Related
Just ordered and installed Realook screen protectors and I couldn't be more pleased. I have used other screen protection from Zagg and Sprint and I did not like them nearly as much. I will do my best to describe what its like but you really need to see it in person.
Feel:
The material is a firm plastic that when applied feels nearly the same as the bare glass. I did not like Zagg because it felt soft and textured like an orange peel. This stuff is 95% the same feel as glass and I waited 20 days before installing it, so I have a good level of comparison.
Look:
Clear as glass. I have not yet tested what effects it has on glare, but there is no noticeable difference indoors. Also it is ready to go 30 seconds after installing. All you need to do is push out the large air bubbles. It doesn't take 1 or 2 days to settle like some other protectors. Other people in this thread reported a rainbow reflection in the sun light when the screen is off.
Installation:
Before I started I ran the shower on hot to fill the bathroom with some steam to settle the dust. There is nothing that will bother me more than a single spec of dust under a screen protector, I will obsess about it to no end. Due to my rough and dry hands I am a dust machine and I have never failed to get at least 1 piece of dust under every screen protector I have installed. This time was no different. I mis-aligned the screen on installation and had to peel it back, when I did 1 spec of dust planted itself. I used a piece of tape they include in the box to peel back the screen, and another piece of tape to pull off the dust and it was clean. I am sooo happy about this point. Other protectors I used with adhesive would grab onto dust and never let go. Since it does not use adhesive so it is easy to put on and peel back off if you made a mistake.
The Bad:
Back button less responsive. It will still work on the first touch every time, but you do need to touch a little harder than before.
Box Includes:
2 screen protectors.
1 Wet wipe
1 Plastic card to push out air
2 pieces of tape(if needed)
1 microfiber cloth(to clean the screen before and after installation)
Sorry for the slightly blurry photos. Taken with another Epic4G and it doesn't like to focus on close ups.
$11 at Amazon
does it make the screen fuzy?
Perfectly clear. I wish I had a better camera to show it.
edit: I just discovered macro mode in the camera settings. I will post more photos soon.
Returned the Sprint speckled ones that was degrading display quality to the local Sprint store and am awaiting delivering of Realook for both Samsung Epic and Panasonic GF1 camera. Realook sounds like the best option and value out right now for the Epic until Steinheil Ultra Oleophobic is made available for comparison.
a holes wouldnt take mine back
+1 for Realook! Best screen protector i have used. Same experience as Pops.
I also went to Realook after Skinomi. Love Realook! Slick, smooth feel like the original glass. Relatively easy to apply. No screen degradation. Wonderful, all around.
does no opening for cam hinder it?
Anyone want to trade their spare ReaLook for a pair of PhantomSkinz screens?
I also have the Realook on my phone and it's absolutely great.
But since no one actually pointed out the cons, I'll try to list a few:
- It's not a PERFECT fit so you'll find gaps on all four sides. I'm concerned that dust may eventually get stuck in those gaps.
- I don't exactly remember how the bare screen was now that I have the Realook on, but I think the Realook makes the screen a little more "reflective".
- Under artificial lights (esp. fluorescents), you'll notice the interference patterns like straight rainbows. Hard to explain but people with screen protectors on any phone may have seen them before.
- The capacitive buttons become less responsive meaning that you'll have to push them harder.
churro7 said:
does no opening for cam hinder it?
Click to expand...
Click to collapse
Doesn't seem to. It is pretty optically clear. With 640x480, you probably wouldn't notice if there was any difference anyway.
tonysohn said:
I also have the Realook on my phone and it's absolutely great.
But since no one actually pointed out the cons, I'll try to list a few:
- It's not a PERFECT fit so you'll find gaps on all four sides. I'm concerned that dust may eventually get stuck in those gaps.
- I don't exactly remember how the bare screen was now that I have the Realook on, but I think the Realook makes the screen a little more "reflective".
- Under artificial lights (esp. fluorescents), you'll notice the interference patterns like straight rainbows. Hard to explain but people with screen protectors on any phone may have seen them before.
- The capacitive buttons become less responsive meaning that you'll have to push them harder.
Click to expand...
Click to collapse
I agree with all of those. I only have a gap on the bottom, though. Left and right seem to be exact.
I see the rainbow effect but it doesn't seem to cause any problem for me. I really don't notice it unless the display is off.
I do have the less responsive buttons, especially the back button. I'm wondering if I could slice off the bottom centimeter of the protector smoothly enough to make it worth trying.
Jason
I like it, but...
It's harder to clean than the Gorilla Glass of the Epic. It also has more friction than the Gorilla Glass. Your fingers won't glide across it as effortlessly. Finally, it has slightly rough edges that you can feel.
I should sell my unused RL screen for 5 bucks or something. Do people typically do that with their unused protectors?
Just ordered mine from amazon after reading this thread, i hope it is as good as you say it is. I have used Zagg a few times before, and Skinomi twice, and BodyGuardz on my nexus one. my favorite was BodyGuardz, but for 10 bucks i think it is worth trying this one. ill give feedback when it gets here in a few days.
