Phone won't autosync - How do I load new ROM? - Touch Pro, Fuze General

I'm totally new to flashing phones, but having trouble with my touchpro.
When I load it up, it gets to a screen with the HTC logo and will not load my today screen. It's sluggish, won't autosync, and frustrating the hell out of me to be quite honest lol. The messaging and phone still works. Haven't tried the internet yet but everything takes ages to load. Also my unlock code to get into EPST (000000) will not take. Weird.
Anyways, I've decided I've had enough (this happened before) and just want to flash a new ROM to the phone. I've read the flashing for noobs article and it told me to autosync it up and use Hard-SPL. But I can't autosync - how should I go about doing this?
I'm not worried about backing anything up. I can get all my numbers back there eventually...
I mentioned that this problem has occurred with my phone before...usually I waited a day or two and the Today screen just showed up...but it's been a few days and it's not coming back....I think I am using Hofos or Holos or something like that as my current ROM for Cricket service if that helps....

Put your phone into bootloader mode (soft reset while holding down the power and volume down hard keys). You'll come to a tri-color screen that should read "serial" at the bottom. Connect phone to your computer and wait till it "serial" changes to "USB". Now run the Update Utility to flash the hard-spl and repeat for a new rom after unlocking it.

you can also do an SD card flash. check out the sticky for details.

I've never flashed HardSPL to the phone (at least not that I am aware of - I got this phone from someone else)...Will the bootloader still come up at first? And can I flash the phone without having hardspl on it?

bondra76 said:
I've never flashed HardSPL to the phone (at least not that I am aware of - I got this phone from someone else)...Will the bootloader still come up at first? And can I flash the phone without having hardspl on it?
Click to expand...
Click to collapse
Put the phone in bootloader. On the tri-colored screen, you should see SPL - 1.90 OLIPRO. If not, then the phone isnt unlocked. The phone has to be unlocked in order to flash a custom rom. Check the ROM development thread for more information. I should add that you need to make sure you have a CDMA phone or GSM phone. They use different unlockers. The OLIPRO one I mentioned above is GSM. The CDMA reads SPL - 0.37 CMONEX.

Cricket is cdma, isn't it? You better do some reading before flashing, because the single most critical thing you will do is flash hard spl. If you flash the wrong one, there is no going back and your phone will be toast. Go to PPC Geeks or the cdma forum here, and make sure you stay well away from the 1.90 Olinex hard spl.

Farmer Ted said:
Cricket is cdma, isn't it? You better do some reading before flashing, because the single most critical thing you will do is flash hard spl. If you flash the wrong one, there is no going back and your phone will be toast. Go to PPC Geeks or the cdma forum here, and make sure you stay well away from the 1.90 Olinex hard spl.
Click to expand...
Click to collapse
Thanks you're right it is CDMA. Thanks for the help tho guys I will head over to the CDMA forum

Related

please help i think i messed up my mda using the rom kitchen

I ran it according to farias instructions I thought. It flashed but now I cant install anything and I cannot write to the storage card or the phone, any cab i try to install is unsuccessful and I cannot save any files to the storage card or the phones memory.
And it appears that I cannot flash the rom again. Am I screwed?
What is you IPL / SPL? IS your phone a G3 or G4? Can you get to the bootloader? (turn off your phone (pull the battery if you have to) then hold the camera key down while you turn it on). You can flash directly to the bootloader (even though activesync won't connect.
BTW: If this stuff makes you nervous, you probably shouldn't be cooking... Your phone will do all sorts of weird stuff when you screw up a build. And you should really know how to recover from most things that can happen...
I have done this before, this is the first time I have ever had a problem. my IPL/SPL is 2.26. And the phone is unlocked.
beowolf said:
I have done this before, this is the first time I have ever had a problem. my IPL/SPL is 2.26. And the phone is unlocked.
Click to expand...
Click to collapse
ok, cool... wasn't sure... So can you get to the bootloader?
yes I can get to it
I am flashing back to the t-mobile 2.26 rom. Working so far, I will leave the cooking alone. Can you recommend a good wm6 rom that doesnt have any problems?
"doesn't have problems" is the catch
I'm partial to my own Crossbow Reloaded ones, but they aren't perfect. If you don't hit the keypad issue with 1.7 though, its pretty close
Core 2.0n is very good and nice and clean.
Also NBD and Wizard Mobile 6 are both supposed to work well.
The new "official" rom we are playing with is beta, but I have to say its really fast and we aren't seeing much wrong with it (but its only been 12 hours since its been released). There are a couple of issues that are fixed with cabs (CommManager for one).
As for cooking, you probably eith had something wrong in a .rgu or somesuch. Just takes a number of builds and flashes to get it right to where it boots (then you debug what you forgot in packages and start over )

