I have a Dolphin 9900 handset which runs WM 6.1. Each day at 12:00PM and 12:00AM the device turns on automatically. There are no e-mail accounts setup on this device. I have tried to disable Direct Push, assuming that's the reason for its issue, but nothing has worked. I have tried the following:
[HKEY_CURRENT_USER\ControlPanel\Notifications\Remin ders\AutoSnooze]
"AutoSnoozeMins"=dword:0
HKCU\ControlPanel\Notifications\{A877D65A239C-47a7-9304-0D347F580408}
set value "Options" to 20000000 (hexadecimal) or 536870912 (decimal)
And the steps found here:
The Exchange Security Policy (4131) updates the device policy:
HKLM\Security\Policies\00001023: 0 = Enabled; 1 = Disabled
To change the inactivity timer:
HKLM\Comm\Security\Policy\LASSD\AE\{50C13377-C66D-400C-889E-C316FC4AB374}\
AEFrequencyType: 0 = No inactivity time; 1 = Activity time enable
AEFrequencyValue: = number of minutes before timeout
To change the password strength policy:
HKLM\Comm\Security\Policy\LASSD\LAP\lap_pw\
MinimumPasswordLength: minimum number of characters in password (0 defaults to 1)
PasswordComplexity: 0 = Require Alphanumeric; 1 = Require numeric (PIN); 2 = No restriction
And finally to change the Device wipe settings:
HKLM\Comm\Security\Policy\LASSD\
DeviceWipeThreshold: -1 = disabled; (any positive number) = # failed attempts before device memory gets whacked
CodewordFrequency: # of attempts before a codeword is displayed to prevent accidental device wipe.
None of these steps worked as the device still turns on at 12:00 each time. Does anyone have any suggestions?
Hopefully these will be useful if someone messed up theirs. Eventually after I update/root I will post any changes.
stock unrooted evo 4g
hardware 0003
baseband = 1.39.00.05.31
software = 1.32.651.6
pri = 1.40_003
prl = 60668
Code:
##data# > wimax settings
standby time (minute) = 10
scan rate (minute) = 30
NAI = [email protected]
username = [email protected]
realm = sprintpcs.com
spi mn-aaa = 4D2
spi mn HA = 4D2
home ip address = 0.0.0.0
second home agent = 68.28.89.76
center frequency = 2647000,2657000,2667000
bandwidth = 10, 10, 10
napdis = 000002
nspdis = 000004
wimax scan attempt timeout(s) = 1
wimax scan retry(s) = 900
wimax idle sleep(s) = 10
wimax entry rx (rssi) (dbm) = -89
wimax entry cinr (db) = 4
wimax entry delay(s) = 600
wimax exit cinr (db) = 2
wimax exit delay(s) = 2
handoff threshold = 0
idle mode timer = 0
tls = enable
ttls = disable
obviously replace the 4g mac and username with your own.
--------------------------------------------
edit: after OTA update, some missing and modified settings
stock unrooted evo 4g
hardware 0003
baseband = 2.05.00.06.10
software = 1.47.651.6
pri = 1.40_003
prl = 60668
Code:
##data# > wimax settings
standby time (minute) = 10
scan rate (minute) = 30
NAI = [email protected]
username = [email protected]
realm = sprintpcs.com
[STRIKE]spi mn-aaa = 4D2
spi mn HA = 4D2
home ip address = 0.0.0.0
second home agent = 68.28.89.76[/STRIKE]
center frequency = 2647000,2657000,2667000
bandwidth = 10, 10, 10
napdis = 000002
nspdis = 000004
wimax scan attempt timeout(s) = 1
[COLOR="SeaGreen"]wimax scan retry(s) = 300[/COLOR]
wimax idle sleep(s) = 10
wimax entry rx (rssi) (dbm) = -89
wimax entry cinr (db) = 4
[COLOR="SeaGreen"]wimax entry delay(s) = 300[/COLOR]
wimax exit cinr (db) = 2
wimax exit delay(s) = 2
handoff threshold = 0
idle mode timer = 0
tls = enable
ttls = disable
edit 2: added additional settings per request
------------------------------------
Code:
data profile
active profile = 1
username = [email protected]
spi mn-ha = 4d2
spi mn-aaa = 4d2
reverse tunnel preferred = enable
home ip address = 0.0.0.0
primary home agent = 255.255.255.255
second home agent = 68.28.89.76
dsa server url = https://dsa.spcsdns.net:443/dsa/
Code:
evdo
ddtm = disable
preferred mode = automatic