If anyone wants another (good) opinion, here's a review from ppcgeeks.
I posted my review on realook a while back on ppcgeeks. Best protector ever IMO. http://forum.ppcgeeks.com/sprint-ep...king-screen-protector-tips-4.html#post1942030
Post #34
Sent from my SPH-D700 using XDA App
i use skinomi very nice and slick
I might give real look another chance but I used one on my touch pro 2 for a few months it looks and feels absolutely great however when i took it off today there was definitely some residue left behind. Swiping on the screen was not as smooth as when i first bought it. I just got my epic today and blew the installation of the clarivue protector. I don't think reallook has no adhesive, I think it has some adhesive so before I give them a try again i am gonna try boxwave and clarivue 1 more time.
the best protector IMO
I agree that the Realook protectors are the best. I installed mine a week ago and i'm really liking it. The look is awesome, the fit is perfect and it doesn't really have much more drag then the naked glass. The one issue is the fingerprints and oil residue. I can tell you that the phone is much more difficult to keep clean with the Realook, but that's not big of a deal. I used to just use my shirt or pants to wipe the phone clean, and now i have to use a microfiber. Even then it takes about two to three times the effort to get the oils off. I would still recommend this product.
I just got my real look in today (ordered thursday night) and i have a 10% off coupon code if anyone plans on getting one via amazon before the 30th.. pm me if anyone wants the code...
ordered from same link the OP posted $11 shipped so coupon will drop a buck off.. nothing much but I figured id throw it up here
UPDATE:the coupon is spoken for.
Ok i need to first say Pops_G you rock for informing me about this screen protector, and your method with the shower was genius, wish i did that when i installed all the other screen protectors in my past. On to my experience...
I just got the Realook Screen protector today, and i previously stated in a prior reply, i have tried zagg invisible shields, BodyGuardz ( OLD FAVORITE ) and Skinomi. The application of the Realook Screen protector was hands down, the Easiest ever, i didn't think it could go that fast. And in terms of how it looks and feels, I could not believe my eyes. You seriously cannot tell when looking at the screen that there is a protector on there. Zagg, Bodyguardz, Skinomi all have, in some regard, no matter how small, a orange peel effect, where there are small ripples in the screen from the water that is used in the installation process, they go away in time, but it is slightly noticeable. They also feel rubbery and take away from the graceful movements of the screen. Plus you have to turn off the phone, pull batter, use a water/soap spray mixture, worry about air bubbles, let it dry 24 to 48 hours, and wake a week plus for the solvent to evaporate. I had this Realook applied in 5 minutes, it would of been less, but i was super anal about making sure not a spec of dust was on the screen. lol.
Now this is just my first impression, after a hour or so of use. It is plastic which makes it feel very much like the original screen, although im sure that will allow the screen protector to scratch, unlike zagg, bodyguardz, and skinomis rubber film where they wont, unless you really try. And also it does show the finger oils more than the actual glass does. I am ok with this becasue that is the purpose of the protector, to get scratched and not the actual screen, Plus i have a backup because 2 came in the pack. GREAT DEAL. Second, i only see this screen protector working for phones that have a completely flat screen and have some sort of small lip around the phone. For Example: I dont think it would work best on a palm pre, which has no lip, and then it could be more easily peeled off down the line. But for the Epic 4g... Seriously im in love.
Thanks again Pops_G
I've been looking all over the internet and I've been unable to find anything that looks like it would keep my greasy ass hands from messing up my touchpad screen. Does anyone else have any ideas?
Sent from my HP TouchDroid
I would like to know too. I hate having to use my shirt to scrub the screen clean. lol. But I'm sure ANY screen protector is better than having none.
I've read that rainx works for what you are trying to do.
Sent from my PG86100 using XDA
mrtomaso said:
I've read that rainx works for what you are trying to do.
Sent from my PG86100 using XDA
Click to expand...
Click to collapse
Just looked that up. I dont know if I'm comfortable with putting that stuff on my TouchPad. Even though others have said it works well.
Yeah I was looking for something more like the matte plastic skin I have on my razr
Rootin' and fastbootin' on my Droid razr
Zagg Skinomi BodyArmorz,
cdzo72 said:
Zagg Skinomi BodyArmorz,
Click to expand...
Click to collapse
I was about to suggest military shield, but I think I'm going to try skinomi because its half the price with decent reviews (via amazon). I have the military shield on my phone screen, and it is freaking awesome. Crystal clear, NEVER scratches so it seems, fairly resistant to fingerprints, and it has a nice, natural feel to it. Zagg on my cousins vibrant felt waaaaaay too sticky/tacky. Just not natural at all. Will let y'all know when I order/test the skinomi protector.
dung8604 said:
I was about to suggest military shield, but I think I'm going to try skinomi because its half the price with decent reviews (via amazon). I have the military shield on my phone screen, and it is freaking awesome. Crystal clear, NEVER scratches so it seems, fairly resistant to fingerprints, and it has a nice, natural feel to it. Zagg on my cousins vibrant felt waaaaaay too sticky/tacky. Just not natural at all. Will let y'all know when I order/test the skinomi protector.