Wont Boot

I am a little confused. I have been trying to get WM6 on my T-mobile Wizard and actually got TNT 1.1 loaded and was working fine. I found that I could no longer view my contacts. The page would appear and then as quickly as it appeared it disappeared.
So I figured, I at least got it this far. I will just reload this rom and see if perhaps something did load right. Well after the reload. The phone boots up to the splash screen with IPL\SPL numbers and just sits. NOTHING.
I left it there for like 2 hours and still nothing. But I can still get into the BootLoader.
My questions to you gurus is:
Is the phone fubared?
Can I do some kind of master reset?
Why would it tell me "Invalid Vendor ID" when trying to flash the orginal T-mobile rom?
Are there any tools that can help me out? Paid\free?
Please help!!! Seriously! Please HELP!!!
Very much appreciated.
Thanks
Drunknasty said:
I am a little confused. I have been trying to get WM6 on my T-mobile Wizard and actually got TNT 1.1 loaded and was working fine. I found that I could no longer view my contacts. The page would appear and then as quickly as it appeared it disappeared.
So I figured, I at least got it this far. I will just reload this rom and see if perhaps something did load right. Well after the reload. The phone boots up to the splash screen with IPL\SPL numbers and just sits. NOTHING.
I left it there for like 2 hours and still nothing. But I can still get into the BootLoader.
My questions to you gurus is:
Is the phone fubared?
Can I do some kind of master reset?
Why would it tell me "Invalid Vendor ID" when trying to flash the orginal T-mobile rom?
Are there any tools that can help me out? Paid\free?
Please help!!! Seriously! Please HELP!!!
Very much appreciated.
Thanks
Click to expand...
Click to collapse
if your device is G3, unlocking is required to flash any rom, before upgrade your device, it is recommended to flash an official WM5.0 rom (in your case T-Mobile rom) with IPL and SPL 2.xx then flash again.
in general there are many probabilities for your issue.
((Where is TNT1.1?? did you mean 1.0?? ))
My Bad meant 1.0
So to get it straight.... I will need to unlock my phone each time?
Oh and to correct myself again, when flashing with the T-mobile ROM it says UPGRADE ONLY. And the read me file says its the wrong RUU. But it is the same file from Tmobile I used when I first got the phone. But I will try again.
Are there any other suggestions?
You need to read the "how to flash" sticky.
I did. I am not any expert or anything but I believe the phone is unlocked already since I once had WM6 on my phone. The real issue I am having is that it wont boot past the splash screen after flashing.
And that is true when re following the steps in guide. After flashing to the button rom it will not boot past the splash screen.
Try another ROM.
Sounds like you need the "Wizard Love" rom. I dont have the link handy but I am sure someone else does.
Drunknasty said:
I did. I am not any expert or anything but I believe the phone is unlocked already since I once had WM6 on my phone. The real issue I am having is that it wont boot past the splash screen after flashing.
And that is true when re following the steps in guide. After flashing to the button rom it will not boot past the splash screen.
Click to expand...
Click to collapse
Already got it. Thanks I am trying to load it now. But the only thing is that the last time it failed and I can understand what the error says. I know the number is 300 but can read the language.
But I will let you guys know when this load completes.
Thanks again for all the assistance.
No worky worky. The load completed and then boots the splash screen shows and then stays there.
Any ideas?
Try to remove the battery and let it out for at least half an hour. Then put it back in and see what it does then.
I thought the same thing too. So when it got done last night, out of frustration, I removed the battery and left it there to wait on when I get off work today. I will report back on what happens.
Again I would like to thank you guys for helping me. I really do appreciate it!
STEP 1 install the original manufacturer ROM
T-mobile UK
http://www.tm-phonedownloads.com/download_manager_mda_vario.html
T-mobile US
http://www.t-mobile.com/wmupgrade/
Search for the original rom for any other
instructions on how to use the original rom can be found here
http://support.t-mobile.com/knowbase/root/public/tm23294.htm?&A2L.SERVICE=AboutUpgrading
Put it in the bootloader mode.. ( three color screens )
hope this helps..
cheers
Praneet
Ok I did that and it gave me ERROR 296: UPGRADE ONLY
Then it tells me that the NBF file cannot be used for my PDA Phone. Please get newer NBF file.
Is there any way I can get the Tmobile splash and IPL\SPL number back to original, it doesnt need to boot all the way into WCE but atleast show the same numbers and splash during boot up?
Or any other way to get this thing to work?
Thanks guys
BTW it is a HTC Wizard from T-mobile.
If you are getting an error 300 you need a newer rom update utility, and regardless if your phone is a G3 or G4 it needs to be unlocked before you flash any rom.. LOAD a OFFICIAL cingular ROM onto your device before going any further, then unlock your phone either via www.imei-check.com or through some of the tools offered here...
Which one should I down load from Cingular? Even though I have a Tmobile phone?
what ipl and spl are you using and what radio are you using. Just post all the numbers from the bootloader
As soon as I get home, I will post them.
Thanks
Ipl 1.01
Spl 3.08
Thanks
Drunknasty said:
Ipl 1.01
Spl 3.08
Thanks
Click to expand...
Click to collapse
uh oh. someone tell me if I'm wrong, but I think this is bad. it's the result of flashing a g4 with g3 or the other way around... keep searching, and good luck.
flash the original t-mobile rom. your phone doesn't appear to be unlocked. good luck