Code:
advanced
meid(hex) = your meid
p_rev = IS-2000 (6)
scm = 58
slot mode = enable
slot cycle index = 2
mcc (mobile country code) = 310
mnc (mobile network code) = 00
msid = (not sure if this is private so not posting)
accolc (access overload class) = 2
vocoder = enable
evrc-b = disable
home orig = evrc
roam orig = voice 13k
home sys registration = enable
foreign sid registration = enable
foreign nid registration = enable
mn ha spi set = enable
mn aaa spi set = enable
home side/nid #1 = 4139/65535
mms server url = http://mms.sprintpcs.com
rtsp proxy port = 554
rtsp proxy address = rtsp.vog.sprintpcs.com
http pd proxy port = 8085
http pd proxy address = pd.vog.sprintpcs.com
======================================
after froyo ota update
android version = 2.2
baseband = 2.15.00.07.28
kernel = 2.6.32.15-g746f4f0 [email protected] #58
build = 3.26.651.6 cl218634 release-keys
software = 3.26.651.6
browser = webkit3.1
pri = 1.40_003
prl = 60668
Code:
##data#
standby time (minutes) = 10
scan rate (minutes) = 30
NAI = [email protected]
user name = [email protected]
realm = sprintpcs.com
center frequency = 2647000,2657000,2667000
bandwidth = 10,10,10
napdis = 000002
nspdis = 000004
wimax_scan_attempt_timeout(s) = 1
[COLOR="Lime"]wimax_scan_retrys = 120[/COLOR]
wimax_idle_sleep(s) = 10
wimax_entry_rx(rssi)dbm = -89
wimax_entry_cinr(db) = 4
wimax_entry_delay(s) = 300
wimax_exit_cinr (db) = 2
wimax_exit_delay(s) = 2
handoff threshold = 0
idle mode timer = 0
tls = enable
ttls = disable
Awesome thanks!
Swyped from my EVO via XDA app
When you root your PRI will roll back to 1.34
There is quite a few obvious entries that are missing on a rooted evo with 4g working.
Hmm
Interesting
James
added wimax data settings after applying OTA update
Thanks for this, it was a big help!
I had screwed with some settings and ended up not remembering what they were
Can some post the screen shots/info for the other settings under data plz, looking for default unmodified ones.
I thought these were the default unmodified settings?
~Jasecloud4
jasecloud4 said:
I thought these were the default unmodified settings?
~Jasecloud4
Click to expand...
Click to collapse
they prob are but i need the ones for evdo
stress1ner said:
Can some post the screen shots/info for the other settings under data plz, looking for default unmodified ones.
Click to expand...
Click to collapse
added info to first post
TeknoJnky said:
added info to first post
Click to expand...
Click to collapse
Good move not posting your MSID, it's private
my 4g isnt working after the simple root process. how might i go about figuring out why?
jbcain said:
my 4g isnt working after the simple root process. how might i go about figuring out why?
Click to expand...
Click to collapse
I would recommend flashing whitslacks rooted oem to make sure all the radios and such are up to date.
http://forum.xda-developers.com/showthread.php?t=715915
Once its all working from there, then you can try out other roms if you desire.
TeknoJnky said:
added info to first post
Click to expand...
Click to collapse
good looking out.
TeknoJnky said:
Code:
##data# > wimax settings
standby time (minute) = 10
scan rate (minute) = 30
NAI = [email protected]
username = [email protected]
realm = sprintpcs.com
[STRIKE]spi mn-aaa = 4D2
spi mn HA = 4D2
home ip address = 0.0.0.0
second home agent = 68.28.89.76[/STRIKE]
center frequency = 2647000,2657000,2667000
bandwidth = 10, 10, 10
napdis = 000002
nspdis = 000004
wimax scan attempt timeouts = 1
[COLOR="SeaGreen"]wimax scan retrys = 300[/COLOR]
wimax idle sleeps = 10
wimax entry rx (rssi) (dbm) = -89
wimax entry cinr (db) = 4
[COLOR="SeaGreen"]wimax entry delays = 300[/COLOR]
wimax exit cinr (db) = 2
wimax exist delays = 2
handoff threshold = 0
idle mode timer = 0
tls = enable
ttls = disable
Click to expand...
