5.5, and I know that version is very capable for the Mesmerize on 2.1. It is located here."-This Information provided by phidelt82**
Once you are rooted (you will see the superuser icon in your apps, it will show apps you've given that permission to... eventually) you will need to make sure you have a file manager that can request root permissions (read/write) before you will be able to complete the next step. Search the market for "root file manager" and pick one to download and install.
Also at this step I would download and install RomManager and TerminalEmulator as you will need these later.
2) Install RomManager and the ClockworkMod Recovery. These will basically just give you the ability to boot into recovery where you can more easily flash kernel's/rom's and anything else you wish to push to your phone. (Recovery is basically a bios like interface - but it's different than the stock version)
I was able to install the Clockwork Mod Recovery very easily just by simply using the root file manager app I had downloaded, along with following with the instructions.
(In your file manager, MAKE SURE YOU ARE Read/Write not Read/Only, for RootExplorer there is a toggle at the top, other ones you may have to enable this through settings, others may just be R/W by default, you will just have to determine this or google the app)
Download the two zip files located in the first post here
Place both files on your SD card root if you were using a computer to download them or you could always download them through your phone's browser
Using the root file explorer app, move the Redbend_ua file from the SD card to /system/xbin/
Long press on the Redbend_ua file and click permissions, there should be one check missing, check that so that all are marked. Save and exit.
Now open TerminalEmulator (Come with me if you want to live )
NOTE:The spaces below are actual spaces and in bml8 there is a lowercase "L" not a "1" there is also a space after cd, after redbend_ua, after restore, and after recovery.bin
TYPE THIS ALL EXACTLY AS SHOWN BETWEEN THE QUOTES
at the command line ($) type "su" (then hit enter)
Type "cd /system/xbin" (then hit enter, which changes directory)
Type "redbend_ua restore /sdcard/recovery.bin /dev/block/bml8" (then hit enter, It will now scroll a bunch of text and reboot.)
After phone boots, open RomManager
Click on Flash ClockworkMod Recovery
Select the Samsung Fascinate your phone will still be the mesmerize. By now - you better damn well trust me , this is just what works with our model
At this point you're all stock and ready for new kernel/rom. (but now you are able to do so very easily)
3) KERNEL: Install Voodoo lagfix kernel and new 5.0 sound
If you want speed and good battery life (and high standard marks) +unlocking the headphone amp and eq controls (it makes even the samsung headset sound killer) go here and follow those steps for using your now functional recovery mode to flash the new Voodoo 5.0 kernel.
You could always install the old Voodoo kernel located here, if for some reason you do not want to take advantage of the new, sound improved one.
Note: Just an FYI, after installing custom kernel's you will always have an issue on start up of seeing a flashing black box in the middle of the samsung logo. This can be corrected by installing a custom boot screen (only requires root access) and you can find out how here.
Note: There are a few ways of getting into this recovery mode, the best way if all else fails is to hold phone from the back with left hand (thumb on volume button, in the middle holding both down and pointer on power button) hold these down until the mesmerize logo pops up then slide your thumb down a bit to volume down only (if you slip don't worry it might blink but it'll still go to recovery) Sometimes this is easier with the back case off. However the best way, is to download and use the QuickBoot app, it allows boot to recovery/reboot/poweroff options from the app.
4) Custom ROM : Download and install the ROM of your choice.
Just pick one from this list Here-They are all there along with other very useful links, read through the first post of each before you decide, some are plug and play some take a few steps first. These are currently only 2.1 eclair builds however right now they have an (somewhat unstable) 2.2 froyo rom/kernel that being worked on but is not quite yet ready for day to day use (some features are not working quite yet). But be patient because these guys will have something long before Samsung let's us have theirs, but who cares - "ours" will be so much better
HELP MY PHONE IS SCREWED!!! (GO TO STOCK 2.1): If you weren't attentive and made a mistake or haphazardly missed a step and now you're stuck at a boot screen or one of many other failure points, stop what you're doing. Take a deep breath, wu-sa, grus-fraba, whatever you need to do to calm yourself and simply go to this thread and get your phone back to stock. You may not need to go all the way stock, but it seems to be the easiest, and requires the least amount of help from the developers (who have better things to do than answer questions of careless/unlucky people!! - no offense intended) This is also how you would handle getting your phone back to stock before trying to turn it in for repair.