Click to expand...
Click to collapse
Skinomi is the same tacky crap as zagg.
I find just getting any "Matte" screen protector works wonders. It scatters light, and doesn't seem to attract fingerprints the way those other shiny guards do. I got one on Ebay for $3. Just type in Matte screen protector touchpad for a cheap solution.
Sw339 said:
I find just getting any "Matte" screen protector works wonders. It scatters light, and doesn't seem to attract fingerprints the way those other shiny guards do. I got one on Ebay for $3. Just type in Matte screen protector touchpad for a cheap solution.
Click to expand...
Click to collapse
Any tips on best approach to apply these where you get no bubbles and it lines up right? I suck at doing these for phones.
famewolf said:
Any tips on best approach to apply these where you get no bubbles and it lines up right? I suck at doing these for phones.
Click to expand...
Click to collapse
Well its pretty easy, you just need a sticky tape and a good eye.
You need to do it in a clean room, and obviously you need to clean the screen first.
If you failed at the first attempt, just peel off and try again, no harm on doing that.
The easiest way to align it is to aim for the camera hole and the home button, just make sure they are centered when u aim it.
If you have bubbles after application, this is most probably caused by dust (or just bad quality screen protector) if it is a dust, just use the sticky tape to remove the dust. The sticky tape will not leave any mark on your screen nor the screen protector.
Hope this tips will help
Putting it on in a steamy bathroom also helps keep the dust out of the air. On your first attempt, try to peel it off of the backing as you apply it, pushing trapped air out as you go. It gets a bit trickier when you have to handle the whole thing peeled off.
Okay, so after using the skinomi skin for about a week now, I have to say I like it. One of the reasons I got my stylus was because I hated fingerprint smudges on the screen, and with the skinomi, it is hard to see any smudges after multiple uses. May ditch my stylus now, who knows.
Anyways, a couple things to note:
1) as another user stated, put the skinomi on after a hot shower with the door closed. You want the mirrors good and steamed up
2) line up the home button first. My skinomi is a little off and so its closer to one edge of the screen than the other. No biggie, really, just full disclosure
3) don't worry about the camera hole so much. For one, camera doesn't work on cm9 anyways. For two, even if it seems like the skinomi is a little bit over the lens, I don't think its a big enough of a deal. You could line it up perfectly on the camera, but you run the risk of your home button being overlapped by some of the skin
4) while squeegeeing, use the included cloth to wipe up any solution that gets pushed to the edges. Maybe not necessary, but I did anyways
5) once you are done, IT WILL LOOK LIKE THE CRAPPIEST SKIN/SCREEN PROTECTOR EVER. Again, don't worry. After 2 or 3 days, it will should look great.
I would post pics, but what's the point? If anyone wants, I guess I could. anyways, for about 7 bucks, I would definitely recommend the skinomi protector. It does not feel all tacky like the zagg stuff, its actually pretty nice.
http://www.spigen.com/new-product/spigen-sgp-htc-one-x-screen-protector-steinheil-ultra-series.html
Two choice,
1.Ultra Fine
2.Ultra oleophobic
which one is batter?
thanks
I don't use them ...
farwish said:
http://www.spigen.com/new-product/spigen-sgp-htc-one-x-screen-protector-steinheil-ultra-series.html
Two choice,
1.Ultra Fine
2.Ultra oleophobic
which one is batter?
thanks
Click to expand...
Click to collapse
I don't use screen protectors on any phone with gorilla glass. It's basically unnecessary. It's virtually impossible to scratch the screen unless you really make the effort.
Remember, it's glass. Why not take a fork and try your best to scratch a window made of glass. It can't be done.
Peter
I get where you're coming from Peter but just because you don't want screen protectors doesn't mean you shouldn't try and contribute to someone who does. My Captivate had gorilla glass and it has plenty of scratches just because of grit. It happens, no matter what.
However, Ultra Fine is just going to be super clear, and Ultra Oleophobic will do it's best to keep finger prints from showing/building up.
PeterHTC said:
I don't use screen protectors on any phone with gorilla glass. It's basically unnecessary. It's virtually impossible to scratch the screen unless you really make the effort.
Remember, it's glass. Why not take a fork and try your best to scratch a window made of glass. It can't be done.
Peter
Click to expand...