Click to collapse
Just FYI: If you change the WIMAX_scan_attempt_Timeout - the only valid entries are 5-300, so you won't be able to restore the default value of "1"
updated with froyo OTA defaults
only change noticed was
wimax_scan_retrys = 120 (from 300)
...and the update resets all values that were manually changed.
Question: How would the MN HA SPI Set and MN AAA SPI Set values be changed from Enable (stock) to Disable? I was checking speed downloads tonight on my Evo and my wife's and noticed are settings are different, but I didn't change my values manually something else did... All other settings are consistent.
Both phones are rooted and running MikFroyo 4.5.
I tried to google what those settings are even for, but didn't have much luck. Any help would be appreciated.
Question: What are the MN HA SPI Set and MN AAA SPI Set values for?
I was comparing download speeds on my wife's Evo and mine tonight after the latest PRL update and noticed our settings are different.
Her phone shows both values as Enable and mine show Disable. I have no idea how mine got changed.
I tried to google search but didn't find anything helpful. Any help would be appreciated.
Edit: Both of our phones are rooted and currently running MikFroyo 4.5.
Is there a way to disable 4G? My 4G keeps turning itself on and I *DONT* want it on EVER AGAIN.
SOLVED: Chaged 4G MAC to 00:00:00:00:00:00 and now it doesn't connect and after a few attemps it idles. Still haven't checked how much the battery drains... Another solution is to change the RSA key just 1 character will make it not connect. (both the MAC & RSA keys can be edited in wimax.img)
I tired finding a thread to my second question but was unsuccessful again so here it is.
Does anyone know the galaxy S 4G Service Codes??? Thanks!
[email protected] said:
I tired finding a thread to my second question but was unsuccessful again so here it is.
Does anyone know the galaxy S 4G Service Codes??? Thanks!
Click to expand...
Click to collapse
~Samsung Mobile Global Codes~
*#1234# = Firmware Version.
*#2222# = H/W Version.
*#8999*8376263# = All Versions Together.
*#8999*8378# = Test Menu.
*#4777*8665# = GPSR Tool.
*#8999*523# = LCD Brightness.
*#8999*377# = Error Menu.
*#8999*327# = EEP Menu.
*#8999*667# = Debug Mode.
*#92782# = PhoneModel. (Wap)
#*5737425# = JAVA Mode.
*#2255# = Call List.
*#232337# = Bluetooth MAC Adress.
*#5282837# = Java Version.
#*4773# = Incremental Redundancy.
#*7752# = 8 PSK uplink capability bit.
#*7785# = Reset wakeup & RTK timer cariables/variables.
#*7200# = Tone Generator Mute.
#*3888# = BLUETOOTH Test mode.
#*7828# = Task screen.
#*#8377466# = S/W Version & H/W Version.
#*2562# = Restarts Phone.
#*2565# = No Blocking? General Defense.
#*3353# = General Defense, Code Erased.
#*3837# = Phone Hangs on White screen.
#*3849# = Restarts Phone.
#*3851# = Restarts Phone.
#*3876# = Restarts Phone.
#*7222# = Operation Typ: (Class C GSM)
#*7224# = !!! ERROR !!!
#*7252# = Operation Typ: (Class B GPRS)
#*7271# = CMD: (Not Available)
#*7274# = CMD: (Not Available)
#*7337# = Restarts Phone. (Resets Wap Settings)
#*2787# = CRTP ON/OFF.
#*2886# = AutoAnswer ON/OFF.
#*3737# = L1 AFC.
#*5133# = L1 HO Data.
#*7288# = GPRS Detached/Attached.
#*7287# = GPRS Attached.
#*7666# = White Screen.
#*7693# = Sleep Deactivate/Activate.
#*7284# = L1 HO Data.
#*2256# = Calibration info? (For CMD set DEBUGAUTONOMY in cihard.opt)
#*2286# = Databattery.
#*2527# = GPRS switching set to (Class 4, 8, 9, 10)
#*2679# = Copycat feature Activa/Deactivate.
#*3940# = External looptest 9600 bps.
#*4263# = Handsfree mode Activate/Deactivate.
#*4700# = Please use function 2637.