MASSIVE AMOUNTS OF Credit go to all of the OP's and many others (some included in my sig), these people are awesome, show them some love! Without them we would be stuck in stock US cell/Samsung HELL!
Final NoteIf you have any suggestions, additions, corrections, subtractions, or multiplications; PLEASE LET ME KNOW! I'm very open to all of the above and since this is now more of a community article let's stick to the android motto and keep it...open source
I gotta say, you did a really good job explaining yourself there. Now I'll just have to send people to one post and not a bunch when I get messages at all hours of the night.
Good work!
phidelt82 said:
I gotta say, you did a really good job explaining yourself there. Now I'll just have to send people to one post and not a bunch when I get messages at all hours of the night.
Good work!
Click to expand...
Click to collapse
Hey thanks, and believe it or not this is the exact reason I decided to put this together with this much detail (aside from answering someone's question). I figure, I'm no android developer but I can follow instruction and explain myself pretty well so I put this together to take some of that off of you guys. (A small token of my appreciation)
Nice work! Stickied for others to follow
Oh and love that comment:
Now open TerminalEmulator (Come with me if you want to live )
Click to expand...
Click to collapse
Gave me a good laugh!
the_scotsman said:
Nice work! Stickied for others to follow
Oh and love that comment:
Gave me a good laugh!
Click to expand...
Click to collapse
Haha well good and thanks, I almost put /badjoke at the end of that comment
EDIT: Edit to main post.
Good Job! This pretty much covers everything. Hopefully soon we can add to it :S
Is there a rough idea of the amount of time it will take to complete? I have pulled the battery a couple of times, and it just sits at the "running exploit in order to obtain root access" spinning the icon for several minutes. I have re-started it for a third time, now just letting it spin to see if it will come around.
LaTuFu said:
Is there a rough idea of the amount of time it will take to complete? I have pulled the battery a couple of times, and it just sits at the "running exploit in order to obtain root access" spinning the icon for several minutes. I have re-started it for a third time, now just letting it spin to see if it will come around.
Click to expand...
Click to collapse
Usually it only takes about a minute or so to complete. If it gives you problems, give Super One Click a try. It's a package you have to download to your computer, but you get to see more of what's actually going on so you know where it's at in the process. I have only used up to version 1.5.5, and I know that version is very capable for the Mesmerize on 2.1. It is located here.
Just wanted to say thanks for all the hard work and for the write ups for those of us new around here. You guys make the scene available for the rest of us.
Sent from my SCH-I500 using Tapatalk
Thanks for the easy walkthrough.
I am getting stuck at the end of step 2. The "redbend_ua restore" part was completed successfully, and after the phone rebooted I launched Rom Manager and clicked "flash ClockworkMod Recovery", selected the Fascinate, and keep getting an error message stating "An error occured while downloading your recovery."
Am I doing something wrong? Is there another way to get clockwork recovery onto my phone? I am on WiFi with a strong signal (I'm about 3 feet from the router) and the connection is working fine in other apps (browser and whatnot) so I don't think it's my internet connection.
Any help for this total newb to the android community would be greatly appreciated.
Mesmerizeuser said:
Thanks for the easy walkthrough.
I am getting stuck at the end of step 2. The "redbend_ua restore" part was completed successfully, and after the phone rebooted I launched Rom Manager and clicked "flash ClockworkMod Recovery", selected the Fascinate, and keep getting an error message stating "An error occured while downloading your recovery."
Am I doing something wrong? Is there another way to get clockwork recovery onto my phone? I am on WiFi with a strong signal (I'm about 3 feet from the router) and the connection is working fine in other apps (browser and whatnot) so I don't think it's my internet connection.
Any help for this total newb to the android community would be greatly appreciated.
Click to expand...
Click to collapse
It's not you. I believe Koush's repo is down right now. Hopefully it will be back up soon and you will be able to finish up.
Thanks for the heads up. Is there any way to get the recovery on the phone without using rom manager, or will I have to wait for the repo's to come back up?
never mind
It's back up. Just flashed to a voodoo kernel. Thanks again for the great instructions.