Click to collapse
I used to use screen protectors all the time until my nexus one, had that phone for 2 years with plenty of abuse, including at least 4 good drops, one in a cement underground parking floor with a small kick and slide for good measure, my hart stooped on that one! still not a scratch on that phone.
so i did not get one for my galaxy nexus, dropped it once while kneeling on the flatbed of a tow truck, not a very far drop at all, and got 1 nasty looking scratch and 3 minor ones! ruined my day, week even i still look at it and get sad.
i have no idea what glass is in the galaxy nexus, but to me it was very easy to scratch, if i can find a screen protector for the xl that is not annoying to look at i will probable start using one.
just sayin
grinmaul said:
I used to use screen protectors all the time until my nexus one, had that phone for 2 years with plenty of abuse, including at least 4 good drops, one in a cement underground parking floor with a small kick and slide for good measure, my hart stooped on that one! still not a scratch on that phone.
so i did not get one for my galaxy nexus, dropped it once while kneeling on the flatbed of a tow truck, not a very far drop at all, and got 1 nasty looking scratch and 3 minor ones! ruined my day, week even i still look at it and get sad.
i have no idea what glass is in the galaxy nexus, but to me it was very easy to scratch, if i can find a screen protector for the xl that is not annoying to look at i will probable start using one.
just sayin
Click to expand...
Click to collapse
ditto here. i noticed the other day i had a tiny scratch up near the ear piece of my GNex. mine has never been dropped so not sure where i got it from but it was the first phone i went completely naked with. won't make that mistake again. def getting a screen protector and most likely the SGP Oleo.
PeterHTC said:
I don't use screen protectors on any phone with gorilla glass. It's basically unnecessary. It's virtually impossible to scratch the screen unless you really make the effort.
Remember, it's glass. Why not take a fork and try your best to scratch a window made of glass. It can't be done.
Peter
Click to expand...
Click to collapse
Any minute particle of sand will scratch gorilla glass without exception.
You are 1) being irresponsible, 2) promoting those irresponsible ideas to others.
Gorilla glass is not scratch proof by any means. It has barely higher hardness compared to normal borosilicate glass, and it's far softer than sand.
nabbed said:
Any minute particle of sand will scratch gorilla glass without exception.
You are 1) being irresponsible, 2) promoting those irresponsible ideas to others.
Gorilla glass is not scratch proof by any means. It has barely higher hardness compared to normal borosilicate glass, and it's far softer than sand.
Click to expand...
Click to collapse
Calling someone irresponsible is a bit harsh, no? It's a difference in philosophy. Many people don't believe in screen protectors. I live in sandy Florida and I've been just fine. My friend on the other hand scars his screens.
vioalas said:
Calling someone irresponsible is a bit harsh, no? It's a difference in philosophy.
Click to expand...
Click to collapse
True, its all a matter of personal choice. There is a tiny change in the feel when you use a screen protector, and some don't like it. If a person chooses not to use a screen protector, and willing to live with scratches (if they do occur) then that's totally up to them. If someone scratches the screen, and claims the GG as "defective", then I suppose that is irresponsible (as there is not advertised guarantee against scratches).
That said, GG is far from impossible to scratch. Its intended to be scratch resistant, but can still be scratched (and even cracked). Coming from another device with GG, I can tell you that I have seen many cases of people that got scratches after normal use, and no obvious instances of abuse, drops, etc. And if you remember when the iPhone first came out with GG, there were also plenty of instances of people getting scratches almost immediately after release. On the other hand, plenty of people have had good luck with no scratches on GG, even after serious drops, etc. A bit of luck is certainly at play. But if you don't use a screen protector, and end up with a scratch, you can't easily undo it. IMO, its better to use a protector, and not have to worry about such regret.
A good quality screen protector has very minimal change in feel (although there is a very slight difference) no change in look, and will also attract fingerprints and smudges a bit less than the "naked" screen. Cheap ones are not worthwhile, and often look and feel much worse, and can start peeling off easily. Some people that are against protectors, may be due to experience with a cheap one. Bodguardz and Skinomi are quality ones that I have used, and there are plenty of other good ones.
Hey guys, this topic was started to answer a mans question about the difference between two types of screen protectors not borosilicate and gorilla glass. I feel that this topic should be A. closed if nothing good is to be added, or B. put back on topic for the benefit of OP.
okay, i'll knock his question out really quick...
the Ultra Fine (Anti-fingerprint) is a matte type of screen protector. because it is matte, it's going to degrade the colors a little bit. they won't be as vibrant as without this particular protector.
the Ultra Oleo is a clear screen protector. approx 100% of the colors will still come through as if you didn't have this one on. it's made to be resistant to fingerprints, though the Ultra Fine is going to do a far better job of keeping fingerprints off.
so, you have to ask yourself this...
do you mind losing some of the pop from the colors to keep fingerprints off of your screen, or would you rather see your display like there was nothing on it but have more visible fingerprints?
i always go with the clear ones. i had a matte protector on an old iPhone (3G?) and didn't like it. haven't had a matte one since.
Its a bit hidden, but it says on the product webpage FAQs:
What are the differences between the Steinheil Ultra Fine and Ultra Oleophobic Screen Protectors?
All of our screen protectors are Japanese made, enhanced optical hard films. The Ultra Oleophobic screen protectors is a clear type where it absolutely doesn't affect the screen image quality. Ultra Oleophobic has an oil resistant coating to resist oil and other contaminants. Ultra Fine screen protector is matte type hard film which resists against fingerprints and smudges, but it is less clear compared to other Steinheil screen protectors.