Flash without hardspl

I have an unusual problem with my oem att tilt running SPL-1.56.0000 (according to the bootloader screen).
The ROM is somehow corrupted in that it will not boot past the giant ATT logo and coordinates (?) screen. I have been having some trouble with the device, but this is a new occurrence not related to anything I did. I have never reflashed the ROM, and because it is in a current hosed state I cannot run hardspl on the device.
I have tried reloading many of the "ATT OEM" ROMs I can find, but they all return "Invalid ID" error the ROM uploader I believe because the versions don't match.
Is there any way to reflash the ROM and bootloader on the device without having first run hardspl? Am I SOL?
Thanks
RK
Did you try going to tri-color first then flashing a stock tilt rom?
Dude, I have the same problem...
I bought the tilt 2 weeks when I was in a business travel in the US and came back to Argentina... I'm kind of screwed about the warranty 'cause I don't think I'll go again so soon to the US...
Is there anybody who can help us with this?
The very diference is that (At the ATT start up Logo screen) the bottom line says D 1.57.00.00 instead of D 1.56.00.00.
Tried everything... soft reset, hard reset... and so on...
The thing is that at some point I think I can get to the phone in some way since if I turn on the phone keeping pressed the camera button and enter in the rom loader screen I can get comm to the phone using mtty (As pof explained to do for "Un-brick" the phone (In the case you got a bad flashing) in this thread...
So, please If anybody have any idea it would be great!
I still have a little hope, because it's like there is some kind of communication between the phone and the computer...
Thanks in advance to any help.
A.
both of you...
Check my sticky thread for reverting back to the stock tilt ROM and SPL...
all you really need from there is the Stock ATT ROM... download it!
Put your phone in Bootloader (shouldn't be too difficult by the sounds of it)
Install the stock ATT ROM.
If this doesn't work try extracting the downloaded ROM (using WinRAR or similar) then just run the ROMUpdateUtility.exe
Then you might want to consider installing HardSPL... the default download should work for the 1.56 guy. The 1.57 guy will need to download jwocky2001's whitescreen fix (check the stickies).
Good Luck!
I am at the tricolor screen and I have tried the instructions on your thread (thanks very much for making it so easy). However, it says invalid vendor ID after loading 1%; the device automatically reboots and reverts back to the ATT screen until I place it back into the tricolor bootloader again. I thought this was because the version I'm running is 1.56 and I could only find two original OEM ATT ROMs, neither was 1.56 and both failed.
BTW I couldn't do the part about hardspl and running the kaiser program on the device for obvious reasons, but I could get the kaiserruu program to recognize the device, another ROM and attempt to upload it.
Any other thoughts? Do I really need the exact same ATT OEM ROM as what is on the device or is something else wrong?
Thanks again
RK