Very good write up.. You actually made it kind of fun to read if that makes sense.. lol
I seem to be running into problems. Whenever I go into recovery mode my phone doesn't verify the update.zip file. I was wondering how do I fix it or get another one? Also what part does this file play in changing roms?
Error:
Verifying update package...
E:failed to verify whole-file signature
E:signature verification failed
Install aborted
Also very good write up A++ would hack again
Edit: got it working. I had to rerun redbend_ua and make sure it went through a full reboot and didn't stall. I think I wasn't giving it super user permissions. Great writeup thanks again!
thanks this is worked great for me on the Froyo step by step
jmtenny said:
thanks this is worked great for me on the Froyo step by step
Click to expand...
Click to collapse
Great, glad to hear it! This is a new addition and I've just made some more changes and also reformatted the OP so i'ts more obvious that there are two processes.
Thanks so much for taking the time to do this!
I'd like to think that now I have a better understanding of what I'm doing.
I'm having some problems and was wondering if someone could help me please.....
I successfully installed the EA11 leak and updated from 2.1 to 2.2. However, when I boot into the blue recovery and try to hit update.zip from there it just shows me an exlamation icon and never goes into the red recovery instantly like it should according to everyone's directions.
At thiis screen it will stay showing this icon, and the only way off of it is to hit the menu key which takes you back to the blue recovery screen. It then has a description below the blue text that says:
-- Install from package...
Finding update package...
Opening update package...
Verifying update package...
E:Failed to verify whole file signature
E:signature verification failed
Installation aborted.
Am I doing something wrong? Any feedback would be so appreciated.
After bdemartino wrote his AWESOME thread for the Mesmerize it seemed only fitting that the Showcase get their very own... And since his Thread was Flawless, with his permission I'm mostly copy/pasting word for word. as I am copying most of this from elijablake . . . so thanks this thread needs some editing, and I will be working on that in the future . . . . specifically the CWM / ROM manager which will not work. I could use some assistance in rewriting that part. TY!
BEST. ADVICE. EVER. #samsung-mesmerize on irc.freenode.net
<3<3<3<3<3
Also, read the Glossary for definitions and such. I was not the sharpest tool in the shed and it took me a while to find this . . .
Disclaimers
CSOUTH IS RELEASEING 2.2 UPDATE THIS WEEK (6/26). You may just want to wait for that to be released. This thread will be updated when the release occurs as how to flash recovery that you can flash roms with etc.
Keep in mind there are many variations to each step, this is what worked for me the easiest. READ ALOT BEFORE PROCEEDING WITH ANYTHING!!
There is always the disclaimer that attempting any of this can and will make your phone dysfunctional and or possibly bricked beyond repair (but most likely just dysfunctional which is a pain in the arse to deal with) if you do not follow steps completely (and of a trustworthy source such as xda - ehm and in the appropriate forum ).
Steps to get to 2.2 (EB11) on your phone:
**Please note that the links were removed by CSouth for copyright (COPY WRONG *****ES) reasons. So if you can find the files somewhere (ahem . . . ) then you can follow these steps. THIS GUIDE IS PURELY FOR EDUCATIONAL VALUE, I DO NOT ADVOCATE BREAKING COPYRIGHT LAW.
I highly recommend using Heimdall rather than Odin. Don't ask me why . . . maybe because it has a command line utility and it is cross platform. So my instructions will be for using Heimdall.
After you have the downloaded files (from wherever you might have gotten them, you bad bad person) unzip and look for the following files:
-factoryfs.rfs
-modem.bin
-recovery.bin
-zImage
1) Put your phone in download mode by powering down your device, removing the battery, connecting the USB to your computer, and holding the volume down button. It shouldn't take long. You should see a little Android with a shovel.
2) In Heimdall, if using the GUI, put all of the files in their obviously appropriate spots. Don't worry if not everything is filled, just use the files that you have. (You should be using the repartition with the .pit file, the zImage with the Kernel, the recovery, and the modem)
If using the command line utility, cd to the directory where you unzipped the files and
Code:
heimdall flash --repartition --pit atlas_v2.2.1.pit --factoryfs factoryfs.rfs --kernel zImage --modem modem.bin --recovery recovery.bin
Wait for the process to finish, your phone will reboot at the end.