So it seems the main difference is that the Oleophobic seems to be the "regular flavor", while Ultra Fine has a matte finish (and $2 more). What is "best" for matte versus regular finish is typically a matter of preference. Matte tends to give less glare (and might be helpful outdoors in sunlight) but tend to be less clear, and may have a tackier feel or even textured feel (not sure if the different feel is true for this particular brand). Hopefully somebody with specific experience with this brand can give an opinion.
Some people (like the previous reply) don't like matte; while I've seen others that seek it out.
Question about these screen protectors, if anybody has used them, can you post a picture? All the protectors I've seen for the One X so far look bad because of the way the screen is shaped, they curl up on the edges.
http://forum.xda-developers.com/showpost.php?p=25084817&postcount=69
there ya go vioalas, that's the skinomi protector, and it's a wet app so it's just like, the best fit possible. Hope that helped!
vioalas said:
Question about these screen protectors, if anybody has used them, can you post a picture? All the protectors I've seen for the One X so far look bad because of the way the screen is shaped, they curl up on the edges.
Click to expand...
Click to collapse
I can't do a pic (at work) but I have only used the Ultra Oleophobic on my past two devices, and it is the closest thing to the feeling of the glass out there. There is still a tiny bit of drag that isn't present on the screen, but really is barely noticeable.
Because these are dry application protectors, they can't go all the way to the lateral edges of the One X's screen, apparently it has a slight taper/roll and the SP would lift. My Galaxy Nexus (with the contoured screen) leaves about 2mm all the way around, and that was very clear in SGP's pics on their website. Their pics for the one X show less of a gap and the gap is mostly on the sides, so I think it will look better than it does on the Galaxy Nexus...
s.m.knipe said:
I can't do a pic (at work) but I have only used the Ultra Oleophobic on my past two devices, and it is the closest thing to the feeling of the glass out there. There is still a tiny bit of drag that isn't present on the screen, but really is barely noticeable.
Because these are dry application protectors, they can't go all the way to the lateral edges of the One X's screen, apparently it has a slight taper/roll and the SP would lift. My Galaxy Nexus (with the contoured screen) leaves about 2mm all the way around, and that was very clear in SGP's pics on their website. Their pics for the one X show less of a gap and the gap is mostly on the sides, so I think it will look better than it does on the Galaxy Nexus...
Click to expand...
Click to collapse
thanks for input on the actual fit with dry protectors. i thought the glass was flat on the One X if true, the only way to get a complete fit would be wet applications. guess i'll finally have to use a wet application.
mrvirginia said:
thanks for input on the actual fit with dry protectors. i thought the glass was flat on the One X if true, the only way to get a complete fit would be wet applications. guess i'll finally have to use a wet application.
Click to expand...
Click to collapse
No, I think it is just the gradual roll the edges of the screen do to meet the plastic. the screen itself is flat, and the roll appears to only be on the left and right sides. I think even wet application ones would have trouble with it... look at some of the pics that depict the phone in profile; the part of the screen glass that protrudes above the plastic (best noticed in the white model) seems to have a radius (or "roll") to it.
Any other places to get these now that fit.. Dry and not $16
s.m.knipe said:
No, I think it is just the gradual roll the edges of the screen do to meet the plastic. the screen itself is flat, and the roll appears to only be on the left and right sides. I think even wet application ones would have trouble with it... look at some of the pics that depict the phone in profile; the part of the screen glass that protrudes above the plastic (best noticed in the white model) seems to have a radius (or "roll") to it.
Click to expand...
Click to collapse
ahh gotcha. well so far it sounds like the skinomi is the way to go. i was never a fan of that orange peel effect but if that's the best then that's what i'll have to go with.
mrvirginia said:
guess i'll finally have to use a wet application.
Click to expand...
Click to collapse
The wet apply protectors are not as scary as they would seem. Your lightly spray the application fluid onto the protector, and its really not enough to penetrate into any cracks. And even if it does, its not enough to short circuit anything. Have the device powered off, and let it dry for the recommended time, and you will be fine.
I used dry apply protectors for my first couple smartphone, as I was also a bit wary of the wet apply method. But when I finally went the wet apply method, I found it easier to install. The wet method give you some time to get the protector perfectly in place before the protector adheres.
---------- Post added at 06:15 PM ---------- Previous post was at 06:13 PM ----------
mrvirginia said:
ahh gotcha. well so far it sounds like the skinomi is the way to go. i was never a fan of that orange peel effect but if that's the best then that's what i'll have to go with.
Click to expand...
Click to collapse
I have a Skinomi installed on my Flyer tablet, and am quite pleased with it. its very smooth with no noticeable orange peel effect.
I guess I'll do the wet application. Would you guys trust the radioshacks/bestbuys that offer to apply it for you?
When I first got my first A2, the rep at best buy put on the screen protector before I left the store... (keep in mind that this is my first "smart" phone of any kind, let alone android) ..so, I had never really known it without a screen guard/shield/protector until I got my 2nd A2 (and, subsequently 3rd).