#*7352# = BVMC Reg value (LOW_SWTOFF, NOMINAL_SWTOFF)
#*2558# = Time ON.
#*3370# = Same as 4700.
#*3941# = External looptest 115200 bps
#*5176# = L1 Sleep.
#*7462# = SIM Phase.
#*7983# = Voltage/Freq.
#*7986# = Voltage.
#*8466# = Old Time.
#*2255# = Call Failed.
#*5187# = L1C2G trace Activate/Deactivate.
#*5376# = DELETE ALL SMS!!!!.
#*6837# = Official Software Version: (0003000016000702)
#*7524# = KCGPRS: (FF FF FF FF FF FF FF FF 07)
#*7562# = LOCI GPRS: (FF FF FF FF FF FF FF FF FF FF FF FE FF 01)
#*2337# = Permanent Registration Beep.
#*2474# = Charging Duration.
#*2834# = Audio Path. (Handsfree)
#*3270# = DCS Support Activate/Deactivate.
#*3282# = Data Activate/Deactivate.
#*3476# = EGSM Activate/Deactivate.
#*3676# = FORMAT FLASH VOLUME!!!
#*4760# = GSM Activate/Deactivate.
#*4864# = White Screen.
#*5171# = L1P1.
#*5172# = L1P2.
#*5173# = L1P3.
#*7326# = Accessory.
#*7683# = Sleep variable.
#*8465# = Time in L1.
#*2252# = Current CAL.
#*2836# = AVDDSS Management Activate/Deactivate.
#*3877# = Dump of SPY trace.
#*7728# = RSAV.
#*2677# = Same as 4700.
#*3728# = Time 2 Decod.
#*3725# = B4 last off.
#*7372# = Resetting the time to DPB variables.
#*7732# = Packet flow context bit Activate/Deactivate.
#*6833# = New uplink establishment Activate/Deactivate.
#*3273# = EGPRS multislot. (Class 4, 8, 9, 10)
#*7722# = RLC bitmap compression Activate/Deactivate.
#*2351# = Blinks 1347E201 in RED.
#*4472# = Hysteresis of serving cell: 3 dB
#*2775# = Switch to 2 inner speaker.
#*9270# = Force WBS.
#*7878# = FirstStartup. (0=NO, 1=YES)
#*3757# = DSL UART speed set to. (LOW, HIGH)
#*8726# = Switches USBACM to Normal.
#*8724# = Switches USBACM to Generator mode.
#*8727# = Switches USBACM to Slink mode.
#*8725# = Switches USBACM to Loop-back mode.
#*3838# = Blinks 3D030300 in RED.
#*2077# = GPRS Switch.
#*2027# = GPRS Switch.
#*0227# = GPRS Switch.
#*0277# = GPRS Switch.
#*8370# = Tfs4.0 Test 0.
#*8371# = Tfs4.0 Test 1.
#*8372# = Tfs4.0 Test 2.
#*8373# = Tfs4.0 Test 3.
#*8374# = Tfs4.0 Test 4.
#*8375# = Tfs4.0 Test 5.
#*8376# = Tfs4.0 Test 6.
#*8377# = Tfs4.0 Test 7.
#*8378# = Tfs4.0 Test 8.
#*8379# = Tfs4.0 Test 9.
#*7878# = FirstStartup. (0=NO, 1=YES)
#*3838# = Blinks 3D030300 in RED.
#*2077# = GPRS Switch.
#*2027# = GPRS Switch.
#*0227# = GPRS Switch.
#*0277# = GPRS Switch.
#*22671# = AMR REC START.
#*22672# = Stop AMR REC. (File name: /a/multimedia/sounds/voice list/ENGMODE.amr)
#*22673# = Pause REC.
#*22674# = Resume REC.
#*22675# = AMR Playback.
#*22676# = AMR Stop Play.
#*22677# = Pause Play.
#*22678# = Resume Play.
#*77261# = PCM Rec Req.
#*77262# = Stop PCM Rec.
#*77263# = PCM Playback.
#*77264# = PCM Stop Play.
#*22679# = AMR Get Time.
*#8999*364# = Watchdog ON/OFF.
*#8999*427# = WATCHDOG signal route setup.
*2767*226372# = Camera Reset. (deletes photos)
*2767*3855# = E2P Full Reset.