3. That is all, now your phone is updated to 2.2.1. Put the battery back in and boot your new shiny toy!
DO NOT DISCONNECT USB DURING THIS PROCESS AS IT COULD BE POTENTIALLY DISASTROUS!!! DON'T EVEN TOUCH IT AS I HAVE FOUND THE USB CONNECTION TO BE A BIT FLAKY!
Also, it is ok if it takes your phone what seems like forever to boot. This happens whenever you install a new kernel, just be patient.
If you have gotten the most updated batch of files, you should have the proper recovery to begin flashing. If not, well seek help . . . You should have RED RECOVERY!
See here for more information about CWM or go on irc.
To access recovery, you can use the three finger method. (Hold down the volume up and down keys and the power button all at the same time when you're turning your phone on) Once you see the Samsung splash screen you can remove your finger from the power button, but keep holding down both volume keys.
You should then go here to check out themes and mods.
Steps For Rooting either 2.1 or 2.2.1
Basically all this means is gaining the ability to give programs/apps and yourself SuperUser access (equivalent of being admin in windows) and also the ability to flash roms via recovery, detailed below.
**NOTE: most custom roms come rooted, so if you are installing a custom rom in 2.2.1, you most likely don't have to go through these steps. Just flash to the ROM you want . . . ***
The easiest way to root is through the z4root.apk. (an application that will run right on your phone)
Download Here
After download, put z4root.apk on your SD card root directory
Then make sure in Settings->Applications that the "Unknown sources" box is checked.
If you don't have a file manager, download a free one from the market, using the file manager navigate to the z4root.apk and select to install it. Note: If you need help at this step, no offense I would suggest getting someone with more experience to help you continue on. I'm serious here
Reboot your phone
After it boots, open the z4root app and press root. At this point it is going to hang, give it 2 minutes and pull the battery. Count to 10, put it back in and turn it on. - This is normal
After your phone boots open z4root again and click root, this time it will run no problems and phone will reboot.
NOTE**IF YOU HAVE PROBLEMS WITH z4root: "give Super One Click a try. It's a package you have to download to your computer, but you get to see more of what's actually going on so you know where it's at in the process. I have only used up to version 1.5.5, and I know that version is very capable for the Showcase. It is located here."-This Information provided by phidelt82**
Once you are rooted (you will see the superuser icon in your apps, it will show apps you've given that permission to... eventually) you will need to make sure you have a file manager that can request root permissions (read/write) before you will be able to complete the next step. Search the market for "root file manager" and pick one to download and install.
I use Root Explorer
It's a few bucks, but there's hardly a day that goes by when I don't use it.. (Well worth the money)
THE ECLAIR SECTION IS REMOVED AS CSOUTH IS RELEASING UPDATE THIS WEEK (6/27)
Hehmmmm....
nice write-up!
Upgraded the Showcase to 2.2.1 build EE25 with Samsung Kies this morning. Also had no issue rooting with superoneclick.
cpflow said:
Upgraded the Showcase to 2.2.1 build EE25 with Samsung Kies this morning. Also had no issue rooting with superoneclick.
Click to expand...
Click to collapse
Kies has 2.3 out now =)
Kies Mini have 2.3.5 out now for generic cdma showcase.
Sent from my SCH-I500 using Tapatalk
*Edit*
It seem everyone forgot about the Samsung Showcase Galaxy S Generic CDMA.
I managed to Root it flash CWMR and flash TSM TW 4.0 ROM. but then try to go back to stock and lost 3G. So I returned it and get a new one. No more mods for me I'm done no one cares about Generic CDMA.
Can someone provide directions to install a custom rom for a Showcase running stock 2.3.4? I don't have root. I'd really appreciate any help!
Hi, I'm relatively new to the Desire S. Iv just purchase the XTC pay as you go clip from
http://www.fonefunshop.co.uk/cable_picker/96007_XTC_Clip_PAYG_(Pay_As_You_Go_-_Red_XTC_Clip).html
It's seems quite straight forward to operate, but I need some clarification (iv searched threads but couldn't find answer)
After iv s-off'd with the clip, will the stock ROM be erased, I.e , will I need to install a new ROM for the phone to work? Will I also need to I install a new radio? if so, what's the best order to do this.... Flash radio first, then ROM, or ROM and then radio, or it dosnt matter?