The 2nd A2 I knew was temporary because of a dead pixel in the center of the screen (and other signs of refurbishment), so I never bothered putting on a screen guard. And with my 3rd A2 and I still haven't put one on - I have a brand new Zagg Invisible Shield just laying there, but it been over 2 months... And, I gotta say I like it much better.
Now this can all depend on the shield you use, but without a shield, the touch seems more responsive, the screen crisper, it's easier to clean...
I have a nice case that is raised a bit on the topside edges to help protect, and I never put anything else in the same pocket as my phone...
I know it's risky, but don't we have Corning Gorilla Glass already? Can you scratch that? And I do eventually have a contract upgrade coming anyway..
Thoughts? Preferences? Keep your minds out of the gutters..
I had a screen protector when I first bought the phone, and I got annoyed with it. The screen was dimmer, but the screen was less prone to finger prints. I still have it as it's reusable, but I left it in the car in the Florida heat, so the layers of it are peeling off. My screen also jumps and stutters when it's plugged in and fully charged to 100%. I should probably buy another one to preserve the screen seeing as how I don't upgrade until May.
alteredlikeness said:
I have a nice case that is raised a bit on the topside edges to help protect, and I never put anything else in the same pocket as my phone...
I know it's risky, but don't we have Corning Gorilla Glass already? Can you scratch that? And I do eventually have a contract upgrade coming anyway..
Thoughts? Preferences? Keep your minds out of the gutters..
Click to expand...
Click to collapse
I have to agree with you. I personally was super paranoid about scratching my screen and so I put shields from various companies on my screen to help protect it. The screen guard got dirty and so I took it off, and I love not having the screen guard on because of the reasons you stated.
I am pretty sure our phone comes with gorilla glass, but it isn't invincible. I have a scratch on my screen but it isn't noticeable when using the phone just when the screen is off. But I guess just keep it safe in a pocket that you don't have anything in and don't have sand chillin' in your pocket.
I've had this phone for almost a year and I didn't start using a screen protector until a couple of months ago. For some reason the screen on this phone scratches easier than my Captivate. I keep them in my pocket but the Atrix 2 has accumulated quite a few small scratches near the bottom of the screen and around the buttons.
I would rather not use one, but I would like this phone to last a while, even as a back up. I've tried several protectors and I've settled on the Great Shield clear protectors. You can get 3 for $7.99 on Amazon and they install easy and are pretty durable. You can also take them off, clean them and reinstall them without losing any adhesive properties.
i had a anti-glare screen guard which i used for 6months and one day due to some expt i was doing on my phone with skins it got off. havent put one back, have just one tiny 1mm scratch which is visible only if you look at it tangentially. have to say the colors look more vibrant and the touch is more responsive (might be due to OC and cm10).
Anyways, i have a case with raised edges, same as altered described, and i take extra care of my phone now. but since im keeping this phone for another year n a half atleast, will definitely get a new screen guard, (maybe one without the anti-glare effect, if i find one) cause gorilla glass Is prone to scratches.
Real men dont use protection...
Stay classy.
Initially I didnt use any "protection" LOL, but had two tiny scratches on the screen. Yes, it does catch scratches easily compared my previous devices, I tried these 1. Amzer anti-glare, will be good for 1/2 months then you will hate it, 2. Amzer Mirror Screenguard, gave me migraine (literally!) 3. Right now having Xtremeguard on it and like it.
There are basically two reasons why I get the screen protectors, to protect the screen obviously and the screen without protector is too slick for my liking, that's just my opinion.
My first A2 went from release day to this September when it bricked and was replaced. In that time frame i had only acquired 2 micro scratches never had a screen protector on it nor do I have one on my replacement. Also the glass is coated it's that coating that is scratch resistant. Watch this
http://www.xda-developers.com/xda-t...ass-drops-tests-composition-xda-developer-tv/
I have a serious thing against screen protectors and cases. I prefer my phone to be naked.
Screen protectors, no matter what you people say, make the screen worse in some way. The display is made to work well alone. They just all suck, and if you ever want it off, in a lot of cases, god help you, especially with self adhesive ones. They do however help prevent scratches, because you will just scratch the screen protector instead of the screen, so if that is important, you may want to consider it.
Cases, now this is just opinion. There is no doubt that they help prevent your phone from breaking, I just absolutely hate them. I don't like to bulk up my phone and make it ugly.
All that said, I take very good care of my phone. I have never dropped it, and I doubt I will, so there is no need for a case if you are careful.
P.S. yeah, gorilla glass is a joke, it still scratches. Just has a slightly higher hardness, and wont break as easy, but coins or keys will still do their job the same.
souljaboy said:
Real men dont use protection...
Stay classy.
Click to expand...
Click to collapse
Priceless!
Sent from my MB865 using xda app-developers app
First up I feel like a dunce picking up that Skinomi worth 7 green skins sucks bad bad. Totally not recommended.
