i tried to set up htc hd rom on my device ( kaiser )
after booting from my device
it work normally till the 1st third on stripe at booting screen
then this message appear
" the update is failed and terminated "
i made restart
but the phone doesn`t work after this
what shall i do
please help me
You should put a rom specific to your phone, not just another one. In this case you tried to install a Htc HD rom? WTF?!
Anyway, you have a sub-forum dedicated to Kaiser. Go ahead post your message there.
Good luck!
Related
Hey guys,Yesterday i wanted to update my rom.I have windows mobile 6.1.Apperently with the new rom it makes it faster.I unlocked my device and tried loading the softawre on.Everytime i try loading it ,the computer says it lost the connection with the pc.Today i tried using my phone and when i switch my phone on ,the phone does not respond and the screen has three colour(blue,red etc).How do i get into my phone or reset it so that i can use my existing rom and windows?e-mail me anytime
You're stuck in Bootloader
Hi
Your phone is stuck in Bootloader Mode. You may find that by removing the battery and re-inserting it you will get to a position of loading Windows Mobile. The Bootloader is the software on the phone that is used to install a new operating system. If you search for "Stuck" and "Bootloader" on the forum or the section of your device you will probably come up with some threads about this problem.
The worst case scenario is that the "flash" of the new operating system has gone wrong so the Windows Mobile operating system can not load. If this is the case, the phone will automatically revert to the Bootloader as it can't "see" any system installed. Think of a PC reverting to the BIOS and giving you the message "Operating System Not Found" if you remove or disconnect the hard drive.
If you can't boot simply be doing a soft reset using the stylus in the hole you need to successfully flash a new Operating System or ROM. Check out the Encyclopedia at the bottom of the main forum page if you don't understand any of the words I've used here. If you can be more specific about your device and the ROM you tried to flash others may be able to help.
Cheers
andrew-in-woking
Help
Hi,how do i flash when i dont have excess to windows itself?The colourful screen comes on immidiately when i start my phone!!
XZ5J4H said:
Hi,how do i flash when i dont have excess to windows itself?The colourful screen comes on immidiately when i start my phone!!
Click to expand...
Click to collapse
Welcome to the forum
Please READ the Wiki: http://wiki.xda-developers.com/index.php?pagename=HTC_Vox
Over there you´ll dind a way to flash your device
Good luck,
Stuck windows
Hi,I managed to load mono lisa windows 6.1 on my phone.I did this by justing loading utility update file.Followed all the intructions.After the rebooted it just goto stuck.I tried taking the batery out and inserting it back in the phone after 10 seconds.The problem is when i start my phone it gets stuck and the everything in unresponsive.Help me please!!1
Hard Reset or Reflash
Hi
After flashing a ROM you always need to perform a manual Hard Reset. Read the Wiki page on your device for info on how to do this. If that doesn't help then you may have a bad flash. If this is the case then flash the ROM again but as soon as it's done perform a manual hard reset.
If you still can't get it working flash an official operators or HTC ROM to your device.
G'luck!
andrew-in-woking
Rom Wanted
Hi Guys,what is the latest and best rom for a htc s710 today?I want to upgrade.Please help!!Want something that also makes my phone faster.Currently have the VOXrOMwM6.1 cLEAN_V1.3
XZ5J4H said:
Hi Guys,what is the latest and best rom for a htc s710 today?I want to upgrade.Please help!!Want something that also makes my phone faster.Currently have the VOXrOMwM6.1 cLEAN_V1.3
Click to expand...
Click to collapse
Enter to Vox forum and READ a little about all ROM´s there.
The best way is to test severals till you get the one fits your personal needs
Good luck,
Well I've tried everything possible, updated device manager fro vista. MDA Vario 3, connects for active sync but after running KaiserCustomRUU.exe. where it update the crrunt ROM version... it changes the screen into 3 color screen , after few minutes in the same condition............ 0% process........ and then........... shows me an error message as under:
ERROR [262]: UPTAE ERROR
The ROM update utility has encountered communication errors during the update process. The program will guide you step-by-
step to recover from the errors so you can continue the update.
and i need to restart MDA. although on recovery process it directly come to normal screen instead of 3 color screen, which means (i guess) it never started changing ROM current picture.
Any help about it plz.