I guess, just to clarify, I'd like to know what steps I need to take once iv s off'd with the clip to get a working phone. Also, before I use the clip, are there any steps/precautions I should take.
Many thanks in advance.
The XTC Clip will factory reset your phone so make sure you backup what you can.
Then do the following:
1. Make sure USB debugging is enabled (settings -> applications -> development)
2. Make sure you have an SD card (formatted and inserted.) (Existing card is fine)
3. Get the APK on the phone, and install it. You could Go to market and download es file explorer its free. Then download the apk from the post and save it on your laptop/pc. Connect usb cable to phone and select mount sd card, copy apk to sdcard. Unmount sdcard from laptop/pc on phone. Using ES file explorer browse to apk and select it, it will give you option to install. Install it. Done.
4. Open the APK, press the root button i.e Go into app drawer and select gingerbreak, choose root. It will say after its done something like "not sure whats happened reboot to see if you have superuser..."
Reboot and your rooted.
5. Within your rooted ROM go to market and download ROM Manager, Install and Run. Answer yes to the Superuser prompt. Choose option to install recovery.
6. Then, download any custom rom of your choice from here (XDA) and copy to your SD Card (using above method).
7. Reboot into recovery either by using the "Reboot into Recovery" option in ROM Manager or by shutting down your phone and whilst holding vol down press the power button and then select recovery within bootloader.
8. Finally navigate to your custom rom in recovery by selecting the "Install Zip from SDCard" Option, once installed, reboot.
You could also download the latest recovery from here, id recommend the EXT4 recovery which you can install by using the above method, i.e download and copy to sdcard, reboot to recovery and install zip.
Hope this helps
Thank you so much for taking the time to reply Marylandcookie. Just want to clarify, after iv s-off'd, even though the phone will be factory reset, I should still be able to use the phone (in other words the stock ROM will still be on the phone and not erased, or do I have to install the stock ROM again.). Also, which APK do you refer to?
Last question, when I do get into installing custom ROMs after iv s-off'd and rooted, if I need to install a recommended radio for the ROM, is it best to flash the ROM first and then the radio, or the radio first and then the ROM.
I also noticed in the development section that there's a new HBOOT version. Is it essential I install this?
Thanks again for your earlier reply, much appreciated.
Hi nbhadusia, yes you will still be able you phone with out doing anything more.
and the apk i question is this attached below,as for the recomend radio i tend to look in the devs sig to see which one they are using,and i have found flashing the radio after flashing the rom is fine, but i think it do'snt really matter. hope this helps
Thanks for clarifying and providing the link, very much appreciated.
Hi guys, this is the first post i upload and want to take the occasion to greet you all.
In these days i bought a Samsung Infuse 4G...i really like this phone but want to be able to use it with some special features such as connecting various USB devices to the phone and other juicy stuff.
I read that the builtin ROM is not capable of such this thing, and Ice Cream Sandwitch, witch should allow to do that, is not available for this smartphone model. At least not officially.
My choice fell upon CM7 LinuxBozo ROM ( http://forum.xda-developers.com/showthread.php?t=1311960 ).
I rooted my device. I'm sure of that because i am able to use the root explorer with root privileges and the root menu shows up among my applications.
I then followed the instructions here ( http://forum.xda-developers.com/showthread.php?t=1107881 ) in order to install the ClockWorkMod Flashing Menu but I am not sure whether anything went allright or not as, after trying both the methods shown on the guide, nothing happened (in the first case, the automatic install through ROM Manager seems to work, a message appears on the screen confirming anything went smooth but when i reboot i see the normal reboot menu, no advanced menu nor CWM menu; in the second case i tried to manually load the CWM menu by placing the update file in the SD and renaming it to update.zip, the update gets stuck somewhere saying something about a bad or wrong signature, tried it a few times and with different CWM update versions but nothing to do).
I then stumbled into a workaround to fix that issue by an even more manual procedure ( http://www.youtube.com/watch?v=PkMo8rBehHg&feature=related ) basically consisting in copying the "recovery" executable from the CWM update archive to the directory /system/bin and of course chmodding it to rwxr-xr-x and chowning it to the root.