Gorilla glass is in iteration 2 of implementation so that speaks for itself about our ver 1. Plus there is no Oleophobic coating on our device. I invested a massive 20 + $ greenbacks on Otterbox and though no complaints with usability it sure makes the phone bulky and downright fugly. None of the screen guards last more than three months until you need to put a new one.
In India, given the extreme dusty atmosphere in cities, a small two hour ride in public transport coats the phone with dust. Otterbox covers the all ports with covers so that's good. In my opinion just a slip in/out elegant pouch is the best option. Screenguard I reckon is required. Wish 3M made the privacy screen protector for Atrix 2.
So after reading a bit on lots of different threads here and many other boards, I decided to pick up a couple of the LUVVITT Tempered Glass screen protectors.
I ordered from Amazon and got them for $10 each and free shipping (Prime)
I gotta say, it was the easiest install I have ever done. I started off with the hinge method but I used painters tape and it fell off and I just lined everything up and pushed down in the middle and watched the self adhesive. It went on VERY easy. I did this in a kitchen, (not in the bathroom with hot shower on for the steam) and I didn't get a single piece of lint on either of the installs.
Mine were cut essentially perfect. Cut outs were right on and everything went together pretty much perfectly. As a note, there were a few tiny bubbles in certain areas. I thought at first it was dust but pushed lightly down and it would disappear. Over the next 24 hours they vanished and the protector is now smooth as glass.
I do notice that it does seem to get smudges and some fingerprints, but with a quick swipe of a microfiber cloth (included) or an Oakley glass bag (which I always have on me) they disappear.
This really is a great buy over the glass that costs 2-3 times a much. I recommend this product if you are looking for a screen protector and want more but don't want to pay $30 for it. This is pretty dang good, as good as the ZAGG that is on my buddies phone. We compared them and you cant tell the difference at all.
Bought them here:
http://www.amazon.com/gp/product/B00IKRHCCY/ref=oh_details_o02_s00_i00?ie=UTF8&psc=1
mortymouse said:
So after reading a bit on lots of different threads here and many other boards, I decided to pick up a couple of the LUVVITT Tempered Glass screen protectors.
I ordered from Amazon and got them for $10 each and free shipping (Prime)
I gotta say, it was the easiest install I have ever done. I started off with the hinge method but I used painters tape and it fell off and I just lined everything up and pushed down in the middle and watched the self adhesive. It went on VERY easy. I did this in a kitchen, (not in the bathroom with hot shower on for the steam) and I didn't get a single piece of lint on either of the installs.
Mine were cut essentially perfect. Cut outs were right on and everything went together pretty much perfectly. As a note, there were a few tiny bubbles in certain areas. I thought at first it was dust but pushed lightly down and it would disappear. Over the next 24 hours they vanished and the protector is now smooth as glass.
I do notice that it does seem to get smudges and some fingerprints, but with a quick swipe of a microfiber cloth (included) or an Oakley glass bag (which I always have on me) they disappear.
This really is a great buy over the glass that costs 2-3 times a much. I recommend this product if you are looking for a screen protector and want more but don't want to pay $30 for it. This is pretty dang good, as good as the ZAGG that is on my buddies phone. We compared them and you cant tell the difference at all.
Bought them here:
http://www.amazon.com/gp/product/B00IKRHCCY/ref=oh_details_o02_s00_i00?ie=UTF8&psc=1
Click to expand...
Click to collapse
Appreciate the input, I was thinking about picking this up. I know mime ghost are top of the line but also don't want to spend a fortune on a screen protector. Will pick this up
Isn't 9H hardness a little bit too high ? i mean yeah it's gonna be very scratch resistant but it will break very easily too...
How easy/obstructive is the home button cutout? I am curious if you can use the fingerprint sensor without any issue.
mortymouse said:
So after reading a bit on lots of different threads here and many other boards, I decided to pick up a couple of the LUVVITT Tempered Glass screen protectors.
I ordered from Amazon and got them for $10 each and free shipping (Prime)
I gotta say, it was the easiest install I have ever done. I started off with the hinge method but I used painters tape and it fell off and I just lined everything up and pushed down in the middle and watched the self adhesive. It went on VERY easy. I did this in a kitchen, (not in the bathroom with hot shower on for the steam) and I didn't get a single piece of lint on either of the installs.
Mine were cut essentially perfect. Cut outs were right on and everything went together pretty much perfectly. As a note, there were a few tiny bubbles in certain areas. I thought at first it was dust but pushed lightly down and it would disappear. Over the next 24 hours they vanished and the protector is now smooth as glass.
I do notice that it does seem to get smudges and some fingerprints, but with a quick swipe of a microfiber cloth (included) or an Oakley glass bag (which I always have on me) they disappear.
This really is a great buy over the glass that costs 2-3 times a much. I recommend this product if you are looking for a screen protector and want more but don't want to pay $30 for it. This is pretty dang good, as good as the ZAGG that is on my buddies phone. We compared them and you cant tell the difference at all.