Regards
Iaan
iskhan said:
Well I've tried everything possible, updated device manager fro vista. MDA Vario 3, connects for active sync but after running KaiserCustomRUU.exe. where it update the crrunt ROM version... it changes the screen into 3 color screen , after few minutes in the same condition............ 0% process........ and then........... shows me an error message as under:
ERROR [262]: UPTAE ERROR
The ROM update utility has encountered communication errors during the update process. The program will guide you step-by-
step to recover from the errors so you can continue the update.
and i need to restart MDA. although on recovery process it directly come to normal screen instead of 3 color screen, which means (i guess) it never started changing ROM current picture.
Any help about it plz.
Regards
Iaan
Click to expand...
Click to collapse
First did you do everything in this post?
iskhan said:
Well I've tried everything possible, updated device manager fro vista. MDA Vario 3, connects for active sync but after running KaiserCustomRUU.exe. where it update the crrunt ROM version... it changes the screen into 3 color screen , after few minutes in the same condition............ 0% process........ and then........... shows me an error message as under:
ERROR [262]: UPTAE ERROR
The ROM update utility has encountered communication errors during the update process. The program will guide you step-by-
step to recover from the errors so you can continue the update.
and i need to restart MDA. although on recovery process it directly come to normal screen instead of 3 color screen, which means (i guess) it never started changing ROM current picture.
Any help about it plz.
Regards
Iaan
Click to expand...
Click to collapse
you have vista then your prob better off flashing via sd, also you shouldn't have started a new thread to ask this question, this forum isn't intended for every time someone has a problem and searches and can't find the answer to start a new thread. PM someone you see posting that seems knowledgeable and ask that person if you can't find what you are looking for.
Flashing through SD is always the best. And its a lot safer than USB way.
Thanks for the help guys... closing thread as this issue can be fixed by reading the sticky and also the wiki..
Peace,
Josh
I have try to flash the unofficial rom. However, the phone rebooted during the update process. Now, my Acer s200 only can display the splash screen and cannot go into windows...
Anyways can flash the rom again?? I tried to use Acer_EUU.exe, but it need to detect the phone by Activesync. Anyways can flash the rom bypass activesync?
Some problem....
Hi!
I tried to flash from original EN ROM version on RU version and had the same problem - the device displayed Windows splash screen and then just reboot. So, I was confused but I didn't stop this process and after half an hour Windows loaded...(during this time I removed he battery and pushed soft-reset button a lotof times).
So, my only advice is to try to wait with re-booting device till the Windows boot and then to flash the original ROM (if you'll find it).
For me - after I loaded RU version of Windows I just flashed for custom EN ROM and it was OK (without this issue).
Good Luck!
It solves your problem..
DimICE said:
Hacked ACER_EUU.exe
Link: http://www.mediafire.com/?wy2yynnjz2z
ActiveSync connection is not needed!
Also is not needed to edit version.txt..
Just replace original ACER_EUU.exe with this file, execute it. Press next,next,ok,ok.. Message "Waiting for download mode coming" appear..
Power your Acer s200 with Power+Camera buttons pressed and connect to computer.
Tested on 2 acer s200 phones
Sorry for my English)))
Click to expand...
Click to collapse
link not working ( http://www.mediafire.com/?wy2yynnjz2z )
http://dimice.ru/ACER_EUU.exe
Rom update can be computer's fault
DimIce's program works perfectly. I've thought I bricked my phone many times, but always have been able to recover. This is what I recently discovered. In the middle of a flash, my computer said "write error". 'Thought my phone would stay dead. Finally, I switched to another computer and flashed the phone with no problem. So if you suffer a bad flash, simply change computers. If none is available, reboot your computer to clear the memory, etc. (by the way I'm using Windows 7 x64) and try again - sometimes even changing the USB port might help. The phone excels in it's ability to be re-flashed -even if you suffer disaster in the middle of a procedure.
As we dedicate only to HTC devices you won´t get too much attention.
Better try here:
http://www.eten-users.eu/
Good luck,
orb3000 said:
As we dedicate only to HTC devices you won´t get too much attention.
Better try here:
http://www.eten-users.eu/
Good luck,
Click to expand...