Now the CWM screen appears but, as i attempt to flash the CM7 ROM, the flashing gets stuck at "Finding update package". I read here ( http://forum.xda-developers.com/showthread.php?t=821499 ) that it could happen sometimes and it's just a matter of trying and trying again... I tried at least ten times up to now but it keeps getting stuck...maybe it's not my case.
Hope someone will help me out...i really need that USB reading feature. Thank you.
baareem said:
Hi guys, this is the first post i upload and want to take the occasion to greet you all.
In these days i bought a Samsung Infuse 4G...i really like this phone but want to be able to use it with some special features such as connecting various USB devices to the phone and other juicy stuff.
I read that the builtin ROM is not capable of such this thing, and Ice Cream Sandwitch, witch should allow to do that, is not available for this smartphone model. At least not officially.
My choice fell upon CM7 LinuxBozo ROM ( http://forum.xda-developers.com/showthread.php?t=1311960 ).
I rooted my device. I'm sure of that because i am able to use the root explorer with root privileges and the root menu shows up among my applications.
I then followed the instructions here ( http://forum.xda-developers.com/showthread.php?t=1107881 ) in order to install the ClockWorkMod Flashing Menu but I am not sure whether anything went allright or not as, after trying both the methods shown on the guide, nothing happened (in the first case, the automatic install through ROM Manager seems to work, a message appears on the screen confirming anything went smooth but when i reboot i see the normal reboot menu, no advanced menu nor CWM menu; in the second case i tried to manually load the CWM menu by placing the update file in the SD and renaming it to update.zip, the update gets stuck somewhere saying something about a bad or wrong signature, tried it a few times and with different CWM update versions but nothing to do).
I then stumbled into a workaround to fix that issue by an even more manual procedure ( http://www.youtube.com/watch?v=PkMo8rBehHg&feature=related ) basically consisting in copying the "recovery" executable from the CWM update archive to the directory /system/bin and of course chmodding it to rwxr-xr-x and chowning it to the root.
Now the CWM screen appears but, as i attempt to flash the CM7 ROM, the flashing gets stuck at "Finding update package". I read here ( http://forum.xda-developers.com/showthread.php?t=821499 ) that it could happen sometimes and it's just a matter of trying and trying again... I tried at least ten times up to now but it keeps getting stuck...maybe it's not my case.
Hope someone will help me out...i really need that USB reading feature. Thank you.
Click to expand...
Click to collapse
what color is your cwm screen?
this may be a simpler way of gettin cwm:
http://forum.xda-developers.com/showthread.php?t=1220090
specifically, the CWM instructions set.
I see that the instructions you suggested me would mean to start the process almost from scratch. I will do that as soon as i finish studying the nazis for my school report .
And maybe after getting the next answer from you
The boot screen is green text on black backgroud.
Holding audio and power buttons for 10 seconds doesn't prompt me to the red boot screen if it was what you meant and if I read the instructions provided well (witch i didn't as i have no time now)... don't get me wrong. Just trying to provide you as more information as possible.
baareem said:
I see that the instructions you suggested me would mean to start the process almost from scratch. I will do that as soon as i finish studying the nazis for my school report .
And maybe after getting the next answer from you
The boot screen is green text on black backgroud.
Holding audio and power buttons for 10 seconds doesn't prompt me to the red boot screen if it was what you meant and if I read the instructions provided well (witch i didn't as i have no time now)... don't get me wrong. Just trying to provide you as more information as possible.
Click to expand...
Click to collapse
if you still have root, download from market
sgs kernel flasher and the flash the gingerbread kernel to give you RED recovery and flash the rom of your choice after a factory reset and usual wipes
Cool... i'm now running CM7 !
Here is what i missed for anyone who would have the same problem in the future (you can find the download links here: http://forum.xda-developers.com/showthread.php?t=1220090 ):
CWM Installation Instructions:
1) You must be rooted.
2) If you have a /Voodoo folder on your internal SD card, delete it and reboot.
3) If you're already running a custom ROM with Voodoo lagfix FULLY enabled, you can skip to step 7.