Bought them here:
http://www.amazon.com/gp/product/B00IKRHCCY/ref=oh_details_o02_s00_i00?ie=UTF8&psc=1
Click to expand...
Click to collapse
Thanks for your input. I just ordered mine, and it should be here within the next couple hours. I will be installing and I will do give my opinion on it also. I recently had the ZAGG glass on my HTC ONE M8, and it was absolute amazing. Only gripe with the ZAGG was the cost....which was around 43$, but luckily I was able to get my money back.
dw4 said:
Isn't 9H hardness a little bit too high ? i mean yeah it's gonna be very scratch resistant but it will break very easily too...
Click to expand...
Click to collapse
Not sure why you would want it to be less hard? Understand, the glass is so thin, it almost looks like plastic.
njan_ivide said:
How easy/obstructive is the home button cutout? I am curious if you can use the fingerprint sensor without any issue.
Click to expand...
Click to collapse
I use my fingerprint scanner everyday, it doesn't interfere at all. The scanner itself isn't the best, but it works the same with our without the protector.
nickhowell25 said:
Thanks for your input. I just ordered mine, and it should be here within the next couple hours. I will be installing and I will do give my opinion on it also. I recently had the ZAGG glass on my HTC ONE M8, and it was absolute amazing. Only gripe with the ZAGG was the cost....which was around 43$, but luckily I was able to get my money back.
Click to expand...
Click to collapse
You will like it. Now that I have used it for a a while I forget its even there. Putting a care on it didn't hurt it either, the rounded corners do the trick.
mortymouse said:
Not sure why you would want it to be less hard? Understand, the glass is so thin, it almost looks like plastic.
I use my fingerprint scanner everyday, it doesn't interfere at all. The scanner itself isn't the best, but it works the same with our without the protector.
You will like it. Now that I have used it for a a while I forget its even there. Putting a care on it didn't hurt it either, the rounded corners do the trick.
Click to expand...
Click to collapse
Mortymouse,
I love it man! I just installed. I recommend to all. I had the ZAGG, and they are virtually the same except the price. ZAGG 39.99 and LUVVIT 12.99... I will let you all take your pick. Thanks for the recommendation
nickhowell25 said:
Mortymouse,
I love it man! I just installed. I recommend to all. I had the ZAGG, and they are virtually the same except the price. ZAGG 39.99 and LUVVIT 12.99... I will let you all take your pick. Thanks for the recommendation
Click to expand...
Click to collapse
You got it!
mortymouse said:
Not sure why you would want it to be less hard? Understand, the glass is so thin, it almost looks like plastic.
Click to expand...
Click to collapse
The harder it is the easier it breaks, from tension or from shock.
But, hardness gives resistance to scratches, because any material would need to have the same or a higher hardness to be able to scratch it.
So it depends on what you want, gorilla glass has a hardness of 7, it means that the only the things with a higher number will be able to scratch it.
When you take a look at gorilla glass, it breaks very easily, the perfect hardness for a glass protector should be a little higher than 7.
That way in case of shock the glass protector, having a little higher hardness, will dampen the shock by breaking before the glass.
dw4 said:
The harder it is the easier it breaks, from tension or from shock.
But, hardness gives resistance to scratches, because any material would need to have the same or a higher hardness to be able to scratch it.
So it depends on what you want, gorilla glass has a hardness of 7, it means that the only the things with a higher number will be able to scratch it.
When you take a look at gorilla glass, it breaks very easily, the perfect hardness for a glass protector should be a little higher than 7.
That way in case of shock the glass protector, having a little higher hardness, will dampen the shock by breaking before the glass.
Click to expand...
Click to collapse
Interesting, I have not ever thought that much about it. This type of glass bends, its almost scratch proof and its shatter proof. If you drop your phone with it on, it will shatter and leave your digitizer unharmed. The hardness rating has more to do with the scratching, etc. You wont find a glass protector with under 9H and its way better than having a normal screen protector as it prevents your screen from shattering.
mortymouse said:
Interesting, I have not ever thought that much about it. This type of glass bends, its almost scratch proof and its shatter proof. If you drop your phone with it on, it will shatter and leave your digitizer unharmed. The hardness rating has more to do with the scratching, etc. You wont find a glass protector with under 9H and its way better than having a normal screen protector as it prevents your screen from shattering.
Click to expand...
Click to collapse
The only glass protecter i ever had was a 5 hardness and it could barely bend, it was just like glass they shiped it in a armored box lol ( just kiddin ) so it wouldn't break during shipping.
Well if we all agreed, then life wouldn't be very interesting.
Thanks for this. I bought an Iloome for 25$ for my S4 and I thought that was a tad high... Especially since I broke it a month in. But it was my fault. 10$ is way more palatable.
AuGmENTor said:
Thanks for this. I bought an Iloome for 25$ for my S4 and I thought that was a tad high... Especially since I broke it a month in. But it was my fault. 10$ is way more palatable.
Click to expand...
Click to collapse
Happy to pass good deals on especially whenever the product works!