Click to collapse
Ignore this guy he has a bot setup for posting this on everyone that has 1 post or is posting in general or Upgrading, Modifying and Unlocking, You need to flash a rom based of the 1.00 oem drivers, flash this rom: http://forum.xda-developers.com/showthread.php?t=596304 and all of your problems will be solved, if not let me know and il help you out.
rafyvitto said:
Ignore this guy he has a bot setup for posting this on everyone that has 1 post or is posting in general or Upgrading, Modifying and Unlocking, You need to flash a rom based of the 1.00 oem drivers, flash this rom: http://forum.xda-developers.com/showthread.php?t=596304 and all of your problems will be solved, if not let me know and il help you out.
Click to expand...
Click to collapse
If you have any problem please take it to the council.
my only intention is to let new members know that this is an HTC forum only!
So they don't waste their time
If that bothers you, shame...
XDA has never meant to be HTC only.
Just open your eyes, dear sir.
I have a problem with the installation romu message pops up to me(sorry acer usb host driver must be installed in windows xp sp2 or later version please update os version to windows sp2)
stuck on clean boot screen
Hi, i was updating from EUU_Acer_S200_3.003b.00_EN_03.03.08_3.003.01_20100119 to EUU_Acer_S200_3.003c.00_ES_03.03.08_3.003c.00_20100201 but accidentally closed the acer's application, so the phone is stuck on "clean boot" screen? what should i do?, thank you!
Hi Everybody. This is my first post here
I own an HTC Touch (Vogue) from Orange (Spain) and I would like to install WM 6.1 on it. Orange does not provide with WM 6.1 and I found on the internet that there is a Sprint version of it, so I decided to install it. I get "Error 270" it says the image is corrupt. I tried to make an splxploit-windows and nothing happens... I took a screenshot (attached file) of what I get... and it stays there. Nothing happens at all.
I tried to install other versions also... HTC Magician and others just to see what happens and always I get "Error 270". The only one I could install successfuly is the Orange Rom
I tried everything and can´t find a solution. Any help there please?
Thanks a lot! =)
PD: I am using Windows XP, ActiveSync 4.5 and in SPLXPLOIT-WINDOWS I am following this steps (I get stuck in step 4)
1) manually start in bootloader mode
2) disable USB in activeSync
3) check 'usb' appears at the bottom of the tricolor screen and that he device is recognized by XP. If not, try unplugging/repluging
4) run the corrected unbrick.bat
5) while still in (new) tricolor screen after loader update, upload a new ROM
Any ideas?
This is not a complaint... this is just how I feel::
It is really frustrating to post something for 1st time in a forum looking for an answer and not to get anything in three days.
Welcome to forums
Have a deep read on Wiki here
Also visit Vouge section.
Read, Search, Respect and Enjoy!
hy i wanted to upgrade my rom so first of all i backed up my contacts bla bla, took out sim and sd card, hard reset of the htc x7500 all well , i started the device and followed instructions on screen, connected the usb synced perfectly. executed Athena wrapper.exe all went well completed , everything was working fine, then soft reset the device to check if all was ok (ps. setup already finished on pc and mobile) and guess what the green light at the joystick comes up but nothing else blank screen ( hep me what can i do from this point, i can enter the boot loader, if i connect the usb, in the white bit of the boot loader i get from serial change to usb but on pc nothing saying sync connected or anything like that. il try reinstalling the active sync on the computer see if that works .
oh great gurus of this forum please help me with this urgent matter
thank you anticipated
ps it is my first time doing this , i have it knowledge, and i read for 5 hours inos and how to's from the forum before i did this and it still happened this mysterious problem hopefully not terminal (((
I hope that you did not take the hard spl from this forum.
This subforum and releases are for the X7510.
no i took it from the X7500 section , anyway i solved the problem :d thanks to the instructions from here :
h ttp: //forum .xda-devel opers.com/show thread.php?t= 326953
Link from above just delete the spaces and there you have it, i could not post it together as i am a new member and does not let me put the link yet.
i followed the link in the firs post ( the one replied to the quoted text) downloaded from there the rom update and from bootloader screen it went like a charm, after that i upgraded the rom to 1.58 witch i dont quite like it as it keeps showing only H instead of 3G or the type of connection either the settings i setup in the phone, and installed the AP4 platinum ROM and works well. hope others will get their problems solved like this too as i saw there are many with the same problem.