3.5mm jack - TG01 Accessories

is there a .cab needed to use the 3.5mm jack? i ordered a motorola micor usb to 3.5 and a samsung. both doesnt work. any ideas why?

Yes i bought that too only to find out it didn't work. I don't think this incompatibility is software related though.

dinhy34 said:
is there a .cab needed to use the 3.5mm jack? i ordered a motorola micor usb to 3.5 and a samsung. both doesnt work. any ideas why?
Click to expand...
Click to collapse
No .cab required. You have to have a correctly wired micro USB to 3.5mm adapter. You also need to have a load (earphones, amp, etc.) which presents a sufficient impedance to the TG01 for it to recognise that there is an analogue audio device attached. That causes the TG01 to switch tehe function of the uUSB port from Data to analogue audio. If you plug in a typical 4 or 8 Ohm laptop extension speaker or some low impedance earphones it will not work.
There have been lots of discussions around this subject both on XDA and other Forums such as ModaCo and Brighthand.
This post on XDA includes a couple of links to the principle ones.
Hope that helps.

Related

Tilt External Speakers

I am wondering if it is possible to use the USB connection on the Tilt for attcahing it to external speakers. Is there any audio output directed throgh the USB port?
If not, can anyone recommend a blue tooth device that will allow communication from the Tilt and end up into an Ipod style jack that I can then plug into the Ipod port of the stereo system in my truck? (No factory blue tooth.)
Thanks to all.
AndyInFl said:
I am wondering if it is possible to use the USB connection on the Tilt for attcahing it to external speakers. Is there any audio output directed throgh the USB port?
If not, can anyone recommend a blue tooth device that will allow communication from the Tilt and end up into an Ipod style jack that I can then plug into the Ipod port of the stereo system in my truck? (No factory blue tooth.)
Thanks to all.
Click to expand...
Click to collapse
Tilt's USB port has audio out. I use 8525's usb headset that I had laying around to listen to songs at work.
Thanks for the reply!
I will try to find a headset. I can then cut the headphones and attach an audio input instead of the earphones.
Can you recommend a brand other than the factory set?
Also, would anyone know where I can find the USB port layout?
Thanks again to all.
I cut the usb plug off my old htc herald headphones and put a 3.5mm jack on the other end. I then bought a cheap mp3 dock with speakers. Plug the usb jack into the tilt and the 3.5mm into the dock. The sound is pretty darn good. The dock works off 4 aaa batteries and gives me 8 hours of tunes. heres a pic with my old mda in it, it works just fine with my tilt also.
Someone should make a HTC dock with speakers that runs off batteries so its portable. I bet they could sell a few.
Adapters for the Tilt/8925 are available all over the web. USB on one end, 2.5mm or 3.5mm on the other. You can get them for 6 bucks here: http://www.tiltdepot.com/
adapter
I have a kaiser and just got the usb to 3.5mm adapter for 7bucks. I have a tape deck in my car so I bought a ipod tape to 3.5mm adapter now I have music and can run tomtom too even at the same time through the car speakers. I like that dock too!

3.5mm Jack vs HTC plug

given that the sprint has a 3.5mm jack for earphones, does the standard htc plug (where you charge / sync) also have a connection to listen to music? and if yes, does that then mean that we can plug in 2 sets of earphones? one on the 3.5mm and one on the htc mini- usb jack? i don't have standard htc headsets and i'm tempted to buy a set just to check...
cheers
I was able to test this with my headphones from my old Mogul and yes, it does work with both headphones connected at the same time -- audio from both.
HTH
thanks mate! now i can go ahead and buy a set. it actually provides a good alternative to continuous plugging and unplugging from the 3.5 jack. there is also bluetooth but the mini-usb gives me another option for tunez.
cheers
I got curious and tried it.
Can't figure out why you'd need it, but it works on my usc tp2
g2tl said:
I got curious and tried it.
Can't figure out why you'd need it, but it works on my usc tp2
Click to expand...
Click to collapse
thanks mate, just tried it and it works fine as well. as to where i would use it:
1) gives me an alternative to constantly plug into the 3.5mm jack. ages ago i read that the plug connections eventually wear out. not sure about statistics and all though for the tp2. but a mate of mine did return his 6-month old unit for this reason. claims that one day the sounds were all gone. only by plugging in his headphones did he hear anything. he sent it back for replacement and the diagnosis showed that the plug connections were worn out. well in all fairness he did listen to his tunez 2 times a day...that meant plugging in and out twice a day as well. seems the phone was "stuck" in headset mode.
2) i use an i-tech bluetooth set of which i can plug in my noise cancellers. if the battery ran out, i can then plug into the 3.5mm. or, i recently got a mini-usb to 3.55mm headset converter. again, good alternative to constantly plugging into the 3.5 jack
3) my wife =) on a recent trip to canada...of which took ages...we shared the headset plugged into the 3.5 jack. by plugging into the mini-usb, that way we can both have our own headsets at the same time. quite weird to have one ear listening to tunez while the other being bombarded by sounds from the plane =)
cheers mate
Sorry, I did not see the previous replies ...
TP2 uses USB-B for charging and syncing. This USB-B has audio out as well as video out. I don't know if one takes priority over the other (USB-B audio or 3.5mm audio out), or if both can be used together.
Last week I ordered a USB-B cable to output video/audio to external monitor & speakers (watch movies externally) via RCA jacks (Right/Left/Video).
Why not just use a 3.5mm audio splitter jack to get dual out audio? (personally, I'd rather put wear & tear on a 3.5mm audio jack than a mini-USB jack ...). Seems a 3.5mm splitter would be simple clean output method. Additionally, you could use BT-Audio paired possibly to more than one device headset for dual audio out ...?