I need some help BAD! My Tilt lost sound and black screen after boot

I was trying to follow the many different ways to unlock, Hard SPL, and flash a new ROM but this is just way over my head. I think I may have screwed up my phone. I've been reading for 4 hours and I'm just throughly confused (this was so much easier on th Artemis!). I downloaded the jumpSPL1.56-KAS, ran it from the phone (not the storage card). Then I ran Kaiser-HardSPL-3.56 and that seemed to work fine. Then I tried to run step 1 of the KaiserUnlocker and now it will only show me the AT&T boot screen and nothing else after that. What did I do wrong?
I'm trying to unlock the phone so I can use it on T-Mobile USA and flash a new ROM. I've flashed ROMS before but I just never realized how involved this process was on other devices.
And yes, I can get to the boot loader screen.
shawndh said:
I was trying to follow the many different ways to unlock, Hard SPL, and flash a new ROM but this is just way over my head. I think I may have screwed up my phone. I've been reading for 4 hours and I'm just throughly confused (this was so much easier on th Artemis!). I downloaded the jumpSPL1.56-KAS, ran it from the phone (not the storage card). Then I ran Kaiser-HardSPL-3.56 and that seemed to work fine. Then I tried to run step 1 of the KaiserUnlocker and now it will only show me the AT&T boot screen and nothing else after that. What did I do wrong?
I'm trying to unlock the phone so I can use it on T-Mobile USA and flash a new ROM. I've flashed ROMS before but I just never realized how involved this process was on other devices.
And yes, I can get to the boot loader screen.
Click to expand...
Click to collapse
Ick...this sounds like one of a couple of things...either you really screwed it up (btw, even "really screwed up" has been known to be fixable thanks to the super awesome folks here on XDA Devs) or it's a simple fix. My first suggestion would be to put it back into bootloader (just hold the usualy bootloader buttons and stick the stylus up in the Reset hole OR take the batter out and put it back in, your choice I think) and try rerunning everything EXCEPT the KasierUnlocker (btw, dont quote me but I would almost swear KaiserUnlocker needed a special radio flashed in order to properly work...you may wanna head back to that thread and check it out. I unlocked mine with it and I can about guarantee I had a special radio...) and see if it fixes anything OR find a compatible radio and reflash it (well, first off...get it into bootloader and tell us what the bootloader says on it)
Anyways, first things first would be to see what the bootloader is showing and then work from there. Sounds like a little bug so don't freak out too bad. If you think flashing these babies are hard then you really didnt try flashing G4 versions of the Wizard =P I totally bricked one because it was the pesky G4s and I didn't realize it at the time (complete newbness lol) So yeah, Kaiser's are a LOVELY change for me =] I've flashed mine countless times and loved it since the moment I got it! =D
But yeah, gimme info! =]
Did you use WM6.1 or WM6.0 to unlock the phone? Put in boot loader and flash orginal WM6.0 ROM as the other user suggested. You should be able to flash it if it is not a brick.
If it doesn't work you can use mtty to recover your phone, the needed information you'll find in the Kaiser Wiki.
Hope it helps
I just had this exact problem.
Use the EXE included in the tutorial to flash any windows 6.1 ROM from the bootloader via USB, and you will boot again.
HTCOmega said:
Ick...this sounds like one of a couple of things...either you really screwed it up (btw, even "really screwed up" has been known to be fixable thanks to the super awesome folks here on XDA Devs) or it's a simple fix. My first suggestion would be to put it back into bootloader (just hold the usualy bootloader buttons and stick the stylus up in the Reset hole OR take the batter out and put it back in, your choice I think) and try rerunning everything EXCEPT the KasierUnlocker (btw, dont quote me but I would almost swear KaiserUnlocker needed a special radio flashed in order to properly work...you may wanna head back to that thread and check it out. I unlocked mine with it and I can about guarantee I had a special radio...) and see if it fixes anything OR find a compatible radio and reflash it (well, first off...get it into bootloader and tell us what the bootloader says on it)