*2767*2878# = E2P Custom Reset.
*2767*927# = E2P Wap Reset.
*2767*226372# = E2P Camera Reset.
*2767*688# = Reset Mobile TV.
#7263867# = RAM Dump. (On or Off)
~Samsung Mobile Lock Codes~
*#7465625# = Check the locks.
*7465625*638*Code# = Enables Network lock.
#7465625*638*Code# = Disables Network lock.
*7465625*782*Code# = Enables Subset lock.
#7465625*782*Code# = Disables Subset lock.
*7465625*77*Code# = Enables SP lock.
#7465625*77*Code# = Disables SP lock.
*7465625*27*Code# = Enables CP lock.
#7465625*27*Code# = Disables CP lock.
*7465625*746*Code# = Enables SIM lock.
#7465625*746*Code# = Disables SIM lock.
*7465625*228# = Activa lock ON.
#7465625*228# = Activa lock OFF.
*7465625*28638# = Auto Network lock ON.
#7465625*28638# = Auto Network lock OFF.
*7465625*28782# = Auto subset lock ON.
#7465625*28782# = Auto subset lock OFF.
*7465625*2877# = Auto SP lock ON.
#7465625*2877# = Auto SP lock OFF.
*7465625*2827# = Auto CP lock ON.
#7465625*2827# = Auto CP lock OFF.
*7465625*28746# = Auto SIM lock ON.
#7465625*28746# = Auto SIM lock OFF.
~Samsung Mobile MMS Codes~
*2767*43927# = Austria WAP Settings.
*2767*420927# = Czech WAP Settings.
*2767*33927# = France WAP Settings.
*2767*49927# = Germany WAP Settings.
*2767*30927# = Greece WAP Settings.
*2767*39927# = Italy WAP Settings.
*2767*31927# = Netherlands WAP Settings.
*2767*351927# = Portugal WAP Settings.
*2767*7927# = Russia WAP Settings.
*2767*34927# = Spain WAP Settings.
*2767*46927# = Sweden WAP Settings.
*2767*44927# = UK WAP Settings.
*2767*380927# = Ukraine WAP Settings.
*2767*73738927# = WAP Settings Reset.
*2767*43667# = Austria MMS Settings.
*2767*420667# = Czech MMS Settings.
*2767*33667# = France MMS Settings.
*2767*49667# = Germany MMS Settings.
*2767*30667# = Greece MMS Settings.
*2767*39667# = Italy MMS Settings.
*2767*31667# = Netherlands MMS Settings.
*2767*351667# = Portugal MMS Settings.
*2767*7667# = Russia MMS Settings.
*2767*34667# = Spain MMS Settings.
*2767*46667# = Sweden MMS Settings.
*2767*44667# = UK MMS Settings.
*2767*380667# = Ukraine MMS Settings.
~Samsung Mobile Sound Codes~
Dial *#6984125*#
Test menu dial *#9072641*# (You need this one i think.)
Click 5 Audio - 2 AP volume config
Now you see zie je 4 things:
1 RCV config
2 EAR config
3 SPK config
4 BTH config
Now you see this:
1 MP volume
2 Keytone volume
3 Ringtone volume
4 Rec volume
5 FM radio volume
6 Camera volume
7 Voice call volume
8 Vt call volume
9 Voice memo volume
( SPK = Speaker )( Ear = Headset )
Tune Headset volume:
*#9072641*# - 2 EAR config - 3 Ringtone volume - Stap 6 tune it to 10
Tune movie volume:
*#9072641*# - 3 SPK config - 3 Ringtone volume - Stap 6 tune it to 10
Note it works but don't forget to type somewhere your old settings.
~Samsung Mobile Email Codes~
#*36245# Turns Email TestMenu on.
*2767*22236245# Email EPP set (....)!
*2767*837836245# Email Test Account!
*2767*29536245# Email Test2 Account!
*2767*036245# Email EPP reset!
*2767*136245# Email EPP set (1)!
*2767*736245# Email EPP set (7)!
*2767*3036245# Email...
*2767*3136245# Email...
*2767*3336245# Email...
*2767*3436245# Email...
*2767*3936245# Email...
*2767*4136245# Email...
*2767*4336245# Email...
*2767*4436245# Email...
*2767*4536245# Email...
*2767*4636245# Email...