MWG Zinc-II Need help for attaching miniUSB to 3.5mm adapter

Hi
I wanted to buy a mini-usb to 3.5mm audio adapter for Zinc-ii phone so that I can use my regular headset for listening songs. I couldn't find a mini-usb adapter for Zinc-ii but I got one generalized adapter (mini-usb to 3.5mm audio). When I attached the adapter to Zinc-ii, it is not routing the audio through the adapter. It triggered the activesync tool first time and it failed for obvious reason because it is a 3.5mm adapter not a computer.
1. Is there any setting which I have to do for routing the audio through the adapter?
2. Is there a place where I can buy a 3.5mm audio adapter if there is a special one for zinc-ii? The headset came with the device is working perfectly fine.
Thanks
i made myself a cable using the original zinc2 headphones get a solder ,wires and 3.5 plug dats it ... or i cud sell mine for lets say 10 gbp + delivery ... i got htc now
Thanks. I will settle for Acoustic Research bluetooth minibridge available in circuitycity website selling for $20

[Q] Line In Recording

Is it possible to use the 3.5mm jack on the Nexus 5 as an input source for recording?
Like connecting it to a guitar.
Thanks in advance.
I don't know, but would be curious to know the answer.
Do you have a piece of hardware that you could test it with?
Sent from my Nexus 5 using xda app-developers app
tried but didn't work...
could be a TRS TRRS problem... not sure...
related?
http://forum.xda-developers.com/showthread.php?t=1100322
the n5 is out of my hands right now, can someone test this...? thx in advance.
loyukfai said:
Is it possible to use the 3.5mm jack on the Nexus 5 as an input source for recording?
Like connecting it to a guitar.
Thanks in advance.
Click to expand...
Click to collapse
I believe the only way is via USB...but you have to use an app as Android does not build in USB recording as does Windows. I use this app along with a USB interface and a microphone on this phone and my tablet. Works great and the dev is a great guy. He also makes a DAW (there's a free version) for recording and editing.
that's... too bad then. thanks for info but.
btw, any suggestion for usb audio in? or usb mic? thx.
anyone? " _ "
I use a pair of wired ear buds that have a built in microphone for calls. I'm running CM11 not stock but I just tested and "Sound Recorder" is more than happy to receive its input via the headset jack. I would believe it's just a matter of finding the right converter plug for your guitar.
thionylx said:
I use a pair of wired ear buds that have a built in microphone for calls. I'm running CM11 not stock but I just tested and "Sound Recorder" is more than happy to receive its input via the headset jack. I would believe it's just a matter of finding the right converter plug for your guitar.
Click to expand...
Click to collapse
I have used ASR for recording, works fine over the headset jack. It is a mono source of course. It won't work with a standard 3.5mm plug of course, you have to have the signal on the microphone portion - which is ground (silence) for the standard plugs.
I used the adapter that came with Dragon Naturally Speaking. It has two 3.5mm stereo plugs to one 3.5mm stereo+mic plug. If you use a 3.5mm stereo cable into the mic side of this adapter it works fine.
You could probably rig up something from Radio Shack, but I didn't have to because this worked, and I don't need the adapter for my computer so it was just sitting in the cord box...
thanks to everyone who replied, truly.
it seems that there are 2 solutions...
1) usb sound w/dedicated app
2) cable that turns L/R input from TRS tip to M input on TRRS tip
the 3.5mm/trrs/(left/right/ground/mic) socket on the phone should work as tdcrone mentioned above. as long as a 3.5mm stereo+mic adapter available, or a custom cable that turns the original L or R input into M on the output end.
this is by far the simpler solution, **if such cable or adapter is available**, the caveat emptor is that the record will be mono, and there could be mic gain issues...?
otoh, the usb solution works, at the cost of having to get an adapter and apps for android costs.
@Vegasden: i see that both USB audio recorder pro and audio evolution mobile daw seem to work with usb recorder, and the latter one is just marginally more expensive?
edit: sorry, just realise that one also needs to buy usb audio recorder pro if she/he wants to use audio evolution mobile daw to do usb record
Is me again.
Do you think these will work? They claim to support iPhone only...
http://www.ikmultimedia.com/products/irig/
http://www.cherubtechnology.com/product_detail.php?id=96
Cheers.
This (http://www.cherubtechnology.com/product_detail.php?id=96) works, tested okay.
Cheers.