Anyways, first things first would be to see what the bootloader is showing and then work from there. Sounds like a little bug so don't freak out too bad. If you think flashing these babies are hard then you really didnt try flashing G4 versions of the Wizard =P I totally bricked one because it was the pesky G4s and I didn't realize it at the time (complete newbness lol) So yeah, Kaiser's are a LOVELY change for me =] I've flashed mine countless times and loved it since the moment I got it! =D
But yeah, gimme info! =]
Click to expand...
Click to collapse
I know. The crazy thing is that I've successfully flashed a G3 and a G4 Wizard and I still find this confusing.
When I go to the boot loader screen I have:
KAIS1*0
SPL-3.56.Hard
CPLD-8
When I reset the device normally I get:
R 1.27.12.11
G 22.45.88.07H
D 1.62.00.00
I didn't try to flash any other ROMS to unlock it. I just went with the hard SPL and then tried the Unlock tool. The phone is stock.
Thanx for the replys. I reflashed the original ROM and now it's working again. This is what I have now:
When I go to the boot loader screen I have:
KAIS1*0
SPL-3.56.Hard
CPLD-8
Now when I reset the device normally I get:
ROM version 1.62.502.0
Radio version 1.27.14.09
Protocal version is 22.45.88.07H
Device info:
Windows Mobil 6
CE OS 5.2.1622 (Build 18128.0.4.4)
Can I go strait to a SIM unlocker and then flash a new ROM?
Well you've got HardSPL 3.56 flashed to it.
Why do you need to sim unlock it? Sim unlocking is not neccesary to flash one of the many Roms avaliable for the Kaiser/Tilt.
Once it's got HardSPL flashed, you're free to flash any type of rom onto it
shawndh said:
I was trying to follow the many different ways to unlock, Hard SPL, and flash a new ROM but this is just way over my head. I think I may have screwed up my phone. I've been reading for 4 hours and I'm just throughly confused (this was so much easier on th Artemis!). I downloaded the jumpSPL1.56-KAS, ran it from the phone (not the storage card). Then I ran Kaiser-HardSPL-3.56 and that seemed to work fine. Then I tried to run step 1 of the KaiserUnlocker and now it will only show me the AT&T boot screen and nothing else after that. What did I do wrong?
I'm trying to unlock the phone so I can use it on T-Mobile USA and flash a new ROM. I've flashed ROMS before but I just never realized how involved this process was on other devices.
And yes, I can get to the boot loader screen.
Click to expand...
Click to collapse
A couple of things:
1) The Kaiser-Unlocker only works on 1.xx hardspl's, so you'll have to put one of those on first.
2) You do need to install the patched radio before you run it.
3) You'll need to flash a compatible radio afterward too, or else your device might not boot all the way.
4) Next time please post these questions in the thread for the unlocker you are using. It makes it much simpler for everyone.
stuff said:
Well you've got HardSPL 3.56 flashed to it.
Why do you need to sim unlock it? Sim unlocking is not neccesary to flash one of the many Roms avaliable for the Kaiser/Tilt.
Once it's got HardSPL flashed, you're free to flash any type of rom onto it
Click to expand...
Click to collapse
But HardSPL 3.56 doesn't SIM unlock the phone from what I understand. I need to use it with T-Mobile SIM. So I need to chenge to a 1.XX Hard SPL to do this?
So I guess I went wrong with flashing 3.56 first and not 1.1
Then I need to patch the radio
Run the unlocker
rinstall the radio
Then flash the ROM
Problem I have now is that I can't seem to go back down to a lower SPL version.
shawndh said:
But HardSPL 3.56 doesn't SIM unlock the phone from what I understand. I need to use it with T-Mobile SIM. So I need to chenge to a 1.XX Hard SPL to do this?
Click to expand...
Click to collapse
You need to read the instructions carefully, and ask questions in that thread. All the experts in unlocking will be there to help you.

Noob question about flashing (sorry, I DID read the stickies!)