4) Download CWM-community-kernel-v8.zip if you're on Froyo or CWM-infused-v2.0.1-kernel.zip if you're on Gingerbread and place it on your internal SD card.
5) Install SGS Kernel Flasher from the Market.
6) Open SGS Kernel Flasher, select choose kernel, select the file you downloaded, and select flash kernel. Your phone will reboot and begin to enable Voodoo lagfix. Let it do that and boot all the way up. It will take a while (5-10 minutes) because it's converting all partitions to ext4.
7) Download update-infused-v2.X.X-full.zip and place it on your internal SD card.
8) Power off your phone.
9) With the phone powered off, hold both volume keys and the power button for about 10 seconds and then release. This should boot you into RED CWM.
10) Select "install zip from sdcard" and select update-infused-v2.X.X-full.zip.
11) Once that finishes, select "wipe data/factory reset".
12) Select "reboot system now".
13) Do NOT restore system data with Titanium Backup. Do NOT restore ALL apps with data. If you absolutely must restore something with Titanium Backup, only restore MISSING apps with data.
Click to expand...
Click to collapse
Now just another question: i noticed different errors when running the market and other old built-in apps... I just need to reinstall gapps right?
yeah, that is why it's stickeyed.
you just had to read/search them.
market wise, there's a market fix
or you can also factory reset and wipe cache and dalvik in cwm
Thanks. You helped me solving this and now anything works fine. Have a good day.
Thread (NOT) SOLVED.
--------
(Edited after realizing gapps still don't show up as installation didn't really worked)
baareem said:
Thanks. You helped me solving this and now anything works fine. Have a good day.
Thread SOLVED.
Click to expand...
Click to collapse
np. take it easy, bro.
I was too quick saying it worked.
The Infuse just booted up but nothing changed. I then tried to do the zip installing through rom manager again but invane.
When trying with the manual install it promts me with this error:
E: Can't open /emmc/gapps-gb-xxxxxxx-signed.zip
(bad)
Installation aborted.
Click to expand...
Click to collapse
I tried different versions of gapps including the one suggested in the CM wiki but with no luck. I guess the problem is somewhere else.
PS: now i see the blue on black bootscreen as in order to install gapps with rom manager i was asked to reinstall CWM trough it...
baareem said:
I was too quick saying it worked.
The Infuse just booted up but nothing changed. I then tried to do the zip installing through rom manager again but invane.
When trying with the manual install it promts me with this error:
I tried different versions of gapps including the one suggested in the CM wiki but with no luck. I guess the problem is somewhere else.
PS: now i see the blue on black bootscreen as in order to install gapps with rom manager i was asked to reinstall CWM trough it...
Click to expand...
Click to collapse
what version of ROM were you running when you tried this?
Stock FRoyo?
Cyanogenmod 7 ... exactly this version : http://forum.xda-developers.com/showthread.php?t=1311960
Kernel version is 2.6.35.7 , android v 2.3.7.
The old, OOB version i had was froyo 2.2.6 if i well remember.
baareem said:
Cyanogenmod 7 ... exactly this version : http://forum.xda-developers.com/showthread.php?t=1311960
Kernel version is 2.6.35.7 , android v 2.3.7.
The old, OOB version i had was froyo 2.2.6 if i well remember.
Click to expand...
Click to collapse
I haven't played with CM7, it's not an infuse based rom.
I recall some installation issues with it.
I remember an unsuccess reboot intially and pull battery thing..not sure.
If you're looking to install another rom, odin back to stock and start over.
check out my sig line for some useful links
I rooted my device and tried to install a custom ROM. But something got messed up and I had to unrooted the device and restore it to factory version with an RUU given by Hack Ace.
After restoring the device, Market doesn't upgrade to Google Play. I tired to restart and it did not help.
I'm now running GingerBread 2.3.3 with a HTC Sesse 2.1
Can anyone help me with what is wrong?
Try logging out of google if you haven't or look for the google play apk file and install it should be one floating around here somewhere
Well just read through and see if this helps
http://forum.xda-developers.com/showthread.php?p=24416330
Or go into settings apps then look for you market app clear data cache if u can and try going back onto your market and see if that helps
My Inspire
i was able to install Play Store by downloading the Vending app from Media fire.