*2767*4936245# Email...
*2767*6036245# Email...
*2767*6136245# Email...
*2767*6236245# Email...
*2767*6336245# Email...
*2767*6536245# Email...
*2767*6636245# Email...
*2767*8636245# Email...
*2767*85236245# Email...
Don't work...
luckyduck69 said:
~Samsung Mobile Global Codes~
*#1234# = Firmware Version.
*#2222# = H/W Version.
*#8999*8376263# = All Versions Together.
*#8999*8378# = Test Menu.
*#4777*8665# = GPSR Tool.
*#8999*523# = LCD Brightness.
*#8999*377# = Error Menu.
*#8999*327# = EEP Menu.
*#8999*667# = Debug Mode.
*#92782# = PhoneModel. (Wap)
#*5737425# = JAVA Mode.
*#2255# = Call List.
*#232337# = Bluetooth MAC Adress.
*#5282837# = Java Version.
#*4773# = Incremental Redundancy.
#*7752# = 8 PSK uplink capability bit.
#*7785# = Reset wakeup & RTK timer cariables/variables.
#*7200# = Tone Generator Mute.
#*3888# = BLUETOOTH Test mode.
#*7828# = Task screen.
#*#8377466# = S/W Version & H/W Version.
#*2562# = Restarts Phone.
#*2565# = No Blocking? General Defense.
#*3353# = General Defense, Code Erased.
#*3837# = Phone Hangs on White screen.
#*3849# = Restarts Phone.
#*3851# = Restarts Phone.
#*3876# = Restarts Phone.
#*7222# = Operation Typ: (Class C GSM)
#*7224# = !!! ERROR !!!
#*7252# = Operation Typ: (Class B GPRS)
#*7271# = CMD: (Not Available)
#*7274# = CMD: (Not Available)
#*7337# = Restarts Phone. (Resets Wap Settings)
#*2787# = CRTP ON/OFF.
#*2886# = AutoAnswer ON/OFF.
#*3737# = L1 AFC.
#*5133# = L1 HO Data.
#*7288# = GPRS Detached/Attached.
#*7287# = GPRS Attached.
#*7666# = White Screen.
#*7693# = Sleep Deactivate/Activate.
#*7284# = L1 HO Data.
#*2256# = Calibration info? (For CMD set DEBUGAUTONOMY in cihard.opt)
#*2286# = Databattery.
#*2527# = GPRS switching set to (Class 4, 8, 9, 10)
#*2679# = Copycat feature Activa/Deactivate.
#*3940# = External looptest 9600 bps.
#*4263# = Handsfree mode Activate/Deactivate.
#*4700# = Please use function 2637.
#*7352# = BVMC Reg value (LOW_SWTOFF, NOMINAL_SWTOFF)
#*2558# = Time ON.
#*3370# = Same as 4700.
#*3941# = External looptest 115200 bps
#*5176# = L1 Sleep.
#*7462# = SIM Phase.
#*7983# = Voltage/Freq.
#*7986# = Voltage.
#*8466# = Old Time.
#*2255# = Call Failed.
#*5187# = L1C2G trace Activate/Deactivate.
#*5376# = DELETE ALL SMS!!!!.
#*6837# = Official Software Version: (0003000016000702)
#*7524# = KCGPRS: (FF FF FF FF FF FF FF FF 07)
#*7562# = LOCI GPRS: (FF FF FF FF FF FF FF FF FF FF FF FE FF 01)
#*2337# = Permanent Registration Beep.
#*2474# = Charging Duration.
#*2834# = Audio Path. (Handsfree)
#*3270# = DCS Support Activate/Deactivate.
#*3282# = Data Activate/Deactivate.
#*3476# = EGSM Activate/Deactivate.
#*3676# = FORMAT FLASH VOLUME!!!
#*4760# = GSM Activate/Deactivate.
#*4864# = White Screen.
#*5171# = L1P1.
#*5172# = L1P2.
#*5173# = L1P3.
#*7326# = Accessory.
#*7683# = Sleep variable.
#*8465# = Time in L1.
#*2252# = Current CAL.
#*2836# = AVDDSS Management Activate/Deactivate.
#*3877# = Dump of SPY trace.
#*7728# = RSAV.
#*2677# = Same as 4700.
#*3728# = Time 2 Decod.
#*3725# = B4 last off.