Ok here goes. Be nice, I'm new...
I have a Stellar in front of me (or Kaiser, TyTynII etc) which has managed to get itself into Boot Loader. I'm usually pretty good at getting these out of it but this one has me stumped, and I'm hoping someone may be able to give me some suggestions, or confirm my suspicions that it is kaput.
It's in Serial mode at the moment, showing
KAIS130
SPL-1.82.0000
CPLD-8
on the top of the screen.
So I plugged it into the computer and it nicely popped into USB mode which then let me flash it, using the file: RUU_Kaiser_O2_UK_1.82.206.1_radio_sign_22.45.88.07_1.27.12.32_Ship
This appeared to take, started the process, splash screen loaded, windows mobile loaded OK and for all intents and purposes was back at the factory reset (which is what I wanted). HOWEVER.....when I performed a soft reset it went back into Boot Loader and I'm now back at square one.
Any ideas? I can't install any homebrew ROMs on this, it HAS to be the standard ROM for reasons I'm not at liberty to post here (don't worry nothing illegal is going on, suffice to say, I shouldn't really be here!)
I have at least 2 others that are doing similar as well and would like to get these fixed also. All help/comments gratefully received and I apologise again if this is covered somewhere else.
It seems you have not done any SPL hard flashing yet.
Did you really read the Flashing for Noob sticky ? It's there .. first you need to do hard SPL, SIM/CID Unlock, then only you can change your ROM to anything.
Please go back and re-read.
Sorry. Will this do anything bad to the device, only I've never done anything like that before, I've just run the ROM flash file. I've never had to do anything like you suggested before. It needs to be put back to factory as it is going to get allocated to someone - which means I then have to install a clone over the top of this.....sorry if I'm being thick. I did read the document you suggested but that resulted in me getting more confused.
If this is not the right place for me to be, please feel free to close this thread and I'll keep looking elsewhere. Cheers.
Hi,
First of all: what do you want to do? Read this to clarify your intention
Take your time, read through the WIKI first.
After that, if you still want to flash, go to the Noob sticky.
If you don't have the passion, I'd suggest just use the phone as from factory. Reading the Wiki still will give you insight and many good tips/tricks without flashing.
Edit to addI apologize.
After re-reading again, it seems that what you're trying to do is reviving the dead Kaiser. From the SPL version, it's not yet 6.1. You can check out here to see any other official ROM matches, which what you currently use seemed to be correct.
Mod, please merge this with Kaiser stuck at Bootloader thread ..
Good luck.
Edit 2
It seems that when you did a soft reset (by pushing at the small hole using stylus?), the other two buttons (camera + power) are still pressed (or due to hardware, kept being pressed), thus resulting in boot loader displayed again?
Well that's why I couldn't work out why I couldn't get the ROM to stay.....this has never happened before! So yes, I am trying to revive a seemingly busted Kaiser. The customer handed it to me in Boot Loader mode. Usually running the RUU fixes this and we can then go about rebuilding it. However in this case it really doesn't want the factory ROM but I need it to! I can quite easily get it into USB mode and flash it by running the .exe file on my desktop - but then that's about all I can do. I can't give it back to the customer as the next time he performs a soft reset or switches it off, it'll be back in Boot Loader...ARGH!
Oh, and apology accepted!
And another thing, I just tried running the exe file again and got as far as the screen alignment and the poxy thing just locked....cue soft reset and back to Boot Loader. Me not happy.
Edit: A quick check of the Hardware and all the buttons appear to be OK - nothing looks like it's stuck down
If you want to take the looooong road, perhaps you can do flashing Hard SPL, unlock SIM/CID and then flashing any other ROM/Radio. Once you get a stable working device, you can flash back the OEM using this method
I'm not sure if this custom RUU can help: http://forum.xda-developers.com/showthread.php?t=334890
I haven't tried that, so it's just an idea for now.
Thread closed.
If you are still having problems with the bootloader check out my sticky.
If you need help with the flashing process check out mskip's sticky.
Only create a new thread for new issues that have not been discussed before.
Good luck
Thanks
Dave
OK, I too skim read (I read a lotta threads ).
PDA-Princess
I've sent you a PM.
Dave

Categories

Resources