USB Type C to 3.5mm Headphone Jack Adapter

My issue
Hi everyone, I have a Nexus 6P and want to route my audio through a USB type C converter to 3.5mm headphone Jack. I have purchased one online, but it doesn't seem to be working. I have seen that the Moto Z has this adapter and I assumed one I found online would be compatible with my 6P. The reason I want to do this is because I prefer for the AUX jack to come out the bottom of my phone.
What I have tired
Changed 'Select USB Configuration' to all the different options and tried playing music.
Tried 'audio routing' apps from the app store
What I would like to know
Is this because I need to change a setting in my phone to route music out of the USB C?
Do I need to get some kind of DAC to allow support for this?
Has anyone else tried this with their phone?
Thanks
broj0nes
Subscribed. Interested in the solution.
Sent from my Nexus 6P using Tapatalk
If you don't mind my asking, why bother?
eregev said:
If you don't mind my asking, why bother?
Click to expand...
Click to collapse
One reason is that to me it makes more sense to put your phone upside down into you pocket. I've always done this at least. So when listening to music I have to put it the other way round. I have also heard the USB C port offers better sound quality.
brotherj0nes said:
One reason is that to me it makes more sense to put your phone upside down into you pocket. I've always done this at least. So when listening to music I have to put it the other way round. I have also heard the USB C port offers better sound quality.
Click to expand...
Click to collapse
Re:sound quality, you'd possibly see a quality increase if you use an external Digital to Analogue Converter or fully usb-c headphones. BUT, if you're using a little dongle (if it's possible), then the phone is still managing the analogue conversion and, thus, a very similar quality of audio output. Now I don't know of the 6p's ability to pipe it straight out iPhone 7 style through a dongle, but short of buying a DAC and going whole-hog on an audio upgrade, I'd just flip your phone the other way in your pocket and go the standard route.
Just my $.02
I have been looking for a solution to this too and I seem to have found one. I poked around on Amazon and I think I finally found adapters that work, here's the link https://goo.gl/QT2ith This the only one with positive reviews so when it comes in on the 30th I'll let all of you know.
sgandy2989 said:
I have been looking for a solution to this too and I seem to have found one. I poked around on Amazon and I think I finally found adapters that work, here's the link https://goo.gl/QT2ith This the only one with positive reviews so when it comes in on the 30th I'll let all of you know.
Click to expand...
Click to collapse
Looks quite similar to the one that I got. Hopefully it works for you! Let me know how it goes
I read recently that the current implementation of audio over USB-C isn't very efficient or battery friendly. There's a new spec being ratified to provide audio like the iphone can. Hopefully that's a firmware change and not a hardware one.
http://www.theverge.com/2016/8/17/12519936/intel-usb-type-c-headphone-jack-replacement-idf-2016
I don't think it's possible on the 6P, not without using a USB DAC anyway.
As far as I'm aware, the adapter you have is for a USB 3/3.1 interface. While the 6P has USB-C it is USB 2.
I'm able to get audio out of my USB C port, but it's with a USB headset. Haven't tried it with a 3.5mm headphone adapter, but havd no reason to try it either.
This is weird. Because i have a pair of Sennheiser Urbanites (Wireless edition), and i can use bluetooth, aux, and usb (like for a computer) audio. I once tried to turn off the headsets (bluetooth off, aux and usb still works if connected), and turned off bluetooth on my phone. Then i used my USB type C to USB type A Female adapter (from the google store), and connected the usb-cable from the headsets into the type c adapter. it did output audio through the usb-cable.
Mgrev said:
This is weird. Because i have a pair of Sennheiser Urbanites (Wireless edition), and i can use bluetooth, aux, and usb (like for a computer) audio. I once tried to turn off the headsets (bluetooth off, aux and usb still works if connected), and turned off bluetooth on my phone. Then i used my USB type C to USB type A Female adapter (from the google store), and connected the usb-cable from the headsets into the type c adapter. it did output audio through the usb-cable.
Click to expand...
Click to collapse
Bluetooth headphones usually have their own DAC, so the audio for all but the Aux is still being sent through the DAC first, which is supported by older USB standards.
The new USB 3.1 Audio standard can pass through analogue audio from the internal DAC, which is what I believe phones such as the Moto Z utilise. Otherwise the adapter would require it's own DAC, which would make it far larger and more expensive.
Not sure if you will find a good solution at the moment since they just created a standard for audio over usb c http://www.businesswire.com/news/home/20160927006252/en/USB-IF-Announces-USB-Audio-Device-Class-3.0
Did the amazon converter end up working for you?
My experience so far.
Hi, I ordered some usb c to 3.5mm & out of the box so far they aren't working. I tried Neutron and tried to force the audio to usb but unsuccessfully with phone not recognizing the USB connection.
On the other hand the type C to usb-a adapter worked beautifully using mixplorer. If I get working, will update. Thanks.

Categories

Resources