#*7372# = Resetting the time to DPB variables.
#*7732# = Packet flow context bit Activate/Deactivate.
#*6833# = New uplink establishment Activate/Deactivate.
#*3273# = EGPRS multislot. (Class 4, 8, 9, 10)
#*7722# = RLC bitmap compression Activate/Deactivate.
#*2351# = Blinks 1347E201 in RED.
#*4472# = Hysteresis of serving cell: 3 dB
#*2775# = Switch to 2 inner speaker.
#*9270# = Force WBS.
#*7878# = FirstStartup. (0=NO, 1=YES)
#*3757# = DSL UART speed set to. (LOW, HIGH)
#*8726# = Switches USBACM to Normal.
#*8724# = Switches USBACM to Generator mode.
#*8727# = Switches USBACM to Slink mode.
#*8725# = Switches USBACM to Loop-back mode.
#*3838# = Blinks 3D030300 in RED.
#*2077# = GPRS Switch.
#*2027# = GPRS Switch.
#*0227# = GPRS Switch.
#*0277# = GPRS Switch.
#*8370# = Tfs4.0 Test 0.
#*8371# = Tfs4.0 Test 1.
#*8372# = Tfs4.0 Test 2.
#*8373# = Tfs4.0 Test 3.
#*8374# = Tfs4.0 Test 4.
#*8375# = Tfs4.0 Test 5.
#*8376# = Tfs4.0 Test 6.
#*8377# = Tfs4.0 Test 7.
#*8378# = Tfs4.0 Test 8.
#*8379# = Tfs4.0 Test 9.
#*7878# = FirstStartup. (0=NO, 1=YES)
#*3838# = Blinks 3D030300 in RED.
#*2077# = GPRS Switch.
#*2027# = GPRS Switch.
#*0227# = GPRS Switch.
#*0277# = GPRS Switch.
#*22671# = AMR REC START.
#*22672# = Stop AMR REC. (File name: /a/multimedia/sounds/voice list/ENGMODE.amr)
#*22673# = Pause REC.
#*22674# = Resume REC.
#*22675# = AMR Playback.
#*22676# = AMR Stop Play.
#*22677# = Pause Play.
#*22678# = Resume Play.
#*77261# = PCM Rec Req.
#*77262# = Stop PCM Rec.
#*77263# = PCM Playback.
#*77264# = PCM Stop Play.
#*22679# = AMR Get Time.
*#8999*364# = Watchdog ON/OFF.
*#8999*427# = WATCHDOG signal route setup.
*2767*226372# = Camera Reset. (deletes photos)
*2767*3855# = E2P Full Reset.
*2767*2878# = E2P Custom Reset.
*2767*927# = E2P Wap Reset.
*2767*226372# = E2P Camera Reset.
*2767*688# = Reset Mobile TV.
#7263867# = RAM Dump. (On or Off)
~Samsung Mobile Lock Codes~
*#7465625# = Check the locks.
*7465625*638*Code# = Enables Network lock.
#7465625*638*Code# = Disables Network lock.
*7465625*782*Code# = Enables Subset lock.
#7465625*782*Code# = Disables Subset lock.
*7465625*77*Code# = Enables SP lock.
#7465625*77*Code# = Disables SP lock.
*7465625*27*Code# = Enables CP lock.
#7465625*27*Code# = Disables CP lock.
*7465625*746*Code# = Enables SIM lock.
#7465625*746*Code# = Disables SIM lock.
*7465625*228# = Activa lock ON.
#7465625*228# = Activa lock OFF.
*7465625*28638# = Auto Network lock ON.
#7465625*28638# = Auto Network lock OFF.
*7465625*28782# = Auto subset lock ON.
#7465625*28782# = Auto subset lock OFF.
*7465625*2877# = Auto SP lock ON.
#7465625*2877# = Auto SP lock OFF.
*7465625*2827# = Auto CP lock ON.
#7465625*2827# = Auto CP lock OFF.
*7465625*28746# = Auto SIM lock ON.
#7465625*28746# = Auto SIM lock OFF.
~Samsung Mobile MMS Codes~
*2767*43927# = Austria WAP Settings.
*2767*420927# = Czech WAP Settings.
*2767*33927# = France WAP Settings.
*2767*49927# = Germany WAP Settings.