Thanks for the Link though.....it has lot of useful information in it.
kandalaphani said:
i was able to install Play Store by downloading the Vending app from Media fire.
Thanks for the Link though.....it has lot of useful information in it.
Click to expand...
Click to collapse
Awesome.. ? for you why did you go back to stock or are you planning to root again?
when i tried to flash the new ROM from ROM Manager...it left my Phone in a wierd state and i was not able to access Gmail or Play Store.
This is the first time i tried to root and Flash a new ROM and i am not exactly sure about the recovery process. So i decided to RESET everything. I am now looking into more videos and articles and videos to get familiar with the process. I would certainly try rooting again ASAP.
kandalaphani said:
when i tried to flash the new ROM from ROM Manager...it left my Phone in a wierd state and i was not able to access Gmail or Play Store.
This is the first time i tried to root and Flash a new ROM and i am not exactly sure about the recovery process. So i decided to RESET everything. I am now looking into more videos and articles and videos to get familiar with the process. I would certainly try rooting again ASAP.
Click to expand...
Click to collapse
Well I never used the Rom manager aka clock work mod to flash a rom. Alway down load it and drag n drop to the sd card and boot into recovery mode and flash but you have to have cwm first and flash it to the recovery mode which there fore allow you too boot up into recovery with out issues.
Well once you do root again look me up. I can help with some basic info if I get time I can post or message you with some steps that I do that could help you out.
My Inspire
CYRAXDroid said:
Well I never used the Rom manager aka clock work mod to flash a rom. Alway down load it and drag n drop to the sd card and boot into recovery mode and flash but you have to have cwm first and flash it to the recovery mode which there fore allow you too boot up into recovery with out issues.
Well once you do root again look me up. I can help with some basic info if I get time I can post or message you with some steps that I do that could help you out.
My Inspire
Click to expand...
Click to collapse
Sure...Thanks for your time..
kandalaphani said:
Sure...Thanks for your time..
Click to expand...
Click to collapse
Hey no worries.. once you flash roms and get into kernels scripts etc its not all that bad
My Inspire
So this is an idea of what I do when I flash a rom and some other ideas/tips.
Getting Started or Flashing A Rom:
Once you root your phone (this is not in any order really) you should get ROM Manager aka Clock Work Mod. Once you get that, open the CWM and the first top half you will see flash clockworkmod recovery make sure your on wifi I would at least for the updates. You will see a dialog box click desire hd. This will allow you to make back ups of your settings that you made when you flash a rom its always a good idea to make your backups its a life save!! So, once you made your back up and this is what I do.. I plug in my phone to the pc switch to disk mode which will let you see whats on your sd card. Since you flash the CWM and recovery you will see on your sd card a folder called clockworkmod open then backups folder you will see you back that you made, drag and drop that backup file that you made to your fold that you made on pc to save it for later. And thats pretty much how I save my backups of roms etc.. Now if you need to load that back up just plug phone in disk mode cwm fold>backup drag and drop back up that you need. And boot into recovery mode and select back up and restore and select restore and the file boot and your good..
I would download which Rom I would like to use. Save it to pc to a folder that I have made that I store all my roms, backups,radios & rils, kernels..etc.. just to keep myself organized. Once you get your rom just drag and drop it to the ROOT of the sd card do NOT add it in any folder thats on the sd card. Once you have it on the card just boot into recovery flash your rom.. Other then that its easy to flash the rom.. And when you get all your settings set up make a back up and when done save it to the pc and delete it from the sd card if you dont want to keep on the card I do that..
When it comes to battery life it depends on what the rom.. But I like to use killers http://forum.xda-developers.com/showthread.php?t=1305228&highlight=killersolth scripts for the kernels.. For me I always flash a different kernel upon flashing a new rom. For me having the kernel and killers script is the best combo for me to have for performance and battery life.. now since I have inspire I use the uv lites scripts.
For the most part flashing radios & Rils you would never really need to do that so I wouldnt recommend it for now maybe later but read about it its good to know what it does..
Other sides which I for got to add.. When you flash a new rom its always good to wipe user data.,cache, delvik it makes it for a good clean install with other roms..
Also the desire HD thread which the inspire can use the roms from that thread to.
Well I hope this helps you in any way.. if you need help PM me best of luck