*2767*30927# = Greece WAP Settings.
*2767*39927# = Italy WAP Settings.
*2767*31927# = Netherlands WAP Settings.
*2767*351927# = Portugal WAP Settings.
*2767*7927# = Russia WAP Settings.
*2767*34927# = Spain WAP Settings.
*2767*46927# = Sweden WAP Settings.
*2767*44927# = UK WAP Settings.
*2767*380927# = Ukraine WAP Settings.
*2767*73738927# = WAP Settings Reset.
*2767*43667# = Austria MMS Settings.
*2767*420667# = Czech MMS Settings.
*2767*33667# = France MMS Settings.
*2767*49667# = Germany MMS Settings.
*2767*30667# = Greece MMS Settings.
*2767*39667# = Italy MMS Settings.
*2767*31667# = Netherlands MMS Settings.
*2767*351667# = Portugal MMS Settings.
*2767*7667# = Russia MMS Settings.
*2767*34667# = Spain MMS Settings.
*2767*46667# = Sweden MMS Settings.
*2767*44667# = UK MMS Settings.
*2767*380667# = Ukraine MMS Settings.
~Samsung Mobile Sound Codes~
Dial *#6984125*#
Test menu dial *#9072641*# (You need this one i think.)
Click 5 Audio - 2 AP volume config
Now you see zie je 4 things:
1 RCV config
2 EAR config
3 SPK config
4 BTH config
Now you see this:
1 MP volume
2 Keytone volume
3 Ringtone volume
4 Rec volume
5 FM radio volume
6 Camera volume
7 Voice call volume
8 Vt call volume
9 Voice memo volume
( SPK = Speaker )( Ear = Headset )
Tune Headset volume:
*#9072641*# - 2 EAR config - 3 Ringtone volume - Stap 6 tune it to 10
Tune movie volume:
*#9072641*# - 3 SPK config - 3 Ringtone volume - Stap 6 tune it to 10
Note it works but don't forget to type somewhere your old settings.
~Samsung Mobile Email Codes~
#*36245# Turns Email TestMenu on.
*2767*22236245# Email EPP set (....)!
*2767*837836245# Email Test Account!
*2767*29536245# Email Test2 Account!
*2767*036245# Email EPP reset!
*2767*136245# Email EPP set (1)!
*2767*736245# Email EPP set (7)!
*2767*3036245# Email...
*2767*3136245# Email...
*2767*3336245# Email...
*2767*3436245# Email...
*2767*3936245# Email...
*2767*4136245# Email...
*2767*4336245# Email...
*2767*4436245# Email...
*2767*4536245# Email...
*2767*4636245# Email...
*2767*4936245# Email...
*2767*6036245# Email...
*2767*6136245# Email...
*2767*6236245# Email...
*2767*6336245# Email...
*2767*6536245# Email...
*2767*6636245# Email...
*2767*8636245# Email...
*2767*85236245# Email...
Click to expand...
Click to collapse
Nearly all of these codes don't work on my sgs4g... Im running GB 2.3.5 ROM with KJ1 kernel. Does that make a difference?
Search sgs secret codes on the market.
Sent from my SGH-T959V using xda premium
Please use the Q&A Forum for questions Thanks
Moving to Q&A
I came across a build.prop tweak for preferred data connection
Code:
ro.telephony.default_network=
0 = WCDMA Preferred
1 = GSM Only
2 = WCDMA Only
3 = GSM/WCDMA (auto mode, according to PRL)
4 = CDMA / EVDO. Preferred
I have a Nexus S 4G CDMA Sprint version and im wondering if I should set it to choice 4 or to choice 2. Whats do you guys have?
Discuss
Mine is set to GSM only. Mine always defaults to GSM only now for some reason. It used to stay on option 3. Not that there was any difference. Just try both out and see what happens.
Sent by pocket technology.
I must configure an SIII to work on GSM network by default. I can change the network mode in the phone info, but when I turn off the device, it back to the default.
I looked for a way to do this using the build.prop and found the following line:
Code:
ro.telephony.default_network = 8
I know that this line defines the network mode, but do not know what value to use. In case the default is LTE / CDMA and wanna leave LTE / GSM. Logically it should be 9, but didn't work.
Does anyone know the correct values?
Solved!
Set it to 3 and worked, network mode is GSM auto (PRL) as default